Hi.
On Thursday 26 January 2006 18:00, Prakash Punnoor wrote:
> Hi,
>
> I have some problems with the uli526x driver. (I cc'ed the tulip
> maintainer, as the driver is found in this category.)
>
> - It doesn't detect link when cable is plugged in, if module/driver is
> loaded with no cable attached. I have to rmmod the module, plug in cable,
> insmod the module and then set up the interface to get it running. That's
> the only reason I compiled this driver as a module...(BTW, it is not AMD64
> related, as I experienced this also in x86.)
>
> - dhcpcd doesn't work. dhclient does though (but it is slow, I can't find
> the correct parameters to speed it up). The former gets no response from
> the dhcp server. I don't think it is a problem with the dhcp server, as
> dhcpcd works from a notebook with some dlink pcmcia 10mbit interface.
>
>
> Beside above, it seems to work fine, though.
I have one too, and have done some work toward implementing power management
support (working, but needs further work). I've noticed the link issue and
will see if I can address it too. Regarding dhcpcd, I haven't used it, but
will see if I can test before sending the patches to Jeff and to Peer Chen.
Regards,
Nigel
>
> attached some infos which might be needed:
>
> Bootdata ok (command line is root=/dev/sda5 elevator=cfq quiet)
> Linux version 2.6.15 (root@varma) (gcc-Version 3.4.5 (Gentoo 3.4.5)) #1 SMP
> PREEMPT Thu Jan 12 14:50:12 CET 2006
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
> BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data)
> BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS)
> BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
> BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
> BIOS-e820: 0000000100000000 - 0000000180000000 (usable)
> ACPI: RSDP (v000 ACPIAM ) @
> 0x00000000000f9bb0 ACPI: RSDT (v001 A M I OEMRSDT 0x12000506 MSFT
> 0x00000097) @
> 0x000000007ffb0000
> ACPI: FADT (v002 A M I OEMFACP 0x12000506 MSFT 0x00000097) @
> 0x000000007ffb0200
> ACPI: MADT (v001 A M I OEMAPIC 0x12000506 MSFT 0x00000097) @
> 0x000000007ffb0390
> ACPI: OEMB (v001 A M I AMI_OEM 0x12000506 MSFT 0x00000097) @
> 0x000000007ffc0040
> ACPI: DSDT (v001 939M2 939M2150 0x00000150 INTL 0x02002026) @
> 0x0000000000000000
> On node 0 totalpages: 1025626
> DMA zone: 2674 pages, LIFO batch:0
> DMA32 zone: 505832 pages, LIFO batch:31
> Normal zone: 517120 pages, LIFO batch:31
> HighMem zone: 0 pages, LIFO batch:0
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 15:3 APIC version 16
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> Processor #1 15:3 APIC version 16
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
> ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24])
> IOAPIC[1]: apic_id 3, version 17, address 0xfec10000, GSI 24-39
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Setting APIC routing to flat
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 88000000 (gap: 80000000:7f7c0000)
> Checking aperture...
> CPU 0: aperture @ d0000000 size 256 MB
> Built 1 zonelists
> Kernel command line: root=/dev/sda5 elevator=cfq quiet
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 131072 bytes)
> time.c: Using 3.579545 MHz PM timer.
> time.c: Detected 2000.122 MHz processor.
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
> Memory: 4095664k/6291456k available (3159k kernel code, 97584k reserved,
> 1267k data, 212k init)
> Calibrating delay using timer specific routine.. 4003.11 BogoMIPS
> (lpj=2001559)
> Mount-cache hash table entries: 256
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 512K (64 bytes/line)
> mtrr: v2.0 (20020519)
> Using local APIC timer interrupts.
> Detected 12.500 MHz APIC timer.
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3999.60 BogoMIPS
> (lpj=1999803)
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 512K (64 bytes/line)
> AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
> CPU 1: Syncing TSC to CPU 0.
> CPU 1: synchronized TSC with CPU 0 (last diff 3 cycles, maxerr 534 cycles)
> Brought up 2 CPUs
> Disabling vsyscall due to use of PM timer
> time.c: Using PM based timekeeping.
> testing NMI watchdog ... OK.
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: Using configuration type 1
> ACPI: Subsystem revision 20050902
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> PCI quirk: region 0800-083f claimed by ali7101 ACPI
> Boot video device is 0000:03:00.0
> PCI: Transparent bridge - 0000:00:06.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HTT_._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEB1._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEB2._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
> ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 13 devices
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
> report agpgart: Detected AGP bridge 20
> Setting up ULi AGP.
> agpgart: AGP aperture is 256M @ 0xd0000000
> PCI-DMA: Reserving 128MB of IOMMU area in the AGP aperture
> pnp: 00:0b: ioport range 0x290-0x29f has been reserved
> PCI: Bridge: 0000:00:01.0
> IO window: disabled.
> MEM window: fc700000-fc7fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:02.0
> IO window: disabled.
> MEM window: fc800000-fc8fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:05.0
> IO window: disabled.
> MEM window: fc900000-fe9fffff
> PREFETCH window: aff00000-bfefffff
> PCI: Bridge: 0000:00:06.0
> IO window: disabled.
> MEM window: fea00000-feafffff
> PREFETCH window: disabled.
> GSI 16 sharing vector 0xA9 and IRQ 16
> ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 29 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> GSI 17 sharing vector 0xB1 and IRQ 17
> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 34 (level, low) -> IRQ 177
> PCI: Setting latency timer of device 0000:00:02.0 to 64
> PCI: Setting latency timer of device 0000:00:05.0 to 64
> PCI: Setting latency timer of device 0000:00:06.0 to 64
> IA-32 Microcode Update Driver: v1.14 <[email protected]>
> IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
> Installing knfsd (copyright (C) 1996 [email protected]).
> NTFS driver 2.1.25 [Flags: R/W].
> fuse init (API version 7.3)
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 29 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[pcie00]
> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 34 (level, low) -> IRQ 177
> PCI: Setting latency timer of device 0000:00:02.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[pcie00]
> ACPI: Power Button (FF) [PWRF]
> ACPI: Power Button (CM) [PWRB]
> Using specific hotkey driver
> lp: driver loaded but no devices found
> Real Time Clock Driver v1.12
> Non-volatile memory driver v1.2
> Linux agpgart interface v0.101 (c) Dave Jones
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> parport: PnPBIOS parport detected.
> parport0: PC-style at 0x378 (0x778), irq 7, dma 3
> [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
> lp0: using parport0 (interrupt-driven).
> lp0: console ready
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> ALI15X3: IDE controller at PCI slot 0000:00:12.0
> GSI 18 sharing vector 0xD1 and IRQ 18
> ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 19 (level, low) -> IRQ 209
> ALI15X3: chipset revision 199
> ALI15X3: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:pio, hdd:pio
> Probing IDE interface ide0...
> hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> ide-floppy driver 0.99.newide
> libata version 1.20 loaded.
> sata_uli 0000:00:12.1: version 0.5
> ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 19 (level, low) -> IRQ 209
> ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE082 bmdma 0xD880 irq 209
> ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xDC02 bmdma 0xD888 irq 209
> ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663
> 88:007f
> ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
> ata1: dev 0 configured for UDMA/133
> scsi0 : sata_uli
> ata2: no device found (phy stat 00000000)
> scsi1 : sata_uli
> Vendor: ATA Model: Maxtor 7L250S0 Rev: BANC
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 < sda5 sda6 sda7 >
> sd 0:0:0:0: Attached scsi disk sda
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> usbmon: debugfs is not available
> GSI 19 sharing vector 0xD9 and IRQ 19
> ACPI: PCI Interrupt 0000:00:13.3[D] -> GSI 23 (level, low) -> IRQ 217
> ehci_hcd 0000:00:13.3: EHCI Host Controller
> ehci_hcd 0000:00:13.3: debug port 1
> ehci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:13.3: irq 217, io mem 0xfebfe800
> ehci_hcd 0000:00:13.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 8 ports detected
> ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> GSI 20 sharing vector 0xE1 and IRQ 20
> ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 20 (level, low) -> IRQ 225
> ohci_hcd 0000:00:13.0: OHCI Host Controller
> ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:00:13.0: irq 225, io mem 0xfebfd000
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 3 ports detected
> GSI 21 sharing vector 0xE9 and IRQ 21
> ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 21 (level, low) -> IRQ 233
> ohci_hcd 0000:00:13.1: OHCI Host Controller
> ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
> ohci_hcd 0000:00:13.1: irq 233, io mem 0xfebfc000
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 3 ports detected
> GSI 22 sharing vector 0x32 and IRQ 22
> ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 22 (level, low) -> IRQ 50
> ohci_hcd 0000:00:13.2: OHCI Host Controller
> ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
> ohci_hcd 0000:00:13.2: irq 50, io mem 0xfebfb000
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 3 ports detected
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> mice: PS/2 mouse device common for all mice
> I2O subsystem v1.288
> i2o: max drivers = 8
> I2O Configuration OSM v1.248
> I2O Bus Adapter OSM v$Rev$
> I2O Block Device OSM v1.287
> I2O SCSI Peripheral OSM v1.282
> I2O ProcFS OSM v1.145
> i2c /dev entries driver
> ali1563: SMBus control = 0403
> ali1563_probe: Returning 0
> input: AT Translated Set 2 keyboard as /class/input/input0
> Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07
> 13:30:21 2005 UTC).
> GSI 23 sharing vector 0x3A and IRQ 23
> ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 58
> input: ImPS/2 Generic Wheel Mouse as /class/input/input1
> AC'97 1 does not respond - RESET
> AC'97 1 access is not valid [0xffffffff], removing mixer.
> Unable to initialize codec #1
> intel8x0_measure_ac97_clock: measured 50953 usecs
> intel8x0: clocking to 48000
> ALSA device list:
> #0: ALi M5455 with ALC850 at 0x0, irq 58
> NET: Registered protocol family 2
> IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
> TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
> TCP: Hash tables configured (established 262144 bind 65536)
> TCP reno registered
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4)
> powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
> powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
> powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0xa (1300 mV)
> cpu_init done, current fid 0xc, vid 0x8
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 212k freed
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on sda5, internal journal
> uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
> GSI 24 sharing vector 0x42 and IRQ 24
> ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 17 (level, low) -> IRQ 66
> eth0: ULi M5263 at pci0000:00:11.0, 00:13:8f:5d:2e:ea, irq 66.
