A few trivial updates for the microdev board support code:
- Update for __IO_PREFIX changes.
- Consolidate headers into a single microdev.h.
- Update the microdev_defconfig.
- Add init values for the S1D13806 used by s1d13xxxfb.
Signed-off-by: Paul Mundt <[email protected]>
---
arch/sh/boards/superh/microdev/io.c | 192 +++++++--------
arch/sh/boards/superh/microdev/irq.c | 2
arch/sh/boards/superh/microdev/setup.c | 168 ++++++++++++-
arch/sh/configs/microdev_defconfig | 410 ++++++++++++++++++++------------
include/asm-sh/microdev.h | 80 ++++++
include/asm-sh/microdev/io.h | 53 ----
include/asm-sh/microdev/irq.h | 72 ------
7 files changed, 583 insertions(+), 394 deletions(-)
create mode 100644 include/asm-sh/microdev.h
delete mode 100644 include/asm-sh/microdev/io.h
delete mode 100644 include/asm-sh/microdev/irq.h
4b4cde7ece5afa9d186ede183d2d865d1cd10758
diff --git a/arch/sh/boards/superh/microdev/io.c b/arch/sh/boards/superh/microdev/io.c
index fe83b2c..1ed7f88 100644
--- a/arch/sh/boards/superh/microdev/io.c
+++ b/arch/sh/boards/superh/microdev/io.c
@@ -16,7 +16,7 @@
#include <linux/pci.h>
#include <linux/wait.h>
#include <asm/io.h>
-#include <asm/mach/io.h>
+#include <asm/microdev.h>
/*
* we need to have a 'safe' address to re-direct all I/O requests
@@ -52,8 +52,90 @@
#define IO_ISP1161_PHYS 0xa7700000ul /* Physical address of Philips ISP1161x USB chip */
#define IO_SUPERIO_PHYS 0xa7800000ul /* Physical address of SMSC FDC37C93xAPM SuperIO chip */
-#define PORT2ADDR(x) (microdev_isa_port2addr(x))
+/*
+ * map I/O ports to memory-mapped addresses
+ */
+static unsigned long microdev_isa_port2addr(unsigned long offset)
+{
+ unsigned long result;
+
+ if ((offset >= IO_LAN91C111_BASE) &&
+ (offset < IO_LAN91C111_BASE + IO_LAN91C111_EXTENT)) {
+ /*
+ * SMSC LAN91C111 Ethernet chip
+ */
+ result = IO_LAN91C111_PHYS + offset - IO_LAN91C111_BASE;
+ } else if ((offset >= IO_SUPERIO_BASE) &&
+ (offset < IO_SUPERIO_BASE + IO_SUPERIO_EXTENT)) {
+ /*
+ * SMSC FDC37C93xAPM SuperIO chip
+ *
+ * Configuration Registers
+ */
+ result = IO_SUPERIO_PHYS + (offset << 1);
+#if 0
+ } else if (offset == KBD_DATA_REG || offset == KBD_CNTL_REG ||
+ offset == KBD_STATUS_REG) {
+ /*
+ * SMSC FDC37C93xAPM SuperIO chip
+ *
+ * PS/2 Keyboard + Mouse (ports 0x60 and 0x64).
+ */
+ result = IO_SUPERIO_PHYS + (offset << 1);
+#endif
+ } else if (((offset >= IO_IDE1_BASE) &&
+ (offset < IO_IDE1_BASE + IO_IDE_EXTENT)) ||
+ (offset == IO_IDE1_MISC)) {
+ /*
+ * SMSC FDC37C93xAPM SuperIO chip
+ *
+ * IDE #1
+ */
+ result = IO_SUPERIO_PHYS + (offset << 1);
+ } else if (((offset >= IO_IDE2_BASE) &&
+ (offset < IO_IDE2_BASE + IO_IDE_EXTENT)) ||
+ (offset == IO_IDE2_MISC)) {
+ /*
+ * SMSC FDC37C93xAPM SuperIO chip
+ *
+ * IDE #2
+ */
+ result = IO_SUPERIO_PHYS + (offset << 1);
+ } else if ((offset >= IO_SERIAL1_BASE) &&
+ (offset < IO_SERIAL1_BASE + IO_SERIAL_EXTENT)) {
+ /*
+ * SMSC FDC37C93xAPM SuperIO chip
+ *
+ * Serial #1
+ */
+ result = IO_SUPERIO_PHYS + (offset << 1);
+ } else if ((offset >= IO_SERIAL2_BASE) &&
+ (offset < IO_SERIAL2_BASE + IO_SERIAL_EXTENT)) {
+ /*
+ * SMSC FDC37C93xAPM SuperIO chip
+ *
+ * Serial #2
+ */
+ result = IO_SUPERIO_PHYS + (offset << 1);
+ } else if ((offset >= IO_ISP1161_BASE) &&
+ (offset < IO_ISP1161_BASE + IO_ISP1161_EXTENT)) {
+ /*
+ * Philips USB ISP1161x chip
+ */
+ result = IO_ISP1161_PHYS + offset - IO_ISP1161_BASE;
+ } else {
+ /*
+ * safe default.
