I saw this on Fedora kernel 2.6.16-1.2182_FC6, which is based on
2.6.17-rc3, on a Compaq Presario X1050 laptop:
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C046] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C046] bus is 0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
It said to report it, so I'm reporting it :-) Attached is the dmesg
without the option, dmesg with the option, and lspci output.
--
Robert Hancock Saskatoon, SK, Canada
To email, remove "nospam" from [email protected]
Home Page: http://www.roberthancock.com/
Linux version 2.6.16-1.2182_FC6 ([email protected]) (gcc version 4.1.0 20060425 (Red Hat 4.1.0-11)) #1 SMP Mon May 1 23:02:51 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved)
BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS)
BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 131024
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126928 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000)
Built 1 zonelists
Kernel command line: ro root=/dev/VolGroup00/LogVol00
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0150b000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0737000 soft=c0717000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1395.696 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512384k/524096k available (2030k kernel code, 11124k reserved, 857k data, 236k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2795.04 BogoMIPS (lpj=5590088)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f1bf 00000000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: setting ELCR to 0200 (from 0c20)
CPU0: Intel(R) Pentium(R) M processor 1400MHz stepping 05
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 1651k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C046] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C046] bus is 0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.C046._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C047._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C058._PRT]
ACPI: Embedded Controller [C0EA] (gpe 28) interrupt mode.
ACPI: Power Resource [C18D] (on)
ACPI: Power Resource [C195] (on)
ACPI: Power Resource [C19C] (on)
ACPI: Power Resource [C1A6] (on)
ACPI: PCI Interrupt Link [C0C2] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C3] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C4] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C5] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C6] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10) *11
ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C9] (IRQs *5 10)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0d: ioport range 0x1100-0x113f has been reserved
pnp: 00:0d: ioport range 0x1200-0x121f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: 90400000-904fffff
PREFETCH window: 98000000-9fffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 00002800-000028ff
IO window: 00002c00-00002cff
PREFETCH window: 30000000-31ffffff
MEM window: 34000000-35ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: 90000000-903fffff
PREFETCH window: 30000000-31ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 327680 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1146604655.904:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 9E3DB553A9564D1D
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 256M @ 0xb0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x4c40-0x4c47, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x4c48-0x4c4f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG MP0804H, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 156368016 sectors (80060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44
Yenta: ISA IRQ mask 0x08d8, PCI irq 5
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:C1A3,PNP0f13:C1A4] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
initcall at 0xc043d631: software_resume+0x0/0x16c(): returned with error code -2
ACPI wakeup devices:
C058 C1AD C1A3 C1A4 C0AC C0B3 C0B4 C0B5 C0E7 C136
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 236k freed
Write protecting the kernel read-only data: 379k
input: AT Translated Set 2 keyboard as /class/input/input0
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: [email protected]
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input1
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1146604660.956:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 7 roles, 1177 types, 139 bools, 1 sens, 256 cats
security: 55 classes, 39352 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1146604661.292:3): policy loaded auid=4294967295
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
hw_random: cannot enable RNG, aborting
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 54630 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.6 to 64
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[email protected]>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.1.1
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 5
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0C5] -> GSI 5 (level, low) -> IRQ 5
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
8139too Fast Ethernet driver 0.9.27
cs: IO port probe 0x100-0x3af: excluding 0x140-0x14f 0x200-0x20f 0x378-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Floppy drive(s): fd0 is 1.44M
USB Universal Host Controller Interface driver v3.0
ieee1394: Initialized config rom entry `ip1394'
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
8139too: pci dev 0000:02:01.0 (id 10ec:8139 rev 20) is an enhanced 8139C+ chip
8139too: Use the "8139cp" driver for improved performance and stability.
