Rene Engelhard <[email protected]> writes: > Emmanuel Galatoulas wrote: >> > >> >Has anyone managed to get linux-2.6.16-rc1 to boot successfully on a >> >powermac? It appears to detect the IDE controller and HDD on my mac >> >mini, but then fails to mount the root fs. (It's hard to double check >> >this because the USB keyboard isn't initialised by the failure, so I >> >can't scroll back to check.) > > Yep. same here. iBook G4. Further investigation (using netconsole) shows the breakage (in 2.6.16-rc1 and -rc2) is due to discovering an additional IDE controller (KeyLargo) before the normal (UniNorth) controller: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx +ide0: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24 PCI: Enabling device 0002:20:0d.0 (0000 -> 0002) -ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39 -hda: TOSHIBA MK8025GAS, ATA DISK drive -hdb: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive -hda: Enabling Ultra DMA 5 -hdb: Enabling Ultra DMA 2 -ide0 at 0xe1022000-0xe1022007,0xe1022160 on irq 39 -ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24 -hda: max request size: 1024KiB -hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100) -hda: cache flushes supported - hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 -hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) +ide1: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39 +hdc: TOSHIBA MK8025GAS, ATA DISK drive +hdd: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive +hdc: Enabling Ultra DMA 5 +hdd: Enabling Ultra DMA 2 +ide1 at 0xe102a000-0xe102a007,0xe102a160 on irq 39 +hdc: max request size: 512KiB +hdc: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100) +hdc: cache flushes supported + hdc: [mac] hdc1 hdc2 hdc3 hdc4 hdc5 hdc6 hdc7 +hdd: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) As a result, the IDE device names are changed and the boot fails. If the controllers were discovered in the reverse order, it wouldn't break existing installations. In both these cases the systems are G4-based PowerMacs (Mac Mini and iBook). In the case of the Mini, I'm not even certain it's physically possible to use this additional controller, given how closed the system is. Regards, Roger -- Roger Leigh Printing on GNU/Linux? http://gutenprint.sourceforge.net/ Debian GNU/Linux http://www.debian.org/ GPG Public Key: 0x25BFB848. Please sign and encrypt your mail.
$ netcat -u -l -p 4444 Total memory = 512MB; using 1024kB for hash table (at c0400000) Linux version 2.6.15.1 (rleigh@hardknott) (gcc version 4.0.3 20060115 (prerelease) (Debian 4.0.2-7)) #22 Wed Feb 8 20:44:14 GMT 2006 Found UniNorth memory controller & host bridge, revision: 210 Mapped at 0xfddf4000 Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdd74000 Processor NAP mode on idle enabled. PowerMac motherboard: Mac mini Enabling clock spreading on Intrepid ASIC Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0 Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0 Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0 via-pmu: Server Mode is disabled PMU driver 2 initialized for Core99, firmware: 55 nvram: Checking bank 0... nvram: gen0=470, gen1=469 nvram: Active bank is: 0 nvram: OF partition at 0x410 nvram: XP partition at 0x1020 nvram: NR partition at 0x1120 Built 1 zonelists Kernel command line: root=/dev/hda3 ro video=radeonfb:1680x1050-32@60 netconsole=@1/,[email protected]/ netconsole: local port 6665 netconsole: local IP 1.0.0.0 netconsole: interface eth0 netconsole: remote port 4444 netconsole: remote IP 10.0.0.12 netconsole: remote ethernet address ff:ff:ff:ff:ff:ff PowerMac using OpenPIC irq controller at 0x80040000 OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc523000 OpenPIC timer frequency is 4.166666 MHz PID hash table entries: 4096 (order: 12, 65536 bytes) GMT Delta read from XPRAM: 0 minutes, DST: off time_init: decrementer frequency = 41.620997 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 514048k available (2696k kernel code, 1044k data, 164k init, 0k highmem) AGP special page: 0xdffff000 Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 device-tree: property "l2-cache" name conflicts with node in /cpus/PowerPC,G4@0 NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Cannot allocate resource region 0 of device 0001:10:18.0 PCI: Cannot allocate resource region 0 of device 0001:10:19.0 Apple USB OHCI 0001:10:18.0 disabled by firmware Apple USB OHCI 0001:10:19.0 disabled by firmware SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub Thermal assist unit not available audit: initializing netlink socket (disabled) audit(1139431511.116:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered PCI: Enabling device 0000:00:10.0 (0006 -> 0007) radeonfb: Retreived PLL infos from Open Firmware radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=250.00 MHz radeonfb: PLL min 12000 max 35000 radeonfb: Monitor 1 type DFP found radeonfb: EDID probed radeonfb: Monitor 2 type DFP found radeonfb: EDID probed Console: switching to colour frame buffer device 210x65 radeonfb (0000:00:10.0): ATI Radeon Yb Generic RTC Driver v1.07 Macintosh non-volatile memory driver v1.1 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected Apple UniNorth 2 chipset agpgart: configuring for size idx: 4 agpgart: AGP aperture is 16M @ 0x0 [drm] Initialized drm 1.0.0 20040925 [drm] Initialized radeon 1.19.0 20050911 on minor 0: sungem.c:v0.98 8/24/03 David S. Miller ([email protected]) eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:75:6d:56 eth0: Found BCM5221 PHY netconsole: device eth0 not up yet, forcing it eth0: Link is up at 100 Mbps, full-duplex. eth0: Pause is disabled netconsole: network logging started MacIO PCI driver attached to Intrepid chipset input: Macintosh mouse button emulation as /class/input/input0 apm_emu: APM Emulation 0.5 initialized. adb: starting probe task... adb: finished probe task... Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PCI: Enabling device 0002:20:0d.0 (0000 -> 0002) ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39 hda: TOSHIBA MK8025GAS, ATA DISK drive hdb: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive hda: Enabling Ultra DMA 5 hdb: Enabling Ultra DMA 2 ide0 at 0xe1022000-0xe1022007,0xe1022160 on irq 39 ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24 hda: max request size: 1024KiB hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 usbmon: debugfs is not available PCI: Enabling device 0001:10:1b.2 (0004 -> 0006) ehci_hcd 0001:10:1b.2: EHCI Host Controller ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 1 ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000 ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.15.1 ehci_hcd usb usb1: SerialNumber: 0001:10:1b.2 hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected Apple USB OHCI 0001:10:18.0 disabled by firmware Apple USB OHCI 0001:10:19.0 disabled by firmware PCI: Enabling device 0001:10:1a.0 (0000 -> 0002) ohci_hcd 0001:10:1a.0: OHCI Host Controller ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2 ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.15.1 ohci_hcd usb usb2: SerialNumber: 0001:10:1a.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PCI: Enabling device 0001:10:1b.0 (0000 -> 0002) ohci_hcd 0001:10:1b.0: OHCI Host Controller ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 3 ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000 usb 1-2: new high speed USB device using ehci_hcd and address 3 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 2.6.15.1 ohci_hcd usb usb3: SerialNumber: 0001:10:1b.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 3 ports detected hub 1-2:1.0: USB hub found hub 1-2:1.0: 3 ports detected PCI: Enabling device 0001:10:1b.1 (0000 -> 0002) ohci_hcd 0001:10:1b.1: OHCI Host Controller ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4 ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000 usb usb4: Product: OHCI Host Controller usb usb4: Manufacturer: Linux 2.6.15.1 ohci_hcd usb usb4: SerialNumber: 0001:10:1b.1 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v2.3 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usb 3-1: new full speed USB device using ohci_hcd and address 2 usb 3-1: Product: Hub in Apple Extended USB Keyboard usb 3-1: Manufacturer: Mitsumi Electric hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usbcore: registered new driver hiddev usb 1-2.2: new low speed USB device using ehci_hcd and address 4 usb 1-2.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM) usb 1-2.2: Manufacturer: Microsoft usb 1-2.3: new low speed USB device using ehci_hcd and address 5 usb 1-2.3: Product: Apple Cinema Display input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input1 input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0001:10:1b.2-2.2 hiddev0: USB HID v1.11 Device [Apple Cinema Display] on usb-0001:10:1b.2-2.3 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice i2c /dev entries driver Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected] dmasound_pmac: couldn't find a Codec we can handle NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 164k init usb 3-1.1: new full speed USB device using ohci_hcd and address 3 usb 3-1.1: Product: USB DRIVE usb 3-1.1: Manufacturer: KINGSTON usb 3-1.1: SerialNumber: 1120046114165 scsi0 : SCSI emulation for USB Mass Storage devices usb 3-1.3: new full speed USB device using ohci_hcd and address 4 usb 3-1.3: Product: Apple Extended USB Keyboard usb 3-1.3: Manufacturer: Mitsumi Electric input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2 input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input3 input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 ohci1394: $Rev: 1313 $ Ben Collins <[email protected]> PCI: Enabling device 0002:20:0e.0 (0000 -> 0002) ohci1394: fw-host0: Unexpected PCI resource length of 1000! ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048] Vendor: KINGSTON Model: USB DRIVE Rev: 1.12 Type: Direct-Access ANSI SCSI revision: 01 CCS SCSI device sda: 251904 512-byte hdwr sectors (129 MB) sda: Write Protect is off sda: assuming drive cache: write through hda: Enabling Ultra DMA 5 SCSI device sda: 251904 512-byte hdwr sectors (129 MB) sda: Write Protect is off sda: assuming drive cache: write through sda:<7>usb-storage: queuecommand called sda1 sda2 sd 0:0:0:0: Attached scsi removable disk sda eth1394: $Rev: 1312 $ Ben Collins <[email protected]> eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) hda: Enabling Ultra DMA 5 EXT3 FS on hda3, internal journal sbp2: $Rev: 1306 $ Ben Collins <[email protected]> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance input: PowerMac Beep as /class/input/input4 device-mapper: snapshot is marked invalid kjournald starting. Commit interval 5 seconds EXT3 FS on dm-5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-3, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on dm-6, internal journal EXT3-fs: mounted filesystem with ordered data mode. HFS+-fs: write access to a jounaled filesystem is not supported, use the force option at your own risk, mounting read-only. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-7, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-9, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-14, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 2097144k swap on /dev/mapper/hda_vg-swap0. Priority:2 extents:1 across:2097144k Adding 2097144k swap on /dev/mapper/hda_vg-swap1. Priority:1 extents:1 across:2097144k Adding 2097144k swap on /dev/mapper/hda_vg-swap2. Priority:3 extents:1 across:2097144k NET: Registered protocol family 17 sixxs: Disabled Privacy Extensions Installing knfsd (copyright (C) 1996 [email protected]). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist NFSD: starting 90-second grace period agpgart: Putting AGP V2 device at 0000:00:0b.0 into 1x mode agpgart: Putting AGP V2 device at 0000:00:10.0 into 1x mode [drm] Loading R200 Microcode usb 3-1: USB disconnect, address 2 usb 3-1.1: USB disconnect, address 3 usb 3-1.3: USB disconnect, address 4 usb 3-1: new full speed USB device using ohci_hcd and address 5 usb 3-1: Product: Hub in Apple Extended USB Keyboard usb 3-1: Manufacturer: Mitsumi Electric hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 3-1.1: new full speed USB device using ohci_hcd and address 6 usb 3-1.1: Product: USB DRIVE usb 3-1.1: Manufacturer: KINGSTON usb 3-1.1: SerialNumber: 1120046114165 scsi1 : SCSI emulation for USB Mass Storage devices usb 3-1.3: new full speed USB device using ohci_hcd and address 7 usb 3-1.3: Product: Apple Extended USB Keyboard usb 3-1.3: Manufacturer: Mitsumi Electric input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input5 input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input6 input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 usbcore: registered new driver ub Vendor: KINGSTON Model: USB DRIVE Rev: 1.12 Type: Direct-Access ANSI SCSI revision: 01 CCS SCSI device sda: 251904 512-byte hdwr sectors (129 MB) sda: Write Protect is off sda: assuming drive cache: write through SCSI device sda: 251904 512-byte hdwr sectors (129 MB) sda: Write Protect is off sda: assuming drive cache: write through sda:<7>usb-storage: queuecommand called sda1 sda2 sd 1:0:0:0: Attached scsi removable disk sda
$ netcat -u -l -p 4444 Total memory = 512MB; using 1024kB for hash table (at cff00000) Linux version 2.6.16-rc2 (rleigh@hardknott) (gcc version 4.0.3 20060115 (prerelease) (Debian 4.0.2-7)) #4 Wed Feb 8 18:56:44 GMT 2006 Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xd2 Mapped at 0xfdfc0000 Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000 Processor NAP mode on idle enabled. PowerMac motherboard: Mac mini Using native/NAP idle loop Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0 Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0 Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0 via-pmu: Server Mode is disabled PMU driver v2 initialized for Core99, firmware: 55 nvram: Checking bank 0... nvram: gen0=470, gen1=469 nvram: Active bank is: 0 nvram: OF partition at 0x410 nvram: XP partition at 0x1020 nvram: NR partition at 0x1120 Top of RAM: 0x20000000, Total RAM: 0x20000000 Memory hole size: 0MB Built 1 zonelists Kernel command line: root=/dev/hda3 ro video=radeonfb:1680x1050-32@60 netconsole=@1/,[email protected]/ netconsole: local port 6665 netconsole: local IP 1.0.0.0 netconsole: interface eth0 netconsole: remote port 4444 netconsole: remote IP 10.0.0.12 netconsole: remote ethernet address ff:ff:ff:ff:ff:ff mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs mpic: ISU size: 64, shift: 6, mask: 3f mpic: Initializing for 64 sources PID hash table entries: 4096 (order: 12, 65536 bytes) GMT Delta read from XPRAM: 0 minutes, DST: off time_init: decrementer frequency = 41.620997 MHz time_init: processor frequency = 1416.666661 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 514048k/524288k available (2996k kernel code, 9744k reserved, 308k data, 190k bss, 148k init) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 device-tree: property "l2-cache" name conflicts with node in /cpus/PowerPC,G4@0 NET: Registered protocol family 16 KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000 channel 0 bus <multibus> channel 1 bus <multibus> KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000 channel 0 bus <multibus> PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c channel 1 bus <multibus> channel 2 bus <multibus> pmf: registering driver for node /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c/temp-monitor@190 pmf: no functions, disposing.. Installing base platform