Hi,
Please pull from:
master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6.git/
to obtain following changes:
drivers/ide/Kconfig | 9 +
drivers/ide/ide-floppy.c | 6
drivers/ide/ide-iops.c | 6
drivers/ide/ide-taskfile.c | 2
drivers/ide/ide.c | 1
drivers/ide/legacy/ide-cs.c | 7 -
drivers/ide/pci/Makefile | 1
drivers/ide/pci/amd74xx.c | 3
drivers/ide/pci/cs5535.c | 305 ++++++++++++++++++++++++++++++++++++++++++++
drivers/ide/pci/cy82c693.c | 2
drivers/ide/pci/siimage.c | 9 +
drivers/scsi/ide-scsi.c | 5
include/asm-alpha/ide.h | 4
include/asm-i386/ide.h | 6
include/asm-sh/ide.h | 4
include/asm-sh64/ide.h | 4
include/linux/ide.h | 5
include/linux/pci_ids.h | 3
18 files changed, 352 insertions(+), 30 deletions(-)
Adrian Bunk:
ide: possible cleanups
Alan Cox:
ide: explain the PCI bus test we do in <asm-i386/ide.h>
Bjorn Helgaas:
ide: move CONFIG_IDE_MAX_HWIFS into linux/ide.h
Hannes Reinecke:
ide: incorrect device link for ide-cs
Jaya Kumar:
ide: CS5535 driver
John W. Linville:
siimage: enable interrupts on Adaptec SA-1210 card
Jordan Crouse:
ide: AMD Geode GX/LX support
Ondrej Zary:
ide-floppy: software eject not working with LS-120 drive
Willem Riede:
ide: ide-scsi fails to call idescsi_check_condition for things like "Medium not present"
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -539,6 +539,15 @@ config BLK_DEV_CS5530
It is safe to say Y to this question.
+config BLK_DEV_CS5535
+ tristate "AMD CS5535 chipset support"
+ depends on X86 && !X86_64
+ help
+ Include support for UDMA on the NSC/AMD CS5535 companion chipset.
+ This will automatically be detected and configured if found.
+
+ It is safe to say Y to this question.
+
config BLK_DEV_HPT34X
tristate "HPT34X chipset support"
help
diff --git a/drivers/ide/ide-floppy.c b/drivers/ide/ide-floppy.c
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -2038,11 +2038,9 @@ static int idefloppy_ioctl(struct inode
struct ide_floppy_obj *floppy = ide_floppy_g(bdev->bd_disk);
ide_drive_t *drive = floppy->drive;
void __user *argp = (void __user *)arg;
- int err = generic_ide_ioctl(drive, file, bdev, cmd, arg);
+ int err;
int prevent = (arg) ? 1 : 0;
idefloppy_pc_t pc;
- if (err != -EINVAL)
- return err;
switch (cmd) {
case CDROMEJECT:
@@ -2094,7 +2092,7 @@ static int idefloppy_ioctl(struct inode
case IDEFLOPPY_IOCTL_FORMAT_GET_PROGRESS:
return idefloppy_get_format_progress(drive, argp);
}
- return -EINVAL;
+ return generic_ide_ioctl(drive, file, bdev, cmd, arg);
}
static int idefloppy_media_changed(struct gendisk *disk)
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -104,8 +104,6 @@ void default_hwif_iops (ide_hwif_t *hwif
hwif->INSL = ide_insl;
}
-EXPORT_SYMBOL(default_hwif_iops);
-
/*
* MMIO operations, typically used for SATA controllers
*/
@@ -329,8 +327,6 @@ void default_hwif_transport(ide_hwif_t *
hwif->atapi_output_bytes = atapi_output_bytes;
}
-EXPORT_SYMBOL(default_hwif_transport);
-
/*
* Beginning of Taskfile OPCODE Library and feature sets.
