Attached are boot messages and panic captured via serial console, as well as the system config. -- Andreas Steinmetz SPAMmers use [email protected]
Bootdata ok (command line is BOOT_IMAGE=2.6.15rc6s root=301 video=radeonfb:off console=ttyS0,115200 console=tty0) Linux version 2.6.15-rc6top (root@gringo) (gcc version 3.4.4) #1 SMP PREEMPT Thu Dec 22 14:23:34 CET 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable) BIOS-e820: 00000000bfff0000 - 00000000bffff000 (ACPI data) BIOS-e820: 00000000bffff000 - 00000000c0000000 (ACPI NVS) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000140000000 (usable) SRAT: PXM 0 -> APIC 0 -> Node 0 SRAT: PXM 1 -> APIC 1 -> Node 1 ACPI: [SRAT:0x00] ignored 2 entries of 4 found SRAT: Node 0 PXM 0 100000-80000000 SRAT: Node 1 PXM 1 80000000-c0000000 SRAT: Node 1 PXM 1 80000000-140000000 SRAT: Node 0 PXM 0 0-80000000 Bootmem setup node 0 0000000000000000-0000000080000000 Bootmem setup node 1 0000000080000000-0000000140000000 ACPI: PM-Timer IO Port: 0x5008 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:5 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:5 APIC version 16 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x03] address[0xfe9ff000] gsi_base[24]) IOAPIC[1]: apic_id 3, version 17, address 0xfe9ff000, GSI 24-27 ACPI: IOAPIC (id[0x04] address[0xfe9fe000] gsi_base[28]) IOAPIC[2]: apic_id 4, version 17, address 0xfe9fe000, GSI 28-31 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Setting APIC routing to flat ACPI: HPET id: 0x102282a0 base: 0xfec01000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at c4000000 (gap: c0000000:3f780000) Checking aperture... CPU 0: aperture @ f0000000 size 128 MB CPU 1: aperture @ f0000000 size 128 MB Built 2 zonelists Kernel command line: BOOT_IMAGE=2.6.15rc6s root=301 video=radeonfb:off console=ttyS0,115200 console=tty0 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 14.318180 MHz HPET timer. time.c: Detected 1992.254 MHz processor. Console: colour VGA+ 80x50 Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) Memory: 4102684k/5242880k available (4188k kernel code, 91168k reserved, 1774k data, 280k init) Calibrating delay using timer specific routine.. 3988.45 BogoMIPS (lpj=1994226) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0(1) -> Node 0 -> Core 0 mtrr: v2.0 (20020519) Using local APIC timer interrupts. Detected 12.451 MHz APIC timer. Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 3983.84 BogoMIPS (lpj=1991921) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1(1) -> Node 1 -> Core 0 AMD Opteron(tm) Processor 246 stepping 08 CPU 1: Syncing TSC to CPU 0. CPU 1: synchronized TSC with CPU 0 (last diff -4 cycles, maxerr 1073 cycles) Brought up 2 CPUs time.c: Using HPET based timekeeping. testing NMI watchdog ... OK. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) ACPI: PCI Root Bridge [PCIB] (0000:04) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 14 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report hpet0: at MMIO 0xfec01000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0 hpet0: 3 32-bit timers, 14318180 Hz agpgart: Detected AMD 8151 AGP Bridge rev B2 agpgart: AGP aperture is 128M @ 0xf0000000 PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture pnp: 00:09: ioport range 0x680-0x6ff has been reserved pnp: 00:09: ioport range 0x295-0x296 has been reserved PCI: Bridge: 0000:00:06.0 IO window: 6000-7fff MEM window: fe200000-fe3fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0a.0 IO window: 8000-9fff MEM window: fe400000-fe4fffff PREFETCH window: cde00000-cdefffff PCI: Bridge: 0000:00:0b.0 IO window: a000-afff MEM window: fe500000-fe8fffff PREFETCH window: cdf00000-cdffffff PCI: Bridge: 0000:04:01.0 IO window: c000-cfff MEM window: fea00000-feafffff PREFETCH window: ce100000-ee0fffff IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ audit: initializing netlink socket (disabled) audit(1135374123.884:1): initialized Installing knfsd (copyright (C) 1996 [email protected]). SELinux: Registering netfilter hooks Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered PCI: MSI quirk detected. pci_msi_quirk set. PCI: MSI quirk detected. pci_msi_quirk set. ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Processor [CPU1] (supports 8 throttling states) lp: driver loaded but no devices found Real Time Clock Driver v1.12 Non-volatile memory driver v1.2 hw_random: AMD768 system management I/O registers at 0x5000. hw_random hardware driver 1.0.0 loaded Linux agpgart interface v0.101 (c) Dave Jones [drm] Initialized drm 1.0.0 20040925 GSI 16 sharing vector 0xA9 and IRQ 16 ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [drm] Initialized radeon 1.19.0 20050911 on minor 0: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) pktcdvd: v0.2.0a 2004-07-14 Jens Axboe ([email protected]) and [email protected] Intel(R) PRO/1000 Network Driver - version 6.1.16-k2-NAPI Copyright (c) 1999-2005 Intel Corporation. GSI 17 sharing vector 0xB1 and IRQ 17 ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 28 (level, low) -> IRQ 17 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection GSI 18 sharing vector 0xB9 and IRQ 18 ACPI: PCI Interrupt 0000:03:03.1[B] -> GSI 29 (level, low) -> IRQ 18 e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection tg3.c:v3.45 (Dec 13, 2005) GSI 19 sharing vector 0xC1 and IRQ 19 ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 24 (level, low) -> IRQ 19 eth2: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCI:33MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:28:25:e3 eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth2: dma_rwctrl[763f0000] PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). CSLIP: code copyright 1989 Regents of the University of California. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD8111: IDE controller at PCI slot 0000:00:07.1 AMD8111: chipset revision 3 AMD8111: not 100% native mode: will probe irqs later AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio hda: WDC WD2500JB-32FUA0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: WDC WD2500JB-32FUA0, ATA DISK drive ide1 at 0x170-0x177,0x376 on irq 15 PDC20268: IDE controller at PCI slot 0000:02:08.0 GSI 20 sharing vector 0xC9 and IRQ 20 ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 27 (level, low) -> IRQ 20 PDC20268: chipset revision 2 PDC20268: ROM enabled at 0xfe4e0000 PDC20268: 100% native mode on irq 20 ide2: BM-DMA at 0x8800-0x8807, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at 0x8808-0x880f, BIOS settings: hdg:pio, hdh:pio hde: WDC WD2500JB-32FUA0, ATA DISK drive ide2 at 0x9800-0x9807,0x9402 on irq 20 hdg: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive ide3 at 0x9000-0x9007,0x8c02 on irq 20 hda: max request size: 1024KiB hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 > hdc: max request size: 1024KiB hdc: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100) hdc: cache flushes supported hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 hdc7 > hde: max request size: 1024KiB hde: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100) hde: cache flushes supported hde: hde1 hde2 hde3 hde4 < hde5 hde6 hde7 > hdg: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 st: Version 20050830, fixed bufsize 32768, s/g segs 256 ohci1394: $Rev: 1313 $ Ben Collins <[email protected]> GSI 21 sharing vector 0xD1 and IRQ 21 ACPI: PCI Interrupt 0000:01:0c.0[A] -> GSI 19 (level, low) -> IRQ 21 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[fe3fd000-fe3fd7ff] Max Packet=[2048] video1394: Installed video1394 module ieee1394: raw1394: /dev/raw1394 device initialized sbp2: $Rev: 1306 $ Ben Collins <[email protected]> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance usbmon: debugfs is not available GSI 22 sharing vector 0xD9 and IRQ 22 ACPI: PCI Interrupt 0000:01:0a.2[C] -> GSI 18 (level, low) -> IRQ 22 ehci_hcd 0000:01:0a.2: EHCI Host Controller ehci_hcd 0000:01:0a.