> > >40k isn't large - please include such patches in the email.
> > >
> > Thank you, Andrew, for your reply and hints, you sent.
> Did everything get addressed?
Maybe not, if you still want it in e-mail as plaintext, grr.
> Then send the patch, cc'ed to the mailing list as per
> http://www.zip.com.au/~akpm/linux/patches/stuff/tpp.txt, thanks.
Oops, I read only SubmittingPatches. So this file should be changed in point 7
(that not everybody wants URLs).
This patch removes old api in pci probing and replaces it with new. Firmware
loading added.
Generated in 2.6.13-mm2 kernel version.
Signed-off-by: Jiri Slaby <[email protected]>
---
drivers/char/isicom.c | 2009 ++++++++++++++++++++++++-------------------------
include/linux/isicom.h | 53 -
2 files changed, 1006 insertions(+), 1056 deletions(-)
diff --git a/drivers/char/isicom.c b/drivers/char/isicom.c
--- a/drivers/char/isicom.c
+++ b/drivers/char/isicom.c
@@ -20,7 +20,7 @@
* 3/9/99 sameer Added support for ISI4616 cards.
*
* 16/9/99 sameer We do not force RTS low anymore.
- * This is to prevent the firmware
+ * This is to prevent the firmware
* from getting confused.
*
* 26/10/99 sameer Cosmetic changes:The driver now
@@ -31,28 +31,28 @@
*
* 10/5/00 sameer Fixed isicom_shutdown_board()
* to not lower DTR on all the ports
- * when the last port on the card is
+ * when the last port on the card is
* closed.
*
* 10/5/00 sameer Signal mask setup command added
- * to isicom_setup_port and
+ * to isicom_setup_port and
* isicom_shutdown_port.
*
* 24/5/00 sameer The driver is now SMP aware.
- *
- *
+ *
+ *
* 27/11/00 Vinayak P Risbud Fixed the Driver Crash Problem
- *
- *
+ *
+ *
* 03/01/01 anil .s Added support for resetting the
* internal modems on ISI cards.
*
* 08/02/01 anil .s Upgraded the driver for kernel
* 2.4.x
*
- * 11/04/01 Kevin Fixed firmware load problem with
+ * 11/04/01 Kevin Fixed firmware load problem with
* ISIHP-4X card
- *
+ *
* 30/04/01 anil .s Fixed the remote login through
* ISI port problem. Now the link
* does not go down before password
@@ -62,9 +62,9 @@
* among ISI-PCI cards.
*
* 03/05/01 anil .s Added support to display the version
- * info during insmod as well as module
+ * info during insmod as well as module
* listing by lsmod.
- *
+ *
* 10/05/01 anil .s Done the modifications to the source
* file and Install script so that the
* same installation can be used for
@@ -73,7 +73,7 @@
* 06/06/01 anil .s Now we drop both dtr and rts during
* shutdown_port as well as raise them
* during isicom_config_port.
- *
+ *
* 09/06/01 [email protected] use capable, not suser, do
* restore_flags on failure in
* isicom_send_break, verify put_user
@@ -81,22 +81,24 @@
*
* 11/02/03 ranjeeth Added support for 230 Kbps and 460 Kbps
* Baud index extended to 21
- *
+ *
* 20/03/03 ranjeeth Made to work for Linux Advanced server.
- * Taken care of license warning.
- *
- * 10/12/03 Ravindra Made to work for Fedora Core 1 of
+ * Taken care of license warning.
+ *
+ * 10/12/03 Ravindra Made to work for Fedora Core 1 of
* Red Hat Distribution
*
* 06/01/05 Alan Cox Merged the ISI and base kernel strands
* into a single 2.6 driver
*
+ * 10/09/05 Jiri Slaby driver rewritten to 2.6 API
+ *
* ***********************************************************
*
- * To use this driver you also need the support package. You
+ * To use this driver you also need the support package. You
* can find this in RPM format on
* ftp://ftp.linux.org.uk/pub/linux/alan
- *
+ *
* You can find the original tools for this direct from Multitech
* ftp://ftp.multitech.com/ISI-Cards/
*
@@ -107,12 +109,12 @@
* Omit those entries for boards you don't have installed.