> ReiserFS: sda6: found reiserfs format "3.6" with standard journal
> ReiserFS: sda6: using ordered data mode
> ReiserFS: sda6: journal params: device sda6, size 8192, journal first block
> 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
> ReiserFS: sda6: checking transaction log (sda6)
> ReiserFS: sda6: Using r5 hash to sort names
> uli526x: eth0 NIC Link is Up 100 Mbps Full duplex
> NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
> NFSD: starting 90-second grace period
> mtrr: type mismatch for b0000000,2000000 old: write-back new:
> write-combining
>
>
> 00:00.0 Host bridge: ALi Corporation M1695 K8 Northbridge [PCI Express and
> HyperTransport]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Capabilities: [40] HyperTransport: Slave or Primary Interface
> Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir- DUL-
> Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut-
> LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
> Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut-
> LWI=8bit DwFcInEn- LWO=16bit DwFcOutEn-
> Revision ID: 1.05
> Link Frequency 0: 800MHz
> Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+
> 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
> Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA-
> UIDRD-
> Link Frequency 1: 200MHz
> Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 1: 200MHz+ 300MHz- 400MHz+
> 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
> Error Handling: PFlE+ OFlE+ PFE+ OFE+ EOCFE+ RFE+ CRCFE+
> SERRFE- CF- RE- PNFE+ ONFE+ EOCNFE+ RNFE- CRCNFE+ SERRNFE-
> Prefetchable memory behind bridge Upper: 00-00
> Bus Number: 00
> Capabilities: [5c] HyperTransport: MSI Mapping
> Capabilities: [68] HyperTransport: UnitID Clumping
> Capabilities: [74] HyperTransport: Interrupt Discovery and
> Configuration
> Capabilities: [7c] Message Signalled Interrupts: 64bit+ Queue=0/1
> Enable-
> Address: 00000000fee00000 Data: 0000
> 00: b9 10 95 16 07 00 10 00 00 00 00 06 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
> 40: 08 5c 60 00 20 00 11 11 20 00 11 10 25 05 f5 00
> 50: 02 00 f5 00 ff ff 7f 5c 00 00 00 00 08 68 00 a8
> 60: 00 00 e0 fe 00 00 00 00 08 74 00 90 00 00 00 00
> 70: 00 00 00 00 08 7c 00 80 67 03 b1 f8 05 00 82 00
> 80: 00 00 e0 fe 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:01.0 PCI bridge: ALi Corporation PCI Express Root Port (prog-if 00
> [Normal decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size 10
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fc700000-fc7fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1
> Enable+
> Address: 00000000fee00000 Data: 40c1
> Capabilities: [58] Express Root Port (Slot+) IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
> ExtTag+ Device: Latency L0s <64ns, L1 <1us
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
> Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port
> 0 Link: Latency L0s <2us, L1 <32us
> Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
> Link: Speed 2.5Gb/s, Width x16
> Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug-
> Surpise- Slot: Number 0, PowerLimit 0.000000
> Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
> Slot: AttnInd Off, PwrInd Off, Power-
> Root: Correctable- Non-Fatal- Fatal- PME-
> Capabilities: [7c] HyperTransport: MSI Mapping
> Capabilities: [88] HyperTransport: Revision ID: 1.05
> 00: b9 10 4b 52 06 05 10 00 00 00 04 06 10 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00
> 20: 70 fc 70 fc f0 ff 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 03 00
> 40: 01 48 02 c8 00 00 00 00 05 58 83 00 00 00 e0 fe
> 50: 00 00 00 00 c1 40 00 00 10 7c 41 01 20 00 00 00
> 60: 10 28 18 00 01 dd 02 00 00 00 10 10 00 00 00 00
> 70: c0 03 00 00 00 00 00 00 00 00 00 00 08 88 00 a8
> 80: 00 00 e0 fe 00 00 00 00 08 00 25 88 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 03 00 00 00 00 00 0c 02 08 3f 63 ed 70 2c
> b0: 00 00 00 00 00 11 00 00 00 00 00 00 01 00 3f 1f
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 01 d0 0c 40 01 04 73 00 00 00 00 00 d1 00 77 30
> e0: 00 00 00 00 01 00 00 00 01 00 00 00 26 38 18 d0
> f0: 01 50 94 2d 59 41 50 86 06 38 ef 53 40 0e 66 c1
>
> 00:02.0 PCI bridge: ALi Corporation PCI Express Root Port (prog-if 00
> [Normal decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size 10
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fc800000-fc8fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1
> Enable+
> Address: 00000000fee00000 Data: 40c9
> Capabilities: [58] Express Root Port (Slot+) IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
> ExtTag+ Device: Latency L0s <64ns, L1 <1us
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
> Link: Supported Speed 2.5Gb/s, Width x2, ASPM L0s L1, Port
> 0 Link: Latency L0s <2us, L1 <32us
> Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
> Link: Speed 2.5Gb/s, Width x2
> Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug-
> Surpise- Slot: Number 0, PowerLimit 0.000000
> Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
> Slot: AttnInd Off, PwrInd Off, Power-
> Root: Correctable- Non-Fatal- Fatal- PME-
> Capabilities: [7c] HyperTransport: MSI Mapping
> Capabilities: [88] HyperTransport: Revision ID: 1.05
> 00: b9 10 4c 52 06 05 10 00 00 00 04 06 10 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 02 02 00 f0 00 00 00
> 20: 80 fc 80 fc f0 ff 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 03 00
> 40: 01 48 02 c8 00 00 00 00 05 58 83 00 00 00 e0 fe
> 50: 00 00 00 00 c9 40 00 00 10 7c 41 01 20 00 00 00
> 60: 10 28 18 00 21 dc 02 00 00 00 10 10 00 00 00 00
> 70: c0 03 00 00 00 00 00 00 00 00 00 00 08 88 00 a8
> 80: 00 00 e0 fe 00 00 00 00 08 00 25 88 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 03 00 00 00 00 00 0c 02 09 3f 63 ed 70 2c
> b0: 00 00 00 00 00 11 00 00 04 00 00 00 01 00 3f 1f
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 01 d0 0c 40 01 04 73 00 00 00 00 00 d1 00 77 30
> e0: 00 00 00 00 01 00 00 00 01 00 00 00 64 b1 41 40
> f0: d7 2e 91 66 7e 1d fc 1a cc 24 dc 44 22 2d 40 a4
>
> 00:04.0 Host bridge: ALi Corporation M1689 K8 Northbridge [Super K8 Single
> Chip]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
> Capabilities: [40] HyperTransport: Slave or Primary Interface
> Command: BaseUnitID=4 UnitCnt=1 MastHost- DefDir- DUL-
> Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 0: MLWI=16bit DwFcIn- MLWO=8bit DwFcOut-
> LWI=16bit DwFcInEn- LWO=8bit DwFcOutEn-
> Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut-
> LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
> Revision ID: 1.04
> Link Frequency 0: 800MHz
> Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+
> 500MHz- 600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
> Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA-
> UIDRD-
> Link Frequency 1: 200MHz
> Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 1: 200MHz- 300MHz- 400MHz-
> 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
> Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE-
> SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
> Prefetchable memory behind bridge Upper: 00-00
> Bus Number: 00
> Capabilities: [60] HyperTransport: Interrupt Discovery and
> Configuration
> Capabilities: [80] AGP version 3.0
> Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
> HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
> Rate=<none>
> 00: b9 10 89 16 06 01 10 00 00 00 00 06 00 00 00 00
> 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
> 40: 08 60 24 00 20 00 01 01 d0 00 00 00 24 05 35 00
> 50: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 08 80 32 80 66 03 42 f8 00 00 00 00 00 05 17 50
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 02 00 30 00 07 02 00 1b 00 00 00 00 0a 00 20 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:05.0 PCI bridge: ALi Corporation AGP8X Controller (prog-if 00 [Normal
> decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fc900000-fe9fffff
> Prefetchable memory behind bridge: aff00000-bfefffff
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
> 00: b9 10 46 52 07 01 20 00 00 00 04 06 00 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 03 03 40 f0 00 20 22
> 20: 90 fc 90 fe f0 af e0 bf 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0b 00
> 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 20 78 00 c0 00 20 20 20 20 20 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 11 00 00 00 00 11 00 01 20 1a
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:06.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge (prog-if 01
> [Subtractive decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fea00000-feafffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> 00: b9 10 49 52 06 01 00 00 00 01 04 06 00 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 04 04 20 f0 00 00 22
> 20: a0 fe a0 fe f0 ff 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03 00
> 40: 00 80 00 78 00 00 00 00 80 00 00 20 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:07.0 ISA bridge: ALi Corporation M1563 HyperTransport South Bridge (rev
> 70) Subsystem: ASRock Incorporation Unknown device 1563
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (250ns min, 6000ns max)
> 00: b9 10 63 15 0f 00 00 02 70 00 01 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 63 15
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 18
> 40: f7 e4 00 09 3d fa 00 00 00 00 00 00 03 c0 00 10
> 50: 02 00 02 00 0d 09 01 80 ff 3c fb 67 a1 60 10 00
> 60: d8 f8 c0 f2 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 07 63 15 00 0f 00 00 00 00 00 20 00 00 00 00
> 80: 03 04 00 00 21 0f cc dd ee 99 aa 99 00 bb 00 5f
> 90: 80 03 83 00 00 00 00 00 1e 00 00 00 00 00 e0 fe
> a0: 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: df 80 01 00 c0 00 f0 08 5f 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:07.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
> Subsystem: ASRock Incorporation Unknown device 7101
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> 00: b9 10 01 71 00 00 00 02 00 00 80 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 01 71
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 40 00 00 00 00 20 00 08 7a 00 00 00 00 00 00
> 50: 00 07 ff 58 00 00 00 00 00 df 0f 10 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 ff 3f 3f 3f
> 70: ff 07 00 00 00 00 00 08 76 88 b0 08 3c fe ff 00
> 80: 32 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 a0 aa 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: ff 44 80 20 00 ff ff 07 00 00 28 70 40 9b 02 00
> c0: 12 00 10 10 00 00 00 00 00 00 ff 00 4b 00 00 00
> d0: 00 42 04 00 40 00 22 04 4c 2f 00 00 00 00 00 00
> e0: 00 08 00 00 0e 29 cb 55 b4 00 01 00 00 00 00 36
> f0: 00 00 00 00 00 00 00 f0 00 00 00 00 00 00 00 00
>
> 00:08.0 Multimedia audio controller: ALi Corporation M5455 PCI AC-Link
> Controller Audio Device (rev 20)
> Subsystem: ASRock Incorporation Unknown device 0850
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (16000ns min), Cache Line Size 10
> Interrupt: pin A routed to IRQ 58
> Region 0: I/O ports at e800 [size=256]
> Region 1: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: b9 10 55 54 17 00 10 02 20 00 01 04 10 20 00 00
> 10: 01 e8 00 00 00 f0 bf fe 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 50 08
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 03 01 40 00
> 40: 01 00 22 e6 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 49 18 50 08 10 00 c4 00 40 00 07 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 57 54 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:11.0 Ethernet controller: ALi Corporation M5263 Ethernet Controller (rev
> 40)
> Subsystem: ASRock Incorporation Unknown device 5263
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (5000ns min, 10000ns max), Cache Line Size 08
> Interrupt: pin A routed to IRQ 66
> Region 0: I/O ports at e400 [size=256]
> Region 1: Memory at febfec00 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: b9 10 63 52 07 01 10 02 40 00 00 02 08 20 00 00
> 10: 01 e4 00 00 00 ec bf fe 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 63 52
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 14 28
> 40: 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 01 00 22 c0 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:12.0 IDE interface: ALi Corporation M5229 IDE (rev c7) (prog-if 8a
> [Master SecP PriP])
> Subsystem: ASRock Incorporation Unknown device 5229
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin A routed to IRQ 209
> Region 0: I/O ports at <ignored>
> Region 1: I/O ports at <ignored>
> Region 2: I/O ports at <ignored>
> Region 3: I/O ports at <ignored>
> Region 4: I/O ports at ff00 [size=16]
> 00: b9 10 29 52 05 00 a0 02 c7 8a 01 01 00 20 80 00
> 10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00
> 20: 01 ff 00 00 00 00 00 00 00 00 00 00 49 18 29 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
> 40: 00 00 00 7a 4d 10 00 c0 00 80 64 c9 00 00 ba 1a
> 50: 00 00 00 01 50 55 4a 44 01 31 31 00 00 00 00 00
> 60: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 01 00 01 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:12.1 IDE interface: ALi Corporation ULi 5289 SATA (rev 10) (prog-if 8f
> [Master SecP SecO PriP PriO])
> Subsystem: ASRock Incorporation Unknown device 5289
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, Cache Line Size 10
> Interrupt: pin A routed to IRQ 209
> Region 0: I/O ports at ec00 [size=8]
> Region 1: I/O ports at e080 [size=4]
> Region 2: I/O ports at e000 [size=8]
> Region 3: I/O ports at dc00 [size=4]
> Region 4: I/O ports at d880 [size=16]
> 00: b9 10 89 52 05 01 a0 02 10 8f 01 01 10 20 80 00
> 10: 01 ec 00 00 81 e0 00 00 01 e0 00 00 01 dc 00 00
> 20: 81 d8 00 00 00 00 00 00 00 00 00 00 49 18 89 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 06 01 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 1f 00 00 03 10 01 00 00 00 68 00 68 00
> 90: 13 01 00 00 01 04 8d 04 00 03 00 00 00 00 00 00
> a0: 00 00 00 00 00 04 80 00 00 03 00 00 00 00 00 00
> b0: 00 00 00 00 88 b1 0e 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:13.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> (prog-if 10 [OHCI])
> Subsystem: ASRock Incorporation Unknown device 5237
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), Cache Line Size 10
> Interrupt: pin A routed to IRQ 225
> Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
> 00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
> 10: 00 d0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 50
> 40: 00 00 1f 00 e0 40 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:13.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> (prog-if 10 [OHCI])
> Subsystem: ASRock Incorporation Unknown device 5237
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), Cache Line Size 10
> Interrupt: pin B routed to IRQ 233
> Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
> 00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
> 10: 00 c0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 50
> 40: 00 00 1f 00 e0 48 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:13.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> (prog-if 10 [OHCI])
> Subsystem: ASRock Incorporation Unknown device 5237
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), Cache Line Size 10
> Interrupt: pin C routed to IRQ 50
> Region 0: Memory at febfb000 (32-bit, non-prefetchable) [size=4K]
> 00: b9 10 37 52 17 01 a8 02 03 10 03 0c 10 20 80 00
> 10: 00 b0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 37 52
