The attached patch documents the Linux kernel's memory barriers.
I've updated it from the comments I've been given.
The per-arch notes sections are gone because it's clear that there are so many
exceptions, that it's not worth having them.
I've added a list of references to other documents.
I've tried to get rid of the concept of memory accesses appearing on the bus;
what matters is apparent behaviour with respect to other observers in the
system.
Interrupts barrier effects are now considered to be non-existent. They may be
there, but you may not rely on them.
I've added a couple of definition sections at the top of the document: one to
specify the minimum execution model that may be assumed, the other to specify
what this document refers to by the term "memory".
Signed-Off-By: David Howells <[email protected]>
---
warthog>diffstat -p1 /tmp/mb.diff
Documentation/memory-barriers.txt | 855 ++++++++++++++++++++++++++++++++++++++
1 files changed, 855 insertions(+)
diff --git a/Documentation/memory-barriers.txt b/Documentation/memory-barriers.txt
new file mode 100644
index 0000000..04c5c88
--- /dev/null
+++ b/Documentation/memory-barriers.txt
@@ -0,0 +1,855 @@
+ ============================
+ LINUX KERNEL MEMORY BARRIERS
+ ============================
+
+Contents:
+
+ (*) Assumed minimum execution ordering model.
+
+ (*) What is considered memory?
+
+ - Cached interactions.
+ - Uncached interactions.
+
+ (*) What are memory barriers?
+
+ (*) Where are memory barriers needed?
+
+ - Accessing devices.
+ - Multiprocessor interaction.
+ - Interrupts.
+
+ (*) Explicit kernel compiler barriers.
+
+ (*) Explicit kernel memory barriers.
+
+ (*) Implicit kernel memory barriers.
+
+ - Locking functions.
+ - Interrupt disabling functions.
+ - Miscellaneous functions.
+
+ (*) Inter-CPU locking barrier effects.
+
+ - Locks vs memory accesses.
+ - Locks vs I/O accesses.
+
+ (*) Kernel I/O barrier effects.
+
+ (*) References.
+
+
+========================================
+ASSUMED MINIMUM EXECUTION ORDERING MODEL
+========================================
+
+It has to be assumed that the conceptual CPU is weakly-ordered in all respects
+but that it will maintain the appearance of program causality with respect to
+itself. Some CPUs (such as i386 or x86_64) are more constrained than others
+(such as powerpc or frv), and so the worst case must be assumed.
+
+This means that it must be considered that the CPU will execute its instruction
+stream in any order it feels like - or even in parallel - provided that if an
+instruction in the stream depends on the an earlier instruction, then that
+earlier instruction must be sufficiently complete[*] before the later
+instruction may proceed.
+
+ [*] Some instructions have more than one effect[**] and different instructions
+ may depend on different effects.
+
+ [**] Eg: changes to condition codes and registers; memory changes; barriers.
+
+A CPU may also discard any instruction sequence that ultimately winds up having
+no effect. For example if two adjacent instructions both load an immediate
+value into the same register, the first may be discarded.
+
+
+Similarly, it has to be assumed that compiler might reorder the instruction
+stream in any way it sees fit, again provided the appearance of causality is
+maintained.
+
+
+==========================
+WHAT IS CONSIDERED MEMORY?
+==========================
+
+For the purpose of this specification what's meant by "memory" needs to be
+defined, and the division between CPU and memory needs to be marked out.
+
+
+CACHED INTERACTIONS
+-------------------
+
+As far as cached CPU vs CPU[*] interactions go, "memory" has to include the CPU
+caches in the system. Although any particular read or write may not actually
+appear outside of the CPU that issued it (the CPU may may have been able to
+satisfy it from its own cache), it's still as if the memory access had taken
+place as far as the other CPUs are concerned since the cache coherency and
+ejection mechanisms will propegate the effects upon conflict.
+
+ [*] Also applies to CPU vs device when accessed through a cache.