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:01:0a.2: irq 22, io mem 0xfe3fdc00 ehci_hcd 0000:01:0a.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected ACPI: PCI Interrupt 0000:01:00.0[D] -> GSI 19 (level, low) -> IRQ 21 ohci_hcd 0000:01:00.0: OHCI Host Controller ohci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:01:00.0: irq 21, io mem 0xfe3fe000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected ACPI: PCI Interrupt 0000:01:00.1[D] -> GSI 19 (level, low) -> IRQ 21 ohci_hcd 0000:01:00.1: OHCI Host Controller ohci_hcd 0000:01:00.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:01:00.1: irq 21, io mem 0xfe3ff000 hub 3-0:1.0: USB hub found hub 3-0:1.0: 3 ports detected ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 16 (level, low) -> IRQ 16 ohci_hcd 0000:01:0a.0: OHCI Host Controller ohci_hcd 0000:01:0a.0: new USB bus registered, assigned bus number 4 ohci_hcd 0000:01:0a.0: irq 16, io mem 0xfe3fb000 hub 4-0:1.0: USB hub found hub 4-0:1.0: 3 ports detected hub 4-0:1.0: over-current change on port 1 GSI 23 sharing vector 0xE1 and IRQ 23 ACPI: PCI Interrupt 0000:01:0a.1[B] -> GSI 17 (level, low) -> IRQ 23 ohci_hcd 0000:01:0a.1: OHCI Host Controller ohci_hcd 0000:01:0a.1: new USB bus registered, assigned bus number 5 ohci_hcd 0000:01:0a.1: irq 23, io mem 0xfe3fc000 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 4-1: new full speed USB device using ohci_hcd and address 2 hub 4-0:1.0: over-current change on port 2 USB Universal Host Controller Interface driver v2.3 Initializing USB Mass Storage driver... hub 4-0:1.0: over-current change on port 3 scsi0 : SCSI emulation for USB Mass Storage devices hub 5-0:1.0: over-current change on port 1 usbcore: registered new driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice md: raid5 personality registered as nr 4 raid5: automatically using best checksumming function: generic_sse generic_sse: 6072.000 MB/sec raid5: using function: generic_sse (6072.000 MB/sec) md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected] Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC). ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 23 input: AT Translated Set 2 keyboard as /class/input/input0 intel8x0_measure_ac97_clock: measured 51379 usecs intel8x0: clocking to 48000 ALSA device list: #0: AMD AMD8111 with AD1981B at 0xb800, irq 23 u32 classifier OLD policer on NET: Registered protocol family 2 IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered ip_conntrack version 2.4 (8192 buckets, 65536 max) - 288 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team hub 5-0:1.0: over-current change on port 2 ipt_recent v0.3.1: Stephen Frost <[email protected]>. http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 802.1Q VLAN Support v1.8 Ben Greear <[email protected]> All bugs added by David S. Miller <[email protected]> input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 md: Autodetecting RAID arrays. md: autorun ... md: considering hde6 ... md: adding hde6 ... md: hde3 has different UUID to hde6 md: adding hdc6 ... md: hdc3 has different UUID to hde6 md: adding hda6 ... md: hda3 has different UUID to hde6 md: created md1 md: bind<hda6> md: bind<hdc6> md: bind<hde6> md: running: <hde6><hdc6><hda6> raid5: device hde6 operational as raid disk 2 raid5: device hdc6 operational as raid disk 1 raid5: device hda6 operational as raid disk 0 raid5: allocated 3212kB for md1 raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 0 RAID5 conf printout: --- rd:3 wd:3 fd:0 disk 0, o:1, dev:hda6 disk 1, o:1, dev:hdc6 disk 2, o:1, dev:hde6 md: considering hde3 ... md: adding hde3 ... md: adding hdc3 ... md: adding hda3 ... md: created md0 md: bind<hda3> md: bind<hdc3> md: bind<hde3> md: running: <hde3><hdc3><hda3> raid5: device hde3 operational as raid disk 2 raid5: device hdc3 operational as raid disk 1 raid5: device hda3 operational as raid disk 0 raid5: allocated 3212kB for md0 raid5: raid level 5 set md0 active with 3 out of 3 devices, algorithm 0 RAID5 conf printout: --- rd:3 wd:3 fd:0 disk 0, o:1, dev:hda3 disk 1, o:1, dev:hdc3 disk 2, o:1, dev:hde3 md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 280k freed ----------- [cut here ] --------- [please bite here ] --------- Kernel BUG at drivers/ide/ide-io.c:63 invalid operand: 0000 [1] PREEMPT SMP CPU 0 Modules linked in: snd_usb_audio snd_usb_lib snd_rawmidi snd_hwdep Pid: 0, comm: swapper Not tainted 2.6.15-rc6top #1 RIP: 0010:[<ffffffff8038e995>] <ffffffff8038e995>{__ide_end_request+53} RSP: 0018:ffffffff806d67d0 EFLAGS: 00010046 RAX: 0000000001000479 RBX: ffff810002f7b490 RCX: 0000000000000008 RDX: 0000000000000000 RSI: ffff810002f7b490 RDI: ffffffff80730d98 RBP: 0000000000000000 R08: 000000003b9aca00 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000064 R12: ffffffff80730d98 R13: 0000000000000008 R14: 0000000000000001 R15: ffffffff80730c80 FS: 00002aaaab1aaae0(0000) GS:ffffffff80751800(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00002aaaaafbb7b0 CR3: 000000007e0e0000 CR4: 00000000000006e0 Process swapper (pid: 0, threadinfo ffffffff8075a000, task ffffffff805d36c0) Stack: ffff810002f7b490 ffff81013feeacd0 ffff810002f5a550 0000000000000050 0000000000000050 ffffffff80299aae 0000000000000246 ffff81013feeacd0 ffffffff80730d98 ffffffff8038f0f2 Call Trace: <IRQ> <ffffffff80299aae>{blk_pre_flush_end_io+110} <ffffffff8038f0f2>{ide_end_drive_cmd+946} <ffffffff8038f6f0>{drive_cmd_intr+288} <ffffffff8038f5d0>{drive_cmd_intr+0} <ffffffff80390850>{ide_intr+400} <ffffffff8015c7bc>{handle_IRQ_event+44} <ffffffff8015c8a1>{__do_IRQ+177} <ffffffff80110c9f>{do_IRQ+47} <ffffffff8010e2d8>{ret_from_intr+0} <ffffffff80390ad0>{ide_outb+0} <ffffffff80390ad6>{ide_outb+6} <ffffffff803995b1>{ide_do_rw_disk+529} <ffffffff8049a036>{ip_rcv+1302} <ffffffff80120000>{__ioremap+512} <ffffffff80390160>{ide_do_request+1648} <ffffffff8038f0f2>{ide_end_drive_cmd+946} <ffffffff80390895>{ide_intr+469} <ffffffff8015c7bc>{handle_IRQ_event+44} <ffffffff8015c8a1>{__do_IRQ+177} <ffffffff80110c9f>{do_IRQ+47} <ffffffff8010e2d8>{ret_from_intr+0} <EOI> <ffffffff8010ebf1>{kernel_thread+129} <ffffffff80390ad0>{ide_outb+0} <ffffffff8010bd96>{default_idle+54} <ffffffff8010c012>{cpu_idle+98} <ffffffff8075c835>{start_kernel+485} <ffffffff8075c294>{_sinittext+660} Code: 0f 0b 68 61 85 57 80 c2 3f 00 90 a8 02 74 0c 85 ed 7f 08 44 RIP <ffffffff8038e995>{__ide_end_request+53} RSP <ffffffff806d67d0> <0>Kernel panic - not syncing: Aiee, killing interrupt handler! NMI Watchdog detected LOCKUP on CPU 0 CPU 0 Modules linked in: snd_usb_audio snd_usb_lib snd_rawmidi snd_hwdep Pid: 0, comm: swapper Not tainted 2.6.15-rc6top #1 RIP: 0010:[<ffffffff801198f4>] <ffffffff801198f4>{__smp_call_function+116} RSP: 0018:ffffffff806d6488 EFLAGS: 00000097 RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000002 RDX: 0000ffff0000ffff RSI: 0000000000000000 RDI: ffffffff807560d8 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff80119a40 R13: 0000000000000000 R14: ffffffff805526dd R15: ffffffff80730c80 FS: 00002aaaab1aaae0(0000) GS:ffffffff80751800(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00002aaaaafbb7b0 CR3: 000000007e0e0000 CR4: 00000000000006e0 Process swapper (pid: 0, threadinfo ffffffff8075a000, task