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 50
> 40: 00 00 1f 00 e0 48 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:13.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
> (prog-if 20 [EHCI])
> Subsystem: ASRock Incorporation Unknown device 5239
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (4000ns min, 8000ns max), Cache Line Size 10
> Interrupt: pin D routed to IRQ 217
> Region 0: Memory at febfe800 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Debug port
> 00: b9 10 39 52 16 01 b0 02 01 20 03 0c 10 20 80 00
> 10: 00 e8 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 39 52
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 10 20
> 40: 20 03 00 c4 80 02 10 c4 00 00 00 00 00 00 00 00
> 50: 01 58 02 c8 00 00 00 00 0a 00 90 20 00 00 00 00
> 60: 20 20 7f 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 01 00 00 01 00 00 08 c0 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> HyperTransport Technology Configuration
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Capabilities: [80] HyperTransport: Host or Secondary Interface
> !!! Possibly incomplete decoding
> Command: WarmRst+ DblEnd-
> Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
> <CRCErr=0
> Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
> Revision ID: 1.02
> 00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
> 40: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
> 50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
> 60: 00 00 01 00 e4 00 00 00 20 c8 00 0f 1c 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 08 00 01 21 20 00 11 11 22 05 75 80 02 00 00 00
> 90: 56 04 51 02 00 00 ff 00 07 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Address Map
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 03 00 00 00 00 00 7f 01 00 00 00 00 01 00 00 00
> 50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00
> 60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00
> 70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00
> 80: 03 00 e0 00 00 ff ef 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 03 0a 00 00 00 0b 00 00 03 00 80 00 00 ff ff 00
> c0: 13 10 00 00 00 f0 ff 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 03 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> DRAM Controller
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 01 00 00 00 01 00 00 04 01 00 00 10 01 00 00 14
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 fe e0 03 00 fe e0 03 00 fe e0 03 00 fe e0 03
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 77 00 00 00 00 00 00 00 45 34 82 13 31 0b 00 00
> 90: 80 8e 05 38 07 07 7b 3e 00 00 00 00 0d 02 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 71 9f 5e 3b 71 00 00 00 ff 31 00 00 bd ae fb ff
> c0: 00 80 03 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 15 4c f1 f0 24 80 c8 20 4d eb fe f4 10 90 00 1a
> e0: 45 1c 34 00 11 18 40 40 d3 55 bf b7 1f 6d 3c fd
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Miscellaneous Control
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 03 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: ff 3b 00 00 40 00 00 08 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 80 90 45 01
> 60: 8c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 11 01 02 51 11 80 00 50 00 38 00 08 1a 22 00 00
> 80: 00 00 07 23 13 21 13 21 00 00 00 00 00 00 00 00
> 90: 07 00 00 00 68 00 00 00 00 80 7f 01 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 37 00 00 00 00 80 4d 5c
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 01 a7 0d 00 10 27 60 20 00 00 00 00
> e0: 00 00 00 00 20 07 4e 0e 19 11 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 03:00.0 VGA compatible controller: nVidia Corporation NV15 [GeForce2
> GTS/Pro] (rev a3) (prog-if 00 [VGA])
> Subsystem: Elsa AG Gladiac
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at b0000000 (32-bit, prefetchable) [size=128M]
> Expansion ROM at fe9f0000 [disabled] [size=64K]
> Capabilities: [60] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 2.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
> HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
> Rate=<none>
> 00: de 10 50 01 07 00 b0 02 a3 00 00 03 00 20 00 00
> 10: 00 00 00 fd 08 00 00 b0 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 48 10 50 0c
> 30: 00 00 9f fe 60 00 00 00 00 00 00 00 05 01 05 01
> 40: 48 10 50 0c 02 00 20 00 17 00 00 1f 00 00 00 00
> 50: 01 00 00 00 01 00 00 00 ce d6 23 00 0f 00 00 00
> 60: 01 44 01 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> #
> # Automatically generated make config: don't edit
> # Linux kernel version: 2.6.15
> # Thu Jan 12 14:47:37 2006
> #
> CONFIG_X86_64=y
> CONFIG_64BIT=y
> CONFIG_X86=y
> CONFIG_SEMAPHORE_SLEEPERS=y
> CONFIG_MMU=y
> CONFIG_RWSEM_GENERIC_SPINLOCK=y
> CONFIG_GENERIC_CALIBRATE_DELAY=y
> CONFIG_X86_CMPXCHG=y
> CONFIG_EARLY_PRINTK=y
> CONFIG_GENERIC_ISA_DMA=y
> CONFIG_GENERIC_IOMAP=y
> CONFIG_ARCH_MAY_HAVE_PC_FDC=y
>
> #
> # Code maturity level options
> #
> CONFIG_EXPERIMENTAL=y
> # CONFIG_CLEAN_COMPILE is not set
> CONFIG_BROKEN=y
> CONFIG_BROKEN_ON_SMP=y
> CONFIG_LOCK_KERNEL=y
> CONFIG_INIT_ENV_ARG_LIMIT=32
>
> #
> # General setup
> #
> CONFIG_LOCALVERSION=""
> CONFIG_LOCALVERSION_AUTO=y
> CONFIG_SWAP=y
> CONFIG_SYSVIPC=y
> CONFIG_POSIX_MQUEUE=y
> # CONFIG_BSD_PROCESS_ACCT is not set
> CONFIG_SYSCTL=y
> # CONFIG_AUDIT is not set
> CONFIG_HOTPLUG=y
> CONFIG_KOBJECT_UEVENT=y
> CONFIG_IKCONFIG=y
> CONFIG_IKCONFIG_PROC=y
> # CONFIG_CPUSETS is not set
> CONFIG_INITRAMFS_SOURCE=""
> CONFIG_CC_OPTIMIZE_FOR_SIZE=y
> # CONFIG_EMBEDDED is not set
> CONFIG_KALLSYMS=y
> # CONFIG_KALLSYMS_ALL is not set
> # CONFIG_KALLSYMS_EXTRA_PASS is not set
> CONFIG_PRINTK=y
> CONFIG_BUG=y
> CONFIG_BASE_FULL=y
> CONFIG_FUTEX=y
> CONFIG_EPOLL=y
> CONFIG_SHMEM=y
> CONFIG_CC_ALIGN_FUNCTIONS=0
> CONFIG_CC_ALIGN_LABELS=0
> CONFIG_CC_ALIGN_LOOPS=0
> CONFIG_CC_ALIGN_JUMPS=0
> # CONFIG_TINY_SHMEM is not set
> CONFIG_BASE_SMALL=0
>
> #
> # Loadable module support
> #
> CONFIG_MODULES=y
> CONFIG_MODULE_UNLOAD=y
> # CONFIG_MODULE_FORCE_UNLOAD is not set
> CONFIG_OBSOLETE_MODPARM=y
> # CONFIG_MODVERSIONS is not set
> # CONFIG_MODULE_SRCVERSION_ALL is not set
> CONFIG_KMOD=y
> CONFIG_STOP_MACHINE=y
>
> #
> # Block layer
> #
> CONFIG_LBD=y
>
> #
> # IO Schedulers
> #
> CONFIG_IOSCHED_NOOP=y
> CONFIG_IOSCHED_AS=y
> CONFIG_IOSCHED_DEADLINE=y
> CONFIG_IOSCHED_CFQ=y
> # CONFIG_DEFAULT_AS is not set
> # CONFIG_DEFAULT_DEADLINE is not set
> CONFIG_DEFAULT_CFQ=y
> # CONFIG_DEFAULT_NOOP is not set
> CONFIG_DEFAULT_IOSCHED="cfq"
>
> #
> # Processor type and features
> #
> CONFIG_MK8=y
> # CONFIG_MPSC is not set
> # CONFIG_GENERIC_CPU is not set
> CONFIG_X86_L1_CACHE_BYTES=64
> CONFIG_X86_L1_CACHE_SHIFT=6
> CONFIG_X86_TSC=y
> CONFIG_X86_GOOD_APIC=y
> CONFIG_MICROCODE=y
> CONFIG_X86_MSR=y
> CONFIG_X86_CPUID=y
> CONFIG_X86_IO_APIC=y
> CONFIG_X86_LOCAL_APIC=y
> CONFIG_MTRR=y
> CONFIG_SMP=y
> # CONFIG_SCHED_SMT is not set
> # CONFIG_PREEMPT_NONE is not set
> # CONFIG_PREEMPT_VOLUNTARY is not set
> CONFIG_PREEMPT=y
> CONFIG_PREEMPT_BKL=y
> # CONFIG_NUMA is not set
> CONFIG_ARCH_FLATMEM_ENABLE=y
> CONFIG_SELECT_MEMORY_MODEL=y
> CONFIG_FLATMEM_MANUAL=y
> # CONFIG_DISCONTIGMEM_MANUAL is not set
> # CONFIG_SPARSEMEM_MANUAL is not set
> CONFIG_FLATMEM=y
> CONFIG_FLAT_NODE_MEM_MAP=y
> # CONFIG_SPARSEMEM_STATIC is not set
> CONFIG_SPLIT_PTLOCK_CPUS=4
> CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID=y
> CONFIG_NR_CPUS=2
> # CONFIG_HOTPLUG_CPU is not set
> CONFIG_HPET_TIMER=y
> CONFIG_X86_PM_TIMER=y
> CONFIG_HPET_EMULATE_RTC=y
> CONFIG_GART_IOMMU=y
> CONFIG_SWIOTLB=y
> CONFIG_X86_MCE=y
> CONFIG_X86_MCE_INTEL=y
> CONFIG_X86_MCE_AMD=y
> CONFIG_PHYSICAL_START=0x100000
> CONFIG_KEXEC=y
> CONFIG_SECCOMP=y
> # CONFIG_HZ_100 is not set
