[RFC: 2.6 patch] remove drivers/net/tulip/xircom_tulip_cb.c

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This patch removes the obsolete drivers/net/tulip/xircom_tulip_cb.c 
driver.

Is there any reason why it should be kept?


Signed-off-by: Adrian Bunk <[email protected]>

---

 drivers/net/tulip/Kconfig           |   16 
 drivers/net/tulip/Makefile          |    1 
 drivers/net/tulip/xircom_tulip_cb.c | 1748 ----------------------------
 3 files changed, 1 insertion(+), 1764 deletions(-)

--- linux-2.6.15-rc1-mm1-full/drivers/net/tulip/Kconfig.old	2005-11-18 03:45:53.000000000 +0100
+++ linux-2.6.15-rc1-mm1-full/drivers/net/tulip/Kconfig	2005-11-18 03:46:20.000000000 +0100
@@ -148,7 +148,7 @@
 	  be called uli526x.
 	  
 config PCMCIA_XIRCOM
-	tristate "Xircom CardBus support (new driver)"
+	tristate "Xircom CardBus support"
 	depends on NET_TULIP && CARDBUS
 	---help---
 	  This driver is for the Digital "Tulip" Ethernet CardBus adapters.
@@ -160,19 +160,5 @@
 	  <file:Documentation/networking/net-modules.txt>.  The module will
 	  be called xircom_cb.  If unsure, say N.
 
-config PCMCIA_XIRTULIP
-	tristate "Xircom Tulip-like CardBus support (old driver)"
-	depends on NET_TULIP && CARDBUS && BROKEN_ON_SMP
-	select CRC32
-	---help---
-	  This driver is for the Digital "Tulip" Ethernet CardBus adapters.
-	  It should work with most DEC 21*4*-based chips/ethercards, as well
-	  as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
-	  ASIX.
-
-	  To compile this driver as a module, choose M here and read
-	  <file:Documentation/networking/net-modules.txt>.  The module will
-	  be called xircom_tulip_cb.  If unsure, say N.
-
 endmenu
 
--- linux-2.6.15-rc1-mm1-full/drivers/net/tulip/Makefile.old	2005-11-18 03:46:32.000000000 +0100
+++ linux-2.6.15-rc1-mm1-full/drivers/net/tulip/Makefile	2005-11-18 03:46:41.000000000 +0100
@@ -2,7 +2,6 @@
 # Makefile for the Linux "Tulip" family network device drivers.
 #
 
-obj-$(CONFIG_PCMCIA_XIRTULIP)	+= xircom_tulip_cb.o
 obj-$(CONFIG_PCMCIA_XIRCOM)	+= xircom_cb.o
 obj-$(CONFIG_DM9102)		+= dmfe.o
 obj-$(CONFIG_WINBOND_840)	+= winbond-840.o
--- linux-2.6.15-rc1-mm1-full/drivers/net/tulip/xircom_tulip_cb.c	2005-10-28 02:02:08.000000000 +0200
+++ /dev/null	2005-11-08 19:07:57.000000000 +0100
@@ -1,1748 +0,0 @@
-/* xircom_tulip_cb.c: A Xircom CBE-100 ethernet driver for Linux. */
-/*
-	Written/copyright 1994-1999 by Donald Becker.
-
-	This software may be used and distributed according to the terms
-	of the GNU General Public License, incorporated herein by reference.
-
-	The author may be reached as [email protected], or C/O
-	Scyld Computing Corporation
-	410 Severn Ave., Suite 210
-	Annapolis MD 21403
-
-	-----------------------------------------------------------
-
-	Linux kernel-specific changes:
-
-	LK1.0 (Ion Badulescu)
-	- Major cleanup
-	- Use 2.4 PCI API
-	- Support ethtool
-	- Rewrite perfect filter/hash code
-	- Use interrupts for media changes
-
-	LK1.1 (Ion Badulescu)
-	- Disallow negotiation of unsupported full-duplex modes
-*/
-
-#define DRV_NAME	"xircom_tulip_cb"
-#define DRV_VERSION	"0.91+LK1.1"
-#define DRV_RELDATE	"October 11, 2001"
-
-#define CARDBUS 1
-
-/* A few user-configurable values. */
-
-#define xircom_debug debug
-#ifdef XIRCOM_DEBUG
-static int xircom_debug = XIRCOM_DEBUG;
-#else
-static int xircom_debug = 1;
-#endif
-
-/* Maximum events (Rx packets, etc.) to handle at each interrupt. */
-static int max_interrupt_work = 25;
-
-#define MAX_UNITS 4
-/* Used to pass the full-duplex flag, etc. */
-static int full_duplex[MAX_UNITS];
-static int options[MAX_UNITS];
-static int mtu[MAX_UNITS];			/* Jumbo MTU for interfaces. */
-
-/* Keep the ring sizes a power of two for efficiency.
-   Making the Tx ring too large decreases the effectiveness of channel
-   bonding and packet priority.
-   There are no ill effects from too-large receive rings. */
-#define TX_RING_SIZE	16
-#define RX_RING_SIZE	32
-
-/* Set the copy breakpoint for the copy-only-tiny-buffer Rx structure. */
-#ifdef __alpha__
-static int rx_copybreak = 1518;
-#else
-static int rx_copybreak = 100;
-#endif
-
-/*
-  Set the bus performance register.
-	Typical: Set 16 longword cache alignment, no burst limit.
-	Cache alignment bits 15:14	     Burst length 13:8
-		0000	No alignment  0x00000000 unlimited		0800 8 longwords
-		4000	8  longwords		0100 1 longword		1000 16 longwords
-		8000	16 longwords		0200 2 longwords	2000 32 longwords
-		C000	32  longwords		0400 4 longwords
-	Warning: many older 486 systems are broken and require setting 0x00A04800
-	   8 longword cache alignment, 8 longword burst.
-	ToDo: Non-Intel setting could be better.
-*/
-
-#if defined(__alpha__) || defined(__ia64__) || defined(__x86_64__)
-static int csr0 = 0x01A00000 | 0xE000;
-#elif defined(__powerpc__)
-static int csr0 = 0x01B00000 | 0x8000;
-#elif defined(__sparc__)
-static int csr0 = 0x01B00080 | 0x8000;
-#elif defined(__i386__)
-static int csr0 = 0x01A00000 | 0x8000;
-#else
-#warning Processor architecture undefined!
-static int csr0 = 0x00A00000 | 0x4800;
-#endif
-
-/* Operational parameters that usually are not changed. */
-/* Time in jiffies before concluding the transmitter is hung. */
-#define TX_TIMEOUT		(4 * HZ)
-#define PKT_BUF_SZ		1536			/* Size of each temporary Rx buffer.*/
-#define PKT_SETUP_SZ		192			/* Size of the setup frame */
-
-/* PCI registers */
-#define PCI_POWERMGMT 	0x40
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
-#include <linux/crc32.h>
-
-#include <asm/io.h>
-#include <asm/processor.h>	/* Processor type for cache alignment. */
-#include <asm/uaccess.h>
-
-
-/* These identify the driver base version and may not be removed. */
-static char version[] __devinitdata =
-KERN_INFO DRV_NAME ".c derived from tulip.c:v0.91 4/14/99 [email protected]\n"
-KERN_INFO " unofficial 2.4.x kernel port, version " DRV_VERSION ", " DRV_RELDATE "\n";
-
-MODULE_AUTHOR("Donald Becker <[email protected]>");
-MODULE_DESCRIPTION("Xircom CBE-100 ethernet driver");
-MODULE_LICENSE("GPL v2");
-MODULE_VERSION(DRV_VERSION);
-
-module_param(debug, int, 0);
-module_param(max_interrupt_work, int, 0);
-module_param(rx_copybreak, int, 0);
-module_param(csr0, int, 0);
-
-module_param_array(options, int, NULL, 0);
-module_param_array(full_duplex, int, NULL, 0);
-
-#define RUN_AT(x) (jiffies + (x))
-
-/*
-				Theory of Operation
-
-I. Board Compatibility
-
-This device driver was forked from the driver for the DECchip "Tulip",
-Digital's single-chip ethernet controllers for PCI.  It supports Xircom's
-almost-Tulip-compatible CBE-100 CardBus adapters.
-
-II. Board-specific settings
-
-PCI bus devices are configured by the system at boot time, so no jumpers
-need to be set on the board.  The system BIOS preferably should assign the
-PCI INTA signal to an otherwise unused system IRQ line.
-
-III. Driver operation
-
-IIIa. Ring buffers
-
-The Xircom can use either ring buffers or lists of Tx and Rx descriptors.
-This driver uses statically allocated rings of Rx and Tx descriptors, set at
-compile time by RX/TX_RING_SIZE.  This version of the driver allocates skbuffs
-for the Rx ring buffers at open() time and passes the skb->data field to the
-Xircom as receive data buffers.  When an incoming frame is less than
-RX_COPYBREAK bytes long, a fresh skbuff is allocated and the frame is
-copied to the new skbuff.  When the incoming frame is larger, the skbuff is
-passed directly up the protocol stack and replaced by a newly allocated
-skbuff.
