On Tuesday, 7. March 2006 06:43, Andrew Morton wrote:
> Dominik Karall <[email protected]> wrote:
> > On Friday, 3. March 2006 13:56, Andrew Morton wrote:
> > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.16-rc
> > >5/2. 6.16-rc5-mm2/
> >
> > hi,
> > I don't know why, but it seems that the kernel doesn't use the correct
> > BIOS time. I set it to the 23:30 and after booting I got ~01:00 (next
> > day).
>
> Is that new behaviour? What's the most recent -mm kernel which that
> machine ran?
>
> The full dmesg output might tell us something.
I bootet 2.6.16-rc5 now, but the bug is still present. I set BIOS time to
15:07 and after booting linux showed 17:35.
Here is the dmesg output:
Linux version 2.6.16-rc5 (root@localhost) (gcc-Version 4.1.0 (Gentoo 4.1.0))
#6 SMP PREEMPT Tue Mar 7 15:04:35 CET 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff30000 (usable)
BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa8b0
ACPI: XSDT (v001 A M I OEMXSDT 0x08000403 MSFT 0x00000097) @
0x000000003ff30100
ACPI: FADT (v003 A M I OEMFACP 0x08000403 MSFT 0x00000097) @
0x000000003ff30290
ACPI: MADT (v001 A M I OEMAPIC 0x08000403 MSFT 0x00000097) @
0x000000003ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x08000403 MSFT 0x00000097) @
0x000000003ff40040
ACPI: DSDT (v001 A0058 A0058002 0x00000002 MSFT 0x0100000d) @
0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000003ff30000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000003ff30000
On node 0 totalpages: 258249
DMA zone: 3934 pages, LIFO batch:0
DMA32 zone: 254315 pages, LIFO batch:31
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bff80000)
Checking aperture...
CPU 0: aperture @ e0000000 size 256 MB
Built 1 zonelists
Kernel command line:
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2460.198 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 1010564k/1047744k available (3289k kernel code, 36792k reserved, 1308k
data, 220k init)
Calibrating delay using timer specific routine.. 4928.48 BogoMIPS
(lpj=2464243)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(1) -> Node 0 -> Core 0
Using local APIC timer interrupts.
result 12813545
Detected 12.813 MHz APIC timer.
Brought up 1 CPUs
testing NMI watchdog ... OK.
migration_cost=0
DMI 2.3 present.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 256M @ 0xe0000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: fcd00000-fd2fffff
PREFETCH window: 9fb00000-dfafffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
Using specific hotkey driver
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
loop: loaded (max 8 devices)
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 169
sk98lin: Asus mainboard with buggy VPD? Correcting data.
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
PPP generic driver version 2.4.2
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 177
bttv0: Bt878 (rev 17) at 0000:00:0d.0, irq: 177, latency: 128, mmio:
0xdfe00000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00fffffb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
tveeprom 0-0050: Hauppauge model 38074, rev B521, serial# 5099850
tveeprom 0-0050: tuner model is Philips FM1216 (idx 21, type 5)
tveeprom 0-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 0-0050: audio processor is None (idx 0)
tveeprom 0-0050: has radio
bttv0: Hauppauge eeprom indicates model#38074
bttv0: using tuner=5
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
input: i2c IR (Hauppauge) as /class/input/input0
ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [bt878 #0 [sw]]
tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner 0-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 185
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 9
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG SP1604N, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ATAPI DVD DD 2X16X4X16, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63,
UDMA(133)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 185
PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
sata_via 0000:00:0f.0: routed to hard irq line 9
ata1: SATA max UDMA/133 cmd 0xE800 ctl 0xE402 bmdma 0xD400 irq 185
ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xD802 bmdma 0xD408 irq 185
ata1: SATA link down (SStatus 0)
scsi0 : sata_via
ata2: SATA link down (SStatus 0)
scsi1 : sata_via
ieee1394: Initialized config rom entry `ip1394'
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 193
PCI: Via IRQ fixup for 0000:00:07.0, from 11 to 1
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[193] MMIO=[fd800000-fd8007ff]
Max Packet=[2048] IR/IT contexts=[4/8]
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
input: PC Speaker as /class/input/input2
i2c /dev entries driver
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [email protected]
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04
08:57:20 2006 UTC).
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 201
PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 9
PCI: Setting latency timer of device 0000:00:11.5 to 64
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
ALSA device list:
#0: VIA 8237 with AD1980 at 0xc800, irq 201
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP bic registered
TCP westwood registered
TCP htcp registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.0)
powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xe (1200 mV)
powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xa (1300 mV)
powernow-k8: 3 : fid 0xe (2200 MHz), vid 0x6 (1400 mV)
powernow-k8: 4 : fid 0x10 (2400 MHz), vid 0x2 (1500 mV)
cpu_init done, current fid 0x10, vid 0x0
powernow-k8: ph2 null fid transition 0x10
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
input: ImPS/2 Generic Wheel Mouse as /class/input/input3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180000ad032e]
EXT3-fs: hda1: orphan cleanup on readonly fs
kjournald starting. Commit interval 5 seconds
ext3_orphan_cleanup: deleting unreferenced inode 1971295
ext3_orphan_cleanup: deleting unreferenced inode 1971248
ext3_orphan_cleanup: deleting unreferenced inode 1971040
EXT3-fs: hda1: 3 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 220k freed
Adding 996020k swap on /dev/hda3. Priority:-1 extents:1 across:996020k
EXT3 FS on hda1, internal journal
ACPI: PCI Interrupt 0000:00:0d.1[A] -> GSI 18 (level, low) -> IRQ 177
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 209
eth2: Identified chip type is 'RTL8169s/8110s'.
eth2: RTL8169 at 0xffffc20000246000, 00:0c:f6:04:87:c0, IRQ 209
USB Universal Host Controller Interface driver v2.3
GSI 22 sharing vector 0xD9 and IRQ 22
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 217
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 217, io base 0x0000b400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 217
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 9
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 217, io base 0x0000b800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 217
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 9
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 217, io base 0x0000c000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 217
PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 9
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 217, io base 0x0000c400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0
proto 2 vid 0x03F0 pid 0x7004
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 217
PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 9
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 217, io mem 0xfdf00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hub 1-2:1.0: hub_port_status failed (err = -71)
hub 1-2:1.0: connect-debounce failed, port 1 disabled
hub 1-2:1.0: cannot disable port 1 (err = -71)
hub 1-2:1.0: hub_port_status failed (err = -71)
hub 1-2:1.0: hub_port_status failed (err = -71)
hub 1-2:1.0: hub_port_status failed (err = -71)
usb 2-1: USB disconnect, address 2
drivers/usb/class/usblp.c: usblp0: removed
usb 5-2: new high speed USB device using ehci_hcd and address 2
usb 5-2: configuration #1 chosen from 1 choice
hub 5-2:1.0: USB hub found
hub 5-2:1.0: 4 ports detected
usb 1-2: USB disconnect, address 2
usb 5-2.1: new high speed USB device using ehci_hcd and address 4
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
usb 5-2.1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0
proto 2 vid 0x03F0 pid 0x7004
Vendor: Generic Model: 223 U HS-CF Rev: 1.95
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:0: Attached scsi removable disk sda
sd 2:0:0:0: Attached scsi generic sg0 type 0
Vendor: Generic Model: 223 U HS-MS Rev: 1.95
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:1: Attached scsi removable disk sdb
sd 2:0:0:1: Attached scsi generic sg1 type 0
usb-storage: device scan complete
ReiserFS: dm-0: found reiserfs format "3.6" with standard journal
ReiserFS: dm-0: using ordered data mode
ReiserFS: dm-0: journal params: device dm-0, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-0: checking transaction log (dm-0)
ReiserFS: dm-0: Using r5 hash to sort names
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
irq moderation: disabled
scatter-gather: disabled
tx-checksum: disabled
rx-checksum: disabled
PPP BSD Compression module registered
PPP Deflate Compression module registered
usb 5-2.2: new high speed USB device using ehci_hcd and address 5
usb 5-2.2: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Vendor: ST325082 Model: 3A Rev: 3.02
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
sdc: Write Protect is off
sdc: Mode Sense: 03 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
sdc: Write Protect is off
sdc: Mode Sense: 03 00 00 00
sdc: assuming drive cache: write through
sdc:<6>Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
sdc1 sdc2
sd 3:0:0:0: Attached scsi disk sdc
sd 3:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 193
[drm] Initialized radeon 1.22.0 20051229 on minor 0
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: X tried to set rate=x12. Setting to AGP3 x8 mode.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[drm] Loading R300 Microcode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: X tried to set rate=x12. Setting to AGP3 x8 mode.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[drm] Loading R300 Microcode
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