> # CONFIG_HZ_250 is not set
> CONFIG_HZ_1000=y
> CONFIG_HZ=1000
> CONFIG_GENERIC_HARDIRQS=y
> CONFIG_GENERIC_IRQ_PROBE=y
> CONFIG_ISA_DMA_API=y
> CONFIG_GENERIC_PENDING_IRQ=y
>
> #
> # Power management options
> #
> CONFIG_PM=y
> CONFIG_PM_LEGACY=y
> # CONFIG_PM_DEBUG is not set
>
> #
> # ACPI (Advanced Configuration and Power Interface) Support
> #
> CONFIG_ACPI=y
> CONFIG_ACPI_AC=y
> CONFIG_ACPI_BATTERY=y
> CONFIG_ACPI_BUTTON=y
> CONFIG_ACPI_VIDEO=y
> CONFIG_ACPI_HOTKEY=y
> CONFIG_ACPI_FAN=y
> CONFIG_ACPI_PROCESSOR=y
> CONFIG_ACPI_THERMAL=y
> # CONFIG_ACPI_ASUS is not set
> # CONFIG_ACPI_IBM is not set
> # CONFIG_ACPI_TOSHIBA is not set
> # CONFIG_ACPI_CUSTOM_DSDT is not set
> CONFIG_ACPI_BLACKLIST_YEAR=0
> # CONFIG_ACPI_DEBUG is not set
> CONFIG_ACPI_EC=y
> CONFIG_ACPI_POWER=y
> CONFIG_ACPI_SYSTEM=y
> CONFIG_ACPI_CONTAINER=y
>
> #
> # CPU Frequency scaling
> #
> CONFIG_CPU_FREQ=y
> CONFIG_CPU_FREQ_TABLE=y
> # CONFIG_CPU_FREQ_DEBUG is not set
> CONFIG_CPU_FREQ_STAT=y
> # CONFIG_CPU_FREQ_STAT_DETAILS is not set
> CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
> # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
> CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
> CONFIG_CPU_FREQ_GOV_POWERSAVE=y
> CONFIG_CPU_FREQ_GOV_USERSPACE=y
> CONFIG_CPU_FREQ_GOV_ONDEMAND=y
> CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
>
> #
> # CPUFreq processor drivers
> #
> CONFIG_X86_POWERNOW_K8=y
> CONFIG_X86_POWERNOW_K8_ACPI=y
> # CONFIG_X86_SPEEDSTEP_CENTRINO is not set
> CONFIG_X86_ACPI_CPUFREQ=y
>
> #
> # shared options
> #
> # CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
> # CONFIG_X86_SPEEDSTEP_LIB is not set
>
> #
> # Bus options (PCI etc.)
> #
> CONFIG_PCI=y
> CONFIG_PCI_DIRECT=y
> CONFIG_PCI_MMCONFIG=y
> CONFIG_UNORDERED_IO=y
> CONFIG_PCIEPORTBUS=y
> CONFIG_PCI_MSI=y
> CONFIG_PCI_LEGACY_PROC=y
> # CONFIG_PCI_DEBUG is not set
>
> #
> # PCCARD (PCMCIA/CardBus) support
> #
> # CONFIG_PCCARD is not set
>
> #
> # PCI Hotplug Support
> #
> # CONFIG_HOTPLUG_PCI is not set
>
> #
> # Executable file formats / Emulations
> #
> CONFIG_BINFMT_ELF=y
> CONFIG_BINFMT_MISC=y
> CONFIG_IA32_EMULATION=y
> # CONFIG_IA32_AOUT is not set
> CONFIG_COMPAT=y
> CONFIG_SYSVIPC_COMPAT=y
> CONFIG_UID16=y
>
> #
> # Networking
> #
> CONFIG_NET=y
>
> #
> # Networking options
> #
> CONFIG_PACKET=y
> # CONFIG_PACKET_MMAP is not set
> CONFIG_UNIX=y
> # CONFIG_NET_KEY is not set
> CONFIG_INET=y
> CONFIG_IP_MULTICAST=y
> # CONFIG_IP_ADVANCED_ROUTER is not set
> CONFIG_IP_FIB_HASH=y
> # CONFIG_IP_PNP is not set
> # CONFIG_NET_IPIP is not set
> # CONFIG_NET_IPGRE is not set
> # CONFIG_IP_MROUTE is not set
> # CONFIG_ARPD is not set
> # CONFIG_SYN_COOKIES is not set
> # CONFIG_INET_AH is not set
> # CONFIG_INET_ESP is not set
> # CONFIG_INET_IPCOMP is not set
> # CONFIG_INET_TUNNEL is not set
> CONFIG_INET_DIAG=y
> CONFIG_INET_TCP_DIAG=y
> # CONFIG_TCP_CONG_ADVANCED is not set
> CONFIG_TCP_CONG_BIC=y
> # CONFIG_IPV6 is not set
> # CONFIG_NETFILTER is not set
>
> #
> # DCCP Configuration (EXPERIMENTAL)
> #
> # CONFIG_IP_DCCP is not set
>
> #
> # SCTP Configuration (EXPERIMENTAL)
> #
> # CONFIG_IP_SCTP is not set
> # CONFIG_ATM is not set
> # CONFIG_BRIDGE is not set
> # CONFIG_VLAN_8021Q is not set
> # CONFIG_DECNET is not set
> # CONFIG_LLC2 is not set
> # CONFIG_IPX is not set
> # CONFIG_ATALK is not set
> # CONFIG_X25 is not set
> # CONFIG_LAPB is not set
> # CONFIG_NET_DIVERT is not set
> # CONFIG_ECONET is not set
> # CONFIG_WAN_ROUTER is not set
>
> #
> # QoS and/or fair queueing
> #
> # CONFIG_NET_SCHED is not set
>
> #
> # Network testing
> #
> # CONFIG_NET_PKTGEN is not set
> # CONFIG_HAMRADIO is not set
> # CONFIG_IRDA is not set
> # CONFIG_BT is not set
> # CONFIG_IEEE80211 is not set
>
> #
> # Device Drivers
> #
>
> #
> # Generic Driver Options
> #
> # CONFIG_STANDALONE is not set
> CONFIG_PREVENT_FIRMWARE_BUILD=y
> # CONFIG_FW_LOADER is not set
> # CONFIG_DEBUG_DRIVER is not set
>
> #
> # Connector - unified userspace <-> kernelspace linker
> #
> # CONFIG_CONNECTOR is not set
>
> #
> # Memory Technology Devices (MTD)
> #
> # CONFIG_MTD is not set
>
> #
> # Parallel port support
> #
> CONFIG_PARPORT=y
> CONFIG_PARPORT_PC=y
> # CONFIG_PARPORT_SERIAL is not set
> CONFIG_PARPORT_PC_FIFO=y
> CONFIG_PARPORT_PC_SUPERIO=y
> # CONFIG_PARPORT_GSC is not set
> CONFIG_PARPORT_1284=y
>
> #
> # Plug and Play support
> #
> CONFIG_PNP=y
> # CONFIG_PNP_DEBUG is not set
>
> #
> # Protocols
> #
> CONFIG_PNPACPI=y
>
> #
> # Block devices
> #
> CONFIG_BLK_DEV_FD=m
> # CONFIG_PARIDE is not set
> # CONFIG_BLK_CPQ_DA is not set
> # CONFIG_BLK_CPQ_CISS_DA is not set
> # CONFIG_BLK_DEV_DAC960 is not set
> # CONFIG_BLK_DEV_UMEM is not set
> # CONFIG_BLK_DEV_COW_COMMON is not set
> # CONFIG_BLK_DEV_LOOP is not set
> # CONFIG_BLK_DEV_NBD is not set
> # CONFIG_BLK_DEV_SX8 is not set
> # CONFIG_BLK_DEV_UB is not set
> # CONFIG_BLK_DEV_RAM is not set
> CONFIG_BLK_DEV_RAM_COUNT=16
> # CONFIG_CDROM_PKTCDVD is not set
> # CONFIG_ATA_OVER_ETH is not set
>
> #
> # ATA/ATAPI/MFM/RLL support
> #
> CONFIG_IDE=y
> CONFIG_BLK_DEV_IDE=y
>
> #
> # Please see Documentation/ide.txt for help/info on IDE drives
> #
> # CONFIG_BLK_DEV_IDE_SATA is not set
> # CONFIG_BLK_DEV_HD_IDE is not set
> CONFIG_BLK_DEV_IDEDISK=y
> CONFIG_IDEDISK_MULTI_MODE=y
> CONFIG_BLK_DEV_IDECD=y
> # CONFIG_BLK_DEV_IDETAPE is not set
> CONFIG_BLK_DEV_IDEFLOPPY=y
> # CONFIG_BLK_DEV_IDESCSI is not set
> # CONFIG_IDE_TASK_IOCTL is not set
>
> #
> # IDE chipset support/bugfixes
> #
> # CONFIG_IDE_GENERIC is not set
> # CONFIG_BLK_DEV_CMD640 is not set
> # CONFIG_BLK_DEV_IDEPNP is not set
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> # CONFIG_BLK_DEV_GENERIC is not set
> # CONFIG_BLK_DEV_OPTI621 is not set
> # CONFIG_BLK_DEV_RZ1000 is not set
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> # CONFIG_BLK_DEV_IDEDMA_FORCED is not set
> CONFIG_IDEDMA_PCI_AUTO=y
> # CONFIG_IDEDMA_ONLYDISK is not set
> # CONFIG_BLK_DEV_AEC62XX is not set
> CONFIG_BLK_DEV_ALI15X3=y
> # CONFIG_WDC_ALI15X3 is not set
> # CONFIG_BLK_DEV_AMD74XX is not set
> # CONFIG_BLK_DEV_ATIIXP is not set
> # CONFIG_BLK_DEV_CMD64X is not set
> # CONFIG_BLK_DEV_TRIFLEX is not set
> # CONFIG_BLK_DEV_CY82C693 is not set
> # CONFIG_BLK_DEV_CS5520 is not set
> # CONFIG_BLK_DEV_CS5530 is not set
> # CONFIG_BLK_DEV_HPT34X is not set
> # CONFIG_BLK_DEV_HPT366 is not set
> # CONFIG_BLK_DEV_SC1200 is not set
> # CONFIG_BLK_DEV_PIIX is not set
> # CONFIG_BLK_DEV_IT821X is not set
> # CONFIG_BLK_DEV_NS87415 is not set
> # CONFIG_BLK_DEV_PDC202XX_OLD is not set
> # CONFIG_BLK_DEV_PDC202XX_NEW is not set
> # CONFIG_BLK_DEV_SVWKS is not set
> # CONFIG_BLK_DEV_SIIMAGE is not set
> # CONFIG_BLK_DEV_SIS5513 is not set
> # CONFIG_BLK_DEV_SLC90E66 is not set
> # CONFIG_BLK_DEV_TRM290 is not set
> # CONFIG_BLK_DEV_VIA82CXXX is not set
> # CONFIG_IDE_ARM is not set
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_IDEDMA_IVB is not set
> CONFIG_IDEDMA_AUTO=y
> # CONFIG_BLK_DEV_HD is not set
>
> #
> # SCSI device support
> #
> # CONFIG_RAID_ATTRS is not set
> CONFIG_SCSI=y
> CONFIG_SCSI_PROC_FS=y
>
> #
> # SCSI support type (disk, tape, CD-ROM)
> #
> CONFIG_BLK_DEV_SD=y
> # CONFIG_CHR_DEV_ST is not set
> # CONFIG_CHR_DEV_OSST is not set
> # CONFIG_BLK_DEV_SR is not set
> CONFIG_CHR_DEV_SG=y
> # CONFIG_CHR_DEV_SCH is not set
>
> #
> # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
> #
> # CONFIG_SCSI_MULTI_LUN is not set
> # CONFIG_SCSI_CONSTANTS is not set
> # CONFIG_SCSI_LOGGING is not set
>
> #
> # SCSI Transport Attributes
> #
> # CONFIG_SCSI_SPI_ATTRS is not set
> # CONFIG_SCSI_FC_ATTRS is not set
> # CONFIG_SCSI_ISCSI_ATTRS is not set
> # CONFIG_SCSI_SAS_ATTRS is not set
>
> #
> # SCSI low-level drivers
> #
> # CONFIG_ISCSI_TCP is not set
> # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
> # CONFIG_SCSI_3W_9XXX is not set
> # CONFIG_SCSI_ACARD is not set
> # CONFIG_SCSI_AACRAID is not set
> # CONFIG_SCSI_AIC7XXX is not set
> # CONFIG_SCSI_AIC7XXX_OLD is not set
> # CONFIG_SCSI_AIC79XX is not set
> # CONFIG_SCSI_ADVANSYS is not set
> # CONFIG_MEGARAID_NEWGEN is not set
> # CONFIG_MEGARAID_LEGACY is not set
> # CONFIG_MEGARAID_SAS is not set
> CONFIG_SCSI_SATA=y
> CONFIG_SCSI_SATA_AHCI=y
> # CONFIG_SCSI_SATA_SVW is not set
> # CONFIG_SCSI_ATA_PIIX is not set
> # CONFIG_SCSI_SATA_MV is not set
> # CONFIG_SCSI_SATA_NV is not set
> # CONFIG_SCSI_PDC_ADMA is not set
> # CONFIG_SCSI_SATA_QSTOR is not set
> # CONFIG_SCSI_SATA_PROMISE is not set
> # CONFIG_SCSI_SATA_SX4 is not set
> # CONFIG_SCSI_SATA_SIL is not set
> # CONFIG_SCSI_SATA_SIL24 is not set
> # CONFIG_SCSI_SATA_SIS is not set
> CONFIG_SCSI_SATA_ULI=y
> # CONFIG_SCSI_SATA_VIA is not set
> # CONFIG_SCSI_SATA_VITESSE is not set
> CONFIG_SCSI_SATA_INTEL_COMBINED=y
> # CONFIG_SCSI_BUSLOGIC is not set
> # CONFIG_SCSI_DMX3191D is not set
> # CONFIG_SCSI_EATA is not set
> # CONFIG_SCSI_EATA_PIO is not set
> # CONFIG_SCSI_FUTURE_DOMAIN is not set
> # CONFIG_SCSI_GDTH is not set
> # CONFIG_SCSI_IPS is not set
> # CONFIG_SCSI_INITIO is not set
> # CONFIG_SCSI_INIA100 is not set
> # CONFIG_SCSI_PPA is not set
> # CONFIG_SCSI_IMM is not set
> # CONFIG_SCSI_SYM53C8XX_2 is not set
> # CONFIG_SCSI_IPR is not set
> # CONFIG_SCSI_QLOGIC_FC is not set
> # CONFIG_SCSI_QLOGIC_1280 is not set
> CONFIG_SCSI_QLA2XXX=y
> # CONFIG_SCSI_QLA21XX is not set
> # CONFIG_SCSI_QLA22XX is not set
> # CONFIG_SCSI_QLA2300 is not set
> # CONFIG_SCSI_QLA2322 is not set
> # CONFIG_SCSI_QLA6312 is not set
> # CONFIG_SCSI_QLA24XX is not set
> # CONFIG_SCSI_LPFC is not set
> # CONFIG_SCSI_DC395x is not set
> # CONFIG_SCSI_DC390T is not set
> # CONFIG_SCSI_DEBUG is not set
>
> #
> # Multi-device support (RAID and LVM)
> #
> # CONFIG_MD is not set
>
> #
> # Fusion MPT device support
> #
> # CONFIG_FUSION is not set
> # CONFIG_FUSION_SPI is not set
> # CONFIG_FUSION_FC is not set
> # CONFIG_FUSION_SAS is not set
>
> #
> # IEEE 1394 (FireWire) support
> #
> # CONFIG_IEEE1394 is not set
>
> #
> # I2O device support
> #
> CONFIG_I2O=y
> CONFIG_I2O_EXT_ADAPTEC=y
> CONFIG_I2O_EXT_ADAPTEC_DMA64=y
> CONFIG_I2O_CONFIG=y
> CONFIG_I2O_CONFIG_OLD_IOCTL=y
> CONFIG_I2O_BUS=y
> CONFIG_I2O_BLOCK=y
> CONFIG_I2O_SCSI=y
> CONFIG_I2O_PROC=y
>
> #
> # Network device support
> #
> CONFIG_NETDEVICES=y
> CONFIG_DUMMY=y
> # CONFIG_BONDING is not set
> # CONFIG_EQUALIZER is not set
> # CONFIG_TUN is not set
> # CONFIG_NET_SB1000 is not set
>
> #
> # ARCnet devices
> #
> # CONFIG_ARCNET is not set
>
> #
> # PHY device support
> #
> # CONFIG_PHYLIB is not set
>
> #
> # Ethernet (10 or 100Mbit)
> #
> CONFIG_NET_ETHERNET=y
> CONFIG_MII=y
> # CONFIG_HAPPYMEAL is not set
> # CONFIG_SUNGEM is not set
> # CONFIG_CASSINI is not set
> # CONFIG_NET_VENDOR_3COM is not set
>
> #
> # Tulip family network device support
> #
> CONFIG_NET_TULIP=y
> # CONFIG_DE2104X is not set
> # CONFIG_TULIP is not set
> # CONFIG_DE4X5 is not set
> # CONFIG_WINBOND_840 is not set
> # CONFIG_DM9102 is not set
> CONFIG_ULI526X=m
> # CONFIG_HP100 is not set
> # CONFIG_NET_PCI is not set
> # CONFIG_NET_POCKET is not set
>
> #
> # Ethernet (1000 Mbit)
> #
> # CONFIG_ACENIC is not set
> # CONFIG_DL2K is not set
> # CONFIG_E1000 is not set
> # CONFIG_NS83820 is not set
> # CONFIG_HAMACHI is not set
> # CONFIG_YELLOWFIN is not set
> # CONFIG_R8169 is not set
> # CONFIG_SIS190 is not set
> # CONFIG_SKGE is not set
> # CONFIG_SK98LIN is not set
> # CONFIG_TIGON3 is not set
> # CONFIG_BNX2 is not set
>
> #
> # Ethernet (10000 Mbit)
> #
> # CONFIG_CHELSIO_T1 is not set
> # CONFIG_IXGB is not set
> # CONFIG_S2IO is not set
>
> #
> # Token Ring devices
> #
> # CONFIG_TR is not set
>
> #
> # Wireless LAN (non-hamradio)
> #
> # CONFIG_NET_RADIO is not set
>
> #
> # Wan interfaces
> #
> # CONFIG_WAN is not set
> # CONFIG_FDDI is not set
> # CONFIG_HIPPI is not set
> # CONFIG_PLIP is not set
> # CONFIG_PPP is not set
> # CONFIG_SLIP is not set
> # CONFIG_NET_FC is not set
> # CONFIG_SHAPER is not set
> # CONFIG_NETCONSOLE is not set
> # CONFIG_NETPOLL is not set
> # CONFIG_NET_POLL_CONTROLLER is not set
>
> #
> # ISDN subsystem
> #
> # CONFIG_ISDN is not set
>
> #
> # Telephony Support
> #
> # CONFIG_PHONE is not set
>
> #
> # Input device support
> #
> CONFIG_INPUT=y
>
> #
> # Userland interfaces
> #
> CONFIG_INPUT_MOUSEDEV=y
> CONFIG_INPUT_MOUSEDEV_PSAUX=y
> CONFIG_INPUT_MOUSEDEV_SCREEN_X=1280
> CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1024
> # CONFIG_INPUT_JOYDEV is not set
> # CONFIG_INPUT_TSDEV is not set
> CONFIG_INPUT_EVDEV=y
> # CONFIG_INPUT_EVBUG is not set
>
> #
> # Input Device Drivers
> #
> CONFIG_INPUT_KEYBOARD=y
> CONFIG_KEYBOARD_ATKBD=y
> # CONFIG_KEYBOARD_SUNKBD is not set
> # CONFIG_KEYBOARD_LKKBD is not set
> # CONFIG_KEYBOARD_XTKBD is not set
> # CONFIG_KEYBOARD_NEWTON is not set
> CONFIG_INPUT_MOUSE=y
> CONFIG_MOUSE_PS2=y
> # CONFIG_MOUSE_SERIAL is not set
> # CONFIG_MOUSE_VSXXXAA is not set
> # CONFIG_INPUT_JOYSTICK is not set
> # CONFIG_INPUT_TOUCHSCREEN is not set
> # CONFIG_INPUT_MISC is not set
>
> #
> # Hardware I/O ports
> #
> CONFIG_SERIO=y
> CONFIG_SERIO_I8042=y
> # CONFIG_SERIO_SERPORT is not set
> # CONFIG_SERIO_CT82C710 is not set
> # CONFIG_SERIO_PARKBD is not set
> # CONFIG_SERIO_PCIPS2 is not set
> CONFIG_SERIO_LIBPS2=y
> # CONFIG_SERIO_RAW is not set
> # CONFIG_GAMEPORT is not set
>
> #
> # Character devices
> #
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> CONFIG_HW_CONSOLE=y
> # CONFIG_SERIAL_NONSTANDARD is not set
>
> #
> # Serial drivers
> #
> CONFIG_SERIAL_8250=y
> # CONFIG_SERIAL_8250_CONSOLE is not set
> # CONFIG_SERIAL_8250_ACPI is not set
> CONFIG_SERIAL_8250_NR_UARTS=4
> # CONFIG_SERIAL_8250_EXTENDED is not set
>
> #
> # Non-8250 serial port support
> #
> CONFIG_SERIAL_CORE=y
> # CONFIG_SERIAL_JSM is not set
> CONFIG_UNIX98_PTYS=y
> CONFIG_LEGACY_PTYS=y
> CONFIG_LEGACY_PTY_COUNT=256
> CONFIG_PRINTER=y
> CONFIG_LP_CONSOLE=y
> # CONFIG_PPDEV is not set
> # CONFIG_TIPAR is not set
>
> #
> # IPMI
> #
> # CONFIG_IPMI_HANDLER is not set
>
> #
> # Watchdog Cards
> #
> # CONFIG_WATCHDOG is not set
> # CONFIG_HW_RANDOM is not set
> CONFIG_NVRAM=y
> CONFIG_RTC=y
> # CONFIG_DTLK is not set
> # CONFIG_R3964 is not set
> # CONFIG_APPLICOM is not set
>
> #
> # Ftape, the floppy tape device driver
> #
> # CONFIG_FTAPE is not set
> CONFIG_AGP=y
> CONFIG_AGP_AMD64=y
> # CONFIG_AGP_INTEL is not set
> # CONFIG_DRM is not set
> # CONFIG_MWAVE is not set
> # CONFIG_RAW_DRIVER is not set
> CONFIG_HPET=y
> # CONFIG_HPET_RTC_IRQ is not set
> CONFIG_HPET_MMAP=y
> # CONFIG_HANGCHECK_TIMER is not set
>
> #
> # TPM devices
> #
> # CONFIG_TCG_TPM is not set
> # CONFIG_TELCLOCK is not set
>
> #
> # I2C support
> #
> CONFIG_I2C=y
> CONFIG_I2C_CHARDEV=y
>
> #
> # I2C Algorithms
> #
> CONFIG_I2C_ALGOBIT=y
> # CONFIG_I2C_ALGOPCF is not set
> # CONFIG_I2C_ALGOPCA is not set
>
> #
> # I2C Hardware Bus support
> #
> # CONFIG_I2C_ALI1535 is not set
> CONFIG_I2C_ALI1563=y
> # CONFIG_I2C_ALI15X3 is not set
> # CONFIG_I2C_AMD756 is not set
> # CONFIG_I2C_AMD8111 is not set
> # CONFIG_I2C_I801 is not set
> # CONFIG_I2C_I810 is not set
> # CONFIG_I2C_PIIX4 is not set
> CONFIG_I2C_ISA=y
> # CONFIG_I2C_NFORCE2 is not set
> # CONFIG_I2C_PARPORT is not set
> # CONFIG_I2C_PARPORT_LIGHT is not set
> # CONFIG_I2C_PROSAVAGE is not set
> # CONFIG_I2C_SAVAGE4 is not set
> # CONFIG_SCx200_ACB is not set
> # CONFIG_I2C_SIS5595 is not set
> # CONFIG_I2C_SIS630 is not set
> # CONFIG_I2C_SIS96X is not set
> # CONFIG_I2C_STUB is not set
> # CONFIG_I2C_VIA is not set
> # CONFIG_I2C_VIAPRO is not set