-
-The RX_COPYBREAK value is chosen to trade-off the memory wasted by
-using a full-sized skbuff for small frames vs. the copying costs of larger
-frames.  For small frames the copying cost is negligible (esp. considering
-that we are pre-loading the cache with immediately useful header
-information).  For large frames the copying cost is non-trivial, and the
-larger copy might flush the cache of useful data.  A subtle aspect of this
-choice is that the Xircom only receives into longword aligned buffers, thus
-the IP header at offset 14 isn't longword aligned for further processing.
-Copied frames are put into the new skbuff at an offset of "+2", thus copying
-has the beneficial effect of aligning the IP header and preloading the
-cache.
-
-IIIC. Synchronization
-The driver runs as two independent, single-threaded flows of control.  One
-is the send-packet routine, which enforces single-threaded use by the
-dev->tbusy flag.  The other thread is the interrupt handler, which is single
-threaded by the hardware and other software.
-
-The send packet thread has partial control over the Tx ring and 'dev->tbusy'
-flag.  It sets the tbusy flag whenever it's queuing a Tx packet. If the next
-queue slot is empty, it clears the tbusy flag when finished otherwise it sets
-the 'tp->tx_full' flag.
-
-The interrupt handler has exclusive control over the Rx ring and records stats
-from the Tx ring.  (The Tx-done interrupt can't be selectively turned off, so
-we can't avoid the interrupt overhead by having the Tx routine reap the Tx
-stats.)	 After reaping the stats, it marks the queue entry as empty by setting
-the 'base' to zero.	 Iff the 'tp->tx_full' flag is set, it clears both the
-tx_full and tbusy flags.
-
-IV. Notes
-
-IVb. References
-
-http://cesdis.gsfc.nasa.gov/linux/misc/NWay.html
-http://www.digital.com  (search for current 21*4* datasheets and "21X4 SROM")
-http://www.national.com/pf/DP/DP83840A.html
-
-IVc. Errata
-
-*/
-
-/* A full-duplex map for media types. */
-enum MediaIs {
-	MediaIsFD = 1, MediaAlwaysFD=2, MediaIsMII=4, MediaIsFx=8,
-	MediaIs100=16};
-static const char media_cap[] =
-{0,0,0,16,  3,19,16,24,  27,4,7,5, 0,20,23,20 };
-
-/* Offsets to the Command and Status Registers, "CSRs".  All accesses
-   must be longword instructions and quadword aligned. */
-enum xircom_offsets {
-	CSR0=0,    CSR1=0x08, CSR2=0x10, CSR3=0x18, CSR4=0x20, CSR5=0x28,
-	CSR6=0x30, CSR7=0x38, CSR8=0x40, CSR9=0x48, CSR10=0x50, CSR11=0x58,
-	CSR12=0x60, CSR13=0x68, CSR14=0x70, CSR15=0x78, CSR16=0x04, };
-
-/* The bits in the CSR5 status registers, mostly interrupt sources. */
-enum status_bits {
-	LinkChange=0x08000000,
-	NormalIntr=0x10000, NormalIntrMask=0x00014045,
-	AbnormalIntr=0x8000, AbnormalIntrMask=0x0a00a5a2,
-	ReservedIntrMask=0xe0001a18,
-	EarlyRxIntr=0x4000, BusErrorIntr=0x2000,
-	EarlyTxIntr=0x400, RxDied=0x100, RxNoBuf=0x80, RxIntr=0x40,
-	TxFIFOUnderflow=0x20, TxNoBuf=0x04, TxDied=0x02, TxIntr=0x01,
-};
-
-enum csr0_control_bits {
-	EnableMWI=0x01000000, EnableMRL=0x00800000,
-	EnableMRM=0x00200000, EqualBusPrio=0x02,
-	SoftwareReset=0x01,
-};
-
-enum csr6_control_bits {
-	ReceiveAllBit=0x40000000, AllMultiBit=0x80, PromiscBit=0x40,
-	HashFilterBit=0x01, FullDuplexBit=0x0200,
-	TxThresh10=0x400000, TxStoreForw=0x200000,
-	TxThreshMask=0xc000, TxThreshShift=14,
-	EnableTx=0x2000, EnableRx=0x02,
-	ReservedZeroMask=0x8d930134, ReservedOneMask=0x320c0000,
-	EnableTxRx=(EnableTx | EnableRx),
-};
-
-
-enum tbl_flag {
-	HAS_MII=1, HAS_ACPI=2,
-};
-static struct xircom_chip_table {
-	char *chip_name;
-	int valid_intrs;			/* CSR7 interrupt enable settings */
-	int flags;
-} xircom_tbl[] = {
-  { "Xircom Cardbus Adapter",
-	LinkChange | NormalIntr | AbnormalIntr | BusErrorIntr |
-	RxDied | RxNoBuf | RxIntr | TxFIFOUnderflow | TxNoBuf | TxDied | TxIntr,
-	HAS_MII | HAS_ACPI, },
-  { NULL, },
-};
-/* This matches the table above. */
-enum chips {
-	X3201_3,
-};
-
-
-/* The Xircom Rx and Tx buffer descriptors. */
-struct xircom_rx_desc {
-	s32 status;
-	s32 length;
-	u32 buffer1, buffer2;
-};
-
-struct xircom_tx_desc {
-	s32 status;
-	s32 length;
-	u32 buffer1, buffer2;				/* We use only buffer 1.  */
-};
-
-enum tx_desc0_status_bits {
-	Tx0DescOwned=0x80000000, Tx0DescError=0x8000, Tx0NoCarrier=0x0800,
-	Tx0LateColl=0x0200, Tx0ManyColl=0x0100, Tx0Underflow=0x02,
-};
-enum tx_desc1_status_bits {
-	Tx1ComplIntr=0x80000000, Tx1LastSeg=0x40000000, Tx1FirstSeg=0x20000000,
-	Tx1SetupPkt=0x08000000, Tx1DisableCRC=0x04000000, Tx1RingWrap=0x02000000,
-	Tx1ChainDesc=0x01000000, Tx1NoPad=0x800000, Tx1HashSetup=0x400000,
-	Tx1WholePkt=(Tx1FirstSeg | Tx1LastSeg),
-};
-enum rx_desc0_status_bits {
-	Rx0DescOwned=0x80000000, Rx0DescError=0x8000, Rx0NoSpace=0x4000,
-	Rx0Runt=0x0800, Rx0McastPkt=0x0400, Rx0FirstSeg=0x0200, Rx0LastSeg=0x0100,
-	Rx0HugeFrame=0x80, Rx0CRCError=0x02,
-	Rx0WholePkt=(Rx0FirstSeg | Rx0LastSeg),
-};
-enum rx_desc1_status_bits {
-	Rx1RingWrap=0x02000000, Rx1ChainDesc=0x01000000,
-};
-
-struct xircom_private {
-	struct xircom_rx_desc rx_ring[RX_RING_SIZE];
-	struct xircom_tx_desc tx_ring[TX_RING_SIZE];
-	/* The saved address of a sent-in-place packet/buffer, for skfree(). */
-	struct sk_buff* tx_skbuff[TX_RING_SIZE];
-#ifdef CARDBUS
-	/* The X3201-3 requires 4-byte aligned tx bufs */
-	struct sk_buff* tx_aligned_skbuff[TX_RING_SIZE];
-#endif
-	/* The addresses of receive-in-place skbuffs. */
-	struct sk_buff* rx_skbuff[RX_RING_SIZE];
-	u16 setup_frame[PKT_SETUP_SZ / sizeof(u16)];	/* Pseudo-Tx frame to init address table. */
-	int chip_id;
-	struct net_device_stats stats;
-	unsigned int cur_rx, cur_tx;		/* The next free ring entry */
-	unsigned int dirty_rx, dirty_tx;	/* The ring entries to be free()ed. */
-	unsigned int tx_full:1;				/* The Tx queue is full. */
-	unsigned int speed100:1;
-	unsigned int full_duplex:1;			/* Full-duplex operation requested. */
-	unsigned int autoneg:1;
-	unsigned int default_port:4;		/* Last dev->if_port value. */
-	unsigned int open:1;
-	unsigned int csr0;					/* CSR0 setting. */
-	unsigned int csr6;					/* Current CSR6 control settings. */
-	u16 to_advertise;					/* NWay capabilities advertised.  */
-	u16 advertising[4];
-	signed char phys[4], mii_cnt;		/* MII device addresses. */
-	int saved_if_port;
-	struct pci_dev *pdev;
-	spinlock_t lock;
-};
-
-static int mdio_read(struct net_device *dev, int phy_id, int location);
-static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
-static void xircom_up(struct net_device *dev);
-static void xircom_down(struct net_device *dev);
-static int xircom_open(struct net_device *dev);
-static void xircom_tx_timeout(struct net_device *dev);
-static void xircom_init_ring(struct net_device *dev);
-static int xircom_start_xmit(struct sk_buff *skb, struct net_device *dev);
-static int xircom_rx(struct net_device *dev);
-static void xircom_media_change(struct net_device *dev);
-static irqreturn_t xircom_interrupt(int irq, void *dev_instance, struct pt_regs *regs);
-static int xircom_close(struct net_device *dev);
-static struct net_device_stats *xircom_get_stats(struct net_device *dev);
-static int xircom_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-static void set_rx_mode(struct net_device *dev);
-static void check_duplex(struct net_device *dev);
-static struct ethtool_ops ops;
-
-
-/* The Xircom cards are picky about when certain bits in CSR6 can be
-   manipulated.  Keith Owens <[email protected]>. */
-static void outl_CSR6(u32 newcsr6, long ioaddr)
-{
-	const int strict_bits =
-		TxThresh10 | TxStoreForw | TxThreshMask | EnableTxRx | FullDuplexBit;
-    int csr5, csr5_22_20, csr5_19_17, currcsr6, attempts = 200;
-    unsigned long flags;
-    save_flags(flags);
-    cli();
-	/* mask out the reserved bits that always read 0 on the Xircom cards */
-	newcsr6 &= ~ReservedZeroMask;
-	/* or in the reserved bits that always read 1 */
-	newcsr6 |= ReservedOneMask;
-    currcsr6 = inl(ioaddr + CSR6);
-    if (((newcsr6 & strict_bits) == (currcsr6 & strict_bits)) ||
-	((currcsr6 & ~EnableTxRx) == 0)) {
-		outl(newcsr6, ioaddr + CSR6);	/* safe */
-		restore_flags(flags);
-		return;
-    }
-    /* make sure the transmitter and receiver are stopped first */
-    currcsr6 &= ~EnableTxRx;
-    while (1) {
-		csr5 = inl(ioaddr + CSR5);
-		if (csr5 == 0xffffffff)
-			break;  /* cannot read csr5, card removed? */
-		csr5_22_20 = csr5 & 0x700000;
-		csr5_19_17 = csr5 & 0x0e0000;
-		if ((csr5_22_20 == 0 || csr5_22_20 == 0x600000) &&
-			(csr5_19_17 == 0 || csr5_19_17 == 0x80000 || csr5_19_17 == 0xc0000))
-			break;  /* both are stopped or suspended */
-		if (!--attempts) {
-			printk(KERN_INFO DRV_NAME ": outl_CSR6 too many attempts,"
-				   "csr5=0x%08x\n", csr5);
-			outl(newcsr6, ioaddr + CSR6);  /* unsafe but do it anyway */
-			restore_flags(flags);
-			return;
-		}
-		outl(currcsr6, ioaddr + CSR6);
-		udelay(1);
-    }
-    /* now it is safe to change csr6 */
-    outl(newcsr6, ioaddr + CSR6);
-    restore_flags(flags);
-}
-
-
-static void __devinit read_mac_address(struct net_device *dev)
-{
-	long ioaddr = dev->base_addr;
-	int i, j;
-	unsigned char tuple, link, data_id, data_count;
-
-	/* Xircom has its address stored in the CIS;
-	 * we access it through the boot rom interface for now
-	 * this might not work, as the CIS is not parsed but I
-	 * (danilo) use the offset I found on my card's CIS !!!
