Various small mods for the Altix ioc4 serial driver - mostly cleanup:
- remove UIF_INITIALIZED usage
- use the 'lock' from uart_port
- better multiple card support
Signed-off-by: Patrick Gefre <[email protected]>
---
diffstat
ioc4_serial.c | 80 +++++++++++++++++++++++++++++++---------------------------
1 files changed, 44 insertions(+), 36 deletions(-)
Index: linux/drivers/serial/ioc4_serial.c
===================================================================
--- linux.orig/drivers/serial/ioc4_serial.c 2005-09-13 04:01:54.000000000 -0500
+++ linux/drivers/serial/ioc4_serial.c 2005-10-04 11:27:42.894430606 -0500
@@ -308,6 +308,8 @@
typedef void ioc4_intr_func_f(void *, uint32_t);
typedef ioc4_intr_func_f *ioc4_intr_func_t;
+static unsigned int Num_of_ioc4_cards;
+
/* defining this will get you LOTS of great debug info */
//#define DEBUG_INTERRUPTS
#define DPRINT_CONFIG(_x...) ;
@@ -317,7 +319,8 @@
#define WAKEUP_CHARS 256
/* number of characters we want to transmit to the lower level at a time */
-#define IOC4_MAX_CHARS 128
+#define IOC4_MAX_CHARS 256
+#define IOC4_FIFO_CHARS 255
/* Device name we're using */
#define DEVICE_NAME "ttyIOC"
@@ -1050,6 +1053,7 @@
return -ENOMEM;
}
memset(port, 0, sizeof(struct ioc4_port));
+ spin_lock_init(&port->ip_lock);
/* we need to remember the previous ones, to point back to
* them farther down - setting up the ring buffers.
@@ -1703,12 +1707,14 @@
baud = 9600;
if (!the_port->fifosize)
- the_port->fifosize = IOC4_MAX_CHARS;
+ the_port->fifosize = IOC4_FIFO_CHARS;
the_port->timeout = ((the_port->fifosize * HZ * bits) / (baud / 10));
the_port->timeout += HZ / 50; /* Add .02 seconds of slop */
the_port->ignore_status_mask = N_ALL_INPUT;
+ info->tty->low_latency = 1;
+
if (I_IGNPAR(info->tty))
the_port->ignore_status_mask &= ~(N_PARITY_ERROR
| N_FRAMING_ERROR);
@@ -1754,7 +1760,6 @@
*/
static inline int ic4_startup_local(struct uart_port *the_port)
{
- int retval = 0;
struct ioc4_port *port;
struct uart_info *info;
@@ -1766,9 +1771,6 @@
return -1;
info = the_port->info;
- if (info->flags & UIF_INITIALIZED) {
- return retval;
- }
if (info->tty) {
set_bit(TTY_IO_ERROR, &info->tty->flags);
@@ -1787,7 +1789,6 @@
/* set the speed of the serial port */
ioc4_change_speed(the_port, info->tty->termios, (struct termios *)0);
- info->flags |= UIF_INITIALIZED;
return 0;
}
@@ -1797,9 +1798,13 @@
*/
static void ioc4_cb_output_lowat(struct ioc4_port *port)
{
+ unsigned long pflags;
+
/* ip_lock is set on the call here */
if (port->ip_port) {
+ spin_lock_irqsave(&port->ip_port->lock, pflags);
transmit_chars(port->ip_port);
+ spin_unlock_irqrestore(&port->ip_port->lock, pflags);
}
}
@@ -2076,8 +2081,7 @@
* available data as long as it returns some.
*/
/* Re-arm the timer */
- writel(port->ip_rx_cons | IOC4_SRCIR_ARM,
- &port->ip_serial_regs->srcir);
+ writel(port->ip_rx_cons | IOC4_SRCIR_ARM, &port->ip_serial_regs->srcir);
prod_ptr = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
cons_ptr = port->ip_rx_cons;
@@ -2311,6 +2315,7 @@
}
return total;
}
+
/**
* receive_chars - upper level read. Called with ip_lock.
* @the_port: port to read from
@@ -2319,9 +2324,11 @@
{
struct tty_struct *tty;
unsigned char ch[IOC4_MAX_CHARS];
- int read_count, request_count;
+ int read_count, request_count = IOC4_MAX_CHARS;
struct uart_icount *icount;
struct uart_info *info = the_port->info;
+ int flip = 0;
+ unsigned long pflags;
/* Make sure all the pointers are "good" ones */
if (!info)
@@ -2329,16 +2336,17 @@
if (!info->tty)
return;
+ spin_lock_irqsave(&the_port->lock, pflags);
tty = info->tty;
- request_count = TTY_FLIPBUF_SIZE - tty->flip.count - 1;
+ if (request_count > TTY_FLIPBUF_SIZE - tty->flip.count)
+ request_count = TTY_FLIPBUF_SIZE - tty->flip.count;
if (request_count > 0) {
- if (request_count > IOC4_MAX_CHARS - 2)
- request_count = IOC4_MAX_CHARS - 2;
icount = &the_port->icount;
read_count = do_read(the_port, ch, request_count);
if (read_count > 0) {
+ flip = 1;
memcpy(tty->flip.char_buf_ptr, ch, read_count);
memset(tty->flip.flag_buf_ptr, TTY_NORMAL, read_count);
tty->flip.char_buf_ptr += read_count;
@@ -2347,7 +2355,11 @@
icount->rx += read_count;
}
}
- tty_flip_buffer_push(tty);
+
+ spin_unlock_irqrestore(&the_port->lock, pflags);
+
+ if (flip)
+ tty_flip_buffer_push(tty);
}
/**
@@ -2405,18 +2417,14 @@
info = the_port->info;
- if (!(info->flags & UIF_INITIALIZED))
- return;
-
wake_up_interruptible(&info->delta_msr_wait);
if (info->tty)
set_bit(TTY_IO_ERROR, &info->tty->flags);
- spin_lock_irqsave(&port->ip_lock, port_flags);
+ spin_lock_irqsave(&the_port->lock, port_flags);
set_notification(port, N_ALL, 0);
- info->flags &= ~UIF_INITIALIZED;
- spin_unlock_irqrestore(&port->ip_lock, port_flags);
+ spin_unlock_irqrestore(&the_port->lock, port_flags);
}
/**
@@ -2475,12 +2483,10 @@
static void ic4_start_tx(struct uart_port *the_port)
{
struct ioc4_port *port = get_ioc4_port(the_port);
- unsigned long flags;
if (port) {
- spin_lock_irqsave(&port->ip_lock, flags);
- transmit_chars(the_port);
- spin_unlock_irqrestore(&port->ip_lock, flags);
+ set_notification(port, N_OUTPUT_LOWAT, 1);
+ enable_intrs(port, port->ip_hooks->intr_tx_mt);
}
}
@@ -2522,9 +2528,9 @@
}
/* Start up the serial port */
- spin_lock_irqsave(&port->ip_lock, port_flags);
+ spin_lock_irqsave(&the_port->lock, port_flags);
retval = ic4_startup_local(the_port);
- spin_unlock_irqrestore(&port->ip_lock, port_flags);
+ spin_unlock_irqrestore(&the_port->lock, port_flags);
return retval;
}
@@ -2539,12 +2545,11 @@
ic4_set_termios(struct uart_port *the_port,
struct termios *termios, struct termios *old_termios)
{
- struct ioc4_port *port = get_ioc4_port(the_port);
unsigned long port_flags;
- spin_lock_irqsave(&port->ip_lock, port_flags);
+ spin_lock_irqsave(&the_port->lock, port_flags);
ioc4_change_speed(the_port, termios, old_termios);
- spin_unlock_irqrestore(&port->ip_lock, port_flags);
+ spin_unlock_irqrestore(&the_port->lock, port_flags);
}
/**
@@ -2619,24 +2624,25 @@
__FUNCTION__, (void *)the_port,
(void *)port));
- spin_lock_init(&the_port->lock);
/* membase, iobase and mapbase just need to be non-0 */
the_port->membase = (unsigned char __iomem *)1;
- the_port->line = the_port->iobase = ii;
+ the_port->iobase = (pdev->bus->number << 16) | ii;
+ the_port->line = (Num_of_ioc4_cards << 2) | ii;
the_port->mapbase = 1;
the_port->type = PORT_16550A;
- the_port->fifosize = IOC4_MAX_CHARS;
+ the_port->fifosize = IOC4_FIFO_CHARS;
the_port->ops = &ioc4_ops;
the_port->irq = control->ic_irq;
the_port->dev = &pdev->dev;
+ spin_lock_init(&the_port->lock);
if (uart_add_one_port(&ioc4_uart, the_port) < 0) {
printk(KERN_WARNING
- "%s: unable to add port %d\n",
- __FUNCTION__, the_port->line);
+ "%s: unable to add port %d bus %d\n",
+ __FUNCTION__, the_port->line, pdev->bus->number);
} else {
DPRINT_CONFIG(
- ("IOC4 serial driver port %d irq = %d\n",
- the_port->line, the_port->irq));
+ ("IOC4 serial port %d irq = %d, bus %d\n",
+ the_port->line, the_port->irq, pdev->bus->number));
}
/* all ports are rs232 for now */
ioc4_set_proto(port, PROTO_RS232);
@@ -2746,6 +2752,8 @@
if ((ret = ioc4_serial_core_attach(idd->idd_pdev)))
goto out4;
+ Num_of_ioc4_cards++;
+
return ret;
/* error exits that give back resources */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
