From: Rajesh Shah <[email protected]>
Per the PCI Express spec, the power-fault-detected bit in the
slot status register can be set anytime hardware detects a power
fault, regardless of whether the slot has a device populated in
it or not. This bit is sticky and must be explicitly cleared.
This patch is needed to allow hot-add after such a power fault
has been detected.
Signed-off-by: Rajesh Shah <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/pci/hotplug/pciehp.h | 1 -
drivers/pci/hotplug/pciehp_ctrl.c | 15 ++-------------
drivers/pci/hotplug/pciehp_hpc.c | 10 +++++++++-
3 files changed, 11 insertions(+), 15 deletions(-)
--- usb-2.6.orig/drivers/pci/hotplug/pciehp.h
+++ usb-2.6/drivers/pci/hotplug/pciehp.h
@@ -59,7 +59,6 @@ struct slot {
struct slot *next;
u8 bus;
u8 device;
- u16 status;
u32 number;
u8 state;
struct timer_list task_event;
--- usb-2.6.orig/drivers/pci/hotplug/pciehp_ctrl.c
+++ usb-2.6/drivers/pci/hotplug/pciehp_ctrl.c
@@ -207,7 +207,6 @@ u8 pciehp_handle_power_fault(u8 hp_slot,
* power fault Cleared
*/
info("Power fault cleared on Slot(%d)\n", ctrl->first_slot + hp_slot);
- p_slot->status = 0x00;
taskInfo->event_type = INT_POWER_FAULT_CLEAR;
} else {
/*
@@ -215,8 +214,6 @@ u8 pciehp_handle_power_fault(u8 hp_slot,
*/
info("Power fault on Slot(%d)\n", ctrl->first_slot + hp_slot);
taskInfo->event_type = INT_POWER_FAULT;
- /* set power fault status for this board */
- p_slot->status = 0xFF;
info("power fault bit %x set\n", hp_slot);
}
if (rc)
@@ -317,13 +314,10 @@ static int board_added(struct slot *p_sl
return rc;
}
- dbg("%s: slot status = %x\n", __FUNCTION__, p_slot->status);
-
/* Check for a power fault */
- if (p_slot->status == 0xFF) {
- /* power fault occurred, but it was benign */
+ if (p_slot->hpc_ops->query_power_fault(p_slot)) {
+ dbg("%s: power fault detected\n", __FUNCTION__);
rc = POWER_FAILURE;
- p_slot->status = 0;
goto err_exit;
}
@@ -334,8 +328,6 @@ static int board_added(struct slot *p_sl
goto err_exit;
}
- p_slot->status = 0;
-
/*
* Some PCI Express root ports require fixup after hot-plug operation.
*/
@@ -382,9 +374,6 @@ static int remove_board(struct slot *p_s
dbg("In %s, hp_slot = %d\n", __FUNCTION__, hp_slot);
- /* Change status to shutdown */
- p_slot->status = 0x01;
-
/* Wait for exclusive access to hardware */
down(&ctrl->crit_sect);
--- usb-2.6.orig/drivers/pci/hotplug/pciehp_hpc.c
+++ usb-2.6/drivers/pci/hotplug/pciehp_hpc.c
@@ -750,7 +750,7 @@ static int hpc_power_on_slot(struct slot
{
struct php_ctlr_state_s *php_ctlr = slot->ctrl->hpc_ctlr_handle;
u16 slot_cmd;
- u16 slot_ctrl;
+ u16 slot_ctrl, slot_status;
int retval = 0;
@@ -767,6 +767,14 @@ static int hpc_power_on_slot(struct slot
return -1;
}
+ /* Clear sticky power-fault bit from previous power failures */
+ hp_register_read_word(php_ctlr->pci_dev,
+ SLOT_STATUS(slot->ctrl->cap_base), slot_status);
+ slot_status &= PWR_FAULT_DETECTED;
+ if (slot_status)
+ hp_register_write_word(php_ctlr->pci_dev,
+ SLOT_STATUS(slot->ctrl->cap_base), slot_status);
+
retval = hp_register_read_word(php_ctlr->pci_dev, SLOT_CTRL(slot->ctrl->cap_base), slot_ctrl);
if (retval) {
--
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