-	 *
-	 * Doug Ledford: I changed this routine around so that it
-	 * walks the CIS memory space, parsing the config items, and
-	 * finds the proper lan_node_id tuple and uses the data
-	 * stored there.
-	 */
-	outl(1 << 12, ioaddr + CSR9); /* enable boot rom access */
-	for (i = 0x100; i < 0x1f7; i += link+2) {
-		outl(i, ioaddr + CSR10);
-		tuple = inl(ioaddr + CSR9) & 0xff;
-		outl(i + 1, ioaddr + CSR10);
-		link = inl(ioaddr + CSR9) & 0xff;
-		outl(i + 2, ioaddr + CSR10);
-		data_id = inl(ioaddr + CSR9) & 0xff;
-		outl(i + 3, ioaddr + CSR10);
-		data_count = inl(ioaddr + CSR9) & 0xff;
-		if ( (tuple == 0x22) &&
-			 (data_id == 0x04) && (data_count == 0x06) ) {
-			/*
-			 * This is it.  We have the data we want.
-			 */
-			for (j = 0; j < 6; j++) {
-				outl(i + j + 4, ioaddr + CSR10);
-				dev->dev_addr[j] = inl(ioaddr + CSR9) & 0xff;
-			}
-			break;
-		} else if (link == 0) {
-			break;
-		}
-	}
-}
-
-
-/*
- * locate the MII interfaces and initialize them.
- * we disable full-duplex modes here,
- * because we don't know how to handle them.
- */
-static void find_mii_transceivers(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	int phy, phy_idx;
-
-	if (media_cap[tp->default_port] & MediaIsMII) {
-		u16 media2advert[] = { 0x20, 0x40, 0x03e0, 0x60, 0x80, 0x100, 0x200 };
-		tp->to_advertise = media2advert[tp->default_port - 9];
-	} else
-		tp->to_advertise =
-			/*ADVERTISE_100BASE4 | ADVERTISE_100FULL |*/ ADVERTISE_100HALF |
-			/*ADVERTISE_10FULL |*/ ADVERTISE_10HALF | ADVERTISE_CSMA;
-
-	/* Find the connected MII xcvrs.
-	   Doing this in open() would allow detecting external xcvrs later,
-	   but takes much time. */
-	for (phy = 0, phy_idx = 0; phy < 32 && phy_idx < sizeof(tp->phys); phy++) {
-		int mii_status = mdio_read(dev, phy, MII_BMSR);
-		if ((mii_status & (BMSR_100BASE4 | BMSR_100HALF | BMSR_10HALF)) == BMSR_100BASE4 ||
-			((mii_status & BMSR_100BASE4) == 0 &&
-			 (mii_status & (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL | BMSR_10HALF)) != 0)) {
-			int mii_reg0 = mdio_read(dev, phy, MII_BMCR);
-			int mii_advert = mdio_read(dev, phy, MII_ADVERTISE);
-			int reg4 = ((mii_status >> 6) & tp->to_advertise) | ADVERTISE_CSMA;
-			tp->phys[phy_idx] = phy;
-			tp->advertising[phy_idx++] = reg4;
-			printk(KERN_INFO "%s:  MII transceiver #%d "
-				   "config %4.4x status %4.4x advertising %4.4x.\n",
-				   dev->name, phy, mii_reg0, mii_status, mii_advert);
-		}
-	}
-	tp->mii_cnt = phy_idx;
-	if (phy_idx == 0) {
-		printk(KERN_INFO "%s: ***WARNING***: No MII transceiver found!\n",
-			   dev->name);
-		tp->phys[0] = 0;
-	}
-}
-
-
-/*
- * To quote Arjan van de Ven:
- *   transceiver_voodoo() enables the external UTP plug thingy.
- *   it's called voodoo as I stole this code and cannot cross-reference
- *   it with the specification.
- * Actually it seems to go like this:
- * - GPIO2 enables the MII itself so we can talk to it. The MII gets reset
- *   so any prior MII settings are lost.
- * - GPIO0 enables the TP port so the MII can talk to the network.
- * - a software reset will reset both GPIO pins.
- * I also moved the software reset here, because doing it in xircom_up()
- * required enabling the GPIO pins each time, which reset the MII each time.
- * Thus we couldn't control the MII -- which sucks because we don't know
- * how to handle full-duplex modes so we *must* disable them.
- */
-static void transceiver_voodoo(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	long ioaddr = dev->base_addr;
-
-	/* Reset the chip, holding bit 0 set at least 50 PCI cycles. */
-	outl(SoftwareReset, ioaddr + CSR0);
-	udelay(2);
-
-	/* Deassert reset. */
-	outl(tp->csr0, ioaddr + CSR0);
-
-	/* Reset the xcvr interface and turn on heartbeat. */
-	outl(0x0008, ioaddr + CSR15);
-	udelay(5);  /* The delays are Xircom-recommended to give the
-				 * chipset time to reset the actual hardware
-				 * on the PCMCIA card
-				 */
-	outl(0xa8050000, ioaddr + CSR15);
-	udelay(5);
-	outl(0xa00f0000, ioaddr + CSR15);
-	udelay(5);
-
-	outl_CSR6(0, ioaddr);
-	//outl_CSR6(FullDuplexBit, ioaddr);
-}
-
-
-static int __devinit xircom_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
-{
-	struct net_device *dev;
-	struct xircom_private *tp;
-	static int board_idx = -1;
-	int chip_idx = id->driver_data;
-	long ioaddr;
-	int i;
-	u8 chip_rev;
-
-/* when built into the kernel, we only print version if device is found */
-#ifndef MODULE
-	static int printed_version;
-	if (!printed_version++)
-		printk(version);
-#endif
-
-	//printk(KERN_INFO "xircom_init_one(%s)\n", pci_name(pdev));
-
-	board_idx++;
-
-	if (pci_enable_device(pdev))
-		return -ENODEV;
-
-	pci_set_master(pdev);
-
-	ioaddr = pci_resource_start(pdev, 0);
-	dev = alloc_etherdev(sizeof(*tp));
-	if (!dev) {
-		printk (KERN_ERR DRV_NAME "%d: cannot alloc etherdev, aborting\n", board_idx);
-		return -ENOMEM;
-	}
-	SET_MODULE_OWNER(dev);
-	SET_NETDEV_DEV(dev, &pdev->dev);
-
-	dev->base_addr = ioaddr;
-	dev->irq = pdev->irq;
-
-	if (pci_request_regions(pdev, dev->name)) {
-		printk (KERN_ERR DRV_NAME " %d: cannot reserve PCI resources, aborting\n", board_idx);
-		goto err_out_free_netdev;
-	}
-
-	/* Bring the chip out of sleep mode.