+
+The system can be considered logically as:
+
+ <--- CPU ---> : <----------- Memory ----------->
+ :
+ +--------+ +--------+ : +--------+ +-----------+
+ | | | | : | | | | +---------+
+ | CPU | | Memory | : | CPU | | | | |
+ | Core |--->| Access |----->| Cache |<-->| | | |
+ | | | Queue | : | | | |--->| Memory |
+ | | | | : | | | | | |
+ +--------+ +--------+ : +--------+ | | | |
+ : | Cache | +---------+
+ : | Coherency |
+ : | Mechanism | +---------+
+ +--------+ +--------+ : +--------+ | | | |
+ | | | | : | | | | | |
+ | CPU | | Memory | : | CPU | | |--->| Device |
+ | Core |--->| Access |----->| Cache |<-->| | | |
+ | | | Queue | : | | | | | |
+ | | | | : | | | | +---------+
+ +--------+ +--------+ : +--------+ +-----------+
+ :
+ :
+
+The CPU core may execute instructions in any order it deems fit, provided the
+expected program causality appears to be maintained. Some of the instructions
+generate load and store operations which then go into the memory access queue
+to be performed. The core may place these in the queue in any order it wishes,
+and continue execution until it is forced to wait for an instruction to
+complete.
+
+What memory barriers are concerned with is controlling the order in which
+accesses cross from the CPU side of things to the memory side of things, and
+the order in which the effects are perceived to happen by the other observers
+in the system.
+
+
+UNCACHED INTERACTIONS
+---------------------
+
+Note that the above model does not show uncached memory or I/O accesses. These
+procede directly from the queue to the memory or the devices, bypassing any
+cache coherency:
+
+ <--- CPU ---> :
+ : +-----+
+ +--------+ +--------+ : | |
+ | | | | : | | +---------+
+ | CPU | | Memory | : | | | |
+ | Core |--->| Access |--------------->| | | |
+ | | | Queue | : | |------------->| Memory |
+ | | | | : | | | |
+ +--------+ +--------+ : | | | |
+ : | | +---------+
+ : | Bus |
+ : | | +---------+
+ +--------+ +--------+ : | | | |
+ | | | | : | | | |
+ | CPU | | Memory | : | |<------------>| Device |
+ | Core |--->| Access |--------------->| | | |
+ | | | Queue | : | | | |
+ | | | | : | | +---------+
+ +--------+ +--------+ : | |
+ : +-----+
+ :
+
+
+=========================
+WHAT ARE MEMORY BARRIERS?
+=========================
+
+Memory barriers are instructions to both the compiler and the CPU to impose an
+apparent partial ordering between the memory access operations specified either
+side of the barrier. They request that the sequence of memory events generated
+appears to other components of the system as if the barrier is effective on
+that CPU.
+
+Note that:
+
+ (*) there's no guarantee that the sequence of memory events is _actually_ so
+ ordered. It's possible for the CPU to do out-of-order accesses _as long
+ as no-one is looking_, and then fix up the memory if someone else tries to
+ see what's going on (for instance a bus master device); what matters is
+ the _apparent_ order as far as other processors and devices are concerned;
+ and
+
+ (*) memory barriers are only guaranteed to act within the CPU processing them,
+ and are not, for the most part, guaranteed to percolate down to other CPUs
+ in the system or to any I/O hardware that that CPU may communicate with.
+
+
+For example, a programmer might take it for granted that the CPU will perform
+memory accesses in exactly the order specified, so that if a CPU is, for
+example, given the following piece of code:
+
+ a = *A;
+ *B = b;
+ c = *C;
+ d = *D;
+ *E = e;
+
+They would then expect that the CPU will complete the memory access for each
+instruction before moving on to the next one, leading to a definite sequence of
+operations as seen by external observers in the system:
+
+ read *A, write *B, read *C, read *D, write *E.
+
+
+Reality is, of course, much messier. With many CPUs and compilers, this isn't
+always true because:
+
+ (*) reads are more likely to need to be completed immediately to permit
+ execution progress, whereas writes can often be deferred without a
+ problem;
+
+ (*) reads can be done speculatively, and then the result discarded should it
+ prove not to be required;
+
+ (*) the order of the memory accesses may be rearranged to promote better use
+ of the CPU buses and caches;
+
+ (*) reads and writes may be combined to improve performance when talking to
+ the memory or I/O hardware that can do batched accesses of adjacent
+ locations, thus cutting down on transaction setup costs (memory and PCI
+ devices may be able to do this); and
+
+ (*) the CPU's data cache may affect the ordering, though cache-coherency
+ mechanisms should alleviate this - once the write has actually hit the
+ cache.
