Hello,
I will follow the
http://www.kernel.org/pub/linux/docs/lkml/reporting-bugs.html to
describe the bug:
### [1.] One line summary of the problem:
Four PCI TV tuners based on bt878 chip in one PC crashed.
### [2.] Full description of the problem/report:
I'm runnig four XAWTVs on one screen. Screen is splited by XAWTV to two
columns and two rows [6.]. If I'm clicking randomly everywhere on all
XAWTVs with right and left mouse button, the picture (PC) freeze.
Sometimes it frozen hard (doesn't works Alt+SysRq), sometimes soft (does
works Alt-SysRq).
### [3.] Keywords (i.e., modules, networking, kernel):
kernel, modules
### [4.] Kernel version (from /proc/version):
Linux version 2.6.16-rc5 (root@livecd) (gcc version 3.4.4 (Gentoo
3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #2 Mon Mar 6 15:59:18 CET 2006
### [5.] Output of Oops.. message (if applicable) with symbolic
information resolved:
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv2: OCERR @ 1ef89014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv2: OCERR @ 1ef89014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv2: OCERR @ 1ef89000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv2: OCERR @ 1ef89000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:11 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv2: OCERR @ 1ef89000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv2: OCERR @ 1ef89014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:12 watch4tv bttv3: timeout: drop=0 irq=228/1180,
risc=18ad4fdc, bits: HSYNC OFLOW
Mar 6 16:03:12 watch4tv bttv3: reset, reinitialize
Mar 6 16:03:12 watch4tv bttv3: PLL: 28636363 => 35468950 . ok
Mar 6 16:03:12 watch4tv bttv2: timeout: drop=0 irq=292/292,
risc=18b9d860, bits: HSYNC OFLOW
Mar 6 16:03:12 watch4tv bttv2: reset, reinitialize
Mar 6 16:03:12 watch4tv bttv2: PLL: 28636363 => 35468950 . ok
Mar 6 16:03:12 watch4tv bttv3: OCERR @ 1efbf01c,bits: VSYNC HSYNC OFLOW
OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf000,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf000,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf000,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: OCERR @ 1efbf014,bits: VSYNC HSYNC OFLOW
FDSR OCERR*
Mar 6 16:03:13 watch4tv bttv3: timeout: drop=0 irq=244/1207,
risc=18ba701c, bits: VSYNC HSYNC OFLOW
Mar 6 16:03:13 watch4tv bttv3: reset, reinitialize
Mar 6 16:03:13 watch4tv bttv3: PLL: 28636363 => 35468950 . ok
Mar 6 16:03:23 watch4tv Unable to handle kernel paging request at
virtual address 200001d4
Mar 6 16:03:23 watch4tv printing eip:
Mar 6 16:03:23 watch4tv c0156ac7
Mar 6 16:03:23 watch4tv *pde = 00000000
Mar 6 16:03:23 watch4tv Oops: 0000 [#1]
Mar 6 16:03:23 watch4tv Modules linked in: i915 drm ohci_hcd tuner
tvaudio bttv video_buf compat_ioctl32 i2c_algo_bit v4l2_common btcx_risc
ir_common tveeprom i2c_core videodev ehci_hcd usb_storage uhci_hcd
snd_pcm_oss snd_mixer_oss snd_seq_oss snd_seq_midi_event snd_seq
snd_seq_device snd_bt87x snd_hda_intel snd_hda_codec snd_pcm snd_timer
snd soundcore snd_page_alloc usbcore
Mar 6 16:03:23 watch4tv CPU: 0
Mar 6 16:03:23 watch4tv EIP: 0060:[<c0156ac7>] Not tainted VLI
Mar 6 16:03:23 watch4tv EFLAGS: 00013212 (2.6.16-rc5 #2)
Mar 6 16:03:23 watch4tv EIP is at poll_freewait+0x16/0x3c
Mar 6 16:03:23 watch4tv eax: de25fefc ebx: 200001bc ecx: ffffffff
edx: 200001c0
Mar 6 16:03:23 watch4tv esi: da061000 edi: 00008000 ebp: 00000000
esp: de25fea8
Mar 6 16:03:23 watch4tv ds: 007b es: 007b ss: 0068
Mar 6 16:03:23 watch4tv Process X (pid: 8946, threadinfo=de25e000
task=dea45070)
Mar 6 16:03:23 watch4tv Stack: <0>de25ff98 00000000 c0156f1c de25fefc
00000000 00000000 0000783a 00000000
Mar 6 16:03:23 watch4tv 00000000 00000000 0000000f 0000783a de53c104
de53c0e4 de53c0c4 de53c164
Mar 6 16:03:23 watch4tv de53c144 de53c124 0000000f 00000000 0000000f
c0156aed da061000 00000000
Mar 6 16:03:23 watch4tv Call Trace:
Mar 6 16:03:23 watch4tv [<c0156f1c>] do_select+0x2cc/0x2d7
Mar 6 16:03:23 watch4tv [<c0156aed>] __pollwait+0x0/0x9a
Mar 6 16:03:23 watch4tv [<c0157141>] core_sys_select+0x202/0x2b7
Mar 6 16:03:23 watch4tv [<c0157293>] sys_select+0x9d/0x161
Mar 6 16:03:23 watch4tv [<c0149137>] sys_writev+0x3b/0x96
