On Thu, 2 Mar 2006, [email protected] wrote:
> Zwane Mwaikambo writes:
> > On Thu, 2 Mar 2006, [email protected] wrote:
> >
> > > This is a dual xeon system with hyper threading enabled, so there should
> > > be 4 cpus
> > >
> > > jm@voyager ~ $ ll /proc/acpi/processor/
> > > total 0
> > > dr-xr-xr-x 2 root root 0 Mar 2 05:01 CPU0
> > > dr-xr-xr-x 2 root root 0 Mar 2 05:01 CPU1
> > > dr-xr-xr-x 2 root root 0 Mar 2 05:01 CPU3
> >
> > Can you try sending dmesg output too?
>
> here it is, but this time all 4 cpus are detected. Later I will try some reboots
> and check if I can reproduce the problem.
Thanks, i'll wait for those results.
>
> Linux version 2.6.16-rc5 (root@voyager) (gcc version 3.4.5 (Gentoo Hardened 3.4.5-r1, ssp-3.4.5-1.0, pie-8.7.9)) #1 SMP PREEMPT Wed Mar 1 02:29:54 UTC 2006
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007ff75000 (usable)
> BIOS-e820: 000000007ff75000 - 000000007ff77000 (ACPI NVS)
> BIOS-e820: 000000007ff77000 - 000000007ff98000 (ACPI data)
> BIOS-e820: 000000007ff98000 - 0000000080000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec90000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
> 1151MB HIGHMEM available.
> 896MB LOWMEM available.
> found SMP MP-table at 000fe710
> On node 0 totalpages: 524149
> DMA zone: 4096 pages, LIFO batch:0
> DMA32 zone: 0 pages, LIFO batch:0
> Normal zone: 225280 pages, LIFO batch:31
> HighMem zone: 294773 pages, LIFO batch:31
> DMI 2.3 present.
> ACPI: RSDP (v000 DELL ) @ 0x000febc0
> ACPI: RSDT (v001 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd4d4
> ACPI: FADT (v001 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd50c
> ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xffff373d
> ACPI: MADT (v001 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd580
> ACPI: BOOT (v001 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd604
> ACPI: ASF! (v016 DELL WS 650 0x00000008 ASL 0x00000061) @ 0x000fd62c
> ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 15:2 APIC version 20
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled)
> Processor #6 15:2 APIC version 20
> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
> Processor #1 15:2 APIC version 20
> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] enabled)
> Processor #7 15:2 APIC version 20
> ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
> ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[24])
> IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47
> ACPI: IOAPIC (id[0x0a] address[0xfec80800] gsi_base[48])
> IOAPIC[2]: apic_id 10, version 32, address 0xfec80800, GSI 48-71
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Enabling APIC mode: Flat. Using 3 I/O APICs
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
> Built 1 zonelists
> Kernel command line: udev root=/dev/ram0 init=/linuxrc real_root=/dev/hda7 vga=ext
> mapped APIC to ffffd000 (fee00000)
> mapped IOAPIC to ffffc000 (fec00000)
> mapped IOAPIC to ffffb000 (fec80000)
> mapped IOAPIC to ffffa000 (fec80800)
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> CPU 0 irqstacks, hard=c05af000 soft=c05a7000
> PID hash table entries: 4096 (order: 12, 65536 bytes)
> Detected 2791.896 MHz processor.
> Using pmtmr for high-res timesource
> Console: colour VGA+ 80x50
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 2071896k/2096596k available (3030k kernel code, 23456k reserved, 1473k data, 232k init, 1179092k highmem)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> Calibrating delay using timer specific routine.. 5588.75 BogoMIPS (lpj=2794375)
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
> CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 0
> CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU0: Thermal monitoring enabled
> Checking 'hlt' instruction... OK.
> CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
> Booting processor 1/1 eip 2000
> CPU 1 irqstacks, hard=c05b0000 soft=c05a8000
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 5581.18 BogoMIPS (lpj=2790590)
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
> CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 0
> CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#1.
> CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU1: Thermal monitoring enabled
> CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
> Booting processor 2/6 eip 2000
> CPU 2 irqstacks, hard=c05b1000 soft=c05a9000
> Initializing CPU#2
> Calibrating delay using timer specific routine.. 5581.31 BogoMIPS (lpj=2790659)
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
> CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 3
> CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#2.