> # CONFIG_I2C_VOODOO3 is not set
> # CONFIG_I2C_PCA_ISA is not set
>
> #
> # Miscellaneous I2C Chip support
> #
> # CONFIG_SENSORS_DS1337 is not set
> # CONFIG_SENSORS_DS1374 is not set
> CONFIG_SENSORS_EEPROM=y
> # CONFIG_SENSORS_PCF8574 is not set
> # CONFIG_SENSORS_PCA9539 is not set
> # CONFIG_SENSORS_PCF8591 is not set
> # CONFIG_SENSORS_RTC8564 is not set
> # CONFIG_SENSORS_MAX6875 is not set
> # CONFIG_RTC_X1205_I2C is not set
> # CONFIG_I2C_DEBUG_CORE is not set
> # CONFIG_I2C_DEBUG_ALGO is not set
> # CONFIG_I2C_DEBUG_BUS is not set
> # CONFIG_I2C_DEBUG_CHIP is not set
>
> #
> # Dallas's 1-wire bus
> #
> # CONFIG_W1 is not set
>
> #
> # Hardware Monitoring support
> #
> CONFIG_HWMON=y
> CONFIG_HWMON_VID=y
> # CONFIG_SENSORS_ADM1021 is not set
> # CONFIG_SENSORS_ADM1025 is not set
> # CONFIG_SENSORS_ADM1026 is not set
> # CONFIG_SENSORS_ADM1031 is not set
> # CONFIG_SENSORS_ADM9240 is not set
> # CONFIG_SENSORS_ASB100 is not set
> # CONFIG_SENSORS_ATXP1 is not set
> # CONFIG_SENSORS_DS1621 is not set
> # CONFIG_SENSORS_FSCHER is not set
> # CONFIG_SENSORS_FSCPOS is not set
> # CONFIG_SENSORS_GL518SM is not set
> # CONFIG_SENSORS_GL520SM is not set
> # CONFIG_SENSORS_IT87 is not set
> # CONFIG_SENSORS_LM63 is not set
> CONFIG_SENSORS_LM75=y
> # CONFIG_SENSORS_LM77 is not set
> # CONFIG_SENSORS_LM78 is not set
> # CONFIG_SENSORS_LM80 is not set
> # CONFIG_SENSORS_LM83 is not set
> # CONFIG_SENSORS_LM85 is not set
> # CONFIG_SENSORS_LM87 is not set
> # CONFIG_SENSORS_LM90 is not set
> # CONFIG_SENSORS_LM92 is not set
> # CONFIG_SENSORS_MAX1619 is not set
> # CONFIG_SENSORS_PC87360 is not set
> # CONFIG_SENSORS_SIS5595 is not set
> # CONFIG_SENSORS_SMSC47M1 is not set
> # CONFIG_SENSORS_SMSC47B397 is not set
> # CONFIG_SENSORS_VIA686A is not set
> # CONFIG_SENSORS_W83781D is not set
> # CONFIG_SENSORS_W83792D is not set
> # CONFIG_SENSORS_W83L785TS is not set
> CONFIG_SENSORS_W83627HF=y
> # CONFIG_SENSORS_W83627EHF is not set
> # CONFIG_SENSORS_HDAPS is not set
> # CONFIG_HWMON_DEBUG_CHIP is not set
>
> #
> # Misc devices
> #
> # CONFIG_IBM_ASM is not set
>
> #
> # Multimedia Capabilities Port drivers
> #
>
> #
> # Multimedia devices
> #
> # CONFIG_VIDEO_DEV is not set
>
> #
> # Digital Video Broadcasting Devices
> #
> # CONFIG_DVB is not set
>
> #
> # Graphics support
> #
> CONFIG_FB=y
> CONFIG_FB_CFB_FILLRECT=y
> CONFIG_FB_CFB_COPYAREA=y
> CONFIG_FB_CFB_IMAGEBLIT=y
> # CONFIG_FB_MACMODES is not set
> # CONFIG_FB_MODE_HELPERS is not set
> # CONFIG_FB_TILEBLITTING is not set
> # CONFIG_FB_CIRRUS is not set
> # CONFIG_FB_PM2 is not set
> # CONFIG_FB_CYBER2000 is not set
> # CONFIG_FB_ARC is not set
> # CONFIG_FB_ASILIANT is not set
> # CONFIG_FB_IMSTT is not set
> # CONFIG_FB_VGA16 is not set
> CONFIG_FB_VESA=y
> CONFIG_VIDEO_SELECT=y
> # CONFIG_FB_HGA is not set
> # CONFIG_FB_S1D13XXX is not set
> # CONFIG_FB_NVIDIA is not set
> # CONFIG_FB_RIVA is not set
> # CONFIG_FB_MATROX is not set
> # CONFIG_FB_RADEON_OLD is not set
> # CONFIG_FB_RADEON is not set
> # CONFIG_FB_ATY128 is not set
> # CONFIG_FB_ATY is not set
> # CONFIG_FB_SAVAGE is not set
> # CONFIG_FB_SIS is not set
> # CONFIG_FB_NEOMAGIC is not set
> # CONFIG_FB_KYRO is not set
> # CONFIG_FB_3DFX is not set
> # CONFIG_FB_VOODOO1 is not set
> # CONFIG_FB_CYBLA is not set
> # CONFIG_FB_TRIDENT is not set
> # CONFIG_FB_PM3 is not set
> # CONFIG_FB_GEODE is not set
> # CONFIG_FB_VIRTUAL is not set
>
> #
> # Console display driver support
> #
> CONFIG_VGA_CONSOLE=y
> CONFIG_DUMMY_CONSOLE=y
> CONFIG_FRAMEBUFFER_CONSOLE=y
> # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
> # CONFIG_FONTS is not set
> CONFIG_FONT_8x8=y
> CONFIG_FONT_8x16=y
>
> #
> # Logo configuration
> #
> CONFIG_LOGO=y
> # CONFIG_LOGO_LINUX_MONO is not set
> # CONFIG_LOGO_LINUX_VGA16 is not set
> CONFIG_LOGO_LINUX_CLUT224=y
> # CONFIG_BACKLIGHT_LCD_SUPPORT is not set
>
> #
> # Sound
> #
> CONFIG_SOUND=y
>
> #
> # Advanced Linux Sound Architecture
> #
> CONFIG_SND=y
> CONFIG_SND_AC97_CODEC=y
> CONFIG_SND_AC97_BUS=y
> CONFIG_SND_TIMER=y
> CONFIG_SND_PCM=y
> CONFIG_SND_SEQUENCER=y
> CONFIG_SND_SEQ_DUMMY=y
> CONFIG_SND_OSSEMUL=y
> CONFIG_SND_MIXER_OSS=y
> CONFIG_SND_PCM_OSS=y
> CONFIG_SND_SEQUENCER_OSS=y
> CONFIG_SND_RTCTIMER=y
> CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
> # CONFIG_SND_VERBOSE_PRINTK is not set
> # CONFIG_SND_DEBUG is not set
>
> #
> # Generic devices
> #
> # CONFIG_SND_DUMMY is not set
> # CONFIG_SND_VIRMIDI is not set
> # CONFIG_SND_MTPAV is not set
> # CONFIG_SND_SERIAL_U16550 is not set
> # CONFIG_SND_MPU401 is not set
>
> #
> # PCI devices
> #
> # CONFIG_SND_ALI5451 is not set
> # CONFIG_SND_ATIIXP is not set
> # CONFIG_SND_ATIIXP_MODEM is not set
> # CONFIG_SND_AU8810 is not set
> # CONFIG_SND_AU8820 is not set
> # CONFIG_SND_AU8830 is not set
> # CONFIG_SND_AZT3328 is not set
> # CONFIG_SND_BT87X is not set
> # CONFIG_SND_CS46XX is not set
> # CONFIG_SND_CS4281 is not set
> # CONFIG_SND_EMU10K1 is not set
> # CONFIG_SND_EMU10K1X is not set
> # CONFIG_SND_CA0106 is not set
> # CONFIG_SND_KORG1212 is not set
> # CONFIG_SND_MIXART is not set
> # CONFIG_SND_NM256 is not set
> # CONFIG_SND_RME32 is not set
> # CONFIG_SND_RME96 is not set
> # CONFIG_SND_RME9652 is not set
> # CONFIG_SND_HDSP is not set
> # CONFIG_SND_HDSPM is not set
> # CONFIG_SND_TRIDENT is not set
> # CONFIG_SND_YMFPCI is not set
> # CONFIG_SND_AD1889 is not set
> # CONFIG_SND_ALS4000 is not set
> # CONFIG_SND_CMIPCI is not set
> # CONFIG_SND_ENS1370 is not set
> # CONFIG_SND_ENS1371 is not set
> # CONFIG_SND_ES1938 is not set
> # CONFIG_SND_ES1968 is not set
> # CONFIG_SND_MAESTRO3 is not set
> # CONFIG_SND_FM801 is not set
> # CONFIG_SND_ICE1712 is not set
> # CONFIG_SND_ICE1724 is not set
> CONFIG_SND_INTEL8X0=y
> # CONFIG_SND_INTEL8X0M is not set
> # CONFIG_SND_SONICVIBES is not set
> # CONFIG_SND_VIA82XX is not set
> # CONFIG_SND_VIA82XX_MODEM is not set
> # CONFIG_SND_VX222 is not set
> # CONFIG_SND_HDA_INTEL is not set
>
> #
> # USB devices
> #
> # CONFIG_SND_USB_AUDIO is not set
> # CONFIG_SND_USB_USX2Y is not set
>
> #
> # Open Sound System
> #
> # CONFIG_SOUND_PRIME is not set
>
> #
> # USB support
> #
> CONFIG_USB_ARCH_HAS_HCD=y
> CONFIG_USB_ARCH_HAS_OHCI=y
> CONFIG_USB=y
> # CONFIG_USB_DEBUG is not set
>
> #
> # Miscellaneous USB options
> #
> CONFIG_USB_DEVICEFS=y
> # CONFIG_USB_BANDWIDTH is not set
> CONFIG_USB_DYNAMIC_MINORS=y
> CONFIG_USB_SUSPEND=y
> # CONFIG_USB_OTG is not set
>
> #
> # USB Host Controller Drivers
> #
> CONFIG_USB_EHCI_HCD=y
> CONFIG_USB_EHCI_SPLIT_ISO=y
> CONFIG_USB_EHCI_ROOT_HUB_TT=y
> # CONFIG_USB_ISP116X_HCD is not set
> CONFIG_USB_OHCI_HCD=y
> # CONFIG_USB_OHCI_BIG_ENDIAN is not set
> CONFIG_USB_OHCI_LITTLE_ENDIAN=y
> # CONFIG_USB_UHCI_HCD is not set
> # CONFIG_USB_SL811_HCD is not set
>
> #
> # USB Device Class drivers
> #
> # CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
> # CONFIG_USB_ACM is not set
> # CONFIG_USB_PRINTER is not set
>
> #
> # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
> #
>
> #
> # may also be needed; see USB_STORAGE Help for more information
> #
> CONFIG_USB_STORAGE=y
> # CONFIG_USB_STORAGE_DEBUG is not set
> # CONFIG_USB_STORAGE_DATAFAB is not set
> # CONFIG_USB_STORAGE_FREECOM is not set
> # CONFIG_USB_STORAGE_ISD200 is not set
> # CONFIG_USB_STORAGE_DPCM is not set
> # CONFIG_USB_STORAGE_USBAT is not set
> # CONFIG_USB_STORAGE_SDDR09 is not set
> # CONFIG_USB_STORAGE_SDDR55 is not set
> # CONFIG_USB_STORAGE_JUMPSHOT is not set
>
> #
> # USB Input Devices
> #
> # CONFIG_USB_HID is not set
>
> #
> # USB HID Boot Protocol drivers
> #
> # CONFIG_USB_KBD is not set
> # CONFIG_USB_MOUSE is not set
> # CONFIG_USB_AIPTEK is not set
> # CONFIG_USB_WACOM is not set
> # CONFIG_USB_ACECAD is not set
> # CONFIG_USB_KBTAB is not set