ffffffff805d36c0) Stack: ffffffff80119a40 0000000000000000 ffffffff00000000 ffffffff00000000 0000000000000400 0000000000000000 0000000000000000 ffffffff805d36c0 000000000000000b ffffffff80119aa0 Call Trace: <IRQ> <ffffffff80119a40>{smp_really_stop_cpu+0} <ffffffff80119aa0>{smp_send_stop+64} <ffffffff80135ca1>{panic+225} <ffffffff8010f543>{show_stack+211} <ffffffff8010f639>{show_registers+233} <ffffffff8013869f>{do_exit+143} <ffffffff80315327>{do_unblank_screen+119} <ffffffff8010f8f1>{die+81} <ffffffff8010fd41>{do_invalid_op+145} <ffffffff8038e995>{__ide_end_request+53} <ffffffff80136a1d>{printk+141} <ffffffff804d2b54>{ip_refrag+36} <ffffffff8010eaa1>{error_exit+0} <ffffffff8038e995>{__ide_end_request+53} <ffffffff80299aae>{blk_pre_flush_end_io+110} <ffffffff8038f0f2>{ide_end_drive_cmd+946} <ffffffff8038f6f0>{drive_cmd_intr+288} <ffffffff8038f5d0>{drive_cmd_intr+0} <ffffffff80390850>{ide_intr+400} <ffffffff8015c7bc>{handle_IRQ_event+44} <ffffffff8015c8a1>{__do_IRQ+177} <ffffffff80110c9f>{do_IRQ+47} <ffffffff8010e2d8>{ret_from_intr+0} <ffffffff80390ad0>{ide_outb+0} <ffffffff80390ad6>{ide_outb+6} <ffffffff803995b1>{ide_do_rw_disk+529} <ffffffff8049a036>{ip_rcv+1302} <ffffffff80120000>{__ioremap+512} <ffffffff80390160>{ide_do_request+1648} <ffffffff8038f0f2>{ide_end_drive_cmd+946} <ffffffff80390895>{ide_intr+469} <ffffffff8015c7bc>{handle_IRQ_event+44} <ffffffff8015c8a1>{__do_IRQ+177} <ffffffff80110c9f>{do_IRQ+47} <ffffffff8010e2d8>{ret_from_intr+0} <EOI> <ffffffff8010ebf1>{kernel_thread+129} <ffffffff80390ad0>{ide_outb+0} <ffffffff8010bd96>{default_idle+54} <ffffffff8010c012>{cpu_idle+98} <ffffffff8075c835>{start_kernel+485} <ffffffff8075c294>{_sinittext+660} Code: 39 d8 74 08 f3 90 eb f4 66 66 66 90 85 ed 74 0e 8b 44 24 14 console shuts up ... <0>Kernel panic - not syncing: Aiee, killing interrupt handler! NMI Watchdog detected LOCKUP on CPU 1 CPU 1 Modules linked in: snd_usb_audio snd_usb_lib snd_rawmidi snd_hwdep Pid: 0, comm: swapper Not tainted 2.6.15-rc6top #1 RIP: 0010:[<ffffffff80513975>] <ffffffff80513975>{_spin_lock_irqsave+117} RSP: 0018:ffff81013fc5fed8 EFLAGS: 00000002 RAX: 0000000000000000 RBX: ffffffff80755e40 RCX: 0000000000000001 RDX: ffff810002ca3e28 RSI: 0000000000000000 RDI: ffffffff80755e40 RBP: 0000000000000000 R08: ffff810002ca2000 R09: 0000000000000000 R10: 0000000000000002 R11: 0000000000005023 R12: ffff810002ca3e28 R13: 000000000000000f R14: 0000000000000000 R15: ffff810002ca3e28 FS: 00002aaaab0146d0(0000) GS:ffffffff80751880(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00000000004810b0 CR3: 000000013e467000 CR4: 00000000000006e0 Process swapper (pid: 0, threadinfo ffff810002ca2000, task ffff810002c9c080) Stack: 0000000000000046 ffff810002f67b40 ffff810002f6f400 ffffffff803906ef ffff81013fc5fef8 ffff81013fc5fef8 ffff810002f67b40 0000000000000000 ffff810002ca3e28 000000000000000f Call Trace: <IRQ> <ffffffff803906ef>{ide_intr+47} <ffffffff8015c7bc>{handle_IRQ_event+44} <ffffffff8015c8a1>{__do_IRQ+177} <ffffffff80110c9f>{do_IRQ+47} <ffffffff8010e2d8>{ret_from_intr+0} <EOI> <ffffffff8010bd96>{default_idle+54} <ffffffff8010c012>{cpu_idle+98} <ffffffff80767ff9>{start_secondary+1257} Code: f3 90 8b 03 85 c0 7e f1 65 48 8b 04 25 10 00 00 00 ff 80 44 console shuts up ... <0>Kernel panic - not syncing: Aiee, killing interrupt handler!
Attachment:
config.top.gz
Description: application/gunzip
- Follow-Ups:
- Re: 2.6.15rc6: ide oops+panic
- From: Andrew Morton <[email protected]>
- Re: 2.6.15rc6: ide oops+panic
- From: Bartlomiej Zolnierkiewicz <[email protected]>
- Re: 2.6.15rc6: ide oops+panic
- Prev by Date: Re: [patch 0/9] mutex subsystem, -V4
- Next by Date: Re: .config not updated after make clean
- Previous by thread: 4k stacks
- Next by thread: Re: 2.6.15rc6: ide oops+panic
- Index(es):
 |