-	   Caution: Snooze mode does not work with some boards! */
-	if (xircom_tbl[chip_idx].flags & HAS_ACPI)
-		pci_write_config_dword(pdev, PCI_POWERMGMT, 0);
-
-	/* Stop the chip's Tx and Rx processes. */
-	outl_CSR6(inl(ioaddr + CSR6) & ~EnableTxRx, ioaddr);
-	/* Clear the missed-packet counter. */
-	(volatile int)inl(ioaddr + CSR8);
-
-	tp = netdev_priv(dev);
-
-	spin_lock_init(&tp->lock);
-	tp->pdev = pdev;
-	tp->chip_id = chip_idx;
-	/* BugFixes: The 21143-TD hangs with PCI Write-and-Invalidate cycles. */
-	/* XXX: is this necessary for Xircom? */
-	tp->csr0 = csr0 & ~EnableMWI;
-
-	pci_set_drvdata(pdev, dev);
-
-	/* The lower four bits are the media type. */
-	if (board_idx >= 0 && board_idx < MAX_UNITS) {
-		tp->default_port = options[board_idx] & 15;
-		if ((options[board_idx] & 0x90) || full_duplex[board_idx] > 0)
-			tp->full_duplex = 1;
-		if (mtu[board_idx] > 0)
-			dev->mtu = mtu[board_idx];
-	}
-	if (dev->mem_start)
-		tp->default_port = dev->mem_start;
-	if (tp->default_port) {
-		if (media_cap[tp->default_port] & MediaAlwaysFD)
-			tp->full_duplex = 1;
-	}
-	if (tp->full_duplex)
-		tp->autoneg = 0;
-	else
-		tp->autoneg = 1;
-	tp->speed100 = 1;
-
-	/* The Xircom-specific entries in the device structure. */
-	dev->open = &xircom_open;
-	dev->hard_start_xmit = &xircom_start_xmit;
-	dev->stop = &xircom_close;
-	dev->get_stats = &xircom_get_stats;
-	dev->do_ioctl = &xircom_ioctl;
-#ifdef HAVE_MULTICAST
-	dev->set_multicast_list = &set_rx_mode;
-#endif
-	dev->tx_timeout = xircom_tx_timeout;
-	dev->watchdog_timeo = TX_TIMEOUT;
-	SET_ETHTOOL_OPS(dev, &ops);
-
-	transceiver_voodoo(dev);
-
-	read_mac_address(dev);
-
-	if (register_netdev(dev))
-		goto err_out_cleardev;
-
-	pci_read_config_byte(pdev, PCI_REVISION_ID, &chip_rev);
-	printk(KERN_INFO "%s: %s rev %d at %#3lx,",
-	       dev->name, xircom_tbl[chip_idx].chip_name, chip_rev, ioaddr);
-	for (i = 0; i < 6; i++)
-		printk("%c%2.2X", i ? ':' : ' ', dev->dev_addr[i]);
-	printk(", IRQ %d.\n", dev->irq);
-
-	if (xircom_tbl[chip_idx].flags & HAS_MII) {
-		find_mii_transceivers(dev);
-		check_duplex(dev);
-	}
-
-	return 0;
-
-err_out_cleardev:
-	pci_set_drvdata(pdev, NULL);
-	pci_release_regions(pdev);
-err_out_free_netdev:
-	free_netdev(dev);
-	return -ENODEV;
-}
-
-
-/* MII transceiver control section.
-   Read and write the MII registers using software-generated serial
-   MDIO protocol.  See the MII specifications or DP83840A data sheet
-   for details. */
-
-/* The maximum data clock rate is 2.5 Mhz.  The minimum timing is usually
-   met by back-to-back PCI I/O cycles, but we insert a delay to avoid
-   "overclocking" issues or future 66Mhz PCI. */
-#define mdio_delay() inl(mdio_addr)
-
-/* Read and write the MII registers using software-generated serial
-   MDIO protocol.  It is just different enough from the EEPROM protocol
-   to not share code.  The maxium data clock rate is 2.5 Mhz. */
-#define MDIO_SHIFT_CLK	0x10000
-#define MDIO_DATA_WRITE0 0x00000
-#define MDIO_DATA_WRITE1 0x20000
-#define MDIO_ENB		0x00000		/* Ignore the 0x02000 databook setting. */
-#define MDIO_ENB_IN		0x40000
-#define MDIO_DATA_READ	0x80000
-
-static int mdio_read(struct net_device *dev, int phy_id, int location)
-{
-	int i;
-	int read_cmd = (0xf6 << 10) | (phy_id << 5) | location;
-	int retval = 0;
-	long ioaddr = dev->base_addr;
-	long mdio_addr = ioaddr + CSR9;
-
-	/* Establish sync by sending at least 32 logic ones. */
-	for (i = 32; i >= 0; i--) {
-		outl(MDIO_ENB | MDIO_DATA_WRITE1, mdio_addr);
-		mdio_delay();
-		outl(MDIO_ENB | MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
-		mdio_delay();
-	}
-	/* Shift the read command bits out. */
-	for (i = 15; i >= 0; i--) {
-		int dataval = (read_cmd & (1 << i)) ? MDIO_DATA_WRITE1 : 0;
-
-		outl(MDIO_ENB | dataval, mdio_addr);
-		mdio_delay();
-		outl(MDIO_ENB | dataval | MDIO_SHIFT_CLK, mdio_addr);
-		mdio_delay();
-	}
-	/* Read the two transition, 16 data, and wire-idle bits. */
-	for (i = 19; i > 0; i--) {
-		outl(MDIO_ENB_IN, mdio_addr);
-		mdio_delay();
-		retval = (retval << 1) | ((inl(mdio_addr) & MDIO_DATA_READ) ? 1 : 0);
-		outl(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
-		mdio_delay();
-	}
-	return (retval>>1) & 0xffff;
-}
-
-
-static void mdio_write(struct net_device *dev, int phy_id, int location, int value)
-{
-	int i;
-	int cmd = (0x5002 << 16) | (phy_id << 23) | (location << 18) | value;
-	long ioaddr = dev->base_addr;
-	long mdio_addr = ioaddr + CSR9;
-
-	/* Establish sync by sending 32 logic ones. */
-	for (i = 32; i >= 0; i--) {
-		outl(MDIO_ENB | MDIO_DATA_WRITE1, mdio_addr);
-		mdio_delay();
-		outl(MDIO_ENB | MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
-		mdio_delay();
-	}
-	/* Shift the command bits out. */
-	for (i = 31; i >= 0; i--) {
-		int dataval = (cmd & (1 << i)) ? MDIO_DATA_WRITE1 : 0;
-		outl(MDIO_ENB | dataval, mdio_addr);
-		mdio_delay();
-		outl(MDIO_ENB | dataval | MDIO_SHIFT_CLK, mdio_addr);
-		mdio_delay();
-	}
-	/* Clear out extra bits. */
-	for (i = 2; i > 0; i--) {
-		outl(MDIO_ENB_IN, mdio_addr);
-		mdio_delay();
-		outl(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
-		mdio_delay();
-	}
-	return;
-}
-
-
-static void
-xircom_up(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	long ioaddr = dev->base_addr;
-	int i;
-
-	xircom_init_ring(dev);
-	/* Clear the tx ring */
-	for (i = 0; i < TX_RING_SIZE; i++) {
-		tp->tx_skbuff[i] = NULL;
-		tp->tx_ring[i].status = 0;
-	}
-
-	if (xircom_debug > 1)
-		printk(KERN_DEBUG "%s: xircom_up() irq %d.\n", dev->name, dev->irq);
-
-	outl(virt_to_bus(tp->rx_ring), ioaddr + CSR3);
-	outl(virt_to_bus(tp->tx_ring), ioaddr + CSR4);
-
-	tp->saved_if_port = dev->if_port;
-	if (dev->if_port == 0)
-		dev->if_port = tp->default_port;
-
-	tp->csr6 = TxThresh10 /*| FullDuplexBit*/;						/* XXX: why 10 and not 100? */
-
-	set_rx_mode(dev);
-
-	/* Start the chip's Tx to process setup frame. */
-	outl_CSR6(tp->csr6, ioaddr);
-	outl_CSR6(tp->csr6 | EnableTx, ioaddr);
-
-	/* Acknowledge all outstanding interrupts sources */
-	outl(xircom_tbl[tp->chip_id].valid_intrs, ioaddr + CSR5);
-	/* Enable interrupts by setting the interrupt mask. */
-	outl(xircom_tbl[tp->chip_id].valid_intrs, ioaddr + CSR7);
-	/* Enable Rx */
-	outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
-	/* Rx poll demand */
-	outl(0, ioaddr + CSR2);
-
-	/* Tell the net layer we're ready */
-	netif_start_queue (dev);
-
-	/* Check current media state */
-	xircom_media_change(dev);
-
-	if (xircom_debug > 2) {
-		printk(KERN_DEBUG "%s: Done xircom_up(), CSR0 %8.8x, CSR5 %8.8x CSR6 %8.8x.\n",
-			   dev->name, inl(ioaddr + CSR0), inl(ioaddr + CSR5),
-			   inl(ioaddr + CSR6));
-	}
-}
-
-
-static int
-xircom_open(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-
-	if (request_irq(dev->irq, &xircom_interrupt, SA_SHIRQ, dev->name, dev))