*/
@@ -529,8 +525,6 @@ int wait_for_ready (ide_drive_t *drive,
return 0;
}
-EXPORT_SYMBOL(wait_for_ready);
-
/*
* This routine busy-waits for the drive status to be not "busy".
* It then checks the status for all of the "good" bits and none
diff --git a/drivers/ide/ide-taskfile.c b/drivers/ide/ide-taskfile.c
--- a/drivers/ide/ide-taskfile.c
+++ b/drivers/ide/ide-taskfile.c
@@ -161,8 +161,6 @@ ide_startstop_t do_rw_taskfile (ide_driv
return ide_stopped;
}
-EXPORT_SYMBOL(do_rw_taskfile);
-
/*
* set_multmode_intr() is invoked on completion of a WIN_SETMULT cmd.
*/
diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -803,6 +803,7 @@ found:
hwif->irq = hw->irq;
hwif->noprobe = 0;
hwif->chipset = hw->chipset;
+ hwif->gendev.parent = hw->dev;
if (!initializing) {
probe_hwif_init_with_fixup(hwif, fixup);
diff --git a/drivers/ide/legacy/ide-cs.c b/drivers/ide/legacy/ide-cs.c
--- a/drivers/ide/legacy/ide-cs.c
+++ b/drivers/ide/legacy/ide-cs.c
@@ -182,13 +182,14 @@ static void ide_detach(dev_link_t *link)
} /* ide_detach */
-static int idecs_register(unsigned long io, unsigned long ctl, unsigned long irq)
+static int idecs_register(unsigned long io, unsigned long ctl, unsigned long irq, struct pcmcia_device *handle)
{
hw_regs_t hw;
memset(&hw, 0, sizeof(hw));
ide_init_hwif_ports(&hw, io, ctl, NULL);
hw.irq = irq;
hw.chipset = ide_pci;
+ hw.dev = &handle->dev;
return ide_register_hw_with_fixup(&hw, NULL, ide_undecoded_slave);
}
@@ -327,12 +328,12 @@ static void ide_config(dev_link_t *link)
/* retry registration in case device is still spinning up */
for (hd = -1, i = 0; i < 10; i++) {
- hd = idecs_register(io_base, ctl_base, link->irq.AssignedIRQ);
+ hd = idecs_register(io_base, ctl_base, link->irq.AssignedIRQ, handle);
if (hd >= 0) break;
if (link->io.NumPorts1 == 0x20) {
outb(0x02, ctl_base + 0x10);
hd = idecs_register(io_base + 0x10, ctl_base + 0x10,
- link->irq.AssignedIRQ);
+ link->irq.AssignedIRQ, handle);
if (hd >= 0) {
io_base += 0x10;
ctl_base += 0x10;
diff --git a/drivers/ide/pci/Makefile b/drivers/ide/pci/Makefile
--- a/drivers/ide/pci/Makefile
+++ b/drivers/ide/pci/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_BLK_DEV_ATIIXP) += atiixp.