+ */
+ printk("Warning: unexpected port in %s( offset = 0x%lx )\n",
+ __FUNCTION__, offset);
+ result = PVR;
+ }
+
+ return result;
+}
+#define PORT2ADDR(x) (microdev_isa_port2addr(x))
static inline void delay(void)
{
@@ -94,6 +176,17 @@ unsigned int microdev_inl(unsigned long
return *(volatile unsigned int*)PORT2ADDR(port);
}
+void microdev_outw(unsigned short b, unsigned long port)
+{
+#ifdef CONFIG_PCI
+ if (port >= PCIBIOS_MIN_IO) {
+ microdev_pci_outw(b, port);
+ return;
+ }
+#endif
+ *(volatile unsigned short*)PORT2ADDR(port) = b;
+}
+
void microdev_outb(unsigned char b, unsigned long port)
{
#ifdef CONFIG_PCI
@@ -158,17 +251,6 @@ void microdev_outb(unsigned char b, unsi
}
}
-void microdev_outw(unsigned short b, unsigned long port)
-{
-#ifdef CONFIG_PCI
- if (port >= PCIBIOS_MIN_IO) {
- microdev_pci_outw(b, port);
- return;
- }
-#endif
- *(volatile unsigned short*)PORT2ADDR(port) = b;
-}
-
void microdev_outl(unsigned int b, unsigned long port)
{
#ifdef CONFIG_PCI
@@ -284,87 +366,3 @@ void microdev_outsl(unsigned long port,
while (count--)
*port_addr = *buf++;
}
-
-/*
- * map I/O ports to memory-mapped addresses
- */
-unsigned long microdev_isa_port2addr(unsigned long offset)
-{
- unsigned long result;
-
- if ((offset >= IO_LAN91C111_BASE) &&
- (offset < IO_LAN91C111_BASE + IO_LAN91C111_EXTENT)) {
- /*
- * SMSC LAN91C111 Ethernet chip
- */
- result = IO_LAN91C111_PHYS + offset - IO_LAN91C111_BASE;
- } else if ((offset >= IO_SUPERIO_BASE) &&
- (offset < IO_SUPERIO_BASE + IO_SUPERIO_EXTENT)) {
- /*
- * SMSC FDC37C93xAPM SuperIO chip
- *
- * Configuration Registers
- */
- result = IO_SUPERIO_PHYS + (offset << 1);
-#if 0
- } else if (offset == KBD_DATA_REG || offset == KBD_CNTL_REG ||
- offset == KBD_STATUS_REG) {
- /*
- * SMSC FDC37C93xAPM SuperIO chip
- *
- * PS/2 Keyboard + Mouse (ports 0x60 and 0x64).
- */
- result = IO_SUPERIO_PHYS + (offset << 1);
-#endif
- } else if (((offset >= IO_IDE1_BASE) &&
- (offset < IO_IDE1_BASE + IO_IDE_EXTENT)) ||
- (offset == IO_IDE1_MISC)) {
- /*
- * SMSC FDC37C93xAPM SuperIO chip
- *
- * IDE #1
- */
- result = IO_SUPERIO_PHYS + (offset << 1);
- } else if (((offset >= IO_IDE2_BASE) &&
- (offset < IO_IDE2_BASE + IO_IDE_EXTENT)) ||
- (offset == IO_IDE2_MISC)) {
- /*
- * SMSC FDC37C93xAPM SuperIO chip
- *
- * IDE #2
- */
- result = IO_SUPERIO_PHYS + (offset << 1);
- } else if ((offset >= IO_SERIAL1_BASE) &&
- (offset < IO_SERIAL1_BASE + IO_SERIAL_EXTENT)) {
- /*
- * SMSC FDC37C93xAPM SuperIO chip
- *
- * Serial #1
- */
- result = IO_SUPERIO_PHYS + (offset << 1);
- } else if ((offset >= IO_SERIAL2_BASE) &&
- (offset < IO_SERIAL2_BASE + IO_SERIAL_EXTENT)) {
- /*
- * SMSC FDC37C93xAPM SuperIO chip
- *
- * Serial #2
- */
- result = IO_SUPERIO_PHYS + (offset << 1);
- } else if ((offset >= IO_ISP1161_BASE) &&
- (offset < IO_ISP1161_BASE + IO_ISP1161_EXTENT)) {
- /*
- * Philips USB ISP1161x chip
- */
- result = IO_ISP1161_PHYS + offset - IO_ISP1161_BASE;
- } else {
- /*
- * safe default.
- */
- printk("Warning: unexpected port in %s( offset = 0x%lx )\n",
- __FUNCTION__, offset);
- result = PVR;
- }
-
- return result;
-}
-
diff --git a/arch/sh/boards/superh/microdev/irq.c b/arch/sh/boards/superh/microdev/irq.c
index 1395c1e..efcbd86 100644
--- a/arch/sh/boards/superh/microdev/irq.c
+++ b/arch/sh/boards/superh/microdev/irq.c
@@ -15,7 +15,7 @@
#include <asm/system.h>
#include <asm/io.h>
-#include <asm/mach/irq.h>
+#include <asm/microdev.h>
#define NUM_EXTERNAL_IRQS 16 /* IRL0 .. IRL15 */
diff --git a/arch/sh/boards/superh/microdev/setup.c b/arch/sh/boards/superh/microdev/setup.c
index 1c1d65f..bf0b381 100644
--- a/arch/sh/boards/superh/microdev/setup.c
+++ b/arch/sh/boards/superh/microdev/setup.c
@@ -3,7 +3,7 @@
*
* Copyright (C) 2003 Sean McGoogan ([email protected])
* Copyright (C) 2003, 2004 SuperH, Inc.
- * Copyright (C) 2004 Paul Mundt
+ * Copyright (C) 2004, 2005 Paul Mundt
*
* SuperH SH4-202 MicroDev board support.