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
8139too: 0000:02:01.0: unknown chip version, assuming RTL-8139
8139too: 0000:02:01.0: TxConfig = 0x74800000
eth1: RealTek RTL8139 at 0xe0a2c000, 00:02:3f:65:4d:74, IRQ 10
eth1: Identified 8139 chip type 'RTL-8139'
ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 10, io base 0x000048c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C5] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 5, io base 0x000048e0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 5, io base 0x00004c00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C9] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 5, io mem 0xa0000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[90200000-902007ff] Max Packet=[2048] IR/IT contexts=[4/8]
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f383800c298]
floppy0: no floppy controllers found
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: AC Adapter [C134] (on-line)
ACPI: Battery Slot [C11F] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [C1BE]
ACPI: Lid Switch [C136]
ibm_acpi: ec object not found
ACPI: Video Device [C0D0] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:1048568k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (4094 buckets, 32752 max) - 224 bytes per conntrack
eth0: link down
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10
[drm] Initialized radeon 1.24.0 20060225 on minor 0
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Setting GART location based on old memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 2 usecs
audit(1146626344.404:4): avc: denied { use } for pid=2545 comm="bluez-pin" name="[7905]" dev=pipefs ino=7905 scontext=user_u:system_r:bluetooth_helper_t:s0 tcontext=system_u:system_r:xdm_t:s0-s0:c0.c255 tclass=fd
audit(1146626344.404:5): avc: denied { use } for pid=2545 comm="bluez-pin" name="[7905]" dev=pipefs ino=7905 scontext=user_u:system_r:bluetooth_helper_t:s0 tcontext=system_u:system_r:xdm_t:s0-s0:c0.c255 tclass=fd
dev27606: no IPv6 routers present
Linux version 2.6.16-1.2182_FC6 ([email protected]) (gcc version 4.1.0 20060425 (Red Hat 4.1.0-11)) #1 SMP Mon May 1 23:02:51 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved)
BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS)
BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 131024
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126928 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000)
Built 1 zonelists
Kernel command line: ro root=/dev/VolGroup00/LogVol00 pci=assign-busses
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0150b000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0737000 soft=c0717000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1395.687 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512384k/524096k available (2030k kernel code, 11124k reserved, 857k data, 236k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2795.04 BogoMIPS (lpj=5590082)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f1bf 00000000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: setting ELCR to 0200 (from 0c20)
CPU0: Intel(R) Pentium(R) M processor 1400MHz stepping 05
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 1651k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C046] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C046] bus is 0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.C046._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C047._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C058._PRT]
ACPI: Embedded Controller [C0EA] (gpe 28) interrupt mode.
ACPI: Power Resource [C18D] (on)
ACPI: Power Resource [C195] (on)
ACPI: Power Resource [C19C] (on)
ACPI: Power Resource [C1A6] (on)
ACPI: PCI Interrupt Link [C0C2] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C3] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C4] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C5] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C6] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10) *11
ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C9] (IRQs *5 10)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0d: ioport range 0x1100-0x113f has been reserved
pnp: 00:0d: ioport range 0x1200-0x121f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: 90400000-904fffff
PREFETCH window: 98000000-9fffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 00002800-000028ff
IO window: 00002c00-00002cff
PREFETCH window: 30000000-31ffffff
MEM window: 34000000-35ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: 90000000-903fffff
PREFETCH window: 30000000-31ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 327680 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1146605371.900:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 9E3DB553A9564D1D
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 256M @ 0xb0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x4c40-0x4c47, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x4c48-0x4c4f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG MP0804H, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 156368016 sectors (80060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44
Yenta: ISA IRQ mask 0x08d8, PCI irq 5
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:C1A3,PNP0f13:C1A4] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
initcall at 0xc043d631: software_resume+0x0/0x16c(): returned with error code -2
ACPI wakeup devices:
C058 C1AD C1A3 C1A4 C0AC C0B3 C0B4 C0B5 C0E7 C136
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 236k freed
Write protecting the kernel read-only data: 379k
input: AT Translated Set 2 keyboard as /class/input/input0
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: [email protected]
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input1
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1146605376.932:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 7 roles, 1177 types, 139 bools, 1 sens, 256 cats
security: 55 classes, 39352 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1146605377.260:3): policy loaded auid=4294967295
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
hw_random: cannot enable RNG, aborting
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 55046 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.6 to 64
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[email protected]>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.1.1
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 5
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0C5] -> GSI 5 (level, low) -> IRQ 5
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
8139too Fast Ethernet driver 0.9.27
Floppy drive(s): fd0 is 1.44M
cs: IO port probe 0x100-0x3af: excluding 0x140-0x14f 0x200-0x20f 0x378-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
USB Universal Host Controller Interface driver v3.0
ieee1394: Initialized config rom entry `ip1394'
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
8139too: pci dev 0000:02:01.0 (id 10ec:8139 rev 20) is an enhanced 8139C+ chip
8139too: Use the "8139cp" driver for improved performance and stability.
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
8139too: 0000:02:01.0: unknown chip version, assuming RTL-8139
8139too: 0000:02:01.0: TxConfig = 0x74800000
eth1: RealTek RTL8139 at 0xe0962000, 00:02:3f:65:4d:74, IRQ 10
eth1: Identified 8139 chip type 'RTL-8139'
ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 10, io base 0x000048c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C5] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 5, io base 0x000048e0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 5, io base 0x00004c00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C9] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 5, io mem 0xa0000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[90200000-902007ff] Max Packet=[2048] IR/IT contexts=[4/8]
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f383800c298]
floppy0: no floppy controllers found
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: AC Adapter [C134] (on-line)
ACPI: Battery Slot [C11F] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [C1BE]
ACPI: Lid Switch [C136]
ibm_acpi: ec object not found
ACPI: Video Device [C0D0] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:1048568k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (4094 buckets, 32752 max) - 224 bytes per conntrack
eth0: link down
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10
[drm] Initialized radeon 1.24.0 20060225 on minor 0
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Setting GART location based on old memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 2 usecs
audit(1146627062.037:4): avc: denied { use } for pid=2552 comm="bluez-pin" name="[7977]" dev=pipefs ino=7977 scontext=user_u:system_r:bluetooth_helper_t:s0 tcontext=system_u:system_r:xdm_t:s0-s0:c0.c255 tclass=fd
audit(1146627062.037:5): avc: denied { use } for pid=2552 comm="bluez-pin" name="[7977]" dev=pipefs ino=7977 scontext=user_u:system_r:bluetooth_helper_t:s0 tcontext=system_u:system_r:xdm_t:s0-s0:c0.c255 tclass=fd
dev13823: no IPv6 routers present
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at b0000000 (32-bit, prefetchable) [size=256M]
Capabilities: <access denied>
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 90400000-904fffff
Prefetchable memory behind bridge: 98000000-9fffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 48c0 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 48e0 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at 4c00 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 5
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 90000000-903fffff
Prefetchable memory behind bridge: 30000000-31ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 4c40 [size=16]
Region 5: Memory at 32000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 4c20 [size=32]
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 4000 [size=256]
Region 1: I/O ports at 4880 [size=64]
Region 2: Memory at a0200000 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at a0300000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01) (prog-if 00 [Generic])
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 4400 [size=256]
Region 1: I/O ports at 4800 [size=128]
Capabilities: <access denied>
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 Lf [FireGL 9000] (rev 01) (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 98000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at 90400000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at 90420000 [disabled] [size=128K]
Capabilities: <access denied>
02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (8000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 90200000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at 2400 [size=128]
Capabilities: <access denied>
02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 20)
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (8000ns min, 16000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at 90300000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
Subsystem: Hewlett-Packard Company Unknown device 12f5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (750ns min, 6000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 90000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
02:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller
Subsystem: Compaq Computer Corporation Unknown device 0860
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 90100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 30000000-31fff000 (prefetchable)
Memory window 1: 34000000-35fff000
I/O window 0: 00002800-000028ff
I/O window 1: 00002c00-00002cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
