> Could you just comment out _TMP in kernel or in DSDT,
I think it needs both excisions: If I comment out just the kernel _TMP
calls, the DSDT might slip one in through the interpreter. If I
comment out just the DSDT _TMP calls, then the kernel can still call
_TMP. So instead I modified acpi_evaluate_integer() to return 27 C
(3000 dK) if it's ever asked for a temperature, without doing any
actual work:
--- utils.c.orig 2006-02-27 00:09:35.000000000 -0500
+++ utils.c 2006-03-14 23:36:59.000000000 -0500
@@ -270,7 +270,15 @@ acpi_evaluate_integer(acpi_handle handle
memset(element, 0, sizeof(union acpi_object));
buffer.length = sizeof(union acpi_object);
buffer.pointer = element;
- status = acpi_evaluate_object(handle, pathname, arguments, &buffer);
+ if (strcmp(pathname, "_TMP") != 0)
+ status = acpi_evaluate_object(handle, pathname, arguments, &buffer);
+ else {
+ printk(KERN_INFO PREFIX "acpi_evaluate_integer: Faking _TMP\n");
+ status = AE_OK;
+ element->type = ACPI_TYPE_INTEGER;
+ element->integer.value = 3000; /* 27 C, in deciKelvins */
+ }
+
if (ACPI_FAILURE(status)) {
acpi_util_eval_error(handle, pathname, status);
return_ACPI_STATUS(status);
This diff is in addition to the previous debugging changes to
thermal.c.
> and do several S3 suspend /resume Cycles without remove thermal
> module, I want to make sure we are at right place to drill down.
I repeated yesterday's experiments:
echo 100 > /proc/acpi/thermal_zone/THM0/polling_frequency
modprobe -rv thermal
modprobe thermal zone_to_keep=0 bisect_get_info=1
sleep.sh
with the modified utils.c (being careful to install the new kernel and
reboot, not just reinstall modules, since utils.c is part of the acpi
builtins). And, unlike yesterday (when _TMP was unhacked), there was
no hang. Nor did it hang after five more sleep-wake cycles.
Here's are the dmesgs starting when 'thermal' is loaded at boot
(i.e. with the above patch but no special zone_to_keep etc. params),
and then with the commands above:
# during boot
ACPI: thermal_add: THM0
# next line is from the utils.c modification to return 27 C always
ACPI: acpi_evaluate_integer: Faking _TMP
Execute Method: [\_TZ_.THM0._PSV] (Node c157be48)
Execute Method: [\_TZ_.THM0._TC1] (Node c157bdc8)
Execute Method: [\_TZ_.THM0._TC2] (Node c157bd88)
Execute Method: [\_TZ_.THM0._TSP] (Node c157bd48)
Execute Method: [\_TZ_.THM0._AC0] (Node c157bf48)
Execute Method: [\_TZ_.THM0._SCP] (Node c157bec8)
ACPI: acpi_evaluate_integer: Faking _TMP
ACPI: Thermal Zone [THM0] (27 C)
ACPI: thermal_add: THM2
ACPI: acpi_evaluate_integer: Faking _TMP
Execute Method: [\_TZ_.THM2._AC0] (Node c157bb48)
Execute Method: [\_TZ_.THM2._SCP] (Node c157bac8)
ACPI: acpi_evaluate_integer: Faking _TMP
ACPI: Thermal Zone [THM2] (27 C)
ACPI: thermal_add: THM6
ACPI: acpi_evaluate_integer: Faking _TMP
Execute Method: [\_TZ_.THM6._AC0] (Node c157b908)
Execute Method: [\_TZ_.THM6._SCP] (Node c157b888)
ACPI: acpi_evaluate_integer: Faking _TMP
ACPI: Thermal Zone [THM6] (27 C)
ACPI: thermal_add: THM7
ACPI: acpi_evaluate_integer: Faking _TMP
Execute Method: [\_TZ_.THM7._AC0] (Node c157b6c8)
Execute Method: [\_TZ_.THM7._SCP] (Node c157b648)
ACPI: acpi_evaluate_integer: Faking _TMP
ACPI: Thermal Zone [THM7] (27 C)
