Fix a few spelling errors.
Signed-off-by: Bjorn Helgaas <[email protected]>
Index: rc5-mm3/drivers/block/cciss.c
===================================================================
--- rc5-mm3.orig/drivers/block/cciss.c 2006-06-14 15:16:13.000000000 -0600
+++ rc5-mm3/drivers/block/cciss.c 2006-06-14 15:16:44.000000000 -0600
@@ -129,7 +129,7 @@
{ 0x3215103C, "Smart Array E200i", &SA5_access},
};
-/* How long to wait (in millesconds) for board to go into simple mode */
+/* How long to wait (in milliseconds) for board to go into simple mode */
#define MAX_CONFIG_WAIT 30000
#define MAX_IOCTL_CONFIG_WAIT 1000
@@ -1117,7 +1117,7 @@
*
* Right now I'm using the getgeometry() function to do this, but this
* function should probably be finer grained and allow you to revalidate one
- * particualar logical volume (instead of all of them on a particular
+ * particular logical volume (instead of all of them on a particular
* controller).
*/
static int revalidate_allvol(ctlr_info_t *host)
@@ -1260,7 +1260,7 @@
return;
- /* Get information about the disk and modify the driver sturcture */
+ /* Get information about the disk and modify the driver structure */
size_buff = kmalloc(sizeof( ReadCapdata_struct), GFP_KERNEL);
if (size_buff == NULL)
goto mem_msg;
@@ -1335,7 +1335,7 @@
}
/* This function will add and remove logical drives from the Logical
- * drive array of the controller and maintain persistancy of ordering
+ * drive array of the controller and maintain persistency of ordering
* so that mount points are preserved until the next reboot. This allows
* for the removal of logical drives in the middle of the drive array
* without a re-ordering of those drives.
@@ -1482,7 +1482,7 @@
* clear_all = This flag determines whether or not the disk information
* is going to be completely cleared out and the highest_lun
* reset. Sometimes we want to clear out information about
- * the disk in preperation for re-adding it. In this case
+ * the disk in preparation for re-adding it. In this case
* the highest_lun should be left unchanged and the LunID
* should not be cleared.
*/
@@ -2597,7 +2597,7 @@
return IRQ_HANDLED;
}
/*
- * We cannot read the structure directly, for portablity we must use
+ * We cannot read the structure directly, for portability we must use
* the io functions.
* This is for debug only.
*/
@@ -2620,9 +2620,9 @@
readl(&(tb->TransportActive)));
printk(" Requested transport Method = 0x%x\n",
readl(&(tb->HostWrite.TransportRequest)));
- printk(" Coalese Interrupt Delay = 0x%x\n",
+ printk(" Coalesce Interrupt Delay = 0x%x\n",
readl(&(tb->HostWrite.CoalIntDelay)));
- printk(" Coalese Interrupt Count = 0x%x\n",
+ printk(" Coalesce Interrupt Count = 0x%x\n",
readl(&(tb->HostWrite.CoalIntCount)));
printk(" Max outstanding commands = 0x%d\n",
readl(&(tb->CmdsOutMax)));
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