-		return -EAGAIN;
-
-	xircom_up(dev);
-	tp->open = 1;
-
-	return 0;
-}
-
-
-static void xircom_tx_timeout(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	long ioaddr = dev->base_addr;
-
-	if (media_cap[dev->if_port] & MediaIsMII) {
-		/* Do nothing -- the media monitor should handle this. */
-		if (xircom_debug > 1)
-			printk(KERN_WARNING "%s: Transmit timeout using MII device.\n",
-				   dev->name);
-	}
-
-#if defined(way_too_many_messages)
-	if (xircom_debug > 3) {
-		int i;
-		for (i = 0; i < RX_RING_SIZE; i++) {
-			u8 *buf = (u8 *)(tp->rx_ring[i].buffer1);
-			int j;
-			printk(KERN_DEBUG "%2d: %8.8x %8.8x %8.8x %8.8x  "
-				   "%2.2x %2.2x %2.2x.\n",
-				   i, (unsigned int)tp->rx_ring[i].status,
-				   (unsigned int)tp->rx_ring[i].length,
-				   (unsigned int)tp->rx_ring[i].buffer1,
-				   (unsigned int)tp->rx_ring[i].buffer2,
-				   buf[0], buf[1], buf[2]);
-			for (j = 0; buf[j] != 0xee && j < 1600; j++)
-				if (j < 100) printk(" %2.2x", buf[j]);
-			printk(" j=%d.\n", j);
-		}
-		printk(KERN_DEBUG "  Rx ring %8.8x: ", (int)tp->rx_ring);
-		for (i = 0; i < RX_RING_SIZE; i++)
-			printk(" %8.8x", (unsigned int)tp->rx_ring[i].status);
-		printk("\n" KERN_DEBUG "  Tx ring %8.8x: ", (int)tp->tx_ring);
-		for (i = 0; i < TX_RING_SIZE; i++)
-			printk(" %8.8x", (unsigned int)tp->tx_ring[i].status);
-		printk("\n");
-	}
-#endif
-
-	/* Stop and restart the chip's Tx/Rx processes . */
-	outl_CSR6(tp->csr6 | EnableRx, ioaddr);
-	outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
-	/* Trigger an immediate transmit demand. */
-	outl(0, ioaddr + CSR1);
-
-	dev->trans_start = jiffies;
-	netif_wake_queue (dev);
-	tp->stats.tx_errors++;
-}
-
-
-/* Initialize the Rx and Tx rings, along with various 'dev' bits. */
-static void xircom_init_ring(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	int i;
-
-	tp->tx_full = 0;
-	tp->cur_rx = tp->cur_tx = 0;
-	tp->dirty_rx = tp->dirty_tx = 0;
-
-	for (i = 0; i < RX_RING_SIZE; i++) {
-		tp->rx_ring[i].status = 0;
-		tp->rx_ring[i].length = PKT_BUF_SZ;
-		tp->rx_ring[i].buffer2 = virt_to_bus(&tp->rx_ring[i+1]);
-		tp->rx_skbuff[i] = NULL;
-	}
-	/* Mark the last entry as wrapping the ring. */
-	tp->rx_ring[i-1].length = PKT_BUF_SZ | Rx1RingWrap;
-	tp->rx_ring[i-1].buffer2 = virt_to_bus(&tp->rx_ring[0]);
-
-	for (i = 0; i < RX_RING_SIZE; i++) {
-		/* Note the receive buffer must be longword aligned.
-		   dev_alloc_skb() provides 16 byte alignment.  But do *not*
-		   use skb_reserve() to align the IP header! */
-		struct sk_buff *skb = dev_alloc_skb(PKT_BUF_SZ);
-		tp->rx_skbuff[i] = skb;
-		if (skb == NULL)
-			break;
-		skb->dev = dev;			/* Mark as being used by this device. */
-		tp->rx_ring[i].status = Rx0DescOwned;	/* Owned by Xircom chip */
-		tp->rx_ring[i].buffer1 = virt_to_bus(skb->data);
-	}
-	tp->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
-
-	/* The Tx buffer descriptor is filled in as needed, but we
-	   do need to clear the ownership bit. */
-	for (i = 0; i < TX_RING_SIZE; i++) {
-		tp->tx_skbuff[i] = NULL;
-		tp->tx_ring[i].status = 0;
-		tp->tx_ring[i].buffer2 = virt_to_bus(&tp->tx_ring[i+1]);
-#ifdef CARDBUS
-		if (tp->chip_id == X3201_3)
-			tp->tx_aligned_skbuff[i] = dev_alloc_skb(PKT_BUF_SZ);
-#endif /* CARDBUS */
-	}
-	tp->tx_ring[i-1].buffer2 = virt_to_bus(&tp->tx_ring[0]);
-}
-
-
-static int
-xircom_start_xmit(struct sk_buff *skb, struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	int entry;
-	u32 flag;
-
-	/* Caution: the write order is important here, set the base address
-	   with the "ownership" bits last. */
-
-	/* Calculate the next Tx descriptor entry. */
-	entry = tp->cur_tx % TX_RING_SIZE;
-
-	tp->tx_skbuff[entry] = skb;
-#ifdef CARDBUS
-	if (tp->chip_id == X3201_3) {
-		memcpy(tp->tx_aligned_skbuff[entry]->data,skb->data,skb->len);
-		tp->tx_ring[entry].buffer1 = virt_to_bus(tp->tx_aligned_skbuff[entry]->data);
-	} else
-#endif
-		tp->tx_ring[entry].buffer1 = virt_to_bus(skb->data);
-
-	if (tp->cur_tx - tp->dirty_tx < TX_RING_SIZE/2) {/* Typical path */
-		flag = Tx1WholePkt; /* No interrupt */
-	} else if (tp->cur_tx - tp->dirty_tx == TX_RING_SIZE/2) {
-		flag = Tx1WholePkt | Tx1ComplIntr; /* Tx-done intr. */
-	} else if (tp->cur_tx - tp->dirty_tx < TX_RING_SIZE - 2) {
-		flag = Tx1WholePkt; /* No Tx-done intr. */
-	} else {
-		/* Leave room for set_rx_mode() to fill entries. */
-		flag = Tx1WholePkt | Tx1ComplIntr; /* Tx-done intr. */
-		tp->tx_full = 1;
-	}
-	if (entry == TX_RING_SIZE - 1)
-		flag |= Tx1WholePkt | Tx1ComplIntr | Tx1RingWrap;
-
-	tp->tx_ring[entry].length = skb->len | flag;
-	tp->tx_ring[entry].status = Tx0DescOwned;	/* Pass ownership to the chip. */
-	tp->cur_tx++;
-	if (tp->tx_full)
-		netif_stop_queue (dev);
-	else
-		netif_wake_queue (dev);
-
-	/* Trigger an immediate transmit demand. */
-	outl(0, dev->base_addr + CSR1);
-
-	dev->trans_start = jiffies;
-
-	return 0;
-}
-
-
-static void xircom_media_change(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	long ioaddr = dev->base_addr;
-	u16 reg0, reg1, reg4, reg5;
-	u32 csr6 = inl(ioaddr + CSR6), newcsr6;
-
-	/* reset status first */
-	mdio_read(dev, tp->phys[0], MII_BMCR);
-	mdio_read(dev, tp->phys[0], MII_BMSR);
-
-	reg0 = mdio_read(dev, tp->phys[0], MII_BMCR);
-	reg1 = mdio_read(dev, tp->phys[0], MII_BMSR);
-
-	if (reg1 & BMSR_LSTATUS) {
-		/* link is up */
-		if (reg0 & BMCR_ANENABLE) {
-			/* autonegotiation is enabled */
-			reg4 = mdio_read(dev, tp->phys[0], MII_ADVERTISE);
-			reg5 = mdio_read(dev, tp->phys[0], MII_LPA);
-			if (reg4 & ADVERTISE_100FULL && reg5 & LPA_100FULL) {
-				tp->speed100 = 1;
-				tp->full_duplex = 1;
-			} else if (reg4 & ADVERTISE_100HALF && reg5 & LPA_100HALF) {
-				tp->speed100 = 1;
-				tp->full_duplex = 0;
-			} else if (reg4 & ADVERTISE_10FULL && reg5 & LPA_10FULL) {
-				tp->speed100 = 0;
-				tp->full_duplex = 1;
-			} else {
-				tp->speed100 = 0;
-				tp->full_duplex = 0;
-			}
-		} else {
-			/* autonegotiation is disabled */
-			if (reg0 & BMCR_SPEED100)
-				tp->speed100 = 1;
-			else
-				tp->speed100 = 0;
-			if (reg0 & BMCR_FULLDPLX)
-				tp->full_duplex = 1;
-			else
-				tp->full_duplex = 0;
-		}
-		printk(KERN_DEBUG "%s: Link is up, running at %sMbit %s-duplex\n",
-		       dev->name,
-		       tp->speed100 ? "100" : "10",
-		       tp->full_duplex ? "full" : "half");
-		netif_carrier_on(dev);
-		newcsr6 = csr6 & ~FullDuplexBit;
-		if (tp->full_duplex)
-			newcsr6 |= FullDuplexBit;
-		if (newcsr6 != csr6)
-			outl_CSR6(newcsr6, ioaddr + CSR6);
-	} else {
-		printk(KERN_DEBUG "%s: Link is down\n", dev->name);
-		netif_carrier_off(dev);
-	}
-}
-
-
-static void check_duplex(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	u16 reg0;
-
-	mdio_write(dev, tp->phys[0], MII_BMCR, BMCR_RESET);
-	udelay(500);
-	while (mdio_read(dev, tp->phys[0], MII_BMCR) & BMCR_RESET);
-
-	reg0 = mdio_read(dev, tp->phys[0], MII_BMCR);
-	mdio_write(dev, tp->phys[0], MII_ADVERTISE, tp->advertising[0]);
-
-	if (tp->autoneg) {
-		reg0 &= ~(BMCR_SPEED100 | BMCR_FULLDPLX);
-		reg0 |= BMCR_ANENABLE | BMCR_ANRESTART;
-	} else {
-		reg0 &= ~(BMCR_ANENABLE | BMCR_ANRESTART);
-		if (tp->speed100)
-			reg0 |= BMCR_SPEED100;
-		if (tp->full_duplex)
-			reg0 |= BMCR_FULLDPLX;
-		printk(KERN_DEBUG "%s: Link forced to %sMbit %s-duplex\n",
-		       dev->name,
-		       tp->speed100 ? "100" : "10",
-		       tp->full_duplex ? "full" : "half");
-	}
-	mdio_write(dev, tp->phys[0], MII_BMCR, reg0);
-}
-
-
-/* The interrupt handler does all of the Rx thread work and cleans up
-   after the Tx thread. */
-static irqreturn_t xircom_interrupt(int irq, void *dev_instance, struct pt_regs *regs)
-{
-	struct net_device *dev = dev_instance;
-	struct xircom_private *tp = netdev_priv(dev);
-	long ioaddr = dev->base_addr;
-	int csr5, work_budget = max_interrupt_work;
-	int handled = 0;
-
-	spin_lock (&tp->lock);
-
-	do {
-		csr5 = inl(ioaddr + CSR5);
-		/* Acknowledge all of the current interrupt sources ASAP. */
-		outl(csr5 & 0x0001ffff, ioaddr + CSR5);
-
-		if (xircom_debug > 4)
-			printk(KERN_DEBUG "%s: interrupt  csr5=%#8.8x new csr5=%#8.8x.\n",
-				   dev->name, csr5, inl(dev->base_addr + CSR5));
-
-		if (csr5 == 0xffffffff)
-			break;	/* all bits set, assume PCMCIA card removed */
-
-		if ((csr5 & (NormalIntr|AbnormalIntr)) == 0)
-			break;
-
-		handled = 1;
-
-		if (csr5 & (RxIntr | RxNoBuf))
-			work_budget -= xircom_rx(dev);
-
-		if (csr5 & (TxNoBuf | TxDied | TxIntr)) {
-			unsigned int dirty_tx;
-
-			for (dirty_tx = tp->dirty_tx; tp->cur_tx - dirty_tx > 0;
-				 dirty_tx++) {
-				int entry = dirty_tx % TX_RING_SIZE;
-				int status = tp->tx_ring[entry].status;
-
-				if (status < 0)
-					break;			/* It still hasn't been Txed */
-				/* Check for Rx filter setup frames. */
-				if (tp->tx_skbuff[entry] == NULL)
-				  continue;
-
-				if (status & Tx0DescError) {
-					/* There was an major error, log it. */
-#ifndef final_version
-					if (xircom_debug > 1)
-						printk(KERN_DEBUG "%s: Transmit error, Tx status %8.8x.\n",
-							   dev->name, status);
-#endif
-					tp->stats.tx_errors++;
-					if (status & Tx0ManyColl) {
-						tp->stats.tx_aborted_errors++;
-					}
-					if (status & Tx0NoCarrier) tp->stats.tx_carrier_errors++;
-					if (status & Tx0LateColl) tp->stats.tx_window_errors++;
-					if (status & Tx0Underflow) tp->stats.tx_fifo_errors++;
-				} else {
-					tp->stats.tx_bytes += tp->tx_ring[entry].length & 0x7ff;
-					tp->stats.collisions += (status >> 3) & 15;
-					tp->stats.tx_packets++;
-				}
-
-				/* Free the original skb. */
-				dev_kfree_skb_irq(tp->tx_skbuff[entry]);
-				tp->tx_skbuff[entry] = NULL;
-			}
-
-#ifndef final_version
-			if (tp->cur_tx - dirty_tx > TX_RING_SIZE) {
-				printk(KERN_ERR "%s: Out-of-sync dirty pointer, %d vs. %d, full=%d.\n",
-					   dev->name, dirty_tx, tp->cur_tx, tp->tx_full);
-				dirty_tx += TX_RING_SIZE;
-			}
-#endif
-
-			if (tp->tx_full &&
-			    tp->cur_tx - dirty_tx  < TX_RING_SIZE - 2)
-				/* The ring is no longer full */
-				tp->tx_full = 0;
-
-			if (tp->tx_full)
-				netif_stop_queue (dev);
-			else
-				netif_wake_queue (dev);
-
-			tp->dirty_tx = dirty_tx;
-			if (csr5 & TxDied) {
-				if (xircom_debug > 2)
-					printk(KERN_WARNING "%s: The transmitter stopped."
-						   "  CSR5 is %x, CSR6 %x, new CSR6 %x.\n",
-						   dev->name, csr5, inl(ioaddr + CSR6), tp->csr6);
-				outl_CSR6(tp->csr6 | EnableRx, ioaddr);
-				outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
-			}
-		}
-
-		/* Log errors. */
-		if (csr5 & AbnormalIntr) {	/* Abnormal error summary bit. */
-			if (csr5 & LinkChange)
-				xircom_media_change(dev);
-			if (csr5 & TxFIFOUnderflow) {
-				if ((tp->csr6 & TxThreshMask) != TxThreshMask)
-					tp->csr6 += (1 << TxThreshShift);	/* Bump up the Tx threshold */
-				else
-					tp->csr6 |= TxStoreForw;  /* Store-n-forward. */
-				/* Restart the transmit process. */
-				outl_CSR6(tp->csr6 | EnableRx, ioaddr);
-				outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
-			}
-			if (csr5 & RxDied) {		/* Missed a Rx frame. */
-				tp->stats.rx_errors++;
-				tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
-				outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
-			}
-			/* Clear all error sources, included undocumented ones! */
-			outl(0x0800f7ba, ioaddr + CSR5);
-		}
-		if (--work_budget < 0) {
-			if (xircom_debug > 1)
-				printk(KERN_WARNING "%s: Too much work during an interrupt, "
-					   "csr5=0x%8.8x.\n", dev->name, csr5);
-			/* Acknowledge all interrupt sources. */
-			outl(0x8001ffff, ioaddr + CSR5);
-			break;
-		}
-	} while (1);
-
-	if (xircom_debug > 3)
-		printk(KERN_DEBUG "%s: exiting interrupt, csr5=%#4.4x.\n",
-			   dev->name, inl(ioaddr + CSR5));
-
-	spin_unlock (&tp->lock);
-	return IRQ_RETVAL(handled);
-}
-
-
-static int
-xircom_rx(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	int entry = tp->cur_rx % RX_RING_SIZE;
-	int rx_work_limit = tp->dirty_rx + RX_RING_SIZE - tp->cur_rx;
-	int work_done = 0;
-
-	if (xircom_debug > 4)
-		printk(KERN_DEBUG " In xircom_rx(), entry %d %8.8x.\n", entry,
-			   tp->rx_ring[entry].status);
-	/* If we own the next entry, it's a new packet. Send it up. */
-	while (tp->rx_ring[entry].status >= 0) {
-		s32 status = tp->rx_ring[entry].status;
-
-		if (xircom_debug > 5)
-			printk(KERN_DEBUG " In xircom_rx(), entry %d %8.8x.\n", entry,
-				   tp->rx_ring[entry].status);
-		if (--rx_work_limit < 0)
-			break;
-		if ((status & 0x38008300) != 0x0300) {
-			if ((status & 0x38000300) != 0x0300) {
-				/* Ignore earlier buffers. */
-				if ((status & 0xffff) != 0x7fff) {
-					if (xircom_debug > 1)
-						printk(KERN_WARNING "%s: Oversized Ethernet frame "
-							   "spanned multiple buffers, status %8.8x!\n",
-							   dev->name, status);
-					tp->stats.rx_length_errors++;
-				}
-			} else if (status & Rx0DescError) {
-				/* There was a fatal error. */
-				if (xircom_debug > 2)
-					printk(KERN_DEBUG "%s: Receive error, Rx status %8.8x.\n",
-						   dev->name, status);
-				tp->stats.rx_errors++; /* end of a packet.*/
-				if (status & (Rx0Runt | Rx0HugeFrame)) tp->stats.rx_length_errors++;
-				if (status & Rx0CRCError) tp->stats.rx_crc_errors++;
-			}
-		} else {
-			/* Omit the four octet CRC from the length. */
-			short pkt_len = ((status >> 16) & 0x7ff) - 4;
-			struct sk_buff *skb;
-
-#ifndef final_version
-			if (pkt_len > 1518) {
-				printk(KERN_WARNING "%s: Bogus packet size of %d (%#x).\n",
-					   dev->name, pkt_len, pkt_len);
-				pkt_len = 1518;
-				tp->stats.rx_length_errors++;
-			}
-#endif
