I think I may have figured out my problem (I hope). I had, a while ago,
upgraded my BIOS, which reset the SATA mode for the controller. It's odd
that the error didn't pop up until I upgraded my drives from dual maxtor
6Y160M0's...
Originally I had the controller set up in the BIOS as "RAID" instead of
IDE, so they didnt' show up on any of the BIOS IDE channels in the BIOS
Setup screen. After the BIOS upgrade, this was overwritten with "Auto"
mode. When I first started having problems it was on "Auto"... I've set
it to "Combined" and "Enhanced", to no avail. (though I may set it to
"Enhanced" and reboot just to see what the kernel messages say.... ) As
of now, I've re-set it to "RAID", and now the kernel outputs the
following on boot. I have not had any issues since making this change.
kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
kernel: ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
kernel: ICH5: IDE controller at PCI slot 0000:00:1f.1
kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
kernel: PCI: setting IRQ 11 as level-triggered
kernel: ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11
(level, low) -> IRQ 11
kernel: ICH5: chipset revision 2
kernel: ICH5: not 100% native mode: will probe irqs later
kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA,
hdb:pio
kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA,
hdd:pio
kernel: hdd: SR244W, ATAPI CD/DVD-ROM drive
kernel: ide1 at 0x170-0x177,0x376 on irq 15
kernel: hdd: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
kernel: Uniform CD-ROM driver Revision: 3.20
kernel: ide-floppy driver 0.99.newide
[...]
kernel: SCSI subsystem initialized
kernel: ACPI: PCI Interrupt 0000:00:1f.2[A] -> Link [LNKC] -> GSI 11
(level, low) -> IRQ 11
kernel: ata1: SATA max UDMA/133 cmd 0xE200 ctl 0xE302 bmdma 0xE600
irq 11
kernel: ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE502 bmdma 0xE608
irq 11
kernel: ata1: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
kernel: ata1: dev 0 configured for UDMA/133
kernel: scsi0 : ata_piix
kernel: ata2: dev 0 ATA-7, max UDMA/133, 586072368 sectors: LBA48
kernel: ata2: dev 0 configured for UDMA/133
kernel: scsi1 : ata_piix
kernel: Vendor: ATA Model: Maxtor 6V300F0 Rev: VA11
kernel: Type: Direct-Access ANSI SCSI
revision: 05
kernel: SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
kernel: SCSI device sda: drive cache: write back
kernel: SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
kernel: SCSI device sda: drive cache: write back
kernel: sda: sda1
kernel: sd 0:0:0:0: Attached scsi disk sda
kernel: Vendor: ATA Model: ST3300831AS Rev: 3.03
kernel: Type: Direct-Access ANSI SCSI
revision: 05
kernel: SCSI device sdb: 586072368 512-byte hdwr sectors (300069 MB)
kernel: SCSI device sdb: drive cache: write back
kernel: SCSI device sdb: 586072368 512-byte hdwr sectors (300069 MB)
kernel: SCSI device sdb: drive cache: write back
kernel: sdb: sdb1
kernel: sd 1:0:0:0: Attached scsi disk sdb
Previously, on "Auto", this is what the kernel would output on boot:
kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
kernel: ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
kernel: ide0: I/O resource 0x1F0-0x1F7 not free.
kernel: ide0: ports already in use, skipping probe
kernel: hdd: SR244W, ATAPI CD/DVD-ROM drive
kernel: ide1 at 0x170-0x177,0x376 on irq 15
kernel: hdd: ATAPI 24X CD-ROM drive, 128kB Cache
kernel: Uniform CD-ROM driver Revision: 3.20
kernel: ide-floppy driver 0.99.newide
[...]