ACPI: thermal_add: _TZ
ACPI: acpi_evaluate_integer: Faking _TMP
# booting is done. Now for
# echo 100 > /proc/acpi/thermal_zone/THM0/polling_frequency
ACPI: acpi_evaluate_integer: Faking _TMP
# now "modprobe -rv thermal; modprobe thermal zone_to_keep=0 bisect_get_info=1"
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: thermal_add: THM0
ACPI: acpi_evaluate_integer: Faking _TMP
ACPI: thermal_get_info: got temperature, but bisect_get_info = 1 so exiting
ACPI: acpi_evaluate_integer: Faking _TMP
ACPI: Thermal Zone [THM0] (27 C)
ACPI: thermal_add: THM2
ACPI: thermal_add: ignoring THM2
ACPI: thermal_add: THM6
ACPI: thermal_add: ignoring THM6
ACPI: thermal_add: THM7
ACPI: thermal_add: ignoring THM7
ACPI: thermal_add: _TZ
ACPI: thermal_add: ignoring _TZ
# now sleep.sh
eth0: removing device
Unloaded prism54 driver
PM: Preparing system for mem sleep
Stopping tasks: =======================================================|
Execute Method: [\_SB_.LID0._PSW] (Node c1564808)
Execute Method: [\_SB_.SLPB._PSW] (Node c1564708)
Execute Method: [\_S3_] (Node c157a988)
Execute Method: [\_PTS] (Node c157ab48)
Execute Method: [\_SI_._SST] (Node c157a8c8)
uhci_hcd 0000:00:07.2: suspend_rh
uhci_hcd 0000:00:07.2: uhci_suspend
uhci_hcd 0000:00:07.2: --> PCI D0/legacy
PM: Entering mem sleep
# hit "Fn" key to wake it up
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Back to C!
PM: Finishing wakeup.
Execute Method: [\_GPE._L0B] (Node c157a848)
PCI: Found IRQ 11 for device 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:06.0
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Found IRQ 11 for device 0000:00:02.1
uhci_hcd 0000:00:07.2: PCI legacy resume
PCI: Found IRQ 11 for device 0000:00:07.2
uhci_hcd 0000:00:07.2: uhci_resume
uhci_hcd 0000:00:07.2: uhci_check_and_reset_hc: legsup = 0x2000
uhci_hcd 0000:00:07.2: Performing full reset
usb usb1: root hub lost power or was reset
uhci_hcd 0000:00:07.2: suspend_rh
usb usb1: finish resume
uhci_hcd 0000:00:07.2: wakeup_rh
Restarting tasks...<7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
done
Execute Method: [\_SI_._SST] (Node c157a8c8)
Execute Method: [\_WAK] (Node c157aac8)
Execute Method: [\_TZ_.THM0._PSV] (Node c157be48)
Execute Method: [\_TZ_.THM0._TC1] (Node c157bdc8)
Execute Method: [\_TZ_.THM0._TC2] (Node c157bd88)
Execute Method: [\_TZ_.THM0._TSP] (Node c157bd48)
Execute Method: [\_TZ_.THM0._AC0] (Node c157bf48)
ACPI: acpi_evaluate_integer: Faking _TMP
Execute Method: [\_SI_._SST] (Node c157a8c8)
uhci_hcd 0000:00:07.2: suspend_rh (auto-stop)
Execute Method: [\_SB_.LID0._PSW] (Node c1564808)
Execute Method: [\_SB_.SLPB._PSW] (Node c1564708)
ds: ds_open(socket 0)
ds: ds_open(socket 1)
ds: ds_open(socket 2)
# from explicit 'cardctl eject' in sleep.sh's wake portion (to save battery)
pccard: card ejected from slot 1
PCMCIA: socket e36dac28: *** DANGER *** unable to remove socket power
ds: ds_release(socket 0)
ds: ds_release(socket 1)
ACPI: acpi_evaluate_integer: Faking _TMP
# and I can keep doing 'sleep.sh' with no problem
-Sanjoy
`Never underestimate the evil of which men of power are capable.'
--Bertrand Russell, _War Crimes in Vietnam_, chapter 1.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