-			/* Check if the packet is long enough to accept without copying
-			   to a minimally-sized skbuff. */
-			if (pkt_len < rx_copybreak
-				&& (skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
-				skb->dev = dev;
-				skb_reserve(skb, 2);	/* 16 byte align the IP header */
-#if ! defined(__alpha__)
-				eth_copy_and_sum(skb, bus_to_virt(tp->rx_ring[entry].buffer1),
-								 pkt_len, 0);
-				skb_put(skb, pkt_len);
-#else
-				memcpy(skb_put(skb, pkt_len),
-					   bus_to_virt(tp->rx_ring[entry].buffer1), pkt_len);
-#endif
-				work_done++;
-			} else { 	/* Pass up the skb already on the Rx ring. */
-				skb_put(skb = tp->rx_skbuff[entry], pkt_len);
-				tp->rx_skbuff[entry] = NULL;
-			}
-			skb->protocol = eth_type_trans(skb, dev);
-			netif_rx(skb);
-			dev->last_rx = jiffies;
-			tp->stats.rx_packets++;
-			tp->stats.rx_bytes += pkt_len;
-		}
-		entry = (++tp->cur_rx) % RX_RING_SIZE;
-	}
-
-	/* Refill the Rx ring buffers. */
-	for (; tp->cur_rx - tp->dirty_rx > 0; tp->dirty_rx++) {
-		entry = tp->dirty_rx % RX_RING_SIZE;
-		if (tp->rx_skbuff[entry] == NULL) {
-			struct sk_buff *skb;
-			skb = tp->rx_skbuff[entry] = dev_alloc_skb(PKT_BUF_SZ);
-			if (skb == NULL)
-				break;
-			skb->dev = dev;			/* Mark as being used by this device. */
-			tp->rx_ring[entry].buffer1 = virt_to_bus(skb->data);
-			work_done++;
-		}
-		tp->rx_ring[entry].status = Rx0DescOwned;
-	}
-
-	return work_done;
-}
-
-
-static void
-xircom_down(struct net_device *dev)
-{
-	long ioaddr = dev->base_addr;
-	struct xircom_private *tp = netdev_priv(dev);
-
-	/* Disable interrupts by clearing the interrupt mask. */
-	outl(0, ioaddr + CSR7);
-	/* Stop the chip's Tx and Rx processes. */
-	outl_CSR6(inl(ioaddr + CSR6) & ~EnableTxRx, ioaddr);
-
-	if (inl(ioaddr + CSR6) != 0xffffffff)
-		tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
-
-	dev->if_port = tp->saved_if_port;
-}
-
-
-static int
-xircom_close(struct net_device *dev)
-{
-	long ioaddr = dev->base_addr;
-	struct xircom_private *tp = netdev_priv(dev);
-	int i;
-
-	if (xircom_debug > 1)
-		printk(KERN_DEBUG "%s: Shutting down ethercard, status was %2.2x.\n",
-			   dev->name, inl(ioaddr + CSR5));
-
-	netif_stop_queue(dev);
-
-	if (netif_device_present(dev))
-		xircom_down(dev);
-
-	free_irq(dev->irq, dev);
-
-	/* Free all the skbuffs in the Rx queue. */
-	for (i = 0; i < RX_RING_SIZE; i++) {
-		struct sk_buff *skb = tp->rx_skbuff[i];
-		tp->rx_skbuff[i] = NULL;
-		tp->rx_ring[i].status = 0;		/* Not owned by Xircom chip. */
-		tp->rx_ring[i].length = 0;
-		tp->rx_ring[i].buffer1 = 0xBADF00D0; /* An invalid address. */
-		if (skb) {
-			dev_kfree_skb(skb);
-		}
-	}
-	for (i = 0; i < TX_RING_SIZE; i++) {
-		if (tp->tx_skbuff[i])
-			dev_kfree_skb(tp->tx_skbuff[i]);
-		tp->tx_skbuff[i] = NULL;
-	}
-
-	tp->open = 0;
-	return 0;
-}
-
-
-static struct net_device_stats *xircom_get_stats(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	long ioaddr = dev->base_addr;
-
-	if (netif_device_present(dev))
-		tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
-
-	return &tp->stats;
-}
-
-static int xircom_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	ecmd->supported =
-			SUPPORTED_10baseT_Half |
-			SUPPORTED_10baseT_Full |
-			SUPPORTED_100baseT_Half |
-			SUPPORTED_100baseT_Full |
-			SUPPORTED_Autoneg |
-			SUPPORTED_MII;
-
-	ecmd->advertising = ADVERTISED_MII;
-	if (tp->advertising[0] & ADVERTISE_10HALF)
-		ecmd->advertising |= ADVERTISED_10baseT_Half;
-	if (tp->advertising[0] & ADVERTISE_10FULL)
-		ecmd->advertising |= ADVERTISED_10baseT_Full;
-	if (tp->advertising[0] & ADVERTISE_100HALF)
-		ecmd->advertising |= ADVERTISED_100baseT_Half;
-	if (tp->advertising[0] & ADVERTISE_100FULL)
-		ecmd->advertising |= ADVERTISED_100baseT_Full;
-	if (tp->autoneg) {
-		ecmd->advertising |= ADVERTISED_Autoneg;
-		ecmd->autoneg = AUTONEG_ENABLE;
-	} else
-		ecmd->autoneg = AUTONEG_DISABLE;
-
-	ecmd->port = PORT_MII;
-	ecmd->transceiver = XCVR_INTERNAL;
-	ecmd->phy_address = tp->phys[0];
-	ecmd->speed = tp->speed100 ? SPEED_100 : SPEED_10;
-	ecmd->duplex = tp->full_duplex ? DUPLEX_FULL : DUPLEX_HALF;
-	ecmd->maxtxpkt = TX_RING_SIZE / 2;
-	ecmd->maxrxpkt = 0;
-	return 0;
-}
-
-static int xircom_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	u16 autoneg, speed100, full_duplex;
-
-	autoneg = (ecmd->autoneg == AUTONEG_ENABLE);
-	speed100 = (ecmd->speed == SPEED_100);
-	full_duplex = (ecmd->duplex == DUPLEX_FULL);
-
-	tp->autoneg = autoneg;
-	if (speed100 != tp->speed100 ||
-	    full_duplex != tp->full_duplex) {
-		tp->speed100 = speed100;
-		tp->full_duplex = full_duplex;
-		/* change advertising bits */
-		tp->advertising[0] &= ~(ADVERTISE_10HALF |
-				     ADVERTISE_10FULL |
-				     ADVERTISE_100HALF |
-				     ADVERTISE_100FULL |
-				     ADVERTISE_100BASE4);
-		if (speed100) {
-			if (full_duplex)
-				tp->advertising[0] |= ADVERTISE_100FULL;
-			else
-				tp->advertising[0] |= ADVERTISE_100HALF;
-		} else {
-			if (full_duplex)
-				tp->advertising[0] |= ADVERTISE_10FULL;
-			else
-				tp->advertising[0] |= ADVERTISE_10HALF;
-		}
-	}
-	check_duplex(dev);
-	return 0;
-}
-
-static void xircom_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	strcpy(info->driver, DRV_NAME);
-	strcpy(info->version, DRV_VERSION);
-	strcpy(info->bus_info, pci_name(tp->pdev));
-}
-
-static struct ethtool_ops ops = {
-	.get_settings = xircom_get_settings,
-	.set_settings = xircom_set_settings,
-	.get_drvinfo = xircom_get_drvinfo,
-};
-
-/* Provide ioctl() calls to examine the MII xcvr state. */
-static int xircom_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	u16 *data = (u16 *)&rq->ifr_ifru;
-	int phy = tp->phys[0] & 0x1f;
-	unsigned long flags;
-
-	switch(cmd) {
-	/* Legacy mii-diag interface */
-	case SIOCGMIIPHY:		/* Get address of MII PHY in use. */
-		if (tp->mii_cnt)
-			data[0] = phy;
-		else
-			return -ENODEV;
-		return 0;
-	case SIOCGMIIREG:		/* Read MII PHY register. */
-		save_flags(flags);
-		cli();
-		data[3] = mdio_read(dev, data[0] & 0x1f, data[1] & 0x1f);
-		restore_flags(flags);
-		return 0;
-	case SIOCSMIIREG:		/* Write MII PHY register. */
-		if (!capable(CAP_NET_ADMIN))
-			return -EPERM;
-		save_flags(flags);
-		cli();
-		if (data[0] == tp->phys[0]) {
-			u16 value = data[2];
-			switch (data[1]) {
-			case 0:
-				if (value & (BMCR_RESET | BMCR_ANENABLE))
-					/* Autonegotiation. */
-					tp->autoneg = 1;
-				else {
-					tp->full_duplex = (value & BMCR_FULLDPLX) ? 1 : 0;
-					tp->autoneg = 0;
-				}
-				break;
-			case 4:
-				tp->advertising[0] = value;
-				break;
-			}
-			check_duplex(dev);
-		}
-		mdio_write(dev, data[0] & 0x1f, data[1] & 0x1f, data[2]);
-		restore_flags(flags);
-		return 0;
-	default:
-		return -EOPNOTSUPP;
-	}
-
-	return -EOPNOTSUPP;
-}
-
-/* Set or clear the multicast filter for this adaptor.