obj-$(CONFIG_BLK_DEV_CMD64X) += cmd64x.o
obj-$(CONFIG_BLK_DEV_CS5520) += cs5520.o
obj-$(CONFIG_BLK_DEV_CS5530) += cs5530.o
+obj-$(CONFIG_BLK_DEV_CS5535) += cs5535.o
obj-$(CONFIG_BLK_DEV_SC1200) += sc1200.o
obj-$(CONFIG_BLK_DEV_CY82C693) += cy82c693.o
obj-$(CONFIG_BLK_DEV_HPT34X) += hpt34x.o
diff --git a/drivers/ide/pci/amd74xx.c b/drivers/ide/pci/amd74xx.c
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -74,6 +74,7 @@ static struct amd_ide_chip {
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE, 0x50, AMD_UDMA_133 },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE, 0x50, AMD_UDMA_133 },
{ PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE, 0x50, AMD_UDMA_133 },
+ { PCI_DEVICE_ID_AMD_CS5536_IDE, 0x40, AMD_UDMA_100 },
{ 0 }
};
@@ -491,6 +492,7 @@ static ide_pci_device_t amd74xx_chipsets
/* 14 */ DECLARE_NV_DEV("NFORCE-MCP04"),
/* 15 */ DECLARE_NV_DEV("NFORCE-MCP51"),
/* 16 */ DECLARE_NV_DEV("NFORCE-MCP55"),
+ /* 17 */ DECLARE_AMD_DEV("AMD5536"),
};
static int __devinit amd74xx_probe(struct pci_dev *dev, const struct pci_device_id *id)
@@ -527,6 +529,7 @@ static struct pci_device_id amd74xx_pci_
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 14 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 15 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 16 },
+ { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 17 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, amd74xx_pci_tbl);
diff --git a/drivers/ide/pci/cs5535.c b/drivers/ide/pci/cs5535.c
new file mode 100644
--- /dev/null
+++ b/drivers/ide/pci/cs5535.c
@@ -0,0 +1,305 @@
+/*
+ * linux/drivers/ide/pci/cs5535.c
+ *
+ * Copyright (C) 2004-2005 Advanced Micro Devices, Inc.
+ *
+ * History:
+ * 09/20/2005 - Jaya Kumar <[email protected]>
+ * - Reworked tuneproc, set_drive, misc mods to prep for mainline
+ * - Work was sponsored by CIS (M) Sdn Bhd.
+ * Ported to Kernel 2.6.11 on June 26, 2005 by
+ * Wolfgang Zuleger <[email protected]>
+ * Alexander Kiausch <[email protected]>
+ * Originally developed by AMD for 2.4/2.6
+ *
+ * Development of this chipset driver was funded
+ * by the nice folks at National Semiconductor/AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * Documentation:
+ * CS5535 documentation available from AMD
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+
+#include "ide-timing.h"
+
+#define MSR_ATAC_BASE 0x51300000
+#define ATAC_GLD_MSR_CAP (MSR_ATAC_BASE+0)
+#define ATAC_GLD_MSR_CONFIG (MSR_ATAC_BASE+0x01)
+#define ATAC_GLD_MSR_SMI (MSR_ATAC_BASE+0x02)
+#define ATAC_GLD_MSR_ERROR (MSR_ATAC_BASE+0x03)
+#define ATAC_GLD_MSR_PM (MSR_ATAC_BASE+0x04)
+#define ATAC_GLD_MSR_DIAG (MSR_ATAC_BASE+0x05)
+#define ATAC_IO_BAR (MSR_ATAC_BASE+0x08)
+#define ATAC_RESET (MSR_ATAC_BASE+0x10)
+#define ATAC_CH0D0_PIO (MSR_ATAC_BASE+0x20)
+#define ATAC_CH0D0_DMA (MSR_ATAC_BASE+0x21)
+#define ATAC_CH0D1_PIO (MSR_ATAC_BASE+0x22)
+#define ATAC_CH0D1_DMA (MSR_ATAC_BASE+0x23)
+#define ATAC_PCI_ABRTERR (MSR_ATAC_BASE+0x24)
+#define ATAC_BM0_CMD_PRIM 0x00
+#define ATAC_BM0_STS_PRIM 0x02
+#define ATAC_BM0_PRD 0x04
+#define CS5535_CABLE_DETECT 0x48
+
+/* Format I PIO settings. We seperate out cmd and data for safer timings */
+
+static unsigned int cs5535_pio_cmd_timings[5] =
+{ 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131 };
+static unsigned int cs5535_pio_dta_timings[5] =
+{ 0xF7F4, 0xF173, 0x8141, 0x5131, 0x1131 };
+
+static unsigned int cs5535_mwdma_timings[3] =
+{ 0x7F0FFFF3, 0x7F035352, 0x7f024241 };
+
+static unsigned int cs5535_udma_timings[5] =
+{ 0x7F7436A1, 0x7F733481, 0x7F723261, 0x7F713161, 0x7F703061 };
+
+/* Macros to check if the register is the reset value - reset value is an
+ invalid timing and indicates the register has not been set previously */
+
+#define CS5535_BAD_PIO(timings) ( (timings&~0x80000000UL) == 0x00009172 )
+#define CS5535_BAD_DMA(timings) ( (timings & 0x000FFFFF) == 0x00077771 )
+
+/****
+ * cs5535_set_speed - Configure the chipset to the new speed
+ * @drive: Drive to set up
+ * @speed: desired speed
+ *
+ * cs5535_set_speed() configures the chipset to a new speed.
