Hello.
Fix the broken hotswap code: on HPT37x it caused RESET- to glitch when
tristating the bus (the MISC control 3/6 and soft control 2 need to be
written to in the certain order), and for HPT36x the obsolete
HDIO_TRISTATE_HWIF ioctl() handler was called instead which treated the state
argument wrong. Also, get rid of the soft control reg. 1 wtite to enable IDE
interrupt -- this is done in init_hpt37x() already...
Have been tested on HPT370 and 371N. Should apply on top of the HPT37x
timing table fix.
MBR, Sergei
Signed-off-by: Sergei Shtylyov <[email protected]>
Index: linus/drivers/ide/pci/hpt366.c
===================================================================
--- linus.orig/drivers/ide/pci/hpt366.c
+++ linus/drivers/ide/pci/hpt366.c
@@ -71,6 +71,8 @@
* needed and had many modes over- and underclocked, HPT372 33 MHz table was
* for 66 MHz and 50 MHz table missed UltraDMA mode 6, HPT374 33 MHz table was
* really for 50 MHz; switch to using HPT372 tables for HPT374...
+ * - fix the hotswap code: it caused RESET- to glitch when tristating the bus,
+ * and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead
* <[email protected]>
*
*/
@@ -954,101 +956,68 @@ static void hpt3xxn_rw_disk(ide_drive_t
hpt3xxn_set_clock(hwif, wantclock);
}
-/*
- * Since SUN Cobalt is attempting to do this operation, I should disclose
- * this has been a long time ago Thu Jul 27 16:40:57 2000 was the patch date
- * HOTSWAP ATA Infrastructure.
- */
-
-static void hpt3xx_reset (ide_drive_t *drive)
-{
-}
-
-static int hpt3xx_tristate (ide_drive_t * drive, int state)
-{
- ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- u8 reg59h = 0, reset = (hwif->channel) ? 0x80 : 0x40;
- u8 regXXh = 0, state_reg= (hwif->channel) ? 0x57 : 0x53;
-
- pci_read_config_byte(dev, 0x59, ®59h);
- pci_read_config_byte(dev, state_reg, ®XXh);
-
- if (state) {
- (void) ide_do_reset(drive);
- pci_write_config_byte(dev, state_reg, regXXh|0x80);
- pci_write_config_byte(dev, 0x59, reg59h|reset);
- } else {
- pci_write_config_byte(dev, 0x59, reg59h & ~(reset));
- pci_write_config_byte(dev, state_reg, regXXh & ~(0x80));
- (void) ide_do_reset(drive);
- }
- return 0;
-}
-
/*
- * set/get power state for a drive.
- * turning the power off does the following things:
- * 1) soft-reset the drive
- * 2) tri-states the ide bus
+ * Set/get power state for a drive.
*
- * when we turn things back on, we need to re-initialize things.
+ * When we turn the power back on, we need to re-initialize things.
*/
#define TRISTATE_BIT 0x8000
-static int hpt370_busproc(ide_drive_t * drive, int state)
+
+static int hpt3xx_busproc(ide_drive_t *drive, int state)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = hwif->pci_dev;
- u8 tristate = 0, resetmask = 0, bus_reg = 0;
- u16 tri_reg;
+ u8 tristate, resetmask, bus_reg = 0;
+ u16 tri_reg = 0;
hwif->bus_state = state;
if (hwif->channel) {
/* secondary channel */
- tristate = 0x56;
- resetmask = 0x80;
+ tristate = 0x56;
+ resetmask = 0x80;
} else {
/* primary channel */
- tristate = 0x52;
+ tristate = 0x52;
resetmask = 0x40;
}
- /* grab status */
+ /* Grab the status. */
pci_read_config_word(dev, tristate, &tri_reg);
pci_read_config_byte(dev, 0x59, &bus_reg);
- /* set the state. we don't set it if we don't need to do so.
- * make sure that the drive knows that it has failed if it's off */
+ /*
+ * Set the state. We don't set it if we don't need to do so.
+ * Make sure that the drive knows that it has failed if it's off.
+ */
switch (state) {
case BUSSTATE_ON:
- hwif->drives[0].failures = 0;
- hwif->drives[1].failures = 0;
- if ((bus_reg & resetmask) == 0)
+ if (!(bus_reg & resetmask))
return 0;
- tri_reg &= ~TRISTATE_BIT;
- bus_reg &= ~resetmask;
- break;
+ hwif->drives[0].failures = hwif->drives[1].failures = 0;
+
+ pci_write_config_byte(dev, 0x59, bus_reg & ~resetmask);
+ pci_write_config_word(dev, tristate, tri_reg & ~TRISTATE_BIT);
+ return 0;
case BUSSTATE_OFF:
- hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
- hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
- if ((tri_reg & TRISTATE_BIT) == 0 && (bus_reg & resetmask))
+ if ((bus_reg & resetmask) && !(tri_reg & TRISTATE_BIT))
return 0;
tri_reg &= ~TRISTATE_BIT;
- bus_reg |= resetmask;
break;
case BUSSTATE_TRISTATE:
- hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
- hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
- if ((tri_reg & TRISTATE_BIT) && (bus_reg & resetmask))
+ if ((bus_reg & resetmask) && (tri_reg & TRISTATE_BIT))
return 0;
tri_reg |= TRISTATE_BIT;
- bus_reg |= resetmask;
break;
+ default:
+ return -EINVAL;
}
- pci_write_config_byte(dev, 0x59, bus_reg);
- pci_write_config_word(dev, tristate, tri_reg);
+ hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
+ hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
+
+ pci_write_config_word(dev, tristate, tri_reg);
+ pci_write_config_byte(dev, 0x59, bus_reg | resetmask);
return 0;
}
@@ -1363,23 +1332,11 @@ static void __devinit init_hwif_hpt366(i
if (serialize && hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
- if (info->revision >= 3) {
- u8 reg5ah = 0;
- pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
- /*
- * set up ioctl for power status.
- * note: power affects both
- * drives on each channel
- */
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt370_busproc;
- } else if (info->revision >= 2) {
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt3xx_tristate;
- } else {
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt3xx_tristate;
- }
+ /*
+ * Set up ioctl for power status.
+ * NOTE: power affects both drives on each channel.
+ */
+ hwif->busproc = &hpt3xx_busproc;
if (!hwif->dma_base) {
hwif->drives[0].autotune = 1;
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