functions... Installing MMIO functions for macio /pci@f2000000/mac-io@17 pmf: registering driver for node /pci@f2000000/mac-io@17 pmf: Adding functions for platform-do-wor-enable pmf: idx 1: flags=08000000, phandle=ff97f4d0 16 bytes remaining, parsing... pmf: Added 1 functions pmf: Adding functions for platform-do-wor-disable pmf: idx 1: flags=08000000, phandle=ff97f4d0 16 bytes remaining, parsing... pmf: Added 1 functions Installing GPIO functions for macio /pci@f2000000/mac-io@17 pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/modem-reset@1d pmf: Adding functions for platform-do-modem-reset pmf: idx 1: flags=08000000, phandle=ff975e48 12 bytes remaining, parsing... pmf: Added 1 functions pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/modem-power@1c pmf: Adding functions for platform-do-modem-power pmf: idx 1: flags=08000000, phandle=ff975e48 40 bytes remaining, parsing... pmf: Added 1 functions pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/extint-gpio1@9 pmf: no functions, disposing.. pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/programmer-switch@11 pmf: no functions, disposing.. pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/gpio5@6f pmf: no functions, disposing.. pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/gpio6@70 pmf: no functions, disposing.. pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67 pmf: no functions, disposing.. Calling initial GPIO functions for macio /pci@f2000000/mac-io@17 Installing functions for UniN /uni-n@f8000000 pmf: registering driver for node /uni-n@f8000000 pmf: no functions, disposing.. Installing functions for UniN clock /uni-n@f8000000/hw-clock pmf: registering driver for node /uni-n@f8000000/hw-clock pmf: Adding functions for platform-do-clockspreading pmf: idx 1: flags=20000000, phandle=00000000 56 bytes remaining, parsing... pmf: idx 2: flags=10000000, phandle=00000000 16 bytes remaining, parsing... pmf: Added 2 functions All base functions installed PCI: Probing PCI hardware PCI: Cannot allocate resource region 0 of device 0001:10:18.0 PCI: Cannot allocate resource region 0 of device 0001:10:19.0 Apple USB OHCI 0001:10:18.0 disabled by firmware Apple USB OHCI 0001:10:19.0 disabled by firmware SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub Thermal assist unit not available audit: initializing netlink socket (disabled) audit(1139426338.104:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Enabling device 0000:00:10.0 (0006 -> 0007) radeonfb: Retrieved PLL infos from Open Firmware radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=250.00 MHz radeonfb: PLL min 12000 max 35000 radeonfb: Monitor 1 type DFP found radeonfb: EDID probed radeonfb: Monitor 2 type DFP found radeonfb: EDID probed Console: switching to colour frame buffer device 210x65 radeonfb (0000:00:10.0): ATI Radeon Yb Generic RTC Driver v1.07 Macintosh non-volatile memory driver v1.1 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected Apple UniNorth 2 chipset agpgart: configuring for size idx: 4 agpgart: AGP aperture is 16M @ 0x0 [drm] Initialized drm 1.0.1 20051102 [drm] Initialized radeon 1.21.0 20051229 on minor 0 sungem.c:v0.98 8/24/03 David S. Miller ([email protected]) eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:75:6d:56 eth0: Found BCM5221 PHY netconsole: device eth0 not up yet, forcing it eth0: Link is up at 100 Mbps, full-duplex. eth0: Pause is disabled netconsole: network logging started MacIO PCI driver attached to Intrepid chipset adb: starting probe task... adb: finished probe task... Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24 PCI: Enabling device 0002:20:0d.0 (0000 -> 0002) ide1: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39 hdc: TOSHIBA MK8025GAS, ATA DISK drive hdd: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive hdc: Enabling Ultra DMA 5 hdd: Enabling Ultra DMA 2 ide1 at 0xe102a000-0xe102a007,0xe102a160 on irq 39 hdc: max request size: 512KiB hdc: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100) hdc: cache flushes supported hdc: [mac] hdc1 hdc2 hdc3 hdc4 hdc5 hdc6 hdc7 hdd: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 usbmon: debugfs is not available PCI: Enabling device 0001:10:1b.2 (0004 -> 0006) ehci_hcd 0001:10:1b.2: EHCI Host Controller ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 1 ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000 ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.16-rc2 ehci_hcd usb usb1: SerialNumber: 0001:10:1b.2 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected Apple USB OHCI 0001:10:18.0 disabled by firmware Apple USB OHCI 0001:10:19.0 disabled by firmware PCI: Enabling device 0001:10:1a.0 (0000 -> 0002) ohci_hcd 0001:10:1a.0: OHCI Host Controller ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2 ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.16-rc2 ohci_hcd usb usb2: SerialNumber: 0001:10:1a.0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PCI: Enabling device 0001:10:1b.0 (0000 -> 0002) ohci_hcd 0001:10:1b.0: OHCI Host Controller ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 3 ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000 usb 1-2: new high speed USB device using ehci_hcd and address 3 