-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
After reboot with 2.6.17 dmesg is overflowed with the above. 2.6.16.20 was OK.
Please let me know what additional information may be useful; for now I
simply commented out this printk. dmesg, lsusb and lspci follow.
00:00.0 0600: 10b9:1644 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [b0] AGP version 2.0
Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [a4] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 0604: 10b9:5247
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f7f00000-fdffffff
Prefetchable memory behind bridge: 3c000000-3c0fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 0c03: 10b9:5237 (rev 03) (prog-if 10)
Subsystem: 1179:0004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7eff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 0101: 10b9:5229 (rev c3) (prog-if f0)
Subsystem: 1179:0004
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 255
Region 4: I/O ports at eff0 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 0401: 10b9:5451 (rev 01)
Subsystem: 1179:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR+ <PERR+
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ed00 [size=256]
Region 1: Memory at f7efe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 0601: 10b9:1533
Subsystem: 1179:0004
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 0680: 10b9:7101
Subsystem: 1179:0001
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:0a.0 0200: 8086:1229 (rev 08)
Subsystem: 1179:0003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7efd000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at eb40 [size=64]
Region 2: Memory at f7d00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:10.0 0607: 104c:ac50 (rev 01)
Subsystem: 12a3:ab01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 3c100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 30000000-31fff000 (prefetchable)
Memory window 1: 32000000-33fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:11.0 0607: 1179:0617 (rev 32)
Subsystem: 1179:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 3c101000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=0
Memory window 0: 34000000-35fff000 (prefetchable)
Memory window 1: 36000000-37fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:11.1 0607: 1179:0617 (rev 32)
Subsystem: 1179:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 3c102000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=0a, subordinate=0d, sec-latency=0
Memory window 0: 38000000-39fff000 (prefetchable)
Memory window 1: 3a000000-3bfff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:12.0 0880: 1179:0805 (rev 03)
Subsystem: 1179:0001
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7cffe00 (32-bit, non-prefetchable) [size=512]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 0300: 1023:8820 (rev 82)
Subsystem: 1179:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 8
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=32M]
Region 1: Memory at fbc00000 (32-bit, non-prefetchable) [size=4M]
Region 2: Memory at f8000000 (32-bit, non-prefetchable) [size=32M]
Region 3: Memory at f7ff8000 (32-bit, non-prefetchable) [size=32K]
[virtual] Expansion ROM at 3c000000 [disabled] [size=64K]
Capabilities: [80] AGP version 2.0
Status: RQ=33 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [90] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
{pts/0}% lsusb -vv
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.17-1avb ohci_hcd
iProduct 2 OHCI Host Controller
iSerial 1 0000:00:02.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
dmesg:
Linux version 2.6.17-1avb (bor@cooker) (gcc version 4.1.1 20060518
(prerelease)) #2 Sun Jun 18 15:54:15 MSD 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ef60000 (usable)
BIOS-e820: 000000001ef60000 - 000000001ef70000 (ACPI data)
BIOS-e820: 000000001ef70000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
495MB LOWMEM available.