*
@@ -15,11 +15,10 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ioport.h>
+#include <video/s1d13xxxfb.h>
+#include <asm/microdev.h>
#include <asm/io.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/io.h>
#include <asm/machvec.h>
-#include <asm/machvec_init.h>
extern void microdev_heartbeat(void);
@@ -51,8 +50,6 @@ struct sh_machine_vector mv_sh4202_micro
.mv_outsw = microdev_outsw,
.mv_outsl = microdev_outsl,
- .mv_isa_port2addr = microdev_isa_port2addr,
-
.mv_init_irq = init_microdev_irq,
#ifdef CONFIG_HEARTBEAT
@@ -142,16 +139,161 @@ static struct platform_device smc91x_dev
.resource = smc91x_resources,
};
-static int __init smc91x_setup(void)
+#ifdef CONFIG_FB_S1D13XXX
+static struct s1d13xxxfb_regval s1d13806_initregs[] = {
+ { S1DREG_MISC, 0x00 },
+ { S1DREG_COM_DISP_MODE, 0x00 },
+ { S1DREG_GPIO_CNF0, 0x00 },
+ { S1DREG_GPIO_CNF1, 0x00 },
+ { S1DREG_GPIO_CTL0, 0x00 },
+ { S1DREG_GPIO_CTL1, 0x00 },
+ { S1DREG_CLK_CNF, 0x02 },
+ { S1DREG_LCD_CLK_CNF, 0x01 },
+ { S1DREG_CRT_CLK_CNF, 0x03 },
+ { S1DREG_MPLUG_CLK_CNF, 0x03 },
+ { S1DREG_CPU2MEM_WST_SEL, 0x02 },
+ { S1DREG_SDRAM_REF_RATE, 0x03 },
+ { S1DREG_SDRAM_TC0, 0x00 },
+ { S1DREG_SDRAM_TC1, 0x01 },
+ { S1DREG_MEM_CNF, 0x80 },
+ { S1DREG_PANEL_TYPE, 0x25 },
+ { S1DREG_MOD_RATE, 0x00 },
+ { S1DREG_LCD_DISP_HWIDTH, 0x63 },
+ { S1DREG_LCD_NDISP_HPER, 0x1e },
+ { S1DREG_TFT_FPLINE_START, 0x06 },
+ { S1DREG_TFT_FPLINE_PWIDTH, 0x03 },
+ { S1DREG_LCD_DISP_VHEIGHT0, 0x57 },
+ { S1DREG_LCD_DISP_VHEIGHT1, 0x02 },
+ { S1DREG_LCD_NDISP_VPER, 0x00 },
+ { S1DREG_TFT_FPFRAME_START, 0x0a },
+ { S1DREG_TFT_FPFRAME_PWIDTH, 0x81 },
+ { S1DREG_LCD_DISP_MODE, 0x03 },
+ { S1DREG_LCD_MISC, 0x00 },
+ { S1DREG_LCD_DISP_START0, 0x00 },
+ { S1DREG_LCD_DISP_START1, 0x00 },
+ { S1DREG_LCD_DISP_START2, 0x00 },
+ { S1DREG_LCD_MEM_OFF0, 0x90 },
+ { S1DREG_LCD_MEM_OFF1, 0x01 },
+ { S1DREG_LCD_PIX_PAN, 0x00 },
+ { S1DREG_LCD_DISP_FIFO_HTC, 0x00 },
+ { S1DREG_LCD_DISP_FIFO_LTC, 0x00 },
+ { S1DREG_CRT_DISP_HWIDTH, 0x63 },
+ { S1DREG_CRT_NDISP_HPER, 0x1f },
+ { S1DREG_CRT_HRTC_START, 0x04 },
+ { S1DREG_CRT_HRTC_PWIDTH, 0x8f },
+ { S1DREG_CRT_DISP_VHEIGHT0, 0x57 },
+ { S1DREG_CRT_DISP_VHEIGHT1, 0x02 },
+ { S1DREG_CRT_NDISP_VPER, 0x1b },
+ { S1DREG_CRT_VRTC_START, 0x00 },
+ { S1DREG_CRT_VRTC_PWIDTH, 0x83 },
+ { S1DREG_TV_OUT_CTL, 0x10 },
+ { S1DREG_CRT_DISP_MODE, 0x05 },
+ { S1DREG_CRT_DISP_START0, 0x00 },
+ { S1DREG_CRT_DISP_START1, 0x00 },
+ { S1DREG_CRT_DISP_START2, 0x00 },
+ { S1DREG_CRT_MEM_OFF0, 0x20 },
+ { S1DREG_CRT_MEM_OFF1, 0x03 },
+ { S1DREG_CRT_PIX_PAN, 0x00 },
+ { S1DREG_CRT_DISP_FIFO_HTC, 0x00 },
+ { S1DREG_CRT_DISP_FIFO_LTC, 0x00 },
+ { S1DREG_LCD_CUR_CTL, 0x00 },
+ { S1DREG_LCD_CUR_START, 0x01 },
+ { S1DREG_LCD_CUR_XPOS0, 0x00 },
+ { S1DREG_LCD_CUR_XPOS1, 0x00 },
+ { S1DREG_LCD_CUR_YPOS0, 0x00 },
+ { S1DREG_LCD_CUR_YPOS1, 0x00 },
+ { S1DREG_LCD_CUR_BCTL0, 0x00 },
+ { S1DREG_LCD_CUR_GCTL0, 0x00 },
+ { S1DREG_LCD_CUR_RCTL0, 0x00 },
+ { S1DREG_LCD_CUR_BCTL1, 0x1f },
+ { S1DREG_LCD_CUR_GCTL1, 0x3f },
+ { S1DREG_LCD_CUR_RCTL1, 0x1f },
+ { S1DREG_LCD_CUR_FIFO_HTC, 0x00 },
+ { S1DREG_CRT_CUR_CTL, 0x00 },
+ { S1DREG_CRT_CUR_START, 0x01 },
+ { S1DREG_CRT_CUR_XPOS0, 0x00 },
+ { S1DREG_CRT_CUR_XPOS1, 0x00 },
+ { S1DREG_CRT_CUR_YPOS0, 0x00 },
+ { S1DREG_CRT_CUR_YPOS1, 0x00 },
+ { S1DREG_CRT_CUR_BCTL0, 0x00 },
+ { S1DREG_CRT_CUR_GCTL0, 0x00 },
+ { S1DREG_CRT_CUR_RCTL0, 0x00 },
+ { S1DREG_CRT_CUR_BCTL1, 0x1f },
+ { S1DREG_CRT_CUR_GCTL1, 0x3f },
+ { S1DREG_CRT_CUR_RCTL1, 0x1f },
+ { S1DREG_CRT_CUR_FIFO_HTC, 0x00 },
+ { S1DREG_BBLT_CTL0, 0x00 },
+ { S1DREG_BBLT_CTL1, 0x00 },
+ { S1DREG_BBLT_CC_EXP, 0x00 },
+ { S1DREG_BBLT_OP, 0x00 },
+ { S1DREG_BBLT_SRC_START0, 0x00 },
+ { S1DREG_BBLT_SRC_START1, 0x00 },
+ { S1DREG_BBLT_SRC_START2, 0x00 },
+ { S1DREG_BBLT_DST_START0, 0x00 },
+ { S1DREG_BBLT_DST_START1, 0x00 },
+ { S1DREG_BBLT_DST_START2, 0x00 },
+ { S1DREG_BBLT_MEM_OFF0, 0x00 },
+ { S1DREG_BBLT_MEM_OFF1, 0x00 },
+ { S1DREG_BBLT_WIDTH0, 0x00 },
+ { S1DREG_BBLT_WIDTH1, 0x00 },
+ { S1DREG_BBLT_HEIGHT0, 0x00 },
+ { S1DREG_BBLT_HEIGHT1, 0x00 },
+ { S1DREG_BBLT_BGC0, 0x00 },
+ { S1DREG_BBLT_BGC1, 0x00 },
+ { S1DREG_BBLT_FGC0, 0x00 },
+ { S1DREG_BBLT_FGC1, 0x00 },