+ */
+static void cs5535_set_speed(ide_drive_t *drive, u8 speed)
+{
+
+ u32 reg = 0, dummy;
+ int unit = drive->select.b.unit;
+
+
+ /* Set the PIO timings */
+ if ((speed & XFER_MODE) == XFER_PIO) {
+ u8 pioa;
+ u8 piob;
+ u8 cmd;
+
+ pioa = speed - XFER_PIO_0;
+ piob = ide_get_best_pio_mode(&(drive->hwif->drives[!unit]),
+ 255, 4, NULL);
+ cmd = pioa < piob ? pioa : piob;
+
+ /* Write the speed of the current drive */
+ reg = (cs5535_pio_cmd_timings[cmd] << 16) |
+ cs5535_pio_dta_timings[pioa];
+ wrmsr(unit ? ATAC_CH0D1_PIO : ATAC_CH0D0_PIO, reg, 0);
+
+ /* And if nessesary - change the speed of the other drive */
+ rdmsr(unit ? ATAC_CH0D0_PIO : ATAC_CH0D1_PIO, reg, dummy);
+
+ if (((reg >> 16) & cs5535_pio_cmd_timings[cmd]) !=
+ cs5535_pio_cmd_timings[cmd]) {
+ reg &= 0x0000FFFF;
+ reg |= cs5535_pio_cmd_timings[cmd] << 16;
+ wrmsr(unit ? ATAC_CH0D0_PIO : ATAC_CH0D1_PIO, reg, 0);
+ }
+
+ /* Set bit 31 of the DMA register for PIO format 1 timings */
+ rdmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, dummy);
+ wrmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA,
+ reg | 0x80000000UL, 0);
+ } else {
+ rdmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, dummy);
+
+ reg &= 0x80000000UL; /* Preserve the PIO format bit */
+
+ if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_7)
+ reg |= cs5535_udma_timings[speed - XFER_UDMA_0];
+ else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+ reg |= cs5535_mwdma_timings[speed - XFER_MW_DMA_0];
+ else
+ return;
+
+ wrmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, 0);
+ }
+}
+
+static u8 cs5535_ratemask(ide_drive_t *drive)
+{
+ /* eighty93 will return 1 if it's 80core and capable of
+ exceeding udma2, 0 otherwise. we need ratemask to set
+ the max speed and if we can > udma2 then we return 2
+ which selects speed_max as udma4 which is the 5535's max
+ speed, and 1 selects udma2 which is the max for 40c */
+ if (!eighty_ninty_three(drive))
+ return 1;
+
+ return 2;
+}
+
+
+/****
+ * cs5535_set_drive - Configure the drive to the new speed
+ * @drive: Drive to set up
+ * @speed: desired speed
+ *
+ * cs5535_set_drive() configures the drive and the chipset to a
+ * new speed. It also can be called by upper layers.
+ */
+static int cs5535_set_drive(ide_drive_t *drive, u8 speed)
+{
+ speed = ide_rate_filter(cs5535_ratemask(drive), speed);
+ ide_config_drive_speed(drive, speed);
+ cs5535_set_speed(drive, speed);
+
+ return 0;
+}
+
+/****
+ * cs5535_tuneproc - PIO setup
+ * @drive: drive to set up
+ * @pio: mode to use (255 for 'best possible')
+ *
+ * A callback from the upper layers for PIO-only tuning.