On node 0 totalpages: 126816
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 122720 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 TOSHIB ) @ 0x000f0090
ACPI: RSDT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef60000
ACPI: FADT (v002 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef60054
ACPI: DSDT (v001 TOSHIB 4000 0x20020417 MSFT 0x0100000a) @ 0x00000000
ACPI: PM-Timer IO Port: 0xee08
Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
Built 1 zonelists
Kernel command line: root=/dev/hda2 pinit hdc=ide-cd resume=/dev/hda1
splash=silent elevator=cfq vga=791 3
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (013e4000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 747.740 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 499180k/507264k available (1663k kernel code, 7456k reserved, 795k
data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1496.77 BogoMIPS (lpj=748388)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Coppermine) stepping 0a
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 0k freed
ACPI: setting ELCR to 0200 (from 0a00)
checking if image is initramfs... it is
Freeing initrd memory: 230k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfe5ae, last bus=5
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region ee00-ee3f claimed by ali7101 ACPI
PCI quirk: region ef00-ef1f claimed by ali7101 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to [email protected] cc [email protected])
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f7f00000-fdffffff
PREFETCH window: 3c000000-3c0fffff
PCI: Bus 2, cardbus bridge: 0000:00:10.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 30000000-31ffffff
MEM window: 32000000-33ffffff
PCI: Bus 6, cardbus bridge: 0000:00:11.0
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 34000000-35ffffff
MEM window: 36000000-37ffffff
PCI: Bus 10, cardbus bridge: 0000:00:11.1
IO window: 00002000-000020ff
IO window: 00002400-000024ff
PREFETCH window: 38000000-39ffffff
MEM window: 3a000000-3bffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:10.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
PCI: Enabling device 0000:00:11.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKA] -> GSI 11 (level, low) ->
IRQ 11
PCI: Enabling device 0000:00:11.1 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:11.1[B] -> Link [LNKB] -> GSI 11 (level, low) ->
IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1150642545.524:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
vesafb: framebuffer at 0xfc000000, mapped to 0xdf880000, using 3072k, total
16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:775e
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
COM USB1 ASND VIY0 VIY1 LAN MPC0 MPC1 NOV0 LID
ACPI: (supports S0 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 176k freed
Write protecting the kernel read-only data: 516k
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
input: AT Translated Set 2 keyboard as /class/input/input0
ALI15X3: IDE controller at PCI slot 0000:00:04.0
ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI
ALI15X3: chipset revision 195
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xeff0-0xeff7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xeff8-0xefff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N020ATDA04-0, ATA DISK drive
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB) w/1806KiB Cache, CHS=38760/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKG] -> GSI 11 (level, low) ->
IRQ 11
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 11, io mem 0xf7eff000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected ALi M1644 chipset
agpgart: AGP aperture is 64M @ 0xf0000000
ohci_hcd 0000:00:02.0: wakeup
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
Yenta: CardBus bridge found at 0000:00:10.0 [12a3:ab01]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:10.0, mfunc 0x01000002, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000059
ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKA] -> GSI 11 (level, low) ->
IRQ 11
Yenta: CardBus bridge found at 0000:00:11.0 [1179:0001]
ohci_hcd 0000:00:02.0: wakeup
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000007
ohci_hcd 0000:00:02.0: wakeup
pccard: PCMCIA card inserted into slot 0
ohci_hcd 0000:00:02.0: wakeup
cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcbfff 0xe0000-0xfffff
cs: memory probe 0x60000000-0x60ffffff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia0.0
ACPI: PCI Interrupt 0000:00:11.1[B] -> Link [LNKB] -> GSI 11 (level, low) ->
IRQ 11
Yenta: CardBus bridge found at 0000:00:11.1 [1179:0001]
wlags49_h1_cs v7.18 for PCMCIA, 03/31/2004 14:31:00 by Agere Systems,
http://www.agere.com
*** Modified for kernel 2.6 by Andrey Borzenkov <[email protected]> $Revision:
22 $
*** Station Mode (STA) Support: YES
*** Access Point Mode (AP) Support: YES
ohci_hcd 0000:00:02.0: wakeup
eth0: PRI 31 variant 2 version 9.48
eth0: NIC 5 variant 2 version 1.02
eth0: Wireless, io_addr 0x100, irq 11, mac_address 00:02:2D:26:95:6C
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000007
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Battery Slot [BAT2] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Fan [FAN] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ohci_hcd 0000:00:02.0: wakeup
ACPI: Thermal Zone [THRM] (53 C)
toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18
toshiba_acpi: HCI method: \_SB_.VALD.GHCI
ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
Adding 500432k swap on /dev/hda1. Priority:-1 extents:1 across:500432k
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
loop: loaded (max 8 devices)
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
hdc: ATAPI 24X DVD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.0: wakeup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2.2 (GNU/Linux)
iD8DBQFElW8WR6LMutpd94wRApdPAJ45BIDoOzPab3YncJ1MXO0RWyHZeQCfSyli
LqZY+QERkJQBKtw/Qr/w5Xg=
=nQS6
-----END PGP SIGNATURE-----
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
