Problem with sata driver

["Sion Khalaf" <Sion@bitband.com>]

Hi,

I am having problem with Sata Drive /dev/sda  

Board from SuperMicro With Nvidia ChipSet - H8DCE
The board has 8 x SATA ports, but only one SATA Drive is connected
(Maxtor 500 GB )

Kernel 2.6.15
I insert the module :  insmod sata_nv.ko
Then, udevstart

Fdisk Output:
-------------------------------------------------------------------
[root@880-TEST root]$ fdisk -l

Disk /dev/hda: 262 MB, 262144000 bytes
16 heads, 32 sectors/track, 1000 cylinders
Units = cylinders of 512 * 512 = 262144 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/hda1   *           1         998      255487+  83  Linux

Disk /dev/sda: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
[root@880-TEST root]$
 
------------------------------------------------------------------------
----
When trying to repartition the disk, I got into hangs.
(Trying to save changes - w )

Attached is the dmesg, since inserting the module.

What is wrong ?

Thank you in advanced,
Sion

************************************************************************
**********

sata_nv 0000:00:07.0: version 0.8
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 11 (level,
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0xC800 ctl 0xC402 bmdma 0xB800 irq 11
ata2: SATA max UDMA/133 cmd 0xC000 ctl 0xBC02 bmdma 0xB808 irq 11
ata1: no device found (phy stat 00000000)
scsi0 : sata_nv
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
ACPI: PCI Interrupt Link [LTIE] enabled at IRQ 9
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LTIE] -> GSI 9 (level, low)
-> IRQ 9
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0xB400 ctl 0xB002 bmdma 0xA400 irq 9
ata4: SATA max UDMA/133 cmd 0xAC00 ctl 0xA802 bmdma 0xA408 irq 9
ata3: no device found (phy stat 00000000)
scsi2 : sata_nv
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata4: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4773 85:7c69 86:3e01 87:4763
88:407f
ata4: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata4: dev 0 configured for UDMA/133
scsi3 : sata_nv
  Vendor: ATA       Model: Maxtor 7H500F0    Rev: HA43
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
 sda:<4>nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed

sd 3:0:0:0: Attached scsi disk sda
sd 3:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt 0000:80:07.0[A] -> Link [LNKB] -> GSI 9 (level, low)
-> IRQ 9
PCI: Setting latency timer of device 0000:80:07.0 to 64
ata5: SATA max UDMA/133 cmd 0xF800 ctl 0xF402 bmdma 0xE800 irq 9
ata6: SATA max UDMA/133 cmd 0xF000 ctl 0xEC02 bmdma 0xE808 irq 9
ata5: no device found (phy stat 00000000)
scsi4 : sata_nv
ata6: no device found (phy stat 00000000)
scsi5 : sata_nv
ACPI: PCI Interrupt 0000:80:08.0[A] -> Link [LNKA] -> GSI 9 (level, low)
-> IRQ 9
PCI: Setting latency timer of device 0000:80:08.0 to 64
ata7: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xD400 irq 9
ata8: SATA max UDMA/133 cmd 0xDC00 ctl 0xD802 bmdma 0xD408 irq 9
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata7: no device found (phy stat 00000000)
scsi6 : sata_nv
ata8: no device found (phy stat 00000000)
scsi7 : sata_nv
ata4: command 0x35 timeout, stat 0xd0 host_stat 0x21
ata4: translated ATA stat/err 0xd0/00 to SCSI SK/ASC/ASCQ 0xb/47/00
ata4: status=0xd0 { Busy }
sd 3:0:0:0: SCSI error: return code = 0x8000002
sda: Current: sense key=0xb
    ASC=0x47 ASCQ=0x0
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
lost page write due to I/O error on sda
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
 sda:<4>ATA: abnormal status 0xD0 on port 0xAC07
ATA: abnormal status 0xD0 on port 0xAC07
ATA: abnormal status 0xD0 on port 0xAC07
[root@880-TEST root]$
************************************************************************
*********
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/