> # CONFIG_USB_POWERMATE is not set
> # CONFIG_USB_MTOUCH is not set
> # CONFIG_USB_ITMTOUCH is not set
> # CONFIG_USB_EGALAX is not set
> # CONFIG_USB_YEALINK is not set
> # CONFIG_USB_XPAD is not set
> # CONFIG_USB_ATI_REMOTE is not set
> # CONFIG_USB_KEYSPAN_REMOTE is not set
> # CONFIG_USB_APPLETOUCH is not set
>
> #
> # USB Imaging devices
> #
> # CONFIG_USB_MDC800 is not set
> # CONFIG_USB_MICROTEK is not set
>
> #
> # USB Multimedia devices
> #
> # CONFIG_USB_DABUSB is not set
>
> #
> # Video4Linux support is needed for USB Multimedia device support
> #
>
> #
> # USB Network Adapters
> #
> # CONFIG_USB_CATC is not set
> # CONFIG_USB_KAWETH is not set
> # CONFIG_USB_PEGASUS is not set
> # CONFIG_USB_RTL8150 is not set
> # CONFIG_USB_USBNET is not set
> CONFIG_USB_MON=y
>
> #
> # USB port drivers
> #
> # CONFIG_USB_USS720 is not set
>
> #
> # USB Serial Converter support
> #
> # CONFIG_USB_SERIAL is not set
>
> #
> # USB Miscellaneous drivers
> #
> # CONFIG_USB_EMI62 is not set
> # CONFIG_USB_EMI26 is not set
> # CONFIG_USB_AUERSWALD is not set
> # CONFIG_USB_RIO500 is not set
> # CONFIG_USB_LEGOTOWER is not set
> # CONFIG_USB_LCD is not set
> # CONFIG_USB_LED is not set
> # CONFIG_USB_CYTHERM is not set
> # CONFIG_USB_PHIDGETKIT is not set
> # CONFIG_USB_PHIDGETSERVO is not set
> # CONFIG_USB_IDMOUSE is not set
> # CONFIG_USB_SISUSBVGA is not set
> # CONFIG_USB_LD is not set
> # CONFIG_USB_TEST is not set
>
> #
> # USB DSL modem support
> #
>
> #
> # USB Gadget Support
> #
> # CONFIG_USB_GADGET is not set
>
> #
> # MMC/SD Card support
> #
> # CONFIG_MMC is not set
>
> #
> # InfiniBand support
> #
> # CONFIG_INFINIBAND is not set
>
> #
> # SN Devices
> #
>
> #
> # Firmware Drivers
> #
> # CONFIG_EDD is not set
> # CONFIG_DELL_RBU is not set
> # CONFIG_DCDBAS is not set
>
> #
> # File systems
> #
> CONFIG_EXT2_FS=y
> # CONFIG_EXT2_FS_XATTR is not set
> # CONFIG_EXT2_FS_XIP is not set
> CONFIG_EXT3_FS=y
> # CONFIG_EXT3_FS_XATTR is not set
> CONFIG_JBD=y
> # CONFIG_JBD_DEBUG is not set
> CONFIG_REISERFS_FS=y
> # CONFIG_REISERFS_CHECK is not set
> # CONFIG_REISERFS_PROC_INFO is not set
> # CONFIG_REISERFS_FS_XATTR is not set
> # CONFIG_JFS_FS is not set
> CONFIG_FS_POSIX_ACL=y
> # CONFIG_XFS_FS is not set
> # CONFIG_MINIX_FS is not set
> # CONFIG_ROMFS_FS is not set
> CONFIG_INOTIFY=y
> # CONFIG_QUOTA is not set
> CONFIG_DNOTIFY=y
> # CONFIG_AUTOFS_FS is not set
> CONFIG_AUTOFS4_FS=y
> CONFIG_FUSE_FS=y
>
> #
> # CD-ROM/DVD Filesystems
> #
> CONFIG_ISO9660_FS=y
> CONFIG_JOLIET=y
> CONFIG_ZISOFS=y
> CONFIG_ZISOFS_FS=y
> CONFIG_UDF_FS=y
> CONFIG_UDF_NLS=y
>
> #
> # DOS/FAT/NT Filesystems
> #
> CONFIG_FAT_FS=y
> CONFIG_MSDOS_FS=y
> CONFIG_VFAT_FS=y
> CONFIG_FAT_DEFAULT_CODEPAGE=437
> CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
> CONFIG_NTFS_FS=y
> # CONFIG_NTFS_DEBUG is not set
> CONFIG_NTFS_RW=y
>
> #
> # Pseudo filesystems
> #
> CONFIG_PROC_FS=y
> CONFIG_PROC_KCORE=y
> CONFIG_SYSFS=y
> CONFIG_TMPFS=y
> # CONFIG_HUGETLBFS is not set
> # CONFIG_HUGETLB_PAGE is not set
> CONFIG_RAMFS=y
> # CONFIG_RELAYFS_FS is not set
>
> #
> # Miscellaneous filesystems
> #
> # CONFIG_ADFS_FS is not set
> # CONFIG_AFFS_FS is not set
> # CONFIG_HFS_FS is not set
> # CONFIG_HFSPLUS_FS is not set
> # CONFIG_BEFS_FS is not set
> # CONFIG_BFS_FS is not set
> # CONFIG_EFS_FS is not set
> # CONFIG_CRAMFS is not set
> # CONFIG_VXFS_FS is not set
> # CONFIG_HPFS_FS is not set
> # CONFIG_QNX4FS_FS is not set
> # CONFIG_SYSV_FS is not set
> # CONFIG_UFS_FS is not set
>
> #
> # Network File Systems
> #
> CONFIG_NFS_FS=y
> CONFIG_NFS_V3=y
> # CONFIG_NFS_V3_ACL is not set
> CONFIG_NFS_V4=y
> CONFIG_NFS_DIRECTIO=y
> CONFIG_NFSD=y
> CONFIG_NFSD_V3=y
> # CONFIG_NFSD_V3_ACL is not set
> CONFIG_NFSD_V4=y
> CONFIG_NFSD_TCP=y
> CONFIG_LOCKD=y
> CONFIG_LOCKD_V4=y
> CONFIG_EXPORTFS=y
> CONFIG_NFS_COMMON=y
> CONFIG_SUNRPC=y
> CONFIG_SUNRPC_GSS=y
> CONFIG_RPCSEC_GSS_KRB5=y
> # CONFIG_RPCSEC_GSS_SPKM3 is not set
> CONFIG_SMB_FS=y
> # CONFIG_SMB_NLS_DEFAULT is not set
> CONFIG_CIFS=y
> # CONFIG_CIFS_STATS is not set
> # CONFIG_CIFS_XATTR is not set
> # CONFIG_CIFS_EXPERIMENTAL is not set
> # CONFIG_NCP_FS is not set
> # CONFIG_CODA_FS is not set
> # CONFIG_AFS_FS is not set
> # CONFIG_9P_FS is not set
>
> #
> # Partition Types
> #
> # CONFIG_PARTITION_ADVANCED is not set
> CONFIG_MSDOS_PARTITION=y
>
> #
> # Native Language Support
> #
> CONFIG_NLS=y
> CONFIG_NLS_DEFAULT="utf8"
> CONFIG_NLS_CODEPAGE_437=y
> # CONFIG_NLS_CODEPAGE_737 is not set
> # CONFIG_NLS_CODEPAGE_775 is not set
> CONFIG_NLS_CODEPAGE_850=y
> # CONFIG_NLS_CODEPAGE_852 is not set
> # CONFIG_NLS_CODEPAGE_855 is not set
> # CONFIG_NLS_CODEPAGE_857 is not set
> # CONFIG_NLS_CODEPAGE_860 is not set
> # CONFIG_NLS_CODEPAGE_861 is not set
> # CONFIG_NLS_CODEPAGE_862 is not set
> # CONFIG_NLS_CODEPAGE_863 is not set
> # CONFIG_NLS_CODEPAGE_864 is not set
> # CONFIG_NLS_CODEPAGE_865 is not set
> # CONFIG_NLS_CODEPAGE_866 is not set
> # CONFIG_NLS_CODEPAGE_869 is not set
> # CONFIG_NLS_CODEPAGE_936 is not set
> # CONFIG_NLS_CODEPAGE_950 is not set
> # CONFIG_NLS_CODEPAGE_932 is not set
> # CONFIG_NLS_CODEPAGE_949 is not set
> # CONFIG_NLS_CODEPAGE_874 is not set
> # CONFIG_NLS_ISO8859_8 is not set
> # CONFIG_NLS_CODEPAGE_1250 is not set
> # CONFIG_NLS_CODEPAGE_1251 is not set
> # CONFIG_NLS_ASCII is not set
> CONFIG_NLS_ISO8859_1=y
> # CONFIG_NLS_ISO8859_2 is not set
> # CONFIG_NLS_ISO8859_3 is not set
> # CONFIG_NLS_ISO8859_4 is not set
> # CONFIG_NLS_ISO8859_5 is not set
> # CONFIG_NLS_ISO8859_6 is not set
> # CONFIG_NLS_ISO8859_7 is not set
> # CONFIG_NLS_ISO8859_9 is not set
> # CONFIG_NLS_ISO8859_13 is not set
> # CONFIG_NLS_ISO8859_14 is not set
> # CONFIG_NLS_ISO8859_15 is not set
> # CONFIG_NLS_KOI8_R is not set
> # CONFIG_NLS_KOI8_U is not set
> CONFIG_NLS_UTF8=y
>
> #
> # Instrumentation Support
> #
> # CONFIG_PROFILING is not set
> # CONFIG_KPROBES is not set
>
> #
> # Kernel hacking
> #
> # CONFIG_PRINTK_TIME is not set
> CONFIG_DEBUG_KERNEL=y
> CONFIG_MAGIC_SYSRQ=y
> CONFIG_LOG_BUF_SHIFT=15
> # CONFIG_DETECT_SOFTLOCKUP is not set
> # CONFIG_SCHEDSTATS is not set
> # CONFIG_DEBUG_SLAB is not set
> # CONFIG_DEBUG_PREEMPT is not set
> # CONFIG_DEBUG_SPINLOCK is not set
> # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
> # CONFIG_DEBUG_KOBJECT is not set
> # CONFIG_DEBUG_INFO is not set
> # CONFIG_DEBUG_FS is not set
> # CONFIG_DEBUG_VM is not set
> # CONFIG_FRAME_POINTER is not set
> # CONFIG_RCU_TORTURE_TEST is not set
> # CONFIG_INIT_DEBUG is not set
> # CONFIG_IOMMU_DEBUG is not set
>
> #
> # Security options
> #
> # CONFIG_KEYS is not set
> # CONFIG_SECURITY is not set
>
> #
> # Cryptographic options
> #
> CONFIG_CRYPTO=y
> # CONFIG_CRYPTO_HMAC is not set
> # CONFIG_CRYPTO_NULL is not set
> # CONFIG_CRYPTO_MD4 is not set
> CONFIG_CRYPTO_MD5=y
> # CONFIG_CRYPTO_SHA1 is not set
> # CONFIG_CRYPTO_SHA256 is not set
> # CONFIG_CRYPTO_SHA512 is not set
> # CONFIG_CRYPTO_WP512 is not set
> # CONFIG_CRYPTO_TGR192 is not set
> CONFIG_CRYPTO_DES=y
> # CONFIG_CRYPTO_BLOWFISH is not set
> # CONFIG_CRYPTO_TWOFISH is not set
> # CONFIG_CRYPTO_SERPENT is not set
> # CONFIG_CRYPTO_AES_X86_64 is not set
> # CONFIG_CRYPTO_CAST5 is not set
> # CONFIG_CRYPTO_CAST6 is not set
> # CONFIG_CRYPTO_TEA is not set
> # CONFIG_CRYPTO_ARC4 is not set
> # CONFIG_CRYPTO_KHAZAD is not set
> # CONFIG_CRYPTO_ANUBIS is not set
> # CONFIG_CRYPTO_DEFLATE is not set
> # CONFIG_CRYPTO_MICHAEL_MIC is not set
> # CONFIG_CRYPTO_CRC32C is not set
> # CONFIG_CRYPTO_TEST is not set
>
> #
> # Hardware crypto devices
> #
>
> #
> # Library routines
> #
> # CONFIG_CRC_CCITT is not set
> # CONFIG_CRC16 is not set
> CONFIG_CRC32=y
> # CONFIG_LIBCRC32C is not set
> CONFIG_ZLIB_INFLATE=y
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
