Hi All,
Just a quick update re the pci bridge 0000:00:1c.1 problem.
I have tried to 2.6.13.4 without the APCI and Yentra modules. It
boots fine with APCI and Yentra disabled. TPM still not found on
nc8230, but one step closer.
I have now tried up to 2.6.13.4 using the default kernel config and it
still crashes at boot. i.e.
bridge 0000:00:1c.1 then halt.
Linux version 2.6.13.4 ([email protected]) (gcc version 3.3.3
20040412 (Red Hat Linux 3.3.3-7)) #2 Thu Oct 20 07:50:16 BST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
BIOS-e820: 000000001ffd0000 - 000000001ffefc00 (reserved)
BIOS-e820: 000000001ffefc00 - 000000001fffb000 (ACPI NVS)
BIOS-e820: 000000001fffb000 - 0000000020000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed9b000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131024
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126928 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Allocating PCI resources starting at 20000000 (gap: 20000000:c0000000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1729.151 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 515356k/524096k available (1928k kernel code, 8128k reserved,
608k data, 160k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
Calibrating delay using timer specific routine.. 3464.53 BogoMIPS
(lpj=6929079)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000
00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000
00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040
00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like
an initrd
Freeing initrd memory: 197k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0322, last bus=32
PCI: Using configuration type 1
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Using IRQ router PIIX/ICH [8086/2641] at 0000:00:1f.0
PCI: IRQ 0 for device 0000:00:01.0 doesn't match PIRQ mask - try
pci=usepirqmask
PCI: Found IRQ 10 for device 0000:00:01.0
PCI: Sharing IRQ 10 with 0000:00:1c.0
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:01:00.0
PCI: Sharing IRQ 10 with 0000:10:00.0
PCI: IRQ 0 for device 0000:00:1c.1 doesn't match PIRQ mask - try
pci=usepirqmask
PCI: Found IRQ 11 for device 0000:00:1c.1
PCI: Sharing IRQ 11 with 0000:00:1d.1
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1
PCI: Bridge: 0000:00:01.0
IO window: 2000-2fff
MEM window: c8800000-c8bfffff
PREFETCH window: c0000000-c7ffffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: c8000000-c83fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00004000-00004fff
IO window: 00005000-00005fff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 4000-5fff
MEM window: c8400000-c87fffff
PREFETCH window: 20000000-21ffffff
PCI: Found IRQ 10 for device 0000:00:01.0
PCI: Sharing IRQ 10 with 0000:00:1c.0
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:01:00.0
PCI: Sharing IRQ 10 with 0000:10:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Found IRQ 10 for device 0000:00:1c.0
PCI: Sharing IRQ 10 with 0000:00:01.0
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:01:00.0
PCI: Sharing IRQ 10 with 0000:10:00.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Device 0000:00:1c.1 not available because of resource collisions
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Found IRQ 11 for device 0000:02:06.0
PCI: Sharing IRQ 11 with 0000:00:1d.2
PCI: Sharing IRQ 11 with 0000:02:06.5
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1129795129.180:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
PCI: Found IRQ 10 for device 0000:00:01.0
PCI: Sharing IRQ 10 with 0000:00:1c.0
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:01:00.0
PCI: Sharing IRQ 10 with 0000:10:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
PCI: Found IRQ 10 for device 0000:00:1c.0
PCI: Sharing IRQ 10 with 0000:00:01.0
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:01:00.0
PCI: Sharing IRQ 10 with 0000:10:00.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
PCI: Device 0000:00:1c.1 not available because of resource collisions
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
[drm] Initialized drm 1.0.0 20040925
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
PCI: Found IRQ 10 for device 0000:00:1e.3
PCI: Sharing IRQ 10 with 0000:02:06.2
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
PCI: Found IRQ 10 for device 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:00:01.0
PCI: Sharing IRQ 10 with 0000:00:1c.0
PCI: Sharing IRQ 10 with 0000:01:00.0
PCI: Sharing IRQ 10 with 0000:10:00.0
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x3580-0x3587, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: HTS541040G9AT00, ATA DISK drive
hdb: UJDA765aDVD/CDRW, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/7539KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbmon: debugfs is not available
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 160k freed
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps:
0xa44793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
PCI: Found IRQ 10 for device 0000:00:1d.7
PCI: Sharing IRQ 10 with 0000:00:1d.0
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 10, io mem 0xc8c00000
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 10 for device 0000:00:1d.0
PCI: Sharing IRQ 10 with 0000:00:1d.7
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 10, io base 0x00003000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:1d.1
PCI: Sharing IRQ 11 with 0000:00:1c.1
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00003020
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:1d.2
PCI: Sharing IRQ 11 with 0000:02:06.0
PCI: Sharing IRQ 11 with 0000:02:06.5
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00003040
usb 1-2: new high speed USB device using ehci_hcd and address 2
input: PS/2 Generic Mouse on synaptics-pt/serio0
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
EXT3 FS on hda2, internal journal
device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
[email protected]
cdrom: open failed.
Adding 1024120k swap on /dev/hda3. Priority:-1 extents:1
IA-32 Microcode Update Driver: v1.14 <[email protected]>
microcode: No new microcode data for CPU0
Vendor: Lexar Model: JumpDrive I.D. Rev: 1000
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
SCSI device sda: 502784 512-byte hdwr sectors (257 MB)
sda: Write Protect is off
sda: Mode Sense: 43 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 502784 512-byte hdwr sectors (257 MB)
sda: Write Protect is off
sda: Mode Sense: 43 00 00 00
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
tg3.c:v3.37 (August 25, 2005)
PCI: Found IRQ 10 for device 0000:10:00.0
PCI: Sharing IRQ 10 with 0000:00:01.0
PCI: Sharing IRQ 10 with 0000:00:1c.0
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:01:00.0
PCI: Setting latency timer of device 0000:10:00.0 to 64
eth0: Tigon3 [partno(BCM95751M) rev 4101 PHY(5750)]
(PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:12:79:c2:9c:36
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1]
TSOcap[1]
eth0: dma_rwctrl[76180000]
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4094 buckets, 32752 max) - 212 bytes per
conntrack
lp: driver loaded but no devices found
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03432c0(lo)
IPv6 over IPv4 tunneling driver
usb 1-2: USB disconnect, address 2
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
usb 2-1: new full speed USB device using uhci_hcd and address 2
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
Vendor: Wincan Model: HARD DRIVE DISK Rev: 1.04
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 128000 512-byte hdwr sectors (66 MB)
sda: Write Protect is off
sda: Mode Sense: 43 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 128000 512-byte hdwr sectors (66 MB)
sda: Write Protect is off
sda: Mode Sense: 43 00 00 00
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete
tpm_infineon: No Infineon TPM found! Sorry!
tpm_infineon: unable to pci_register_driver minor 224
tpm_infineon: No Infineon TPM found! Sorry!
tpm_infineon: unable to pci_register_driver minor 224
I'd solve this problem but my Linux kernel coding skills are aren't
yet up to the challenge, give me a parallel port problem anyday
(especially a simple one).
Thanks
Chris R www.hackinghardware.com
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