> CPU2: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU2: Thermal monitoring enabled
> CPU2: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
> Booting processor 3/7 eip 2000
> CPU 3 irqstacks, hard=c05b2000 soft=c05aa000
> Initializing CPU#3
> Calibrating delay using timer specific routine.. 5581.34 BogoMIPS (lpj=2790673)
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
> CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
> CPU: Trace cache: 12K uops, L1 D cache: 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 3
> CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#3.
> CPU3: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU3: Thermal monitoring enabled
> CPU3: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
> Total of 4 processors activated (22332.59 BogoMIPS).
> ENABLING IO-APIC IRQs
> ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
> checking TSC synchronization across 4 CPUs: passed.
> Brought up 4 CPUs
> migration_cost=1000,2000
> checking if image is initramfs... it is
> Freeing initrd memory: 753k freed
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: PCI BIOS revision 2.10 entry at 0xfbdd5, last bus=5
> PCI: Using configuration type 1
> ACPI: Subsystem revision 20060127
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
> PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
> PCI quirk: region 0880-08bf claimed by ICH4 GPIO
> PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
> Boot video device is 0000:01:00.0
> PCI: Transparent bridge - 0000:00:1e.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1.PCI2._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1.PCI3._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 15)
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 12 devices
> SCSI subsystem initialized
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
> pnp: 00:0b: ioport range 0x800-0x85f could not be reserved
> pnp: 00:0b: ioport range 0xc00-0xc7f has been reserved
> pnp: 00:0b: ioport range 0x860-0x8ff could not be reserved
> PCI: Bridge: 0000:00:01.0
> IO window: disabled.
> MEM window: fc000000-fdffffff
> PREFETCH window: f0000000-f7ffffff
> PCI: Bridge: 0000:02:1d.0
> IO window: e000-efff
> MEM window: fe300000-fe4fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:02:1f.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:02.0
> IO window: e000-efff
> MEM window: fe100000-fe4fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:1e.0
> IO window: disabled.
> MEM window: f9000000-fbffffff
> PREFETCH window: disabled.
> PCI: Setting latency timer of device 0000:00:1e.0 to 64
> Simple Boot Flag value 0x87 read from CMOS RAM was invalid
> Simple Boot Flag at 0x7a set to 0x1
> Machine check exception polling timer started.
> IA-32 Microcode Update Driver: v1.14 <[email protected]>
> highmem bounce pool size: 64 pages
> Installing knfsd (copyright (C) 1996 [email protected]).
> fuse init (API version 7.6)
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> ACPI: Power Button (FF) [PWRF]
> ACPI: Power Button (CM) [VBTN]
> Using specific hotkey driver
> lp: driver loaded but no devices found
> Real Time Clock Driver v1.12ac
> Linux agpgart interface v0.101 (c) Dave Jones
> agpgart: Detected an Intel E7505 Chipset.
> agpgart: AGP aperture is 128M @ 0xe8000000
> [drm] Initialized drm 1.0.1 20051102
> PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 1
> PNP: PS/2 controller doesn't have AUX irq; using default 12
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> serial8250: ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
> serial8250: ttyS1 at I/O 0x2f8 (irq = 0) is a 16550A
> 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> parport: PnPBIOS parport detected.
> parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
> lp0: using parport0 (interrupt-driven).
> lp0: console ready
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> loop: loaded (max 8 devices)
> Intel(R) PRO/1000 Network Driver - version 6.3.9-k2-NAPI
> Copyright (c) 1999-2005 Intel Corporation.
> ACPI: PCI Interrupt 0000:03:0e.0[A] -> GSI 24 (level, low) -> IRQ 169
> e1000: 0000:03:0e.0: e1000_probe: (PCI-X:100MHz:64-bit) 00:0d:56:09:09:fb
> e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
> PPP generic driver version 2.4.2
> PPP Deflate Compression module registered
> PPP BSD Compression module registered
> PPP MPPE Compression module registered
> NET: Registered protocol family 24
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> ICH4: IDE controller at PCI slot 0000:00:1f.1
> PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
> ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 177
> ICH4: chipset revision 1
> ICH4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
> Probing IDE interface ide0...