+ */
+static void cs5535_tuneproc(ide_drive_t *drive, u8 xferspeed)
+{
+ u8 modes[] = { XFER_PIO_0, XFER_PIO_1, XFER_PIO_2, XFER_PIO_3,
+ XFER_PIO_4 };
+
+ /* cs5535 max pio is pio 4, best_pio will check the blacklist.
+ i think we don't need to rate_filter the incoming xferspeed
+ since we know we're only going to choose pio */
+ xferspeed = ide_get_best_pio_mode(drive, xferspeed, 4, NULL);
+ ide_config_drive_speed(drive, modes[xferspeed]);
+ cs5535_set_speed(drive, xferspeed);
+}
+
+static int cs5535_config_drive_for_dma(ide_drive_t *drive)
+{
+ u8 speed;
+
+ speed = ide_dma_speed(drive, cs5535_ratemask(drive));
+
+ /* If no DMA speed was available then let dma_check hit pio */
+ if (!speed) {
+ return 0;
+ }
+
+ cs5535_set_drive(drive, speed);
+ return ide_dma_enable(drive);
+}
+
+static int cs5535_dma_check(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct hd_driveid *id = drive->id;
+ u8 speed;
+
+ drive->init_speed = 0;
+
+ if ((id->capability & 1) && drive->autodma) {
+ if (ide_use_dma(drive)) {
+ if (cs5535_config_drive_for_dma(drive))
+ return hwif->ide_dma_on(drive);
+ }
+
+ goto fast_ata_pio;
+
+ } else if ((id->capability & 8) || (id->field_valid & 2)) {
+fast_ata_pio:
+ speed = ide_get_best_pio_mode(drive, 255, 4, NULL);
+ cs5535_set_drive(drive, speed);
+ return hwif->ide_dma_off_quietly(drive);
+ }
+ /* IORDY not supported */
+ return 0;
+}
+
+static u8 __devinit cs5535_cable_detect(struct pci_dev *dev)
+{
+ u8 bit;
+
+ /* if a 80 wire cable was detected */
+ pci_read_config_byte(dev, CS5535_CABLE_DETECT, &bit);
+ return (bit & 1);
+}
+
+/****
+ * init_hwif_cs5535 - Initialize one ide cannel
+ * @hwif: Channel descriptor
+ *
+ * This gets invoked by the IDE driver once for each channel. It
+ * performs channel-specific pre-initialization before drive probing.
+ *
+ */
+static void __devinit init_hwif_cs5535(ide_hwif_t *hwif)
+{
+ int i;
+
+ hwif->autodma = 0;
+
+ hwif->tuneproc = &cs5535_tuneproc;
+ hwif->speedproc = &cs5535_set_drive;
+ hwif->ide_dma_check = &cs5535_dma_check;
+
+ hwif->atapi_dma = 1;
+ hwif->ultra_mask = 0x1F;
+ hwif->mwdma_mask = 0x07;
+
+
+ hwif->udma_four = cs5535_cable_detect(hwif->pci_dev);
+
+ if (!noautodma)
+ hwif->autodma = 1;
+
+ /* just setting autotune and not worrying about bios timings */
+ for (i = 0; i < 2; i++) {
+ hwif->drives[i].autotune = 1;
+ hwif->drives[i].autodma = hwif->autodma;
+ }
+}
+
+static ide_pci_device_t cs5535_chipset __devinitdata = {
+ .name = "CS5535",
+ .init_hwif = init_hwif_cs5535,
+ .channels = 1,
+ .autodma = AUTODMA,
+ .bootable = ON_BOARD,
+};
+
+static int __devinit cs5535_init_one(struct pci_dev *dev,
+ const struct pci_device_id *id)
+{
+ return ide_setup_pci_device(dev, &cs5535_chipset);
+}
+
+static struct pci_device_id cs5535_pci_tbl[] =
+{
+ { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_CS5535_IDE, PCI_ANY_ID,
+ PCI_ANY_ID, 0, 0, 0},
+ { 0, },
+};
+
+MODULE_DEVICE_TABLE(pci, cs5535_pci_tbl);
+
+static struct pci_driver driver = {
+ .name = "CS5535_IDE",
+ .id_table = cs5535_pci_tbl,
+ .probe = cs5535_init_one,
+};
+
+static int __init cs5535_ide_init(void)