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 2.6.16-rc2 ohci_hcd usb usb3: SerialNumber: 0001:10:1b.0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 3 ports detected usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 3 ports detected PCI: Enabling device 0001:10:1b.1 (0000 -> 0002) ohci_hcd 0001:10:1b.1: OHCI Host Controller ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4 ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000 usb usb4: Product: OHCI Host Controller usb usb4: Manufacturer: Linux 2.6.16-rc2 ohci_hcd usb usb4: SerialNumber: 0001:10:1b.1 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v2.3 Initializing USB Mass Storage driver... usb 3-1: new full speed USB device using ohci_hcd and address 2 usb 3-1: Product: Hub in Apple Extended USB Keyboard usb 3-1: Manufacturer: Mitsumi Electric usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected usb 1-2.2: new low speed USB device using ehci_hcd and address 4 usb 1-2.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM) usb 1-2.2: Manufacturer: Microsoft usb 1-2.2: configuration #1 chosen from 1 choice usb 1-2.3: new low speed USB device using ehci_hcd and address 5 usb 1-2.3: Product: Apple Cinema Display usb 1-2.3: configuration #1 chosen from 1 choice usb 3-1.1: new full speed USB device using ohci_hcd and address 3 usb 3-1.1: Product: USB DRIVE usb 3-1.1: Manufacturer: KINGSTON usb 3-1.1: SerialNumber: 1120046114165 usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.3: new full speed USB device using ohci_hcd and address 4 usb 3-1.3: Product: Apple Extended USB Keyboard usb 3-1.3: Manufacturer: Mitsumi Electric usb 3-1.3: configuration #1 chosen from 1 choice scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input0 input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0001:10:1b.2-2.2 hiddev0: USB HID v1.11 Device [Apple Cinema Display] on usb-0001:10:1b.2-2.3 input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input1 input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2 input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice i2c /dev entries driver PowerMac i2c bus pmu 2 registered PowerMac i2c bus pmu 1 registered PowerMac i2c bus mac-io 0 registered PowerMac i2c bus uni-n 1 registered PowerMac i2c bus uni-n 0 registered device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [email protected] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver VFS: Cannot open root device "hda3" or unknown-block(0,0) Please append a correct "root=" boot option Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) <0>Rebooting in 180 seconds..<7>eth0: no IPv6 routers present
--- bootlog-2.6.15-ppc 2006-02-11 13:24:36.000000000 +0000 +++ bootlog-2.6.16-rc2-ppc 2006-02-11 13:24:40.000000000 +0000 @@ -1,23 +1,25 @@ $ netcat -u -l -p 4444 -Total memory = 512MB; using 1024kB for hash table (at c0400000) -Linux version 2.6.15.1 (rleigh@hardknott) (gcc version 4.0.3 20060115 (prerelease) (Debian 4.0.2-7)) #22 Wed Feb 8 20:44:14 GMT 2006 -Found UniNorth memory controller & host bridge, revision: 210 -Mapped at 0xfddf4000 -Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdd74000 +Total memory = 512MB; using 1024kB for hash table (at cff00000) +Linux version 2.6.16-rc2 (rleigh@hardknott) (gcc version 4.0.3 20060115 (prerelease) (Debian 4.0.2-7)) #4 Wed Feb 8 18:56:44 GMT 2006 +Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xd2 +Mapped at 0xfdfc0000 +Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000 Processor NAP mode on idle enabled. PowerMac motherboard: Mac mini -Enabling clock spreading on Intrepid ASIC +Using native/NAP idle loop Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0 Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0 Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0 via-pmu: Server Mode is disabled -PMU driver 2 initialized for Core99, firmware: 55 +PMU driver v2 initialized for Core99, firmware: 55 nvram: Checking bank 0... nvram: gen0=470, gen1=469 nvram: Active bank is: 0 nvram: OF partition at 0x410 nvram: XP partition at 0x1020 nvram: NR partition at 0x1120 +Top of RAM: 0x20000000, Total RAM: 0x20000000 +Memory hole size: 0MB Built 1 zonelists Kernel command line: root=/dev/hda3 ro video=radeonfb:1680x1050-32@60 netconsole=@1/,[email protected]/ netconsole: local port 6665 @@ -26,17 +28,17 @@ netconsole: remote port 4444 netconsole: remote IP 10.0.0.12 netconsole: remote ethernet address ff:ff:ff:ff:ff:ff -PowerMac using OpenPIC irq controller at 0x80040000 -OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc523000 -OpenPIC timer frequency is 4.166666 MHz +mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs +mpic: ISU size: 64, shift: 6, mask: 3f +mpic: Initializing for 64 sources PID hash table entries: 4096 (order: 12, 65536 bytes) GMT Delta read from XPRAM: 0 minutes, DST: off time_init: decrementer frequency = 41.620997 MHz +time_init: processor frequency = 1416.666661 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) -Memory: 514048k available (2696k kernel code, 1044k data, 164k init, 0k highmem) -AGP special page: 0xdffff000 +Memory: 514048k/524288k available (2996k kernel code, 9744k reserved, 308k data, 190k bss, 148k init) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode @@ -45,6 +47,55 @@ Mount-cache hash table entries: 512 device-tree: property "l2-cache" name conflicts with node in /cpus/PowerPC,G4@0 NET: Registered protocol family 16 +KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000 + channel 0 bus <multibus> + channel 1 bus <multibus> +KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000 + channel 0 bus <multibus> +PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c + channel 1 bus <multibus> + channel 2 bus <multibus> +pmf: registering driver for node /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c/temp-monitor@190 +pmf: no functions, disposing.. +Installing base platform functions... +Installing MMIO functions for macio /pci@f2000000/mac-io@17 +pmf: registering driver for node /pci@f2000000/mac-io@17 +pmf: Adding functions for platform-do-wor-enable +pmf: idx 1: flags=08000000, phandle=ff97f4d0 16 bytes remaining, parsing... +pmf: Added 1 functions +pmf: Adding functions for platform-do-wor-disable +pmf: idx 1: flags=08000000, phandle=ff97f4d0 16 bytes remaining, parsing... +pmf: Added 1 functions +Installing GPIO functions for macio /pci@f2000000/mac-io@17 +pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/modem-reset@1d +pmf: Adding functions for platform-do-modem-reset +pmf: idx 1: flags=08000000, phandle=ff975e48 12 bytes remaining, parsing... +pmf: Added 1 functions +pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/modem-power@1c +pmf: Adding functions for platform-do-modem-power +pmf: idx 1: flags=08000000, phandle=ff975e48 40 bytes remaining, parsing... +pmf: Added 1 functions +pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/extint-gpio1@9 +pmf: no functions, disposing.. +pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/programmer-switch@11 +pmf: no functions, disposing.. +pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/gpio5@6f +pmf: no functions, disposing.. +pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/gpio6@70 +pmf: no functions, disposing.. +pmf: registering driver for node /pci@f2000000/mac-io@17/gpio@50/extint-gpio15@67 +pmf: no functions, disposing.. +Calling initial GPIO functions for macio /pci@f2000000/mac-io@17 +Installing functions for UniN /uni-n@f8000000 +pmf: registering driver for node /uni-n@f8000000 +pmf: no functions, disposing.. +Installing functions for UniN clock /uni-n@f8000000/hw-clock +pmf: registering driver for node /uni-n@f8000000/hw-clock +pmf: Adding functions for platform-do-clockspreading +pmf: idx 1: flags=20000000, phandle=00000000 56 bytes remaining, parsing... +pmf: idx 2: flags=10000000, phandle=00000000 16 bytes remaining, parsing... +pmf: Added 2 functions +All base functions installed PCI: Probing PCI hardware PCI: Cannot allocate resource region 0 of device 0001:10:18.0 PCI: Cannot allocate resource region 0 of device 0001:10:19.0 @@ -55,16 +106,16 @@ usbcore: registered new driver hub Thermal assist unit not available audit: initializing netlink socket (disabled) -audit(1139431511.116:1): initialized +audit(1139426338.104:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered -io scheduler cfq registered +io scheduler cfq registered (default) PCI: Enabling device 0000:00:10.0 (0006 -> 0007) -radeonfb: Retreived PLL infos from Open Firmware +radeonfb: Retrieved PLL infos from Open Firmware radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=250.00 MHz radeonfb: PLL min 12000 max 35000 radeonfb: Monitor 1 type DFP found @@ -79,8 +130,8 @@ agpgart: Detected Apple UniNorth 2 chipset agpgart: configuring for size idx: 4 agpgart: AGP aperture is 16M @ 0x0 -[drm] Initialized drm 1.0.0 20040925 -[drm] Initialized radeon 1.19.0 20050911 on minor 0: +[drm] Initialized drm 1.0.1 20051102 +[drm] Initialized radeon 1.21.0 20051229 on minor 0 sungem.c:v0.98 8/24/03 David S. Miller ([email protected]) eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:75:6d:56 eth0: Found BCM5221 PHY @@ -89,25 +140,23 @@ eth0: Pause is disabled netconsole: network logging started MacIO PCI driver attached to Intrepid chipset -input: Macintosh mouse button emulation as /class/input/input0 -apm_emu: APM Emulation 0.5 initialized. adb: starting probe task... adb: finished probe task... Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx +ide0: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24 PCI: Enabling device 0002:20:0d.0 (0000 -> 0002) -ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39 -hda: TOSHIBA MK8025GAS, ATA DISK drive -hdb: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive -hda: Enabling Ultra DMA 5 -hdb: Enabling Ultra DMA 2 -ide0 at 0xe1022000-0xe1022007,0xe1022160 on irq 39 -ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24 -hda: max request size: 1024KiB -hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100) -hda: cache flushes supported - hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 -hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) +ide1: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39 +hdc: TOSHIBA MK8025GAS, ATA DISK drive +hdd: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive +hdc: Enabling Ultra DMA 5 +hdd: Enabling Ultra DMA 2 +ide1 at 0xe102a000-0xe102a007,0xe102a160 on irq 39 +hdc: max request size: 512KiB +hdc: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100) +hdc: cache flushes supported + hdc: [mac] hdc1 hdc2 hdc3 hdc4 hdc5 hdc6 hdc7 +hdd: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 usbmon: debugfs is not available PCI: Enabling device 0001:10:1b.2 (0004 -> 0006) @@ -116,8 +165,9 @@ ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000 ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: Product: EHCI Host Controller -usb usb1: Manufacturer: Linux 2.6.15.1 ehci_hcd +usb usb1: Manufacturer: Linux 2.6.16-rc2 ehci_hcd usb usb1: SerialNumber: 0001:10:1b.2 +usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected Apple USB OHCI 0001:10:18.0 disabled by firmware @@ -127,8 +177,9 @@ ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 2 ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000 usb usb2: Product: OHCI Host Controller -usb usb2: Manufacturer: Linux 2.6.15.1 ohci_hcd +usb usb2: Manufacturer: Linux 2.6.16-rc2 ohci_hcd usb usb2: SerialNumber: 0001:10:1a.0 +usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PCI: Enabling device 0001:10:1b.0 (0000 -> 0002) @@ -137,10 +188,12 @@ ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000 usb 1-2: new high speed USB device using ehci_hcd and address 3 usb usb3: Product: OHCI Host Controller -usb usb3: Manufacturer: Linux 2.6.15.1 ohci_hcd +usb usb3: Manufacturer: Linux 2.6.16-rc2 ohci_hcd usb usb3: SerialNumber: 0001:10:1b.0 +usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 3 ports detected +usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 3 ports detected PCI: Enabling device 0001:10:1b.1 (0000 -> 0002) @@ -148,36 +201,56 @@ ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4 ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000 usb usb4: Product: OHCI Host Controller -usb usb4: Manufacturer: Linux 2.6.15.1 ohci_hcd +usb usb4: Manufacturer: Linux 2.6.16-rc2 ohci_hcd usb usb4: SerialNumber: 0001:10:1b.1 +usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v2.3 Initializing USB Mass Storage driver... -usbcore: registered new driver usb-storage -USB Mass Storage support registered. usb 3-1: new full speed USB device using ohci_hcd and address 2 usb 3-1: Product: Hub in Apple Extended USB Keyboard usb 3-1: Manufacturer: Mitsumi Electric +usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected -usbcore: registered new driver hiddev usb 1-2.2: new low speed USB device using ehci_hcd and address 4 usb 1-2.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM) usb 1-2.2: Manufacturer: Microsoft +usb 1-2.2: configuration #1 chosen from 1 choice usb 1-2.3: new low speed USB device using ehci_hcd and address 5 usb 1-2.3: Product: Apple Cinema Display -input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input1 +usb 1-2.3: configuration #1 chosen from 1 choice +usb 3-1.1: new full speed USB device using ohci_hcd and address 3 +usb 3-1.1: Product: USB DRIVE +usb 3-1.1: Manufacturer: KINGSTON +usb 3-1.1: SerialNumber: 1120046114165 +usb 3-1.1: configuration #1 chosen from 1 choice +usb 3-1.3: new full speed USB device using ohci_hcd and address 4 +usb 3-1.3: Product: Apple Extended USB Keyboard +usb 3-1.3: Manufacturer: Mitsumi Electric +usb 3-1.3: configuration #1 chosen from 1 choice +scsi0 : SCSI emulation for USB Mass Storage devices +usbcore: registered new driver usb-storage +USB Mass Storage support registered. +usbcore: registered new driver hiddev +input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input0 input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0001:10:1b.2-2.2 hiddev0: USB HID v1.11 Device [Apple Cinema Display] on usb-0001:10:1b.2-2.3 +input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input1 +input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 +input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2 +input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice i2c /dev entries driver -Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits -Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits -device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected] -dmasound_pmac: couldn't find a Codec we can handle +PowerMac i2c bus pmu 2 registered +PowerMac i2c bus pmu 1 registered +PowerMac i2c bus mac-io 0 registered +PowerMac i2c bus uni-n 1 registered +PowerMac i2c bus uni-n 0 registered +device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [email protected] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) @@ -189,111 +262,7 @@ NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver -kjournald starting. Commit interval 5 seconds -EXT3-fs: mounted filesystem with ordered data mode. -VFS: Mounted root (ext3 filesystem) readonly. -Freeing unused kernel memory: 164k init -usb 3-1.1: new full speed USB device using ohci_hcd and address 3 -usb 3-1.1: Product: USB DRIVE -usb 3-1.1: Manufacturer: KINGSTON -usb 3-1.1: SerialNumber: 1120046114165 -scsi0 : SCSI emulation for USB Mass Storage devices -usb 3-1.3: new full speed USB device using ohci_hcd and address 4 -usb 3-1.3: Product: Apple Extended USB Keyboard -usb 3-1.3: Manufacturer: Mitsumi Electric -input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2 -input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 -input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input3 -input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 -ohci1394: $Rev: 1313 $ Ben Collins <[email protected]> -PCI: Enabling device 0002:20:0e.0 (0000 -> 0002) -ohci1394: fw-host0: Unexpected PCI resource length of 1000! -ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048] - Vendor: KINGSTON Model: USB DRIVE Rev: 1.12 - Type: Direct-Access ANSI SCSI revision: 01 CCS -SCSI device sda: 251904 512-byte hdwr sectors (129 MB) -sda: Write Protect is off -sda: assuming drive cache: write through -hda: Enabling Ultra DMA 5 -SCSI device sda: 251904 512-byte hdwr sectors (129 MB) -sda: Write Protect is off -sda: assuming drive cache: write through - sda:<7>usb-storage: queuecommand called - sda1 sda2 -sd 0:0:0:0: Attached scsi removable disk sda -eth1394: $Rev: 1312 $ Ben Collins <[email protected]> -eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) -hda: Enabling Ultra DMA 5 -EXT3 FS on hda3, internal journal -sbp2: $Rev: 1306 $ Ben Collins <[email protected]> -ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) -ieee1394: sbp2: Try serialize_io=0 for better performance -input: PowerMac Beep as /class/input/input4 -device-mapper: snapshot is marked invalid -kjournald starting. Commit interval 5 seconds -EXT3 FS on dm-5, internal journal -EXT3-fs: mounted filesystem with ordered data mode. -kjournald starting. Commit interval 5 seconds -EXT3 FS on dm-3, internal journal -EXT3-fs: mounted filesystem with ordered data mode. -kjournald starting. Commit interval 5 seconds -EXT3 FS on dm-4, internal journal -EXT3-fs: mounted filesystem with ordered data mode. -kjournald starting. Commit interval 5 seconds -EXT3-fs warning: maximal mount count reached, running e2fsck is recommended -EXT3 FS on dm-6, internal journal -EXT3-fs: mounted filesystem with ordered data mode. -HFS+-fs: write access to a jounaled filesystem is not supported, use the force option at your own risk, mounting read-only. -kjournald starting. Commit interval 5 seconds -EXT3 FS on dm-7, internal journal -EXT3-fs: mounted filesystem with ordered data mode. -kjournald starting. Commit interval 5 seconds -EXT3 FS on dm-9, internal journal -EXT3-fs: mounted filesystem with ordered data mode. -kjournald starting. Commit interval 5 seconds -EXT3 FS on dm-14, internal journal -EXT3-fs: mounted filesystem with ordered data mode. -Adding 2097144k swap on /dev/mapper/hda_vg-swap0. Priority:2 extents:1 across:2097144k -Adding 2097144k swap on /dev/mapper/hda_vg-swap1. Priority:1 extents:1 across:2097144k -Adding 2097144k swap on /dev/mapper/hda_vg-swap2. Priority:3 extents:1 across:2097144k -NET: Registered protocol family 17 -sixxs: Disabled Privacy Extensions -Installing knfsd (copyright (C) 1996 [email protected]). -NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory -NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist -NFSD: starting 90-second grace period -agpgart: Putting AGP V2 device at 0000:00:0b.0 into 1x mode -agpgart: Putting AGP V2 device at 0000:00:10.0 into 1x mode -[drm] Loading R200 Microcode -usb 3-1: USB disconnect, address 2 -usb 3-1.1: USB disconnect, address 3 -usb 3-1.3: USB disconnect, address 4 -usb 3-1: new full speed USB device using ohci_hcd and address 5 -usb 3-1: Product: Hub in Apple Extended USB Keyboard -usb 3-1: Manufacturer: Mitsumi Electric -hub 3-1:1.0: USB hub found -hub 3-1:1.0: 3 ports detected -usb 3-1.1: new full speed USB device using ohci_hcd and address 6 -usb 3-1.1: Product: USB DRIVE -usb 3-1.1: Manufacturer: KINGSTON -usb 3-1.1: SerialNumber: 1120046114165 -scsi1 : SCSI emulation for USB Mass Storage devices -usb 3-1.3: new full speed USB device using ohci_hcd and address 7 -usb 3-1.3: Product: Apple Extended USB Keyboard -usb 3-1.3: Manufacturer: Mitsumi Electric -input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input5 -input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 -input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input6 -input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:10:1b.0-1.3 -usbcore: registered new driver ub - Vendor: KINGSTON Model: USB DRIVE Rev: 1.12 - Type: Direct-Access ANSI SCSI revision: 01 CCS -SCSI device sda: 251904 512-byte hdwr sectors (129 MB) -sda: Write Protect is off -sda: assuming drive cache: write through -SCSI device sda: 251904 512-byte hdwr sectors (129 MB) -sda: Write Protect is off -sda: assuming drive cache: write through - sda:<7>usb-storage: queuecommand called - sda1 sda2 -sd 1:0:0:0: Attached scsi removable disk sda +VFS: Cannot open root device "hda3" or unknown-block(0,0) +Please append a correct "root=" boot option +Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) + <0>Rebooting in 180 seconds..<7>eth0: no IPv6 routers present
Attachment:
pgpvKhI4zJKTw.pgp
Description: PGP signature
- Follow-Ups:
- Re: 2.6.16-rc1
- From: Benjamin Herrenschmidt <[email protected]>
- Re: 2.6.16-rc1
- Prev by Date: [PATCH] x86: gitignore some autogenerated files for i386
- Next by Date: Re: [ 00/10] [Suspend2] Modules support.
- Previous by thread: [PATCH] x86: gitignore some autogenerated files for i386
- Next by thread: Re: 2.6.16-rc1
- Index(es):
 |