>> If i use the irqpoll boot option, then it is fine, it boots with no
>> errors
>> at all, and i can even mount a filesystem on that PATA hd.
>>
>
> Good. Now can you please generate the output from `dmesg -s 1000000' for
> both good and bad kernels, then do
>
> diff -u dmesg.good dmesg.bad
>
> and send the result? Make sure to identify both kernel versions.
>
> Thanks.
No need to CC me anymore, i subscribed, thanks.
Assuming bad is 2.6.13.1 with irqpoll, and good is 2.6.12.6 without irqpoll
Here is the unified diff:
--- dmesg.good 2005-09-14 18:05:06.000000000 -0300
+++ dmesg.bad 2005-09-14 18:04:28.000000000 -0300
@@ -15,19 +15,30 @@
pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
pnp: 00:01: ioport range 0x5000-0x503f has been reserved
pnp: 00:01: ioport range 0x5100-0x513f has been reserved
+PCI: Bridge: 0000:00:08.0
+ IO window: 9000-afff
+ MEM window: dc000000-dfffffff
+ PREFETCH window: d0000000-d7ffffff
+PCI: Bridge: 0000:00:1e.0
+ IO window: disabled.
+ MEM window: da000000-dbffffff
+ PREFETCH window: c0000000-cfffffff
+PCI: Setting latency timer of device 0000:00:08.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
-audit(1126731608.537:0): initialized
+audit(1126731295.846:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 [email protected]).
-NTFS driver 2.1.22 [Flags: R/W].
+NTFS driver 2.1.23 [Flags: R/W].
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
fakephp: Fake PCI Hot Plug Controller Driver
ACPI: Power Button (FF) [PWRF]
+ACPI: Power Button (CM) [PWRB]
ACPI: Fan [FAN] (on)
-ACPI: Thermal Zone [THRM] (44 C)
+ACPI: CPU0 (power states: C1[C1])
+ACPI: Thermal Zone [THRM] (45 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
@@ -38,7 +49,7 @@
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
-Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
+Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
@@ -46,7 +57,7 @@
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [LNK2] -> GSI 10 (level, low)
-> IRQ 10
-ttyS4 at I/O 0x9800 (irq = 10) is a 16550A
+ttyS2 at I/O 0x9800 (irq = 10) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
@@ -54,7 +65,8 @@
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe ([email protected]) and [email protected]
-forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.32.
+forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.35.
+acpi_bus-0212 [01] acpi_bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LMAC] -> GSI 10 (level, low)
-> IRQ 10
PCI: Setting latency timer of device 0000:00:04.0 to 64
@@ -67,6 +79,7 @@
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
+acpi_bus-0212 [01] acpi_bus_set_power : Device is not power manageable
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
@@ -81,7 +94,7 @@
hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdc: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
-libata version 1.11 loaded.
+libata version 1.12 loaded.
sata_sil version 0.9
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
@@ -93,9 +106,36 @@
ata1(0): applying Seagate errata fix
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
-spurious 8259A interrupt: IRQ7.
+irq 11: nobody cared (try booting with the "irqpoll" option)
+ [<c01421fa>] __report_bad_irq+0x2a/0x90
+ [<c0142320>] note_interrupt+0xa0/0x100
+ [<c0141b28>] __do_IRQ+0x128/0x140
+ [<c010506e>] do_IRQ+0x3e/0x60
+ =======================
+ [<c01034b2>] common_interrupt+0x1a/0x20
+ [<c0122950>] __do_softirq+0x30/0x90
+ [<c0105181>] do_softirq+0x41/0x50
+ =======================
+ [<c0122a65>] irq_exit+0x35/0x40
+ [<c0105075>] do_IRQ+0x45/0x60
+ [<c01034b2>] common_interrupt+0x1a/0x20
+ [<c010f544>] delay_tsc+0x14/0x20
+ [<c039fa6f>] ata_pio_complete+0x15f/0x220
+ [<c03a02c0>] ata_pio_task+0x50/0x80
+ [<c012e2a0>] worker_thread+0x200/0x2f0
+ [<c03a0270>] ata_pio_task+0x0/0x80
+ [<c0119960>] default_wake_function+0x0/0x20
+ [<c0119960>] default_wake_function+0x0/0x20
+ [<c012e0a0>] worker_thread+0x0/0x2f0
+ [<c0132948>] kthread+0xa8/0xe0
+ [<c01328a0>] kthread+0x0/0xe0
+ [<c0101395>] kernel_thread_helper+0x5/0x10
+handlers:
+[<c03a0cc0>] (ata_interrupt+0x0/0x120)
+Disabling IRQ #11
ata2: dev 0 cfg 49:2f00 82:346b 83:4b09 84:4003 85:3469 86:0a09 87:4003
88:203f
ata2: dev 0 ATA, max UDMA/100, 39102336 sectors:
+ata2(0): applying bridge limits
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
Vendor: ATA Model: ST3120026AS Rev: 3.18
@@ -116,7 +156,8 @@
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
-usbmon: debugs is not available
+usbmon: debugfs is not available
+acpi_bus-0212 [01] acpi_bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUB2] -> GSI 11 (level, low)
-> IRQ 11
PCI: Setting latency timer of device 0000:00:02.2 to 64
@@ -135,7 +176,8 @@
ehci_hcd 0000:01:08.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
-ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
+ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
+acpi_bus-0212 [01] acpi_bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUBA] -> GSI 12 (level, low)
-> IRQ 12
@@ -145,6 +187,7 @@
ohci_hcd 0000:00:02.0: irq 12, io mem 0xe0087000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
+acpi_bus-0212 [01] acpi_bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUBB] -> GSI 10 (level, low)
-> IRQ 10
PCI: Setting latency timer of device 0000:00:02.1 to 64
@@ -153,7 +196,7 @@
ohci_hcd 0000:00:02.1: irq 10, io mem 0xe0082000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
-USB Universal Host Controller Interface driver v2.2
+USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNK1] -> GSI 5 (level, low)
-> IRQ 5
@@ -171,32 +214,34 @@
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
-usbcore: registered new driver usb-storage
-USB Mass Storage support registered.
usb 3-1: new low speed USB device using ohci_hcd and address 2
usb 3-2: new low speed USB device using ohci_hcd and address 3
+usbcore: registered new driver usb-storage
+USB Mass Storage support registered.
input: USB HID v1.00 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:02.0-1
input: USB HID v1.00 Device [NOVATEK USB Keyboard] on usb-0000:00:02.0-1
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with
IntelliEye(TM)] on usb-0000:00:02.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
-I2O subsystem v$Rev$
+I2O subsystem v1.288
i2o: max drivers = 8
-I2O Configuration OSM v$Rev$
-I2O Block Device OSM v$Rev$
-I2O SCSI Peripheral OSM v$Rev$
-I2O ProcFS OSM v$Rev$
+I2O Configuration OSM v1.248
+I2O Bus Adapter OSM v$Rev$
+I2O Block Device OSM v1.287
+I2O SCSI Peripheral OSM v1.282
+I2O ProcFS OSM v1.145
i2c /dev entries driver
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-2: nForce2 SMBus adapter at 0x5100
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected]
-Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24
10:33:39 2005 UTC).
+Advanced Linux Sound Architecture Driver Version 1.0.9b (Thu Jul 28
12:20:13 2005 UTC).
+acpi_bus-0212 [01] acpi_bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LACI] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:06.0 to 64
-intel8x0_measure_ac97_clock: measured 49759 usecs
-intel8x0: clocking to 47452
+intel8x0_measure_ac97_clock: measured 50339 usecs
+intel8x0: clocking to 47378
ALSA device list:
#0: NVidia nForce2 with ALC650F at 0xe0080000, irq 5
oprofile: using timer interrupt.
@@ -205,18 +250,21 @@
u32 classifier
Actions configured
NET: Registered protocol family 2
-IP: routing cache hash table of 8192 buckets, 64Kbytes
+IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
+TCP reno registered
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 248 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <[email protected]>.
http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
+TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
+Using IPI Shortcut mode
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
@@ -226,18 +274,21 @@
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
-Freeing unused kernel memory: 204k freed
+Freeing unused kernel memory: 200k freed
eql: remember to turn off Van-Jacobson compression on your slave devices.
Linux video capture interface: v1.00
-cx2388x v4l2 driver version 0.0.4 loaded
+cx2388x v4l2 driver version 0.0.5 loaded
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 12
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNK4] -> GSI 12 (level, low)
-> IRQ 12
cx88[0]: subsystem: 0000:0000, board: Prolink PlayTV PVR [card=11,insmod
option]
+TV tuner 43 at 0x1fe, Radio tuner -1 at 0x1fe
tveeprom(cx88xx internal): Huh, no eeprom present (err=-121)?
cx88[0]/0: found at 0000:01:07.0, rev: 3, irq: 12, latency: 32, mmio:
0xdc000000
-tuner 3-0060: chip found @ 0xc0 (cx88[0])
+ : chip found @ 0xc0 (cx88[0])
+ : All bytes are equal. It is not a TEA5767
tuner 3-0060: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F))
tda9885/6/7: chip found @ 0x86
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
+hdc: cdrom_pc_intr: The drive appears confused (ireason = 0x01)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
| |
 |