*
* TODO
- * Hotplug
* Merge testing
* 64-bit verification
*/
#include <linux/module.h>
+#include <linux/firmware.h>
#include <linux/kernel.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
@@ -121,7 +123,6 @@
#include <linux/sched.h>
#include <linux/serial.h>
#include <linux/mm.h>
-#include <linux/miscdevice.h>
#include <linux/interrupt.h>
#include <linux/timer.h>
#include <linux/delay.h>
@@ -135,74 +136,87 @@
#include <linux/isicom.h>
+#define InterruptTheCard(base) outw(0, (base) + 0xc)
+#define ClearInterrupt(base) inw((base) + 0x0a)
+
+#ifdef ISICOM_DEBUG
+#define pr_deb(str, ...) printk((str), ##args);
+#define isicom_paranoia_check(a, b, c) __isicom_paranoia_check((a), (b), (c))
+#else
+#define pr_deb(str, ...)
+#define isicom_paranoia_check(a, b, c) 0
+#endif
+
+static int isicom_probe(struct pci_dev*, const struct pci_device_id*);
+static void __devexit isicom_remove(struct pci_dev*);
+
static struct pci_device_id isicom_pci_tbl[] = {
- { VENDOR_ID, 0x2028, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2051, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2052, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2053, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2054, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2055, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2056, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2057, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
- { VENDOR_ID, 0x2058, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ { PCI_DEVICE(VENDOR_ID, 0x2028) },
+ { PCI_DEVICE(VENDOR_ID, 0x2051) },
+ { PCI_DEVICE(VENDOR_ID, 0x2052) },
+ { PCI_DEVICE(VENDOR_ID, 0x2053) },
+ { PCI_DEVICE(VENDOR_ID, 0x2054) },
+ { PCI_DEVICE(VENDOR_ID, 0x2055) },
+ { PCI_DEVICE(VENDOR_ID, 0x2056) },
+ { PCI_DEVICE(VENDOR_ID, 0x2057) },
+ { PCI_DEVICE(VENDOR_ID, 0x2058) },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, isicom_pci_tbl);
+static struct pci_driver isicom_driver = {
+ .name = "isicom",
+ .id_table = isicom_pci_tbl,
+ .probe = isicom_probe,
+ .remove = __devexit_p(isicom_remove)
+};
+
static int prev_card = 3; /* start servicing isi_card[0] */
static struct tty_driver *isicom_normal;
static struct timer_list tx;
static char re_schedule = 1;
-#ifdef ISICOM_DEBUG
-static unsigned long tx_count = 0;
-#endif
-
-static int ISILoad_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long arg);
static void isicom_tx(unsigned long _data);
-static void isicom_start(struct tty_struct * tty);
-
-static unsigned char * tmp_buf;
-static DECLARE_MUTEX(tmp_buf_sem);
+static void isicom_start(struct tty_struct *tty);
/* baud index mappings from linux defns to isi */
-static signed char linuxb_to_isib[] = {
- -1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 16, 17,
- 18, 19
+static s8 linuxb_to_isib[] = {
+ -1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 16, 17, 18, 19
};
struct isi_board {
- unsigned short base;
- unsigned char irq;
- unsigned char port_count;
- unsigned short status;
- unsigned short port_status; /* each bit represents a single port */
- unsigned short shift_count;
- struct isi_port * ports;
- signed char count;
- unsigned char isa;
+ u16 base;
+ u8 irq;
+ u8 port_count;
+ u16 status;
+ u16 port_status; /* each bit represents a ... */
+ u16 shift_count; /* ... single port */
+ struct isi_port *ports;
+ s8 count;
+ u8 isa;
spinlock_t card_lock; /* Card wide lock 11/5/00 -sameer */
unsigned long flags;
+ struct device device;
};
struct isi_port {
- unsigned short magic;
+ u16 magic;
unsigned int flags;
int count;
int blocked_open;
int close_delay;
- unsigned short channel;
- unsigned short status;
- unsigned short closing_wait;
- struct isi_board * card;
- struct tty_struct * tty;
+ u16 channel;
+ u16 status;
+ u16 closing_wait;
+ struct isi_board *card;
+ struct tty_struct *tty;
wait_queue_head_t close_wait;
wait_queue_head_t open_wait;
struct work_struct hangup_tq;
struct work_struct bh_tqueue;
- unsigned char * xmit_buf;
+ u8 *xmit_buf;
int xmit_head;
int xmit_tail;
int xmit_cnt;
@@ -216,16 +230,16 @@ static struct isi_port isi_ports[PORT_C
* the kernel lock for the card and have the card in a position that
* it wants to talk.