+ { S1DREG_LKUP_MODE, 0x00 },
+ { S1DREG_LKUP_ADDR, 0x00 },
+ { S1DREG_PS_CNF, 0x10 },
+ { S1DREG_PS_STATUS, 0x00 },
+ { S1DREG_CPU2MEM_WDOGT, 0x00 },
+ { S1DREG_COM_DISP_MODE, 0x02 },
+};
+
+static struct s1d13xxxfb_pdata s1d13806_platform_data = {
+ .initregs = s1d13806_initregs,
+ .initregssize = ARRAY_SIZE(s1d13806_initregs),
+};
+
+static struct resource s1d13806_resources[] = {
+ [0] = {
+ .start = 0x07200000,
+ .end = 0x07200000 + 0x00200000 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = 0x07000000,
+ .end = 0x07000000 + 0x00200000 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device s1d13806_device = {
+ .name = "s1d13806fb",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(s1d13806_resources),
+ .resource = s1d13806_resources,
+
+ .dev = {
+ .platform_data = &s1d13806_platform_data,
+ },
+};
+#endif
+
+static struct platform_device *microdev_devices[] __initdata = {
+ &smc91x_device,
+#ifdef CONFIG_FB_S1D13XXX
+ &s1d13806_device,
+#endif
+};
+
+static int __init microdev_devices_setup(void)
{
- return platform_device_register(&smc91x_device);
+ return platform_add_devices(microdev_devices, ARRAY_SIZE(microdev_devices));
}
-__initcall(smc91x_setup);
+__initcall(microdev_devices_setup);
- /*
- * Initialize the board
- */
void __init platform_setup(void)
{
int * const fpgaRevisionRegister = (int*)(MICRODEV_FPGA_GP_BASE + 0x8ul);
@@ -256,7 +398,7 @@ static int __init smsc_superio_setup(voi
/* enable the appropriate GPIO pins for IDE functionality:
* bit[0] In/Out 1==input; 0==output
* bit[1] Polarity 1==invert; 0==no invert
- * bit[2] Int Enb #1 1==Enable Combined IRQ #1; 0==disable
+ * bit[2] Int Enb #1 1==Enable Combined IRQ #1; 0==disable
* bit[3:4] Function Select 00==original; 01==Alternate Function #1
*/
SMSC_WRITE_INDEXED(0x00, 0xc2); /* GP42 = nIDE1_OE */
diff --git a/arch/sh/configs/microdev_defconfig b/arch/sh/configs/microdev_defconfig
index a3bd280..ab3db76 100644
--- a/arch/sh/configs/microdev_defconfig
+++ b/arch/sh/configs/microdev_defconfig
@@ -1,10 +1,9 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.11-sh
-# Wed Mar 2 15:09:41 2005
+# Linux kernel version: 2.6.16-rc1
+# Fri Jan 27 19:43:20 2006
#
CONFIG_SUPERH=y
-CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
@@ -17,11 +16,13 @@ CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
# CONFIG_SYSVIPC is not set
# CONFIG_POSIX_MQUEUE is not set
@@ -29,22 +30,29 @@ CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_HOTPLUG=y
-CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_UID16=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
+CONFIG_SLAB=y
# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
#
# Loadable module support
@@ -52,6 +60,24 @@ CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_MODULES is not set
#
+# Block layer
+#
+# CONFIG_LBD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
# System type
#
# CONFIG_SH_SOLUTION_ENGINE is not set
@@ -61,9 +87,7 @@ CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_SH_7751_SYSTEMH is not set
# CONFIG_SH_STB1_HARP is not set
# CONFIG_SH_STB1_OVERDRIVE is not set
-# CONFIG_SH_HP620 is not set
-# CONFIG_SH_HP680 is not set
-# CONFIG_SH_HP690 is not set
+# CONFIG_SH_HP6XX is not set
# CONFIG_SH_CQREEK is not set
# CONFIG_SH_DMIDA is not set
# CONFIG_SH_EC3104 is not set
@@ -78,45 +102,94 @@ CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_SH_SECUREEDGE5410 is not set
# CONFIG_SH_HS7751RVOIP is not set
# CONFIG_SH_RTS7751R2D is not set
+# CONFIG_SH_R7780RP is not set
# CONFIG_SH_EDOSK7705 is not set
CONFIG_SH_SH4202_MICRODEV=y
+# CONFIG_SH_LANDISK is not set
+# CONFIG_SH_TITAN is not set
# CONFIG_SH_UNKNOWN is not set
-# CONFIG_CPU_SH2 is not set
-# CONFIG_CPU_SH3 is not set
+
+#
+# Processor selection
+#
CONFIG_CPU_SH4=y
+
+#
+# SH-2 Processor Support
+#
# CONFIG_CPU_SUBTYPE_SH7604 is not set
+
+#
+# SH-3 Processor Support
+#
# CONFIG_CPU_SUBTYPE_SH7300 is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7708 is not set
# CONFIG_CPU_SUBTYPE_SH7709 is not set
+
+#
+# SH-4 Processor Support
+#
# CONFIG_CPU_SUBTYPE_SH7750 is not set
+# CONFIG_CPU_SUBTYPE_SH7091 is not set
+# CONFIG_CPU_SUBTYPE_SH7750R is not set