+
+So what another CPU, say, might actually observe from the above piece of code
+is:
+
+ read *A, read {*C,*D}, write *E, write *B
+
+ (By "read {*C,*D}" I mean a combined single read).
+
+
+It is also guaranteed that a CPU will be self-consistent: it will see its _own_
+accesses appear to be correctly ordered, without the need for a memory barrier.
+For instance with the following code:
+
+ X = *A;
+ *A = Y;
+ Z = *A;
+
+assuming no intervention by an external influence, it can be taken that:
+
+ (*) X will hold the old value of *A, and will never happen after the write and
+ thus end up being given the value that was assigned to *A from Y instead;
+ and
+
+ (*) Z will always be given the value in *A that was assigned there from Y, and
+ will never happen before the write, and thus end up with the same value
+ that was in *A initially.
+
+(This is ignoring the fact that the value initially in *A may appear to be the
+same as the value assigned to *A from Y).
+
+
+=================================
+WHERE ARE MEMORY BARRIERS NEEDED?
+=================================
+
+Under normal operation, access reordering is probably not going to be a problem
+as a linear program will still appear to operate correctly. There are,
+however, three circumstances where reordering definitely _could_ be a problem:
+
+
+ACCESSING DEVICES
+-----------------
+
+Many devices can be memory mapped, and so appear to the CPU as if they're just
+memory locations. However, to control the device, the driver has to make the
+right accesses in exactly the right order.
+
+Consider, for example, an ethernet chipset such as the AMD PCnet32. It
+presents to the CPU an "address register" and a bunch of "data registers". The
+way it's accessed is to write the index of the internal register to be accessed
+to the address register, and then read or write the appropriate data register
+to access the chip's internal register, which could - theoretically - be done
+by:
+
+ *ADR = ctl_reg_3;
+ reg = *DATA;
+
+The problem with a clever CPU or a clever compiler is that the write to the
+address register isn't guaranteed to happen before the access to the data
+register, if the CPU or the compiler thinks it is more efficient to defer the
+address write:
+
+ read *DATA, write *ADR
+
+then things will break.
+
+
+In the Linux kernel, however, I/O should be done through the appropriate
+accessor routines - such as inb() or writel() - which know how to make such
+accesses appropriately sequential.
+
+On some systems, I/O writes are not strongly ordered across all CPUs, and so
+locking should be used, and mmiowb() should be issued prior to unlocking the
+critical section.
+
+See Documentation/DocBook/deviceiobook.tmpl for more information.
+
+
+MULTIPROCESSOR INTERACTION
+--------------------------
+
+When there's a system with more than one processor, the CPUs in the system may
+be working on the same set of data at the same time. This can cause
+synchronisation problems, and the usual way of dealing with them is to use
+locks - but locks are quite expensive, and so it may be preferable to operate
+without the use of a lock if at all possible. In such a case accesses that
+affect both CPUs may have to be carefully ordered to prevent error.
+
+Consider the R/W semaphore slow path. In that, a waiting process is queued on
+the semaphore, as noted by it having a record on its stack linked to the
+semaphore's list:
+
+ struct rw_semaphore {
+ ...
+ struct list_head waiters;
+ };
+
+ struct rwsem_waiter {
+ struct list_head list;
+ struct task_struct *task;
+ };
+
+To wake up the waiter, the up_read() or up_write() functions have to read the
+pointer from this record to know as to where the next waiter record is, clear
+the task pointer, call wake_up_process() on the task, and release the reference
+held on the waiter's task struct:
+
+ READ waiter->list.next;
+ READ waiter->task;
+ WRITE waiter->task;
+ CALL wakeup
+ RELEASE task
+
+If any of these steps occur out of order, then the whole thing may fail.
+
+Note that the waiter does not get the semaphore lock again - it just waits for
+its task pointer to be cleared. Since the record is on its stack, this means
+that if the task pointer is cleared _before_ the next pointer in the list is
+read, another CPU might start processing the waiter and it might clobber its
+stack before up*() functions have a chance to read the next pointer.
+
+ CPU 0 CPU 1
+ =============================== ===============================
+ down_xxx()
+ Queue waiter
+ Sleep
+ up_yyy()
+ READ waiter->task;
+ WRITE waiter->task;
+ <preempt>
+ Resume processing
+ down_xxx() returns
+ call foo()
+ foo() clobbers *waiter
+ </preempt>
+ READ waiter->list.next;
+ --- OOPS ---
+
+This could be dealt with using a spinlock, but then the down_xxx() function has
+to get the spinlock again after it's been woken up, which is a waste of
+resources.
+
+The way to deal with this is to insert an SMP memory barrier:
+
+ READ waiter->list.next;
+ READ waiter->task;
+ smp_mb();
+ WRITE waiter->task;
+ CALL wakeup
+ RELEASE task
+
+In this case, the barrier makes a guarantee that all memory accesses before the
+barrier will appear to happen before all the memory accesses after the barrier
+with respect to the other CPUs on the system. It does _not_ guarantee that all
+the memory accesses before the barrier will be complete by the time the barrier
+itself is complete.
+
+SMP memory barriers are normally nothing more than compiler barriers on a
+kernel compiled for a UP system because the CPU orders overlapping accesses
+with respect to itself, and so CPU barriers aren't needed.
+
+
+INTERRUPTS
+----------
+
+A driver may be interrupted by its own interrupt service routine, and thus they
+may interfere with each other's attempts to control or access the device.
+
+This may be alleviated - at least in part - by disabling interrupts (a form of
+locking), such that the critical operations are all contained within the
+interrupt-disabled section in the driver. Whilst the driver's interrupt
+routine is executing, the driver's core may not run on the same CPU, and its
+interrupt is not permitted to happen again until the current interrupt has been
+handled, thus the interrupt handler does not need to lock against that.
+
+However, consider a driver was talking to an ethernet card that sports an
+address register and a data register. If that driver's core is talks to the
+card under interrupt-disablement and then the driver's interrupt handler is
+invoked:
+
+ DISABLE IRQ
+ writew(ADDR, ctl_reg_3);
+ writew(DATA, y);
+ ENABLE IRQ
+ <interrupt>
+ writew(ADDR, ctl_reg_4);
+ q = readw(DATA);
+ </interrupt>
+
+If ordering rules are sufficiently relaxed, the write to the data register
+might happen after the second write to the address register.
+
+
+It must be assumed that accesses done inside an interrupt disabled section may
+leak outside of it and may interleave with accesses performed in an interrupt
+and vice versa unless implicit or explicit barriers are used.
+
+Normally this won't be a problem because the I/O accesses done inside such
+sections will include synchronous read operations on strictly ordered I/O
+registers that form implicit I/O barriers. If this isn't sufficient then an
+mmiowb() may need to be used explicitly.
+
+
+A similar situation may occur between an interrupt routine and two routines
+running on separate CPUs that communicate with each other. If such a case is
+likely, then interrupt-disabling locks should be used to guarantee ordering.
+
+
+=================================
+EXPLICIT KERNEL COMPILER BARRIERS
+=================================
+
+The Linux kernel has an explicit compiler barrier function that prevents the
+compiler from moving the memory accesses either side of it to the other side:
+
+ barrier();
+
+This has no direct effect on the CPU, which may then reorder things however it
+wishes.
+
+
+In addition, accesses to "volatile" memory locations and volatile asm
+statements act as implicit compiler barriers. Note, however, that the use of
+volatile has two negative consequences:
+
+ (1) it causes the generation of poorer code, and
+
+ (2) it can affect serialisation of events in code distant from the declaration
+ (consider a structure defined in a header file that has a volatile member
+ being accessed by the code in a source file).
+
+The Linux coding style therefore strongly favours the use of explicit barriers
+except in small and specific cases. In general, volatile should be avoided.
+
+
+===============================
+EXPLICIT KERNEL MEMORY BARRIERS
+===============================
+
+The Linux kernel has six basic CPU memory barriers:
+
+ MANDATORY SMP CONDITIONAL
+ =============== ===============
+ GENERAL mb() smp_mb()
+ READ rmb() smp_rmb()
+ WRITE wmb() smp_wmb()
+
+General memory barriers give a guarantee that all memory accesses specified
+before the barrier will appear to happen before all memory accesses specified
+after the barrier with respect to the other components of the system.
+
+Read and write memory barriers give similar guarantees, but only for memory
+reads versus memory reads and memory writes versus memory writes respectively.
+
+All memory barriers imply compiler barriers.
+
+SMP memory barriers are only compiler barriers on uniprocessor compiled systems
+because it is assumed that a CPU will be apparently self-consistent, and will
+order overlapping accesses correctly with respect to itself.
+
+There is no guarantee that any of the memory accesses specified before a memory
+barrier will be complete by the completion of a memory barrier; the barrier can
+be considered to draw a line in that CPU's access queue that accesses of the
+appropriate type may not cross.
+
+There is no guarantee that issuing a memory barrier on one CPU will have any
+direct effect on another CPU or any other hardware in the system. The indirect
+effect will be the order in which the second CPU sees the first CPU's accesses
+occur.
+
+There is no guarantee that some intervening piece of off-the-CPU hardware[*]
+will not reorder the memory accesses. CPU cache coherency mechanisms should
+propegate the indirect effects of a memory barrier between CPUs.
+
+ [*] For information on bus mastering DMA and coherency please read:
+
+ Documentation/pci.txt
+ Documentation/DMA-mapping.txt
+ Documentation/DMA-API.txt
+
+Note that these are the _minimum_ guarantees. Different architectures may give
+more substantial guarantees, but they may not be relied upon outside of arch
+specific code.
+
+
+There are some more advanced barrier functions:
+
+ (*) set_mb(var, value)
+ (*) set_wmb(var, value)
+
+ These assign the value to the variable and then insert at least a write
+ barrier after it, depending on the function. They aren't guaranteed to
+ insert anything more than a compiler barrier in a UP compilation.
+
+
+===============================
+IMPLICIT KERNEL MEMORY BARRIERS
+===============================
+
+Some of the other functions in the linux kernel imply memory barriers, amongst
+which are locking and scheduling functions.
+
+This specification is a _minimum_ guarantee; any particular architecture may
+provide more substantial guarantees, but these may not be relied upon outside
+of arch specific code.
+
+
+LOCKING FUNCTIONS
+-----------------
+
+All the following locking functions imply barriers:
+
+ (*) spin locks
+ (*) R/W spin locks
+ (*) mutexes
+ (*) semaphores
+ (*) R/W semaphores
+
+In all cases there are variants on a LOCK operation and an UNLOCK operation.
+
+ (*) LOCK operation implication:
+
+ Memory accesses issued after the LOCK will be completed after the LOCK
+ accesses have completed.
+
+ Memory accesses issued before the LOCK may be completed after the LOCK
+ accesses have completed.
+
+ (*) UNLOCK operation implication:
+
+ Memory accesses issued before the UNLOCK will be completed before the
+ UNLOCK accesses have completed.
+
+ Memory accesses issued after the UNLOCK may be completed before the UNLOCK
+ accesses have completed.
+
+ (*) LOCK vs UNLOCK implication:
+
+ The LOCK accesses will be completed before the UNLOCK accesses.
+
+ Therefore an UNLOCK followed by a LOCK is equivalent to a full barrier,
+ but a LOCK followed by an UNLOCK is not.
+
+Locks and semaphores may not provide any guarantee of ordering on UP compiled
+systems, and so can't be counted on in such a situation to actually do anything
+at all, especially with respect to I/O accesses, unless combined with interrupt
+disabling operations.
+
+See also the section on "Inter-CPU locking barrier effects".
+
+
+As an example, consider the following:
+
+ *A = a;
+ *B = b;
+ LOCK
+ *C = c;
+ *D = d;
+ UNLOCK
+ *E = e;
+ *F = f;
+
+The following sequence of events is acceptable:
+
+ LOCK, {*F,*A}, *E, {*C,*D}, *B, UNLOCK
+
+But none of the following are:
+
+ {*F,*A}, *B, LOCK, *C, *D, UNLOCK, *E
+ *A, *B, *C, LOCK, *D, UNLOCK, *E, *F
+ *A, *B, LOCK, *C, UNLOCK, *D, *E, *F
+ *B, LOCK, *C, *D, UNLOCK, {*F,*A}, *E
+
+
+INTERRUPT DISABLING FUNCTIONS
+-----------------------------
+
+Functions that disable interrupts (LOCK equivalent) and enable interrupts
+(UNLOCK equivalent) will act as compiler barriers only. So if memory or I/O
+barriers are required in such a situation, they must be provided from some
+other means.
+
+
+MISCELLANEOUS FUNCTIONS
+-----------------------
+
+Other functions that imply barriers:
+
+ (*) schedule() and similar imply full memory barriers.
+
+
+=================================
+INTER-CPU LOCKING BARRIER EFFECTS
+=================================
+
+On SMP systems locking primitives give a more substantial form of barrier: one
+that does affect memory access ordering on other CPUs, within the context of
+conflict on any particular lock.
+
+
+LOCKS VS MEMORY ACCESSES
+------------------------
+
+Consider the following: the system has a pair of spinlocks (N) and (Q), and
+three CPUs; then should the following sequence of events occur:
+
+ CPU 1 CPU 2
+ =============================== ===============================
+ *A = a; *E = e;
+ LOCK M LOCK Q
+ *B = b; *F = f;
+ *C = c; *G = g;
+ UNLOCK M UNLOCK Q
+ *D = d; *H = h;
+
+Then there is no guarantee as to what order CPU #3 will see the accesses to *A
+through *H occur in, other than the constraints imposed by the separate locks
+on the separate CPUs. It might, for example, see:
+
+ *E, LOCK M, LOCK Q, *G, *C, *F, *A, *B, UNLOCK Q, *D, *H, UNLOCK M
+
+But it won't see any of:
+
+ *B, *C or *D preceding LOCK M
+ *A, *B or *C following UNLOCK M
+ *F, *G or *H preceding LOCK Q
+ *E, *F or *G following UNLOCK Q
+
+
+However, if the following occurs:
+
+ CPU 1 CPU 2
+ =============================== ===============================
+ *A = a;
+ LOCK M [1]
+ *B = b;
+ *C = c;
+ UNLOCK M [1]
+ *D = d; *E = e;
+ LOCK M [2]
+ *F = f;
+ *G = g;
+ UNLOCK M [2]
+ *H = h;
+
+CPU #3 might see:
+
+ *E, LOCK M [1], *C, *B, *A, UNLOCK M [1],
+ LOCK M [2], *H, *F, *G, UNLOCK M [2], *D
+
+But assuming CPU #1 gets the lock first, it won't see any of:
+
+ *B, *C, *D, *F, *G or *H preceding LOCK M [1]
+ *A, *B or *C following UNLOCK M [1]
+ *F, *G or *H preceding LOCK M [2]
+ *A, *B, *C, *E, *F or *G following UNLOCK M [2]
+
+
+LOCKS VS I/O ACCESSES
+---------------------
+
+Under certain circumstances (such as NUMA), I/O accesses within two spinlocked
+sections on two different CPUs may be seen as interleaved by the PCI bridge.
+
+For example:
+
+ CPU 1 CPU 2
+ =============================== ===============================
+ spin_lock(Q)
+ writel(0, ADDR)
+ writel(1, DATA);
+ spin_unlock(Q);
+ spin_lock(Q);
+ writel(4, ADDR);
+ writel(5, DATA);
+ spin_unlock(Q);
+
+may be seen by the PCI bridge as follows:
+
+ WRITE *ADDR = 0, WRITE *ADDR = 4, WRITE *DATA = 1, WRITE *DATA = 5
+
+which would probably break.
+
+What is necessary here is to insert an mmiowb() before dropping the spinlock,
+for example:
+
+ CPU 1 CPU 2
+ =============================== ===============================
+ spin_lock(Q)
+ writel(0, ADDR)
+ writel(1, DATA);
+ mmiowb();
+ spin_unlock(Q);
+ spin_lock(Q);
+ writel(4, ADDR);
+ writel(5, DATA);
+ mmiowb();
+ spin_unlock(Q);
+
+this will ensure that the two writes issued on CPU #1 appear at the PCI bridge
+before either of the writes issued on CPU #2.
+
+
+Furthermore, following a write by a read to the same device is okay, because
+the read forces the write to complete before the read is performed:
+
+ CPU 1 CPU 2
+ =============================== ===============================
+ spin_lock(Q)
+ writel(0, ADDR)
+ a = readl(DATA);
+ spin_unlock(Q);
+ spin_lock(Q);
+ writel(4, ADDR);
+ b = readl(DATA);
+ spin_unlock(Q);
+
+
+See Documentation/DocBook/deviceiobook.tmpl for more information.
+
+
+==========================
+KERNEL I/O BARRIER EFFECTS
+==========================
+
+When accessing I/O memory, drivers should use the appropriate accessor
+functions:
+
+ (*) inX(), outX():
+
+ These are intended to talk to I/O space rather than memory space, but
+ that's primarily a CPU-specific concept. The i386 and x86_64 processors do
+ indeed have special I/O space access cycles and instructions, but many
+ CPUs don't have such a concept.
+
+ The PCI bus, amongst others, defines an I/O space concept - which on such
+ CPUs as i386 and x86_64 cpus readily maps to the CPU's concept of I/O
+ space. However, it may also mapped as a virtual I/O space in the CPU's
+ memory map, particularly on those CPUs that don't support alternate
+ I/O spaces.
+
+ Accesses to this space may be fully synchronous (as on i386), but
+ intermediary bridges (such as the PCI host bridge) may not fully honour
+ that.
+
+ They are guaranteed to be fully ordered with respect to each other.
+
+ They are not guaranteed to be fully ordered with respect to other types of
+ memory and I/O operation.
+
+ (*) readX(), writeX():
+
+ Whether these are guaranteed to be fully ordered and uncombined with
+ respect to each other on the issuing CPU depends on the characteristics
+ defined for the memory window through which they're accessing. On later
+ i386 architecture machines, for example, this is controlled by way of the
+ MTRR registers.
+
+ Ordinarily, these will be guaranteed to be fully ordered and uncombined,,
+ provided they're not accessing a prefetchable device.
+
+ However, intermediary hardware (such as a PCI bridge) may indulge in
+ deferral if it so wishes; to flush a write, a read from the same location
+ is preferred[*], but a read from the same device or from configuration
+ space should suffice for PCI.
+
+ [*] NOTE! attempting to read from the same location as was written to may
+ cause a malfunction - consider the 16550 Rx/Tx serial registers for
+ example.
+
+ Used with prefetchable I/O memory, an mmiowb() barrier may be required to
+ force writes to be ordered.
+
+ Please refer to the PCI specification for more information on interactions
+ between PCI transactions.
+
+ (*) readX_relaxed()
+
+ These are similar to readX(), but are not guaranteed to be ordered in any
+ way. Be aware that there is no I/O read barrier available.
+
+ (*) ioreadX(), iowriteX()
+
+ These will perform as appropriate for the type of access they're actually
+ doing, be it inX()/outX() or readX()/writeX().
+
+
+==========
+REFERENCES
+==========
+
+AMD64 Architecture Programmer's Manual Volume 2: System Programming
+ Chapter 7.1: Memory-Access Ordering
+ Chapter 7.4: Buffering and Combining Memory Writes
+
+IA-32 Intel Architecture Software Developer's Manual, Volume 3:
+System Programming Guide
+ Chapter 7.1: Locked Atomic Operations
+ Chapter 7.2: Memory Ordering
+ Chapter 7.4: Serializing Instructions
+
+The SPARC Architecture Manual, Version 9
+ Chapter 8: Memory Models
+ Appendix D: Formal Specification of the Memory Models
+ Appendix J: Programming with the Memory Models
+
+UltraSPARC Programmer Reference Manual
+ Chapter 5: Memory Accesses and Cacheability
+ Chapter 15: Sparc-V9 Memory Models
+
+UltraSPARC III Cu User's Manual
+ Chapter 9: Memory Models
+
+UltraSPARC IIIi Processor User's Manual
+ Chapter 8: Memory Models
+
+UltraSPARC Architecture 2005
+ Chapter 9: Memory
+ Appendix D: Formal Specifications of the Memory Models
+
+UltraSPARC T1 Supplment to the UltraSPARC Architecture 2005
+ Chapter 8: Memory Models
+ Appendix F: Caches and Cache Coherency
+
+Solaris Internals, Core Kernel Architecture, p63-68:
+ Chapter 3.3: Hardware Considerations for Locks and
+ Synchronization
+
+Unix Systems for Modern Architectures, Symmetric Multiprocessing and Caching
+for Kernel Programmers:
+ Chapter 13: Other Memory Models
+
+Intel Itanium Architecture Software Developer's Manual: Volume 1:
+ Section 2.6: Speculation
+ Section 4.4: Memory Access
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