*/
-
+
static int lock_card(struct isi_board *card)
{
char retries;
- unsigned short base = card->base;
+ u16 base = card->base;
for (retries = 0; retries < 100; retries++) {
spin_lock_irqsave(&card->card_lock, card->flags);
if (inw(base + 0xe) & 0x1) {
- return 1;
+ return 1;
} else {
spin_unlock_irqrestore(&card->card_lock, card->flags);
udelay(1000); /* 1ms */
@@ -237,14 +251,14 @@ static int lock_card(struct isi_board *c
static int lock_card_at_interrupt(struct isi_board *card)
{
- unsigned char retries;
- unsigned short base = card->base;
+ u8 retries;
+ u16 base = card->base;
for (retries = 0; retries < 200; retries++) {
spin_lock_irqsave(&card->card_lock, card->flags);
if (inw(base + 0xe) & 0x1)
- return 1;
+ return 1;
else
spin_unlock_irqrestore(&card->card_lock, card->flags);
}
@@ -260,373 +274,141 @@ static void unlock_card(struct isi_board
/*
* ISI Card specific ops ...
*/
-
-static void raise_dtr(struct isi_port * port)
+
+static void raise_dtr(struct isi_port *port)
{
- struct isi_board * card = port->card;
- unsigned short base = card->base;
- unsigned char channel = port->channel;
+ struct isi_board *card = port->card;
+ u16 base = card->base;
+ u8 channel = port->channel;
if (!lock_card(card))
return;
- outw(0x8000 | (channel << card->shift_count) | 0x02 , base);
+ outw(0x8000 | (channel << card->shift_count) | 0x02, base);
outw(0x0504, base);
InterruptTheCard(base);
port->status |= ISI_DTR;
unlock_card(card);
}
-static inline void drop_dtr(struct isi_port * port)
-{
- struct isi_board * card = port->card;
- unsigned short base = card->base;
- unsigned char channel = port->channel;
+static inline void drop_dtr(struct isi_port *port)
+{
+ struct isi_board *card = port->card;
+ u16 base = card->base;
+ u8 channel = port->channel;
if (!lock_card(card))
return;
- outw(0x8000 | (channel << card->shift_count) | 0x02 , base);
+ outw(0x8000 | (channel << card->shift_count) | 0x02, base);
outw(0x0404, base);
- InterruptTheCard(base);
+ InterruptTheCard(base);
port->status &= ~ISI_DTR;
unlock_card(card);
}
-static inline void raise_rts(struct isi_port * port)
+static inline void raise_rts(struct isi_port *port)
{
- struct isi_board * card = port->card;
- unsigned short base = card->base;
- unsigned char channel = port->channel;
+ struct isi_board *card = port->card;
+ u16 base = card->base;
+ u8 channel = port->channel;
if (!lock_card(card))
return;
- outw(0x8000 | (channel << card->shift_count) | 0x02 , base);
+ outw(0x8000 | (channel << card->shift_count) | 0x02, base);
outw(0x0a04, base);
- InterruptTheCard(base);
+ InterruptTheCard(base);
port->status |= ISI_RTS;
unlock_card(card);
}
-static inline void drop_rts(struct isi_port * port)
+static inline void drop_rts(struct isi_port *port)
{
- struct isi_board * card = port->card;
- unsigned short base = card->base;
- unsigned char channel = port->channel;
+ struct isi_board *card = port->card;
+ u16 base = card->base;
+ u8 channel = port->channel;
if (!lock_card(card))
return;
- outw(0x8000 | (channel << card->shift_count) | 0x02 , base);
+ outw(0x8000 | (channel << card->shift_count) | 0x02, base);
outw(0x0804, base);
- InterruptTheCard(base);
+ InterruptTheCard(base);
port->status &= ~ISI_RTS;
unlock_card(card);
}
-static inline void raise_dtr_rts(struct isi_port * port)
+static inline void raise_dtr_rts(struct isi_port *port)
{
- struct isi_board * card = port->card;
- unsigned short base = card->base;
- unsigned char channel = port->channel;
+ struct isi_board *card = port->card;
+ u16 base = card->base;
+ u8 channel = port->channel;
if (!lock_card(card))
return;
- outw(0x8000 | (channel << card->shift_count) | 0x02 , base);
+ outw(0x8000 | (channel << card->shift_count) | 0x02, base);
outw(0x0f04, base);
InterruptTheCard(base);
port->status |= (ISI_DTR | ISI_RTS);
unlock_card(card);
}
-static void drop_dtr_rts(struct isi_port * port)
+static void drop_dtr_rts(struct isi_port *port)
{
- struct isi_board * card = port->card;
- unsigned short base = card->base;
- unsigned char channel = port->channel;
+ struct isi_board *card = port->card;
+ u16 base = card->base;
+ u8 channel = port->channel;
if (!lock_card(card))
return;
- outw(0x8000 | (channel << card->shift_count) | 0x02 , base);
+ outw(0x8000 | (channel << card->shift_count) | 0x02, base);
outw(0x0c04, base);
- InterruptTheCard(base);
+ InterruptTheCard(base);
port->status &= ~(ISI_RTS | ISI_DTR);
unlock_card(card);
}
-static inline void kill_queue(struct isi_port * port, short queue)
+static inline void kill_queue(struct isi_port *port, short queue)
{
- struct isi_board * card = port->card;
- unsigned short base = card->base;
- unsigned char channel = port->channel;
+ struct isi_board *card = port->card;
+ u16 base = card->base;
+ u8 channel = port->channel;
if (!lock_card(card))
return;
- outw(0x8000 | (channel << card->shift_count) | 0x02 , base);
+ outw(0x8000 | (channel << card->shift_count) | 0x02, base);
outw((queue << 8) | 0x06, base);
- InterruptTheCard(base);
+ InterruptTheCard(base);
unlock_card(card);
}
-
-/*
- * Firmware loader driver specific routines. This needs to mostly die
- * and be replaced with request_firmware.
