1. Summary: Kernel crash after load usb-ohci module.
2. Description: I have Slackware 10.2 standart kernel (bare.i). After adding kernel module usb-uhci (modprobe usb-ohci) I get kernel crash:
"kernel BUG at usb-ohci.h:464!"
3. Keywords: module usb-ohci
4. Kernel version: Linux version 2.4.31 (root@tree) (gcc version 3.3.5) #6 Sun Jun 5 19:04:47 PDT 2005
5. Output of Oops.. message:
ksymoops 2.4.9 on i586 2.4.31. Options used
-V (default)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.4.31/ (default)
-m /boot/System.map (specified)
kernel BUG at usb-ohci.h:464!
invalid operand: 0000
CPU: 0
EIP: 0010:[<c2a2d300>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010246
eax: 00000000 ebx: c2a35000 ecx: c18be800 edx: 000015a0
esi: 00000000 edi: c0365e94 ebp: 00000002 esp: c0365e24
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 0, stackpage=c0365000)
Stack: 00000000 c2a35000 c18be800 c0365e94 00000002 c2a2e6fe c18be800 c095c560
04000001 c0365e94 00000009 c0109fbd 00000009 c18be800 c0365e94 c0384990
00000009 c095c560 c0365e94 c010a138 00000009 c0365e94 c095c560 c10b2b10
Call Trace: [<c2a2e6fe>] [<c0109fbd>] [<c010a138>] [<c010c428>] [<c020841d>]
[<c0208a28>] [<c0210060>] [<c0109fbd>] [<c010a138>] [<c010c428>] [<c011b6c0>]
[<c010a16d>] [<c0106f50>] [<c010c428>] [<c0106f50>] [<c0106f73>] [<c0107012>]
[<c0105000>]
Code: 0f 0b d0 01 c4 f1 a2 c2 e9 5b ff ff ff 8d 76 00 55 57 56 53
EIP; c2a2d300 <END_OF_CODE+55759/????> <=====
ecx; c18be800 <_end+14fda34/25d8294>
edi; c0365e94 <init_task_union+1e94/2000>
esp; c0365e24 <init_task_union+1e24/2000>
Trace; c2a2e6fe <END_OF_CODE+56b57/????>
Trace; c0109fbd <handle_IRQ_event+3d/70>
Trace; c010a138 <do_IRQ+68/a0>
Trace; c010c428 <call_do_IRQ+5/d>
Trace; c020841d <ide_do_request+1ad/320>
Trace; c0208a28 <ide_intr+d8/120>
Trace; c0210060 <read_intr+0/120>
Trace; c0109fbd <handle_IRQ_event+3d/70>
Trace; c010a138 <do_IRQ+68/a0>
Trace; c010c428 <call_do_IRQ+5/d>
Trace; c011b6c0 <do_softirq+40/a0>
Trace; c010a16d <do_IRQ+9d/a0>
Trace; c0106f50 <default_idle+0/50>
Trace; c010c428 <call_do_IRQ+5/d>
Trace; c0106f50 <default_idle+0/50>
Trace; c0106f73 <default_idle+23/50>
Trace; c0107012 <cpu_idle+52/70>
Trace; c0105000 <_stext+0/0>
Code; c2a2d300 <END_OF_CODE+55759/????>
00000000 <_EIP>:
Code; c2a2d300 <END_OF_CODE+55759/????> <=====
0: 0f 0b ud2a <=====
Code; c2a2d302 <END_OF_CODE+5575b/????>
2: d0 01 rolb (%ecx)
Code; c2a2d304 <END_OF_CODE+5575d/????>
4: c4 les (bad),%esi
Code; c2a2d305 <END_OF_CODE+5575e/????>
5: f1 icebp
Code; c2a2d306 <END_OF_CODE+5575f/????>
6: a2 c2 e9 5b ff mov %al,0xff5be9c2
Code; c2a2d30b <END_OF_CODE+55764/????>
b: ff (bad)
Code; c2a2d30c <END_OF_CODE+55765/????>
c: ff 8d 76 00 55 57 decl 0x57550076(%ebp)
Code; c2a2d312 <END_OF_CODE+5576b/????>
12: 56 push %esi
Code; c2a2d313 <END_OF_CODE+5576c/????>
13: 53 push %ebx
<0>Kernel panic: Aiee, killing interrupt handler!
7. Environment
7.1. Software
Linux sjbrover 2.4.31 #6 Sun Jun 5 19:04:47 PDT 2005 i586 unknown unknown GNU/Linux
Gnu C 3.3.6
Gnu make 3.80
util-linux 2.12p
mount 2.12p
modutils 2.4.27
e2fsprogs 1.38
pcmcia-cs 3.2.8
quota-tools 3.12.