Mar 6 16:03:23 watch4tv [<c010292b>] sysenter_past_esp+0x54/0x75
Mar 6 16:03:23 watch4tv Code: c7 00 ed 6a 15 c0 c7 40 08 00 00 00 00 c7
40 04 00 00 00 00 c3 56 53 8b 44 24 0c 8b 70 04 85 f6 74 2c 8b 5e 04 83
eb 1c 8d 53 04 <8b> 43 18 e8 24 e7 fc ff 8b 03 e8 d0 2a ff ff 8d 46 08
39 c3 77
Mar 6 16:03:23 watch4tv <6>bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf000,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:23 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: OCERR @ 1efbf014,bits: HSYNC OFLOW OCERR*
Mar 6 16:03:24 watch4tv bttv3: timeout: drop=0 irq=357/1364,
risc=1efbf01c, bits: HSYNC OFLOW
Mar 6 16:03:27 watch4tv bttv3: reset, reinitialize
Mar 6 16:03:27 watch4tv bttv3: PLL: 28636363 => 35468950 . ok
Mar 6 16:03:54 watch4tv SysRq : Emergency Remount R/O
### [6.] A small shell script or example program which triggers the problem:
#!/bin/bash
export LC_ALL="en_US.ISO-8859-1"
export DISPLAY=:0
X -bpp 16 -auth /var/run/xauth/A:0-DieZbc vt7 &
xhost +
sleep 2
v4l-conf -c /dev/video0 -d :0 &
v4l-conf -c /dev/video1 -d :0 &
v4l-conf -c /dev/video2 -d :0 &
v4l-conf -c /dev/video3 -d :0 &
xawtv -c /dev/video0 -geometry 639x511+0+0 -display :0 "CERN site SE17" &
xawtv -c /dev/video1 -geometry 639x511+640+0 -display :0 "CERN site SE18" &
xawtv -c /dev/video2 -geometry 639x511+0+512 -display :0 "CERN site SE19" &
xawtv -c /dev/video3 -geometry 639x511+640+512 -display :0 "CERN site
SE20" &
xset -display :0 -dpms &
xset -display :0 s noblank &
xset -display :0 s noexpose &
xset -display :0 s off &
xset -display :0 s 0 0 &
### [7.] Environment:
### [7.1.] Software (add the output of the ver_linux script here):
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux watch4tv 2.6.16-rc5 #2 Mon Mar 6 15:59:18 CET 2006 i686 Intel(R)
Celeron(R) CPU 2.80GHz GenuineIntel GNU/Linux
Gnu C 3.4.4
Gnu make 3.80
binutils 2.16.1
util-linux 2.12r
mount 2.12r
module-init-tools 3.2.1
e2fsprogs 1.38
reiserfsprogs 3.6.19
reiser4progs line
Linux C Library 2.3.5
Dynamic linker (ldd) 2.3.5
Procps 3.2.5
Net-tools 1.60
Kbd 1.12
Sh-utils 5.2.1
udev 079
Modules Loaded nls_cp850 i915 drm ohci_hcd tuner tvaudio bttv
video_buf compat_ioctl32 i2c_algo_bit v4l2_common btcx_risc ir_common
tveeprom i2c_core videodev ehci_hcd usb_storage uhci_hcd snd_pcm_oss
snd_mixer_oss snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device
snd_bt87x snd_hda_intel snd_hda_codec snd_pcm snd_timer snd soundcore
snd_page_alloc usbcore
### [7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Celeron(R) CPU 2.80GHz
stepping : 1
cpu MHz : 2800.604
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx
constant_tsc pni monitor ds_cpl tm2 cid xtpr
bogomips : 5611.80
### [7.3.] Module information (from /proc/modules):
nls_cp850 4736 1 - Live 0xe0505000
i915 15744 1 - Live 0xe04d9000
drm 53652 2 i915, Live 0xe04e5000
ohci_hcd 16132 0 - Live 0xe048a000
tuner 44460 0 - Live 0xe048f000
tvaudio 19996 0 - Live 0xe0475000
bttv 150900 4 - Live 0xe04a4000
video_buf 15364 1 bttv, Live 0xe047b000
compat_ioctl32 1152 1 bttv, Live 0xe043c000
i2c_algo_bit 7432 1 bttv, Live 0xe0472000
v4l2_common 6528 2 tuner,bttv, Live 0xe0447000
btcx_risc 3720 1 bttv, Live 0xe0078000
ir_common 7812 1 bttv, Live 0xe041e000
tveeprom 12176 1 bttv, Live 0xe046e000
i2c_core 15248 5 tuner,tvaudio,bttv,i2c_algo_bit,tveeprom, Live 0xe0442000
videodev 6656 5 bttv, Live 0xe0421000
ehci_hcd 23560 0 - Live 0xe0467000
usb_storage 29316 1 - Live 0xe045e000
uhci_hcd 25872 0 - Live 0xe0456000
snd_pcm_oss 40992 0 - Live 0xe044a000
snd_mixer_oss 14080 1 snd_pcm_oss, Live 0xe0424000
snd_seq_oss 26112 0 - Live 0xe0434000
snd_seq_midi_event 5504 1 snd_seq_oss, Live 0xe041b000
snd_seq 40016 4 snd_seq_oss,snd_seq_midi_event, Live 0xe0429000
snd_seq_device 6284 2 snd_seq_oss,snd_seq, Live 0xe00fb000
snd_bt87x 10824 0 - Live 0xe004d000
snd_hda_intel 12688 0 - Live 0xe006f000
snd_hda_codec 111616 1 snd_hda_intel, Live 0xe0317000
snd_pcm 66952 4 snd_pcm_oss,snd_bt87x,snd_hda_intel,snd_hda_codec, Live
0xe0305000
snd_timer 17540 2 snd_seq,snd_pcm, Live 0xe005e000
snd 39140 10
snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_bt87x,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer,
Live 0xe0064000
soundcore 6624 1 snd, Live 0xe0054000
snd_page_alloc 7688 3 snd_bt87x,snd_hda_intel,snd_pcm, Live 0xe0051000
usbcore 97668 5 ohci_hcd,ehci_hcd,usb_storage,uhci_hcd, Live 0xe00c1000
### [7.4.] Loaded driver and hardware information (/proc/ioports,
/proc/iomem):
## /proc/ioports:
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0400-0403 : PM1a_EVT_BLK
0404-0405 : PM1a_CNT_BLK
0408-040b : PM_TMR
0410-0415 : ACPI CPU throttle
0420-0420 : PM2_CNT_BLK
0428-042f : GPE0_BLK
0500-053f : pnp 00:0c
0680-06ff : pnp 00:0c
c400-c41f : 0000:00:1f.3
c800-c81f : 0000:00:1d.0
c800-c81f : uhci_hcd
cc00-cc1f : 0000:00:1d.1
cc00-cc1f : uhci_hcd
d000-d01f : 0000:00:1d.2
d000-d01f : uhci_hcd
d400-d41f : 0000:00:1d.3
d400-d41f : uhci_hcd
d800-d80f : 0000:00:1f.2
d800-d80f : libata
dc00-dc03 : 0000:00:1f.2
dc00-dc03 : libata
e000-e007 : 0000:00:1f.2
e000-e007 : libata
e400-e403 : 0000:00:1f.2
e400-e403 : libata
e800-e807 : 0000:00:1f.2
e800-e807 : libata
ec00-ec07 : 0000:00:02.0
ffa0-ffaf : 0000:00:1f.1
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
## /proc/iomem:
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-1f72fbff : System RAM
00100000-002cb992 : Kernel code
002cb993-00380453 : Kernel data
1f72fc00-1f72ffff : ACPI Non-volatile Storage
1f730000-1f73ffff : ACPI Tables
1f740000-1f7effff : ACPI Non-volatile Storage
1f7f0000-1f7fffff : reserved
c0000000-cfffffff : 0000:00:02.0
d0000000-d00fffff : PCI Bus #01
d0100000-d01fffff : PCI Bus #02
d0200000-d02fffff : PCI Bus #03
d0300000-d03fffff : PCI Bus #04
d0400000-d04fffff : PCI Bus #05
d0500000-d05fffff : PCI Bus #06
d0500000-d0500fff : 0000:06:00.1
d0500000-d0500fff : Bt87x audio
d0501000-d0501fff : 0000:06:00.0
d0501000-d0501fff : bttv0
d0502000-d0502fff : 0000:06:01.1
d0502000-d0502fff : Bt87x audio
d0503000-d0503fff : 0000:06:01.0
d0503000-d0503fff : bttv1
d0504000-d0504fff : 0000:06:02.1
d0504000-d0504fff : Bt87x audio
d0505000-d0505fff : 0000:06:02.0
d0505000-d0505fff : bttv2
d0506000-d0506fff : 0000:06:03.1
d0506000-d0506fff : Bt87x audio
d0507000-d0507fff : 0000:06:03.0
d0507000-d0507fff : bttv3
e0000000-efffffff : reserved
fed13000-fed19fff : reserved
fed1c000-fed9ffff : reserved
ff400000-ff4fffff : PCI Bus #01
ff500000-ff5fffff : PCI Bus #02
ff600000-ff6fffff : PCI Bus #03
ff700000-ff7fffff : PCI Bus #04
ff800000-ff8fffff : PCI Bus #05
ff900000-ff9fffff : PCI Bus #06
ffa00000-ffa7ffff : 0000:00:02.0
ffa80000-ffabffff : 0000:00:02.0
ffac0000-ffac3fff : 0000:00:1b.0
ffac0000-ffac3fff : ICH HD audio
ffac4000-ffac43ff : 0000:00:1d.7
ffac4000-ffac43ff : ehci_hcd
[7.5.] PCI information ('lspci -vvv' as root):
00:00.0 Host bridge: Intel Corporation 915G/P/GV/GL/PL/910GL Processor
to I/O Controller (rev 04)
Subsystem: Intel Corporation Unknown device 4156
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge: Intel Corporation 915G/P/GV/GL/PL/910GL PCI Express
Root Port (rev 04) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff400000-ff4fffff
Prefetchable memory behind bridge: d0000000-d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug-
Surpise-
Slot: Number 0, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)
00:02.0 VGA compatible controller: Intel Corporation 82915G/GV/910GL
Express Chipset Family Graphics Controller (rev 04) (prog-if 00 [VGA])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ffa00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at ffa80000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1b.0 Class 0403: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) High Definition Audio Controller (rev 03)
Subsystem: Intel Corporation Unknown device e203
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ffac0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown,
Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff800000-ff8fffff
Prefetchable memory behind bridge: 00000000d0400000-00000000d0400000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 1, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff700000-ff7fffff
Prefetchable memory behind bridge: 00000000d0300000-00000000d0300000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 2, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.2 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 3 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff600000-ff6fffff
Prefetchable memory behind bridge: 00000000d0200000-00000000d0200000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 3, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff500000-ff5fffff
Prefetchable memory behind bridge: 00000000d0100000-00000000d0100000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 4, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 4: I/O ports at c800 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at cc00 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d000 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d400 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ffac4000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d3) (prog-if
01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=128
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: ff900000-ff9fffff
Prefetchable memory behind bridge: 00000000d0500000-00000000d0500000
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00:1f.0 ISA bridge: Intel Corporation 82801FB/FR (ICH6/ICH6R) LPC
Interface Bridge (rev 03)
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]
00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA
Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at e800 [size=8]
Region 1: I/O ports at e400 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at d800 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
SMBus Controller (rev 03)
Subsystem: Intel Corporation Unknown device 4156
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at c400 [size=32]
06:00.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0501000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:00.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0500000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:01.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0503000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:01.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0502000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:02.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0505000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:02.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0504000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:03.0 Multimedia video controller: Brooktree Corporation Bt878 Video
Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0507000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:03.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
(rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0506000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
### [7.6.] SCSI information (from /proc/scsi/scsi):
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: WDC WD800JD-22LS Rev: 06.0
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: Generic Model: USB Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
### [7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you think to be
relevant):
## modprobe.conf:
alias char-major-81 videodev
alias char-major-8-0 bttv
alias char-major-8-1 bttv
alias char-major-8-2 bttv
alias char-major-8-3 bttv
options bttv card=10 tuner=41
### [8] Other notes, patches, fixes, workarounds:
* Mainboard: Intel D945GNT (945 chipset) - I have tryed it also with
Intel D915GAV. All four PCI slots are used for TV tuners. AGP slot is
unused (graphics card is on the board).
# Power supply: Chieftec 400W
# Memory: Kingston 512MB
# HDD: Western Digital SATA 80GB
# TV Tuner: 4x Hauppauge WinTV Express (chip bt878)
* I have tryed vanilla kernel 2.6.15.1 and 2.6.16-rc5 (with / without
PREEMPT, acpi=on / acpi=off).
* I have tryed insmod options from
Documents/video4linux/bttv/Insmod-options.
* I have tryed Xorg 6.9 and Xorg 6.8.2 (with / without DRI support -
Xorg driver i810).
* I have tryed XAWTV 3.94 and XAWTV 3.95.
* I have tryed Gentoo Linux distribution and Scientific Linux CERN 4
(based on RHEL4).
* I have tryed change BIOS options: Plug&Play Enabled/Disabled, PCI IRQ
Auto/Manual.
*** always the same.
If somebody know how to solve it, I will be very appreciative. I have
tryed everything what I know, nothing helps.
Best Regards,
Jiri Tyr
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
