Re: how to set this in the future

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Alan Cox wrote:

On Sad, 2006-05-13 at 16:37 -0400, Stephen Clark wrote:
Hello List,

I need to use ide0=ata66 but I get the following:

ide_setup: ide0=ata66 -- OBSOLETE OPTION, WILL BE REMOVED SOON!

what will replace this option?

drivers/scsi/libata .. if I have anything to do with it 8)

Why do you need to use ide0=ata66. What is the hardware requirement that
causes this ?

Alan


I have a hp pavilion laptop n5430 with an ali chipset. I have a hitachi drive that will do udma100 - the docs on my laptop say it will do udma4 but linux by default is setting it to
udma2.



00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/
V+]
       Subsystem: ALi Corporation ALi M1533 Aladdin IV/V ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort
- <MAbort- >SERR- <PERR-
       Latency: 0
       Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c3) (prog-if 8a [Master Se
cP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort
- <MAbort- >SERR- <PERR-
       Latency: 64 (500ns min, 1000ns max)
       Interrupt: pin A routed to IRQ 255
       Region 4: I/O ports at 1000 [size=16]
       Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Regards,
Steve

--

"They that give up essential liberty to obtain temporary safety, deserve neither liberty nor safety." (Ben Franklin)

"The course of history shows that as a government grows, liberty decreases." (Thomas Jefferson)



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux