Hi, Roland - Here is a series of patches to bring the ipath driver up to date. I believe you may already have two of them (but I've included them just in case), but the others should all be new. They apply on top of Linus's current -git. Cheers, <b
- Follow-Ups:
- Re: [PATCH 0 of 53] ipath driver updates for 2.6.17-rc4
- From: Roland Dreier <[email protected]>
- Re: [openib-general] [PATCH 0 of 53] ipath driver updates for 2.6.17-rc4
- From: Roger Heflin <[email protected]>
- [PATCH 7 of 53] ipath - cap maximum number of AHs
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 10 of 53] ipath - require capabilities when creating a QP
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 16 of 53] ipath - fix reporting of driver version to userspace
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 14 of 53] ipath - forbid empty MRs
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 15 of 53] ipath - make some maximum values more sane
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 1 of 53] ipath - fix spinlock recursion bug
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 20 of 53] ipath - more sharing between RC and UC code
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 30 of 53] ipath - count VL15 packet drops due to bad VL or lack of buffers
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 34 of 53] ipath - fix occasional hangs in SDP
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 22 of 53] ipath - fix "many lost ticks" warning
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 28 of 53] ipath - forbid setting of invalid MLID
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 31 of 53] ipath - forbid sending of bad packet sizes
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 19 of 53] ipath - replace uses of LIST_POISON
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 24 of 53] ipath - count dropped VL15 packets
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 29 of 53] ipath - remove redundant register read
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 26 of 53] ipath - treat PE800 rev1 and rev2 as similar
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 21 of 53] ipath - use phys_to_virt instead of bus_to_virt
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 25 of 53] ipath - remove some duplicated lines of code
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 42 of 53] ipath - increment pointer properly when doing a diag read
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 40 of 53] ipath - remember to drop spinlock
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 49 of 53] ipath - NULL-terminate pci_device_id table
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 47 of 53] ipath - fix problem with lost interrupts on HT-400
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 18 of 53] ipath - make max mcast sizes configurable
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 37 of 53] ipath - name zero counter offsets consistently
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 27 of 53] ipath - fix accounting of data packets with bad VLs
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 32 of 53] ipath - fix NULL dereference during cleanup
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 33 of 53] ipath - clean up some comments
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 39 of 53] ipath - count PE800 receive interrupts on user ports
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 45 of 53] ipath - fix memory leak when create of QP fails
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 50 of 53] ipath - reduce maximum table sizes
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 48 of 53] ipath - QP should ignore receive queue size if SRQ specified
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 44 of 53] ipath - allow diags on any unit
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 51 of 53] ipath - fix reporting of vendor ID and a few other trivial bits
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 53 of 53] ipath - add memory barrier when waiting for writes
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 52 of 53] ipath - register as IB device owner
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 2 of 53] ipath - purge sps_lid and sps_mlid arrays, and /sys entries
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 5 of 53] ipath - forbid creation of AHs with illegal ports
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 38 of 53] ipath - SRQ compliance checks
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 6 of 53] ipath - forbid creation of AH with DLID of 0
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 11 of 53] ipath - don't modify QP if changes fail
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 8 of 53] ipath - cap number of CQEs
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 12 of 53] ipath - reduce overhead of receive interrupts
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 13 of 53] ipath - limit number of SGEs and WRs per QP
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 35 of 53] ipath - some interrelated stability and cleanliness fixes
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 9 of 53] ipath - cap number of CQs
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 43 of 53] ipath - fix memory leak when creating a QP fails
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 23 of 53] ipath - [TRIVIAL] typo fixes
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 36 of 53] ipath - count local link integrity errors
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 41 of 53] ipath - disable interrupts while holding spinlock in RWQE get
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 46 of 53] ipath - enable GPIO interrupt on HT-460
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 17 of 53] ipath - fail properly if GID missing
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 3 of 53] ipath - report max MR and QP sizes based on table sizes
- From: "Bryan O'Sullivan" <[email protected]>
- [PATCH 4 of 53] ipath - cap number of PDs that can be allocated
- From: "Bryan O'Sullivan" <[email protected]>
- Re: [PATCH 0 of 53] ipath driver updates for 2.6.17-rc4
- Prev by Date: [PATCH 3 of 53] ipath - report max MR and QP sizes based on table sizes
- Next by Date: [PATCH 17 of 53] ipath - fail properly if GID missing
- Previous by thread: sdhci needs card to be present when loading module.
- Next by thread: [PATCH 4 of 53] ipath - cap number of PDs that can be allocated
- Index(es):