PPP 2.4.4b1
Linux C Library 2.3.5
Dynamic linker (ldd) 2.3.5
Linux C++ Library 5.0.7
Procps 3.2.5
Net-tools 1.60
Kbd 1.12
Sh-utils 5.2.1
Modules Loaded usb-ohci usbcore serial_cs pcnet_cs 8390 crc32 ds yenta_socket pcmcia_core ide-scsi
7.2. Processor:
processor : 0
vendor_id : GenuineIntel
cpu family : 5
model : 4
model name : Pentium MMX
stepping : 3
cpu MHz : 233.322
fdiv_bug : no
hlt_bug : no
f00f_bug : yes
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr mce cx8 mmx
bogomips : 465.30
7.3. Module information
usb-ohci 19368 0 (unused)
usbcore 59116 0 [usb-ohci]
serial_cs 4532 0 (unused)
pcnet_cs 11260 1
8390 5776 0 [pcnet_cs]
crc32 2880 0 [8390]
ds 6548 3 [serial_cs pcnet_cs]
yenta_socket 10436 3
pcmcia_core 39140 0 [serial_cs pcnet_cs ds yenta_socket]
ide-scsi 9392 0
7.4. Loaded driver and hardware information
root@sjbrover:~# cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : pcnet_cs
0300-031f : pcnet_cs
0376-0376 : ide1
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
4000-40ff : PCI CardBus #01
4400-44ff : PCI CardBus #01
4800-48ff : PCI CardBus #09
4c00-4cff : PCI CardBus #09
5000-50ff : PCI CardBus #05
5400-54ff : PCI CardBus #05
ec80-ecff : ALi Corporation M3307
ffa0-ffaf : OPTi Inc. 82C825 [Firebridge 2]
root@sjbrover:~# cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-01ffffff : System RAM
00100000-002ca1ee : Kernel code
002ca1ef-003620c3 : Kernel data
0e000000-0effffff : Chips and Technologies F65554
0e000000-0e17ffff : vesafb
10000000-10000fff : OPTi Inc. 82C814 [Firebridge 1]
10001000-10001fff : Texas Instruments PCI1131
10002000-10002fff : Texas Instruments PCI1131 (#2)
10400000-107fffff : PCI CardBus #01
10800000-10bfffff : PCI CardBus #01
10c00000-10ffffff : PCI CardBus #09
11000000-113fffff : PCI CardBus #09
11400000-117fffff : PCI CardBus #05
11800000-11bfffff : PCI CardBus #05
a0000000-a0000fff : card services
febfe000-febfefff : CMD Technology Inc USB0670
febff000-febfffff : ALi Corporation M3307
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
fffe0000-ffffffff : reserved
7.5. PCI information
00:00.0 Host bridge: OPTi Inc. 82C701 [FireStar Plus] (rev 20)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR- <PERR-
Latency: 0
00:01.0 ISA bridge: OPTi Inc. 82C700 [FireStar] (rev 20)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:04.0 CardBus bridge: OPTi Inc. 82C814 [Firebridge 1]
Subsystem: Unknown device 8040:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 0
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
00:05.0 USB Controller: Silicon Image, Inc. USB0670 (rev 04) (prog-if 10 [OHCI])
Subsystem: Silicon Image, Inc. USB0670
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
00:06.0 VGA compatible controller: Chips and Technologies F65554 (rev c2) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at 0e000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at 21800000 [disabled] [size=256K]
00:07.0 CardBus bridge: Texas Instruments PCI1131 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 04
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 11400000-117ff000 (prefetchable)
Memory window 1: 11800000-11bff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:07.1 CardBus bridge: Texas Instruments PCI1131 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 04
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 10002000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=09, subordinate=0c, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:08.0 Multimedia video controller: ALi Corporation M3307
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 500ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ec80 [size=128]
00:14.0 IDE interface: OPTi Inc. 82C825 [Firebridge 2] (rev 12) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at ffa0 [size=16]
root@sjbrover:~# cat /proc/interrupts
CPU0
0: 544483 XT-PIC timer
1: 2456 XT-PIC keyboard
2: 0 XT-PIC cascade
3: 28346 XT-PIC pcnet_cs
4: 600 XT-PIC serial
8: 1 XT-PIC rtc
9: 0 XT-PIC usb-ohci
11: 0 XT-PIC Texas Instruments PCI1131 (#2), Texas Instruments PCI1131
12: 0 XT-PIC PS/2 Mouse
14: 6327 XT-PIC ide0
15: 3 XT-PIC ide1
NMI: 0
ERR: 0
7.6. SCSI information
Attached devices: none
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