kernel: SCSI subsystem initialized
kernel: ata_piix: combined mode detected
kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
kernel: PCI: setting IRQ 11 as level-triggered
kernel: ACPI: PCI Interrupt 0000:00:1f.2[A] -> Link [LNKC] -> GSI 11
(level, low) -> IRQ 11
kernel: ata: 0x170 IDE port busy
kernel: ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
kernel: input: AT Translated Set 2 keyboard on isa0060/serio0
kernel: ata1: dev 0 ATA, max UDMA/133, 320173056 sectors: lba48
kernel: ata1: dev 1 ATA, max UDMA/133, 320173056 sectors: lba48
kernel: ata1: dev 0 configured for UDMA/133
kernel: ata1: dev 1 configured for UDMA/133
kernel: scsi0 : ata_piix
kernel: Vendor: ATA Model: Maxtor 6Y160M0 Rev: YAR5
kernel: Type: Direct-Access ANSI SCSI
revision: 05
kernel: SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
kernel: SCSI device sda: drive cache: write back
kernel: SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
kernel: SCSI device sda: drive cache: write back
kernel: sda: sda1
kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
kernel: Vendor: ATA Model: Maxtor 6Y160M0 Rev: YAR5
kernel: Type: Direct-Access ANSI SCSI
revision: 05
kernel: SCSI device sdb: 320173056 512-byte hdwr sectors (163929 MB)
kernel: SCSI device sdb: drive cache: write back
kernel: SCSI device sdb: 320173056 512-byte hdwr sectors (163929 MB)
kernel: SCSI device sdb: drive cache: write back
kernel: sdb: sdb1
kernel: Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
lshw also shows the bus and IO memory organized differently, with these
two options:
http://www.societasilluminati.org/hinv2.html : "RAID" mode set in the bios
http://www.societasilluminati.org/hinv.html: "Enhanced" mode set in the bios
Unfortunately, my boot logs have rolled since I got the "Enhanced" listing.
Samuel Masham wrote:
Hi Again All, Alan,
On 17/03/06, Samuel Masham <[email protected]> wrote:
Hi Alan,
On 17/03/06, Alan Cox <[email protected]> wrote:
On Gwe, 2006-03-17 at 13:37 +0900, Samuel Masham wrote:
As you can see from the printk's here this error continues and the for
every access (write?) to the drive you just have to wait for a
timeout.
Eventually the drive will be offlined.
really? I can test that easily enough if nothing else :)
When is it (should it) going to offline the drive? its been spitting
out these messages (about set per min?) for 4 hours at the moment with
no change bar the sector number increasing by 2 each time...
ata1: command 0x35 timeout, stat 0xd1 host_stat 0x61
ata1: translated ATA stat/err 0xd1/00 to SCSI SK/ASC/ASCQ 0xb/47/00
ata1: status=0xd1 { Busy }
SCSI disk error : host 0 channel 0 id 1 lun 0 return code = 8000002
Current sd08:12: sense key Aborted Command
Additional sense indicates Scsi parity error
It thinks there is a communication (eg cable problem), at least that is
how it has mapped the error report. Not something I'd expect to see in
the SATA case on several machines so it could be some kind of setup
error or timing incompatibility in the driver.
Well Its cheep enough to get another cable and test that.
Done. The new short cable showed no difference in behavior.
So left with the timing/setup error... Anyone with any ideas?
What is attached to that controller (SATA and PATA items)
as I said before there are two hardisks
Ata Maxtor 6Y080M0 SCSI sda 0
Ata Maxtor 6V250F0 SCSI sdb 0
(Remember the problem is ONLY with the second drive... and according
to others any in the 6Vxxx series shows this same issue?)
...and there is a cdrom drive attached via pata
(I think its on the same controller... the 6300ESB seems to do just
about everything...)
hdparm -I /dev/hda
/dev/hda:
ATAPI CD-ROM, with removable media
Model Number: SAMSUNG CD-ROM SN-124
Serial Number:
Firmware Revision: N103
Standards:
Likely used CD-ROM ATAPI-1
Configuration:
DRQ response: 50us.
Packet size: 12 bytes
Capabilities:
LBA, IORDY(can be disabled)
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
As Ian mentioned maxtor have release a new version of the drive
firmware ... but... The 6V250F0 drive that shows this lockup IS
running the latest drive firmware which I discovered after a rather
long exchange with Maxtor...
I have had a bit of a look at the sata spec and would just like to
confirm that the drive is configured to disable the NCQ (as the Maxtor
support seemed to stress this point). From what i can see this is done
in the Device Configuration Overlay...
From the spec
4.8. Device Configuration Overlay
4.8.1. Definition
WORD 8: Serial ATA command / feature sets supported
This word enables configuration of command sets and feature sets.
Bit 0 indicates whether native command queuing shall be
supported by the device. When
set to one, the drive shall support native command queuing.
When cleared to zero, drive
support for native command queuing shall be disabled ....
So anyone got any ideas how to read this?
Or anything else to check / try...
Samuel
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