+{
+ return ide_pci_register_driver(&driver);
+}
+
+module_init(cs5535_ide_init);
+
+MODULE_AUTHOR("AMD");
+MODULE_DESCRIPTION("PCI driver module for AMD/NS CS5535 IDE");
+MODULE_LICENSE("GPL");
diff --git a/drivers/ide/pci/cy82c693.c b/drivers/ide/pci/cy82c693.c
--- a/drivers/ide/pci/cy82c693.c
+++ b/drivers/ide/pci/cy82c693.c
@@ -469,7 +469,7 @@ static void __devinit init_hwif_cy82c693
static __devinitdata ide_hwif_t *primary;
-void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
+static void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
{
if (PCI_FUNC(hwif->pci_dev->devfn) == 1)
primary = hwif;
diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -701,6 +701,7 @@ static unsigned int setup_mmio_siimage (
unsigned long barsize = pci_resource_len(dev, 5);
u8 tmpbyte = 0;
void __iomem *ioaddr;
+ u32 tmp, irq_mask;
/*
* Drop back to PIO if we can't map the mmio. Some
@@ -726,6 +727,14 @@ static unsigned int setup_mmio_siimage (
pci_set_drvdata(dev, (void *) ioaddr);
if (pdev_is_sata(dev)) {
+ /* make sure IDE0/1 interrupts are not masked */
+ irq_mask = (1 << 22) | (1 << 23);
+ tmp = readl(ioaddr + 0x48);
+ if (tmp & irq_mask) {
+ tmp &= ~irq_mask;
+ writel(tmp, ioaddr + 0x48);
+ readl(ioaddr + 0x48); /* flush */
+ }
writel(0, ioaddr + 0x148);
writel(0, ioaddr + 0x1C8);
}
diff --git a/drivers/scsi/ide-scsi.c b/drivers/scsi/ide-scsi.c
--- a/drivers/scsi/ide-scsi.c
+++ b/drivers/scsi/ide-scsi.c
@@ -395,6 +395,7 @@ static int idescsi_end_request (ide_driv
int log = test_bit(IDESCSI_LOG_CMD, &scsi->log);
struct Scsi_Host *host;
u8 *scsi_buf;
+ int errors = rq->errors;
unsigned long flags;
if (!(rq->flags & (REQ_SPECIAL|REQ_SENSE))) {
@@ -421,11 +422,11 @@ static int idescsi_end_request (ide_driv
printk (KERN_WARNING "ide-scsi: %s: timed out for %lu\n",
drive->name, pc->scsi_cmd->serial_number);
pc->scsi_cmd->result = DID_TIME_OUT << 16;
- } else if (rq->errors >= ERROR_MAX) {
+ } else if (errors >= ERROR_MAX) {
pc->scsi_cmd->result = DID_ERROR << 16;
if (log)
printk ("ide-scsi: %s: I/O error for %lu\n", drive->name, pc->scsi_cmd->serial_number);
- } else if (rq->errors) {
+ } else if (errors) {
if (log)
printk ("ide-scsi: %s: check condition for %lu\n", drive->name, pc->scsi_cmd->serial_number);
if (!idescsi_check_condition(drive, rq))
diff --git a/include/asm-alpha/ide.h b/include/asm-alpha/ide.h
--- a/include/asm-alpha/ide.h
+++ b/include/asm-alpha/ide.h
@@ -15,10 +15,6 @@
#include <linux/config.h>
-#ifndef MAX_HWIFS
-#define MAX_HWIFS CONFIG_IDE_MAX_HWIFS
-#endif
-
#define IDE_ARCH_OBSOLETE_DEFAULTS
static inline int ide_default_irq(unsigned long base)
diff --git a/include/asm-i386/ide.h b/include/asm-i386/ide.h
--- a/include/asm-i386/ide.h
+++ b/include/asm-i386/ide.h
@@ -41,6 +41,12 @@ static __inline__ int ide_default_irq(un
static __inline__ unsigned long ide_default_io_base(int index)
{
+ /*
+ * If PCI is present then it is not safe to poke around
+ * the other legacy IDE ports. Only 0x1f0 and 0x170 are
+ * defined compatibility mode ports for PCI. A user can
+ * override this using ide= but we must default safe.
