Guennadi Liakhovetski <[email protected]> writes:
> Just tried pktcdvd on 2.6.13.1. The setup went fine:
>
> 20:33:13: pktcdvd: writer pktcdvd0 mapped to hdc
> 20:33:21: pktcdvd: inserted media is CD-RW
> 20:33:21: pktcdvd: Fixed packets, 32 blocks, Mode-2 disc
> 20:33:21: pktcdvd: Max. media speed: 10
> 20:33:21: pktcdvd: write speed 10x
> 20:33:21: pktcdvd: 590528kB available on disc
> 20:33:23: UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'LinuxUDF', timestamp 2005/09/24 20:18 (1078)
>
> But, as I tried to copy some files to the CD-RW, it first went ok, but
> then produced the following:
>
> 20:41:01: ide-cd: cmd 0x2a timed out
> ^^^^ ---------> write10
> 20:41:01: hdc: DMA timeout retry
> 20:41:01: hdc: timeout waiting for DMA
> 20:41:01: hdc: status timeout: status=0xd0 { Busy }
> 20:41:01: ide: failed opcode was: unknown
> 20:41:01: hdc: drive not ready for command
> 20:41:31: hdc: ATAPI reset timed-out, status=0x80
> 20:42:06: ide1: reset timed-out, status=0x80
> 20:42:06: hdc: status timeout: status=0x80 { Busy }
> 20:42:06: ide: failed opcode was: unknown
> 20:42:06: hdc: drive not ready for command
> 20:42:36: hdc: ATAPI reset timed-out, status=0x80
> 20:43:07: : I/O error, dev hdc, sector 136672
> 20:43:07: end_request: I/O error, dev hdc, sector 136680
> 20:43:07: end_request: I/O error, dev hdc, sector 136688
> 20:43:07: end_request: I/O error, dev hdc, sector 136696
> 20:43:07: end_request: I/O error, dev hdc, sector 137216
> 20:43:07: end_request: I/O error, dev hdc, sector 137224
> 20:43:07: end_request: I/O error, dev hdc, sector 137232
> 20:43:07: end_request: I/O error, dev hdc, sector 137240
> ... <thousands of the above>
> 20:43:11: end_request: I/O error, dev hdc, sector 344440
> 20:43:11: end_request: I/O error, dev hdc, sector 344444
> 20:43:11: pktcdvd: bb 00 06 ea 06 ea 00 00 00 00 00 00 - sense 00.e0.0e (No sense)
> 20:43:11: end_request: I/O error, dev hdc, sector 363008
> 20:43:11: end_request: I/O error, dev hdc, sector 363016
> ... <more of them>
> 20:43:11: printk: 79693 messages suppressed.
> 20:43:11: Buffer I/O error on device pktcdvd0, logical block 90752
> 20:43:11: lost page write due to I/O error on pktcdvd0
> 20:43:11: end_request: I/O error, dev hdc, sector 362880
> 20:43:11: end_request: I/O error, dev hdc, sector 362884
> ...
>
> the "cp" finished earlier, I did a sync, and it also finished. The good
> parts - no Oops, no process stuck in "D", tha bad parts - it didn't
> work:-), the IDE LED stays on and I cannot eject the CD. The CD-R is a
> BenQ 52x32x52 Seamless Link alone on ide1, the disk does indeed say
> 4x-10x. The cd-writer works mostly... if I am gentle to it - I usually
> burn at 32x even if the media says 52x... Is it just a hw-failure or a
> driver bug?
Did it ever work with this hardware, for example using 2.6.12? Does
the drive have the latest firmware? If not, a firmware upgrade might
help. Does it work if you use ide-scsi instead of ide-cd?
What errors do you get if you try to burn at 52x without using the
packet writing driver?
--
Peter Osterlund - [email protected]
http://web.telia.com/~u89404340
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
|
|