+# CONFIG_CPU_SUBTYPE_SH7750S is not set
# CONFIG_CPU_SUBTYPE_SH7751 is not set
+# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
-# CONFIG_CPU_SUBTYPE_SH73180 is not set
+CONFIG_CPU_SUBTYPE_SH4_202=y
+
+#
+# ST40 Processor Support
+#
# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
-CONFIG_CPU_SUBTYPE_SH4_202=y
+
+#
+# SH-4A Processor Support
+#
+# CONFIG_CPU_SUBTYPE_SH73180 is not set
+# CONFIG_CPU_SUBTYPE_SH7770 is not set
+# CONFIG_CPU_SUBTYPE_SH7780 is not set
+
+#
+# Memory management options
+#
CONFIG_MMU=y
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE="console=ttySC0,115200"
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+
+#
+# Cache configuration
+#
+# CONFIG_SH_DIRECT_MAPPED is not set
+# CONFIG_SH_WRITETHROUGH is not set
+# CONFIG_SH_OCRAM is not set
CONFIG_MEMORY_START=0x08000000
CONFIG_MEMORY_SIZE=0x04000000
-CONFIG_MEMORY_SET=y
-# CONFIG_MEMORY_OVERRIDE is not set
+
+#
+# Processor features
+#
+CONFIG_CPU_LITTLE_ENDIAN=y
CONFIG_SH_RTC=y
CONFIG_SH_FPU=y
-CONFIG_ZERO_PAGE_OFFSET=0x00001000
-CONFIG_BOOT_LINK_OFFSET=0x00800000
-CONFIG_CPU_LITTLE_ENDIAN=y
-CONFIG_PREEMPT=y
-# CONFIG_UBC_WAKEUP is not set
-# CONFIG_SH_WRITETHROUGH is not set
-# CONFIG_SH_OCRAM is not set
# CONFIG_SH_STORE_QUEUES is not set
-# CONFIG_SMP is not set
-CONFIG_SH_PCLK_CALC=y
-CONFIG_SH_PCLK_FREQ=65986048
+CONFIG_CPU_HAS_INTEVT=y
+CONFIG_CPU_HAS_SR_RB=y
+
+#
+# Timer support
+#
+CONFIG_SH_TMU=y
+CONFIG_SH_PCLK_FREQ=66000000
#
# CPU Frequency scaling
@@ -137,20 +210,31 @@ CONFIG_NR_ONCHIP_DMA_CHANNELS=4
CONFIG_HEARTBEAT=y
#
-# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
+# Kernel features
#
-CONFIG_ISA=y
-# CONFIG_PCI is not set
+# CONFIG_KEXEC is not set
+CONFIG_PREEMPT=y
+# CONFIG_SMP is not set
#
-# PCCARD (PCMCIA/CardBus) support
+# Boot options
#
-# CONFIG_PCCARD is not set
+CONFIG_ZERO_PAGE_OFFSET=0x00001000
+CONFIG_BOOT_LINK_OFFSET=0x00800000
+# CONFIG_UBC_WAKEUP is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="console=ttySC0,115200"
#
-# PC-card bridges
+# Bus options
#
-CONFIG_PCMCIA_PROBE=y
+# CONFIG_SUPERHYWAY is not set
+# CONFIG_PCI is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
#
# PCI Hotplug Support
@@ -164,9 +248,79 @@ CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
#
-# SH initrd options
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_PACKET is not set
+# CONFIG_UNIX is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
#
-# CONFIG_EMBEDDED_RAMDISK is not set
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
#
# Device Drivers
@@ -180,6 +334,11 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
@@ -192,13 +351,10 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
#
# Plug and Play support
#
-# CONFIG_PNP is not set
#
# Block devices
#
-# CONFIG_BLK_DEV_FD is not set
-# CONFIG_BLK_DEV_XD is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
@@ -206,17 +362,7 @@ CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE=""
-# CONFIG_LBD is not set
# CONFIG_CDROM_PKTCDVD is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
# CONFIG_ATA_OVER_ETH is not set
#
@@ -241,9 +387,7 @@ CONFIG_BLK_DEV_IDECD=y
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
-CONFIG_IDE_SH=y
# CONFIG_IDE_ARM is not set
-# CONFIG_IDE_CHIPSETS is not set
# CONFIG_BLK_DEV_IDEDMA is not set
# CONFIG_IDEDMA_AUTO is not set
# CONFIG_BLK_DEV_HD is not set
@@ -251,14 +395,10 @@ CONFIG_IDE_SH=y
#
# SCSI device support
#
+# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
#
-# Old CD-ROM drivers (not SCSI, not IDE)
-#
-# CONFIG_CD_NO_IDESCSI is not set
-
-#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
@@ -266,6 +406,7 @@ CONFIG_IDE_SH=y
#
# Fusion MPT device support
#
+# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
@@ -276,69 +417,8 @@ CONFIG_IDE_SH=y
#
#
-# Networking support
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-# CONFIG_PACKET is not set
-# CONFIG_NETLINK_DEV is not set
-# CONFIG_UNIX is not set
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_IP_TCPDIAG=y
-# CONFIG_IP_TCPDIAG_IPV6 is not set
-# CONFIG_IPV6 is not set
-# CONFIG_NETFILTER is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-# CONFIG_NET_CLS_ROUTE is not set
-
-#
-# Network testing
+# Network device support
#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
@@ -346,9 +426,9 @@ CONFIG_NETDEVICES=y
# CONFIG_TUN is not set
#
-# ARCnet devices
+# PHY device support
#
-# CONFIG_ARCNET is not set
+# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
@@ -356,17 +436,7 @@ CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_STNIC is not set
-# CONFIG_NET_VENDOR_3COM is not set
-# CONFIG_LANCE is not set
-# CONFIG_NET_VENDOR_SMC is not set
CONFIG_SMC91X=y
-# CONFIG_NET_VENDOR_RACAL is not set
-# CONFIG_AT1700 is not set
-# CONFIG_DEPCA is not set
-# CONFIG_HP100 is not set
-# CONFIG_NET_ISA is not set
-# CONFIG_NET_PCI is not set
-# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
@@ -379,7 +449,6 @@ CONFIG_SMC91X=y
#
# Token Ring devices
#
-# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
@@ -394,6 +463,8 @@ CONFIG_SMC91X=y
# CONFIG_SLIP is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
@@ -411,20 +482,10 @@ CONFIG_SMC91X=y
# CONFIG_INPUT is not set
#
-# Userland interfaces
-#
-
-#
-# Input I/O drivers
+# Hardware I/O ports
#
-# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
# CONFIG_SERIO is not set
-# CONFIG_SERIO_I8042 is not set
-
-#
-# Input Device Drivers
-#
+# CONFIG_GAMEPORT is not set
#
# Character devices
@@ -464,24 +525,46 @@ CONFIG_RTC=y
#
# Ftape, the floppy tape device driver
#
-# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
# I2C support
#
# CONFIG_I2C is not set
#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
# Misc devices
#
#
+# Multimedia Capabilities Port drivers
+#
+
+#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
@@ -508,7 +591,7 @@ CONFIG_RTC=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
@@ -524,13 +607,21 @@ CONFIG_RTC=y
#
# InfiniBand support
#
-# CONFIG_INFINIBAND is not set
+
+#
+# SN Devices
+#
+
+#
+# EDAC - error detection and reporting (RAS)
+#
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
@@ -540,17 +631,17 @@ CONFIG_JBD=y
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
-
-#
-# XFS support
-#
+# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
@@ -574,16 +665,12 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
-CONFIG_DEVFS_FS=y
-CONFIG_DEVFS_MOUNT=y
-# CONFIG_DEVFS_DEBUG is not set
-CONFIG_DEVPTS_FS_XATTR=y
-# CONFIG_DEVPTS_FS_SECURITY is not set
CONFIG_TMPFS=y
-# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
+# CONFIG_RELAYFS_FS is not set
+# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
@@ -607,12 +694,14 @@ CONFIG_RAMFS=y
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_RPCSEC_GSS_KRB5=y
@@ -622,6 +711,7 @@ CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
#
# Partition Types
@@ -681,8 +771,10 @@ CONFIG_NLS_DEFAULT="iso8859-1"
#
# Kernel hacking
#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_DEBUG_PREEMPT=y
+CONFIG_LOG_BUF_SHIFT=14
# CONFIG_FRAME_POINTER is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
@@ -706,6 +798,7 @@ CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
@@ -730,5 +823,6 @@ CONFIG_CRYPTO_DES=y
# Library routines
#
# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
diff --git a/include/asm-sh/microdev.h b/include/asm-sh/microdev.h
new file mode 100644
index 0000000..018332a
--- /dev/null
+++ b/include/asm-sh/microdev.h
@@ -0,0 +1,80 @@
+/*
+ * linux/include/asm-sh/microdev.h
+ *
+ * Copyright (C) 2003 Sean McGoogan ([email protected])
+ *
+ * Definitions for the SuperH SH4-202 MicroDev board.
+ *
+ * May be copied or modified under the terms of the GNU General Public
+ * License. See linux/COPYING for more information.
+ */
+#ifndef __ASM_SH_MICRODEV_H
+#define __ASM_SH_MICRODEV_H
+
+extern void init_microdev_irq(void);
+extern void microdev_print_fpga_intc_status(void);
+
+/*
+ * The following are useful macros for manipulating the interrupt
+ * controller (INTC) on the CPU-board FPGA. should be noted that there
+ * is an INTC on the FPGA, and a seperate INTC on the SH4-202 core -
+ * these are two different things, both of which need to be prorammed to
+ * correctly route - unfortunately, they have the same name and
+ * abbreviations!
+ */
+#define MICRODEV_FPGA_INTC_BASE 0xa6110000ul /* INTC base address on CPU-board FPGA */
+#define MICRODEV_FPGA_INTENB_REG (MICRODEV_FPGA_INTC_BASE+0ul) /* Interrupt Enable Register on INTC on CPU-board FPGA */
+#define MICRODEV_FPGA_INTDSB_REG (MICRODEV_FPGA_INTC_BASE+8ul) /* Interrupt Disable Register on INTC on CPU-board FPGA */
+#define MICRODEV_FPGA_INTC_MASK(n) (1ul<<(n)) /* Interupt mask to enable/disable INTC in CPU-board FPGA */
+#define MICRODEV_FPGA_INTPRI_REG(n) (MICRODEV_FPGA_INTC_BASE+0x10+((n)/8)*8)/* Interrupt Priority Register on INTC on CPU-board FPGA */
+#define MICRODEV_FPGA_INTPRI_LEVEL(n,x) ((x)<<(((n)%8)*4)) /* MICRODEV_FPGA_INTPRI_LEVEL(int_number, int_level) */
+#define MICRODEV_FPGA_INTPRI_MASK(n) (MICRODEV_FPGA_INTPRI_LEVEL((n),0xful)) /* Interrupt Priority Mask on INTC on CPU-board FPGA */
+#define MICRODEV_FPGA_INTSRC_REG (MICRODEV_FPGA_INTC_BASE+0x30ul) /* Interrupt Source Register on INTC on CPU-board FPGA */
+#define MICRODEV_FPGA_INTREQ_REG (MICRODEV_FPGA_INTC_BASE+0x38ul) /* Interrupt Request Register on INTC on CPU-board FPGA */
+
+
+/*
+ * The following are the IRQ numbers for the Linux Kernel for external
+ * interrupts. i.e. the numbers seen by 'cat /proc/interrupt'.
+ */
+#define MICRODEV_LINUX_IRQ_KEYBOARD 1 /* SuperIO Keyboard */
+#define MICRODEV_LINUX_IRQ_SERIAL1 2 /* SuperIO Serial #1 */
+#define MICRODEV_LINUX_IRQ_ETHERNET 3 /* on-board Ethnernet */
+#define MICRODEV_LINUX_IRQ_SERIAL2 4 /* SuperIO Serial #2 */
+#define MICRODEV_LINUX_IRQ_USB_HC 7 /* on-board USB HC */
+#define MICRODEV_LINUX_IRQ_MOUSE 12 /* SuperIO PS/2 Mouse */
+#define MICRODEV_LINUX_IRQ_IDE2 13 /* SuperIO IDE #2 */
+#define MICRODEV_LINUX_IRQ_IDE1 14 /* SuperIO IDE #1 */
+
+/*
+ * The following are the IRQ numbers for the INTC on the FPGA for
+ * external interrupts. i.e. the bits in the INTC registers in the
+ * FPGA.
+ */
+#define MICRODEV_FPGA_IRQ_KEYBOARD 1 /* SuperIO Keyboard */
+#define MICRODEV_FPGA_IRQ_SERIAL1 3 /* SuperIO Serial #1 */
+#define MICRODEV_FPGA_IRQ_SERIAL2 4 /* SuperIO Serial #2 */
+#define MICRODEV_FPGA_IRQ_MOUSE 12 /* SuperIO PS/2 Mouse */
+#define MICRODEV_FPGA_IRQ_IDE1 14 /* SuperIO IDE #1 */
+#define MICRODEV_FPGA_IRQ_IDE2 15 /* SuperIO IDE #2 */
+#define MICRODEV_FPGA_IRQ_USB_HC 16 /* on-board USB HC */
+#define MICRODEV_FPGA_IRQ_ETHERNET 18 /* on-board Ethnernet */
+
+#define MICRODEV_IRQ_PCI_INTA 8
+#define MICRODEV_IRQ_PCI_INTB 9
+#define MICRODEV_IRQ_PCI_INTC 10
+#define MICRODEV_IRQ_PCI_INTD 11
+
+#define __IO_PREFIX microdev
+#include <asm/io_generic.h>
+
+#if defined(CONFIG_PCI)
+unsigned char microdev_pci_inb(unsigned long port);
+unsigned short microdev_pci_inw(unsigned long port);
+unsigned long microdev_pci_inl(unsigned long port);
+void microdev_pci_outb(unsigned char data, unsigned long port);
+void microdev_pci_outw(unsigned short data, unsigned long port);
+void microdev_pci_outl(unsigned long data, unsigned long port);
+#endif
+
+#endif /* __ASM_SH_MICRODEV_H */
diff --git a/include/asm-sh/microdev/io.h b/include/asm-sh/microdev/io.h
deleted file mode 100644
index f2ca4ac..0000000
--- a/include/asm-sh/microdev/io.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * linux/include/asm-sh/io_microdev.h
- *
- * Copyright (C) 2003 Sean McGoogan ([email protected])
- *
- * IO functions for the SuperH SH4-202 MicroDev board.
- *
- * May be copied or modified under the terms of the GNU General Public
- * License. See linux/COPYING for more information.
- *
- */
-
-
-#ifndef _ASM_SH_IO_MICRODEV_H
-#define _ASM_SH_IO_MICRODEV_H
-
-extern unsigned long microdev_isa_port2addr(unsigned long offset);
-
-extern unsigned char microdev_inb(unsigned long port);
-extern unsigned short microdev_inw(unsigned long port);
-extern unsigned int microdev_inl(unsigned long port);
-
-extern void microdev_outb(unsigned char value, unsigned long port);
-extern void microdev_outw(unsigned short value, unsigned long port);
-extern void microdev_outl(unsigned int value, unsigned long port);
-
-extern unsigned char microdev_inb_p(unsigned long port);
-extern unsigned short microdev_inw_p(unsigned long port);
-extern unsigned int microdev_inl_p(unsigned long port);
-
-extern void microdev_outb_p(unsigned char value, unsigned long port);
-extern void microdev_outw_p(unsigned short value, unsigned long port);
-extern void microdev_outl_p(unsigned int value, unsigned long port);
-
-extern void microdev_insb(unsigned long port, void *addr, unsigned long count);
-extern void microdev_insw(unsigned long port, void *addr, unsigned long count);
-extern void microdev_insl(unsigned long port, void *addr, unsigned long count);
-
-extern void microdev_outsb(unsigned long port, const void *addr, unsigned long count);
-extern void microdev_outsw(unsigned long port, const void *addr, unsigned long count);
-extern void microdev_outsl(unsigned long port, const void *addr, unsigned long count);
-
-#if defined(CONFIG_PCI)
-extern unsigned char microdev_pci_inb(unsigned long port);
-extern unsigned short microdev_pci_inw(unsigned long port);
-extern unsigned long microdev_pci_inl(unsigned long port);
-extern void microdev_pci_outb(unsigned char data, unsigned long port);
-extern void microdev_pci_outw(unsigned short data, unsigned long port);
-extern void microdev_pci_outl(unsigned long data, unsigned long port);
-#endif
-
-#endif /* _ASM_SH_IO_MICRODEV_H */
-
diff --git a/include/asm-sh/microdev/irq.h b/include/asm-sh/microdev/irq.h
deleted file mode 100644
index 47f6f77..0000000
--- a/include/asm-sh/microdev/irq.h
+++ /dev/null
@@ -1,72 +0,0 @@
-/*
- * linux/include/asm-sh/irq_microdev.h
- *
- * Copyright (C) 2003 Sean McGoogan ([email protected])
- *
- * IRQ functions for the SuperH SH4-202 MicroDev board.
- *
- * May be copied or modified under the terms of the GNU General Public
- * License. See linux/COPYING for more information.
- *
- */
-
-
-#ifndef _ASM_SH_IRQ_MICRODEV_H
-#define _ASM_SH_IRQ_MICRODEV_H
-
-extern void init_microdev_irq(void);
-extern void microdev_print_fpga_intc_status(void);
-
-
- /*
- * The following are useful macros for manipulating the
- * interrupt controller (INTC) on the CPU-board FPGA.
- * It should be noted that there is an INTC on the FPGA,
- * and a seperate INTC on the SH4-202 core - these are
- * two different things, both of which need to be prorammed
- * to correctly route - unfortunately, they have the
- * same name and abbreviations!
- */
-#define MICRODEV_FPGA_INTC_BASE 0xa6110000ul /* INTC base address on CPU-board FPGA */
-#define MICRODEV_FPGA_INTENB_REG (MICRODEV_FPGA_INTC_BASE+0ul) /* Interrupt Enable Register on INTC on CPU-board FPGA */
-#define MICRODEV_FPGA_INTDSB_REG (MICRODEV_FPGA_INTC_BASE+8ul) /* Interrupt Disable Register on INTC on CPU-board FPGA */
-#define MICRODEV_FPGA_INTC_MASK(n) (1ul<<(n)) /* Interupt mask to enable/disable INTC in CPU-board FPGA */
-#define MICRODEV_FPGA_INTPRI_REG(n) (MICRODEV_FPGA_INTC_BASE+0x10+((n)/8)*8)/* Interrupt Priority Register on INTC on CPU-board FPGA */
-#define MICRODEV_FPGA_INTPRI_LEVEL(n,x) ((x)<<(((n)%8)*4)) /* MICRODEV_FPGA_INTPRI_LEVEL(int_number, int_level) */
-#define MICRODEV_FPGA_INTPRI_MASK(n) (MICRODEV_FPGA_INTPRI_LEVEL((n),0xful)) /* Interrupt Priority Mask on INTC on CPU-board FPGA */
-#define MICRODEV_FPGA_INTSRC_REG (MICRODEV_FPGA_INTC_BASE+0x30ul) /* Interrupt Source Register on INTC on CPU-board FPGA */
-#define MICRODEV_FPGA_INTREQ_REG (MICRODEV_FPGA_INTC_BASE+0x38ul) /* Interrupt Request Register on INTC on CPU-board FPGA */
-
-
- /*
- * The following are the IRQ numbers for the Linux Kernel for external interrupts.
- * i.e. the numbers seen by 'cat /proc/interrupt'.
- */
-#define MICRODEV_LINUX_IRQ_KEYBOARD 1 /* SuperIO Keyboard */
-#define MICRODEV_LINUX_IRQ_SERIAL1 2 /* SuperIO Serial #1 */
-#define MICRODEV_LINUX_IRQ_ETHERNET 3 /* on-board Ethnernet */
-#define MICRODEV_LINUX_IRQ_SERIAL2 4 /* SuperIO Serial #2 */
-#define MICRODEV_LINUX_IRQ_USB_HC 7 /* on-board USB HC */
-#define MICRODEV_LINUX_IRQ_MOUSE 12 /* SuperIO PS/2 Mouse */
-#define MICRODEV_LINUX_IRQ_IDE2 13 /* SuperIO IDE #2 */
-#define MICRODEV_LINUX_IRQ_IDE1 14 /* SuperIO IDE #1 */
-
- /*
- * The following are the IRQ numbers for the INTC on the FPGA for external interrupts.
- * i.e. the bits in the INTC registers in the FPGA.
- */
-#define MICRODEV_FPGA_IRQ_KEYBOARD 1 /* SuperIO Keyboard */
-#define MICRODEV_FPGA_IRQ_SERIAL1 3 /* SuperIO Serial #1 */
-#define MICRODEV_FPGA_IRQ_SERIAL2 4 /* SuperIO Serial #2 */
-#define MICRODEV_FPGA_IRQ_MOUSE 12 /* SuperIO PS/2 Mouse */
-#define MICRODEV_FPGA_IRQ_IDE1 14 /* SuperIO IDE #1 */
-#define MICRODEV_FPGA_IRQ_IDE2 15 /* SuperIO IDE #2 */
-#define MICRODEV_FPGA_IRQ_USB_HC 16 /* on-board USB HC */
-#define MICRODEV_FPGA_IRQ_ETHERNET 18 /* on-board Ethnernet */
-
-#define MICRODEV_IRQ_PCI_INTA 8
-#define MICRODEV_IRQ_PCI_INTB 9
-#define MICRODEV_IRQ_PCI_INTC 10
-#define MICRODEV_IRQ_PCI_INTD 11
-
-#endif /* _ASM_SH_IRQ_MICRODEV_H */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