-   Note that we only use exclusion around actually queueing the
-   new frame, not around filling tp->setup_frame.  This is non-deterministic
-   when re-entered but still correct. */
-static void set_rx_mode(struct net_device *dev)
-{
-	struct xircom_private *tp = netdev_priv(dev);
-	struct dev_mc_list *mclist;
-	long ioaddr = dev->base_addr;
-	int csr6 = inl(ioaddr + CSR6);
-	u16 *eaddrs, *setup_frm;
-	u32 tx_flags;
-	int i;
-
-	tp->csr6 &= ~(AllMultiBit | PromiscBit | HashFilterBit);
-	csr6 &= ~(AllMultiBit | PromiscBit | HashFilterBit);
-	if (dev->flags & IFF_PROMISC) {			/* Set promiscuous. */
-		tp->csr6 |= PromiscBit;
-		csr6 |= PromiscBit;
-		goto out;
-	}
-
-	if ((dev->mc_count > 1000) || (dev->flags & IFF_ALLMULTI)) {
-		/* Too many to filter well -- accept all multicasts. */
-		tp->csr6 |= AllMultiBit;
-		csr6 |= AllMultiBit;
-		goto out;
-	}
-
-	tx_flags = Tx1WholePkt | Tx1SetupPkt | PKT_SETUP_SZ;
-
-	/* Note that only the low-address shortword of setup_frame is valid! */
-	setup_frm = tp->setup_frame;
-	mclist = dev->mc_list;
-
-	/* Fill the first entry with our physical address. */
-	eaddrs = (u16 *)dev->dev_addr;
-	*setup_frm = cpu_to_le16(eaddrs[0]); setup_frm += 2;
-	*setup_frm = cpu_to_le16(eaddrs[1]); setup_frm += 2;
-	*setup_frm = cpu_to_le16(eaddrs[2]); setup_frm += 2;
-
-	if (dev->mc_count > 14) { /* Must use a multicast hash table. */
-		u32 *hash_table = (u32 *)(tp->setup_frame + 4 * 12);
-		u32 hash, hash2;
-
-		tx_flags |= Tx1HashSetup;
-		tp->csr6 |= HashFilterBit;
-		csr6 |= HashFilterBit;
-
-		/* Fill the unused 3 entries with the broadcast address.
-		   At least one entry *must* contain the broadcast address!!!*/
-		for (i = 0; i < 3; i++) {
-			*setup_frm = 0xffff; setup_frm += 2;
-			*setup_frm = 0xffff; setup_frm += 2;
-			*setup_frm = 0xffff; setup_frm += 2;
-		}
-
-		/* Truly brain-damaged hash filter layout */
-		/* XXX: not sure if I should take the last or the first 9 bits */
-		for (i = 0; i < dev->mc_count; i++, mclist = mclist->next) {
-			u32 *hptr;
-			hash = ether_crc(ETH_ALEN, mclist->dmi_addr) & 0x1ff;
-			if (hash < 384) {
-				hash2 = hash + ((hash >> 4) << 4) +
-					((hash >> 5) << 5);
-			} else {
-				hash -= 384;
-				hash2 = 64 + hash + (hash >> 4) * 80;
-			}
-			hptr = &hash_table[hash2 & ~0x1f];
-			*hptr |= cpu_to_le32(1 << (hash2 & 0x1f));
-		}
-	} else {
-		/* We have <= 14 mcast addresses so we can use Xircom's
-		   wonderful 16-address perfect filter. */
-		for (i = 0; i < dev->mc_count; i++, mclist = mclist->next) {
-			eaddrs = (u16 *)mclist->dmi_addr;
-			*setup_frm = cpu_to_le16(eaddrs[0]); setup_frm += 2;
-			*setup_frm = cpu_to_le16(eaddrs[1]); setup_frm += 2;
-			*setup_frm = cpu_to_le16(eaddrs[2]); setup_frm += 2;
-		}
-		/* Fill the unused entries with the broadcast address.
-		   At least one entry *must* contain the broadcast address!!!*/
-		for (; i < 15; i++) {
-			*setup_frm = 0xffff; setup_frm += 2;
-			*setup_frm = 0xffff; setup_frm += 2;
-			*setup_frm = 0xffff; setup_frm += 2;
-		}
-	}
-
-	/* Now add this frame to the Tx list. */
-	if (tp->cur_tx - tp->dirty_tx > TX_RING_SIZE - 2) {
-		/* Same setup recently queued, we need not add it. */
-		/* XXX: Huh? All it means is that the Tx list is full...*/
-	} else {
-		unsigned long flags;
-		unsigned int entry;
-		int dummy = -1;
-
-		save_flags(flags); cli();
-		entry = tp->cur_tx++ % TX_RING_SIZE;
-
-		if (entry != 0) {
-			/* Avoid a chip errata by prefixing a dummy entry. */
-			tp->tx_skbuff[entry] = NULL;
-			tp->tx_ring[entry].length =
-				(entry == TX_RING_SIZE - 1) ? Tx1RingWrap : 0;
-			tp->tx_ring[entry].buffer1 = 0;
-			/* race with chip, set Tx0DescOwned later */
-			dummy = entry;
-			entry = tp->cur_tx++ % TX_RING_SIZE;
-		}
-
-		tp->tx_skbuff[entry] = NULL;
-		/* Put the setup frame on the Tx list. */
-		if (entry == TX_RING_SIZE - 1)
-			tx_flags |= Tx1RingWrap;		/* Wrap ring. */
-		tp->tx_ring[entry].length = tx_flags;
-		tp->tx_ring[entry].buffer1 = virt_to_bus(tp->setup_frame);
-		tp->tx_ring[entry].status = Tx0DescOwned;
-		if (tp->cur_tx - tp->dirty_tx >= TX_RING_SIZE - 2) {
-			tp->tx_full = 1;
-			netif_stop_queue (dev);
-		}
-		if (dummy >= 0)
-			tp->tx_ring[dummy].status = Tx0DescOwned;
-		restore_flags(flags);
-		/* Trigger an immediate transmit demand. */
-		outl(0, ioaddr + CSR1);
-	}
-
-out:
-	outl_CSR6(csr6, ioaddr);
-}
-
-
-static struct pci_device_id xircom_pci_table[] = {
-  { 0x115D, 0x0003, PCI_ANY_ID, PCI_ANY_ID, 0, 0, X3201_3 },
-  {0},
-};
-MODULE_DEVICE_TABLE(pci, xircom_pci_table);
-
-
-#ifdef CONFIG_PM
-static int xircom_suspend(struct pci_dev *pdev, pm_message_t state)
-{
-	struct net_device *dev = pci_get_drvdata(pdev);
-	struct xircom_private *tp = netdev_priv(dev);
-	printk(KERN_INFO "xircom_suspend(%s)\n", dev->name);
-	if (tp->open)
-		xircom_down(dev);
-
-	pci_save_state(pdev);
-	pci_disable_device(pdev);
-	pci_set_power_state(pdev, 3);
-
-	return 0;
-}
-
-
-static int xircom_resume(struct pci_dev *pdev)
-{
-	struct net_device *dev = pci_get_drvdata(pdev);
-	struct xircom_private *tp = netdev_priv(dev);
-	printk(KERN_INFO "xircom_resume(%s)\n", dev->name);
-
-	pci_set_power_state(pdev,0);
-	pci_enable_device(pdev);
-	pci_restore_state(pdev);
-
-	/* Bring the chip out of sleep mode.
-	   Caution: Snooze mode does not work with some boards! */
-	if (xircom_tbl[tp->chip_id].flags & HAS_ACPI)
-		pci_write_config_dword(tp->pdev, PCI_POWERMGMT, 0);
-
-	transceiver_voodoo(dev);
-	if (xircom_tbl[tp->chip_id].flags & HAS_MII)
-		check_duplex(dev);
-
-	if (tp->open)
-		xircom_up(dev);
-	return 0;
-}
-#endif /* CONFIG_PM */
-
-
-static void __devexit xircom_remove_one(struct pci_dev *pdev)
-{
-	struct net_device *dev = pci_get_drvdata(pdev);
-
-	printk(KERN_INFO "xircom_remove_one(%s)\n", dev->name);
-	unregister_netdev(dev);
-	pci_release_regions(pdev);
-	free_netdev(dev);
-	pci_set_drvdata(pdev, NULL);
-}
-
-
-static struct pci_driver xircom_driver = {
-	.name		= DRV_NAME,
-	.id_table	= xircom_pci_table,
-	.probe		= xircom_init_one,
-	.remove		= __devexit_p(xircom_remove_one),
-#ifdef CONFIG_PM
-	.suspend	= xircom_suspend,
-	.resume		= xircom_resume
-#endif /* CONFIG_PM */
-};
-
-
-static int __init xircom_init(void)
-{
-/* when a module, this is printed whether or not devices are found in probe */
-#ifdef MODULE
-	printk(version);
-#endif
-	return pci_module_init(&xircom_driver);
-}
-
-
-static void __exit xircom_exit(void)
-{
-	pci_unregister_driver(&xircom_driver);
-}
-
-module_init(xircom_init)
-module_exit(xircom_exit)
-
-/*
- * Local variables:
- *  c-indent-level: 4
- *  c-basic-offset: 4
- *  tab-width: 4
- * End:
- */

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux