Dual via-rhine on EPIA PD6000E

[Wojciech Kromer <wojciech.kromer@dgt.com.pl>]

Hi. I have two differnent via-rhine on EPIA board. Second one is now 
working on my 2.6.15 kernel.

Why there are different io adresses in lspci dmesg and ifconfig?
Any idea why it's not working???


Here are some additional info:

#lspci -v
...
0000:00:0f.0 Ethernet controller: VIA Technologies, Inc. VT6105 
[Rhine-III] (rev
8b)
       Subsystem: VIA Technologies, Inc.: Unknown device 0106
       Flags: bus master, medium devsel, latency 32, IRQ 10
       I/O ports at d000 [size=256]
       Memory at de000000 (32-bit, non-prefetchable) [size=256]
       Capabilities: [44] Power Management version 2
....
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 
[Rhine-II] (rev
74)
       Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded 
Ethernet Con
troller on VT8235
       Flags: bus master, medium devsel, latency 32, IRQ 11
       I/O ports at e400 [size=256]
       Memory at de002000 (32-bit, non-prefetchable) [size=256]
       Capabilities: [40] Power Management version 2





#ifconfig

eth0      Link encap:Ethernet  HWaddr 00:40:63:DB:86:85 
         inet addr:192.168.6.156  Bcast:192.168.6.255  Mask:255.255.255.0
         inet6 addr: fe80::240:63ff:fedb:8685/64 Scope:Link
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:2323562 errors:0 dropped:0 overruns:0 frame:0
         TX packets:474569 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:3145097604 (2.9 GiB)  TX bytes:98221200 (93.6 MiB)
         Interrupt:10 Base address:0xe000

eth1      Link encap:Ethernet  HWaddr 00:40:63:DB:86:88 
         UP BROADCAST MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
         Interrupt:11 Base address:0x4000


#dmesg
...
...
eth0: VIA Rhine III at 0xde000000, 00:40:63:db:86:85, IRQ 10.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, 
low) -> IRQ 11
eth1: VIA Rhine II at 0xde002000, 00:40:63:db:86:88, IRQ 11.
eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
.....

PS  now second cable is disconnected, but there was a link on eth1 too




-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/