+ */
if (pci_find_device(PCI_ANY_ID, PCI_ANY_ID, NULL) == NULL) {
switch(index) {
case 2: return 0x1e8;
diff --git a/include/asm-sh/ide.h b/include/asm-sh/ide.h
--- a/include/asm-sh/ide.h
+++ b/include/asm-sh/ide.h
@@ -16,10 +16,6 @@
#include <linux/config.h>
-#ifndef MAX_HWIFS
-#define MAX_HWIFS CONFIG_IDE_MAX_HWIFS
-#endif
-
#define ide_default_io_ctl(base) (0)
#include <asm-generic/ide_iops.h>
diff --git a/include/asm-sh64/ide.h b/include/asm-sh64/ide.h
--- a/include/asm-sh64/ide.h
+++ b/include/asm-sh64/ide.h
@@ -17,10 +17,6 @@
#include <linux/config.h>
-#ifndef MAX_HWIFS
-#define MAX_HWIFS CONFIG_IDE_MAX_HWIFS
-#endif
-
/* Without this, the initialisation of PCI IDE cards end up calling
* ide_init_hwif_ports, which won't work. */
#ifdef CONFIG_BLK_DEV_IDEPCI
diff --git a/include/linux/ide.h b/include/linux/ide.h
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -230,6 +230,7 @@ typedef struct hw_regs_s {
int dma; /* our dma entry */
ide_ack_intr_t *ack_intr; /* acknowledge interrupt */
hwif_chipset_t chipset;
+ struct device *dev;
} hw_regs_t;
/*
@@ -266,6 +267,10 @@ static inline void ide_std_init_ports(hw
#include <asm/ide.h>
+#ifndef MAX_HWIFS
+#define MAX_HWIFS CONFIG_IDE_MAX_HWIFS
+#endif
+
/* needed on alpha, x86/x86_64, ia64, mips, ppc32 and sh */
#ifndef IDE_ARCH_OBSOLETE_DEFAULTS
# define ide_default_io_base(index) (0)
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -387,6 +387,7 @@
#define PCI_DEVICE_ID_NS_SC1100_SMI 0x0511
#define PCI_DEVICE_ID_NS_SC1100_XBUS 0x0515
#define PCI_DEVICE_ID_NS_87410 0xd001
+#define PCI_DEVICE_ID_NS_CS5535_IDE 0x002d
#define PCI_VENDOR_ID_TSENG 0x100c
#define PCI_DEVICE_ID_TSENG_W32P_2 0x3202
@@ -487,6 +488,8 @@
#define PCI_DEVICE_ID_AMD_8151_0 0x7454
#define PCI_DEVICE_ID_AMD_8131_APIC 0x7450
+#define PCI_DEVICE_ID_AMD_CS5536_IDE 0x209A
+
#define PCI_VENDOR_ID_TRIDENT 0x1023
#define PCI_DEVICE_ID_TRIDENT_4DWAVE_DX 0x2000
#define PCI_DEVICE_ID_TRIDENT_4DWAVE_NX 0x2001
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