> hda: IC35L120AVV207-1, ATA DISK drive
> hdb: IC35L120AVV207-1, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hdc: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
> hdd: _NEC DVD+RW ND-1100A, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: max request size: 512KiB
> hda: 234375000 sectors (120000 MB) w/7965KiB Cache, CHS=16383/255/63, UDMA(100)
> hda: cache flushes supported
> hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 >
> hdb: max request size: 512KiB
> hdb: 234375000 sectors (120000 MB) w/7965KiB Cache, CHS=16383/255/63, UDMA(100)
> hdb: cache flushes supported
> hdb: hdb1 hdb2 hdb3 < hdb5 >
> hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
> SCSI Media Changer driver v0.25
> ACPI: PCI Interrupt 0000:05:0c.0[A] -> GSI 20 (level, low) -> IRQ 185
> ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[185] MMIO=[fbeff800-fbefffff] Max Packet=[2048] IR/IT contexts=[4/8]
> video1394: Installed video1394 module
> ieee1394: raw1394: /dev/raw1394 device initialized
> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
> ieee1394: sbp2: Try serialize_io=0 for better performance
> mice: PS/2 mouse device common for all mice
> input: AT Translated Set 2 keyboard as /class/input/input0
> input: PC Speaker as /class/input/input1
> I2O subsystem v1.325
> i2o: max drivers = 8
> I2O Configuration OSM v1.323
> I2O Bus Adapter OSM v1.317
> I2O Block Device OSM v1.325
> I2O SCSI Peripheral OSM v1.316
> I2O ProcFS OSM v1.316
> i2c /dev entries driver
> parport0: cannot grant exclusive access for device i2c-parport
> i2c-parport: Unable to register with parport
> : Detection failed at step 5
> i2c_adapter i2c-0: Unsupported chip (man_id=0x55, chip_id=0x20).
> i2c_adapter i2c-0: detect fail: address match, 0x2d
> pc87360: PC8736x not detected, module not inserted.
> md: linear personality registered for level -1
> md: raid0 personality registered for level 0
> md: raid1 personality registered for level 1
> md: raid10 personality registered for level 10
> md: raid5 personality registered for level 5
> md: raid4 personality registered for level 4
> raid5: automatically using best checksumming function: pIII_sse
> pIII_sse : 3536.000 MB/sec
> raid5: using function: pIII_sse (3536.000 MB/sec)
> raid6: int32x1 808 MB/s
> raid6: int32x2 972 MB/s
> raid6: int32x4 656 MB/s
> raid6: int32x8 500 MB/s
> raid6: mmxx1 1929 MB/s
> raid6: mmxx2 2546 MB/s
> raid6: sse1x1 1292 MB/s
> raid6: sse1x2 2367 MB/s
> raid6: sse2x1 3062 MB/s
> raid6: sse2x2 2804 MB/s
> raid6: using algorithm sse2x1 (3062 MB/s)
> md: raid6 personality registered for level 6
> md: faulty personality registered for level -5
> md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md: bitmap version 4.39
> device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [email protected]
> MC: drivers/edac/edac_mc.c version edac_mc Ver: 2.0.0 Mar 1 2006
> MC: drivers/edac/edac_mc.c: edac_sysfs_memctrl_setup()
> Registered '.../edac/mc' kobject
> MC: drivers/edac/edac_mc.c: edac_sysfs_pci_setup()
> Registered '.../edac/pci' kobject
> Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC).
> ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 193
> PCI: Setting latency timer of device 0000:00:1f.5 to 64
> intel8x0_measure_ac97_clock: measured 50991 usecs
> intel8x0: clocking to 48000
> ALSA device list:
> #0: Virtual MIDI Card 1
> #1: Intel 82801DB-ICH4 with AD1981B at 0xfe500400, irq 193
> NET: Registered protocol family 2
> IP route cache hash table entries: 131072 (order: 7, 524288 bytes)
> TCP established hash table entries: 262144 (order: 9, 3145728 bytes)
> TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
> TCP: Hash tables configured (established 262144 bind 65536)
> TCP reno registered
> IPv4 over IPv4 tunneling driver
> GRE over IPv4 tunneling driver
> TCP bic registered
> Initializing IPsec netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> 802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
> All bugs added by David S. Miller <[email protected]>
> p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
> Starting balanced_irq
> Using IPI Shortcut mode
> Freeing unused kernel memory: 232k freed
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 201
> PCI: Setting latency timer of device 0000:00:1d.7 to 64
> ehci_hcd 0000:00:1d.7: EHCI Host Controller
> ehci_hcd 0000:00:1d.7: debug port 1
> PCI: cache line size of 128 is not supported by device 0000:00:1d.7
> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:1d.7: irq 201, io mem 0xfe500800
> ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 6 ports detected
> ieee1394: Host added: ID:BUS[0-00:1023] GUID[86ffffffffffff00]
> usb 1-2: new high speed USB device using ehci_hcd and address 2
> usb 1-2: configuration #1 chosen from 1 choice
> hub 1-2:1.0: USB hub found
> hub 1-2:1.0: 4 ports detected
> usbcore: registered new driver hiddev
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> USB Universal Host Controller Interface driver v2.3
> ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 209
> PCI: Setting latency timer of device 0000:00:1d.0 to 64
> uhci_hcd 0000:00:1d.0: UHCI Host Controller
> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:1d.0: irq 209, io base 0x0000ff80
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 217
> PCI: Setting latency timer of device 0000:00:1d.1 to 64
> uhci_hcd 0000:00:1d.1: UHCI Host Controller
> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:1d.1: irq 217, io base 0x0000ff60
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 177
> PCI: Setting latency timer of device 0000:00:1d.2 to 64
> uhci_hcd 0000:00:1d.2: UHCI Host Controller
> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:1d.2: irq 177, io base 0x0000ff40
> usb usb4: configuration #1 chosen from 1 choice
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> usb 3-1: new low speed USB device using uhci_hcd and address 2
> usb 3-1: configuration #1 chosen from 1 choice
> input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
> input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-1
> ReiserFS: hda7: found reiserfs format "3.6" with standard journal
> ReiserFS: hda7: using ordered data mode
> ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
> ReiserFS: hda7: checking transaction log (hda7)
> ReiserFS: hda7: Using r5 hash to sort names
> Linux video capture interface: v1.00
> cx2388x v4l2 driver version 0.0.5 loaded
> ACPI: PCI Interrupt 0000:05:0e.0[A] -> GSI 22 (level, low) -> IRQ 225
> CORE cx88[0]: subsystem: 153b:1166, board: Conexant DVB-T reference design [card=19,insmod option]
> TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
> cx88[0]/0: found at 0000:05:0e.0, rev: 5, irq: 225, latency: 64, mmio: 0xfa000000
> cx88[0]/0: registered device video0 [v4l2]
> cx88[0]/0: registered device vbi0
> set_control id=0x980900 reg=0x310110 val=0x00 (mask 0xff)
> set_control id=0x980901 reg=0x310110 val=0x3f00 (mask 0xff00)
> set_control id=0x980903 reg=0x310118 val=0x00 (mask 0xff)
> set_control id=0x980902 reg=0x310114 val=0x5a7f (mask 0xffff)
> set_control id=0x980909 reg=0x320594 val=0x40 (mask 0x40) [shadowed]
> set_control id=0x980905 reg=0x320594 val=0x20 (mask 0x3f) [shadowed]
> set_control id=0x980906 reg=0x320598 val=0x40 (mask 0x7f) [shadowed]
> cx2388x dvb driver version 0.0.5 loaded
> ACPI: PCI Interrupt 0000:05:0e.2[A] -> GSI 22 (level, low) -> IRQ 225
> cx88[0]/2: found at 0000:05:0e.2, rev: 5, irq: 225, latency: 64, mmio: 0xf9000000
> cx88[0]/2: cx2388x based dvb card
> DVB: registering new adapter (cx88[0]).
> DVB: registering frontend 0 (Conexant CX22702 DVB-T)...
> microcode: CPU1 updated from revision 0xf to 0x2d, date = 08112004
> microcode: CPU3 updated from revision 0xf to 0x2d, date = 08112004
> microcode: CPU0 updated from revision 0xf to 0x2d, date = 08112004
> microcode: CPU2 updated from revision 0xf to 0x2d, date = 08112004
> Adding 987988k swap on /dev/mapper/swap1. Priority:-1 extents:1 across:987988k
> Adding 987988k swap on /dev/mapper/swap2. Priority:-2 extents:1 across:987988k
> e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex
> ReiserFS: dm-2: found reiserfs format "3.6" with standard journal
> ReiserFS: dm-2: using ordered data mode
> ReiserFS: dm-2: journal params: device dm-2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
> ReiserFS: dm-2: checking transaction log (dm-2)
> ReiserFS: dm-2: Using r5 hash to sort names
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