- */
-
-static struct file_operations ISILoad_fops = {
- .owner = THIS_MODULE,
- .ioctl = ISILoad_ioctl,
-};
-
-static struct miscdevice isiloader_device = {
- ISILOAD_MISC_MINOR, "isictl", &ISILoad_fops
-};
-
-
-static inline int WaitTillCardIsFree(unsigned short base)
-{
- unsigned long count=0;
- while( (!(inw(base+0xe) & 0x1)) && (count++ < 6000000));
- if (inw(base+0xe)&0x1)
- return 0;
- else
- return 1;
-}
-
-static int ISILoad_ioctl(struct inode *inode, struct file *filp,
- unsigned int cmd, unsigned long arg)
-{
- unsigned int card, i, j, signature, status, portcount = 0;
- unsigned long t;
- unsigned short word_count, base;
- bin_frame frame;
- void __user *argp = (void __user *)arg;
- /* exec_record exec_rec; */
-
- if(get_user(card, (int __user *)argp))
- return -EFAULT;
-
- if(card < 0 || card >= BOARD_COUNT)
- return -ENXIO;
-
- base=isi_card[card].base;
-
- if(base==0)
- return -ENXIO; /* disabled or not used */
-
- switch(cmd) {
- case MIOCTL_RESET_CARD:
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
- printk(KERN_DEBUG "ISILoad:Resetting Card%d at 0x%x ",card+1,base);
-
- inw(base+0x8);
-
- for(t=jiffies+HZ/100;time_before(jiffies, t););
-
- outw(0,base+0x8); /* Reset */
-
- for(j=1;j<=3;j++) {
- for(t=jiffies+HZ;time_before(jiffies, t););
- printk(".");
- }
- signature=(inw(base+0x4)) & 0xff;
- if (isi_card[card].isa) {
-
- if (!(inw(base+0xe) & 0x1) || (inw(base+0x2))) {
-#ifdef ISICOM_DEBUG
- printk("\nbase+0x2=0x%x , base+0xe=0x%x",inw(base+0x2),inw(base+0xe));
-#endif
- printk("\nISILoad:ISA Card%d reset failure (Possible bad I/O Port Address 0x%x).\n",card+1,base);
- return -EIO;
- }
- }
- else {
- portcount = inw(base+0x2);
- if (!(inw(base+0xe) & 0x1) || ((portcount!=0) && (portcount!=4) && (portcount!=8))) {
-#ifdef ISICOM_DEBUG
- printk("\nbase+0x2=0x%x , base+0xe=0x%x",inw(base+0x2),inw(base+0xe));
-#endif
- printk("\nISILoad:PCI Card%d reset failure (Possible bad I/O Port Address 0x%x).\n",card+1,base);
- return -EIO;
- }
- }
- switch(signature) {
- case 0xa5:
- case 0xbb:
- case 0xdd:
- if (isi_card[card].isa)
- isi_card[card].port_count = 8;
- else {
- if (portcount == 4)
- isi_card[card].port_count = 4;
- else
- isi_card[card].port_count = 8;
- }
- isi_card[card].shift_count = 12;
- break;
-
- case 0xcc: isi_card[card].port_count = 16;
- isi_card[card].shift_count = 11;
- break;
-
- default: printk("ISILoad:Card%d reset failure (Possible bad I/O Port Address 0x%x).\n",card+1,base);
-#ifdef ISICOM_DEBUG
- printk("Sig=0x%x\n",signature);
-#endif
- return -EIO;
- }
- printk("-Done\n");
- return put_user(signature,(unsigned __user *)argp);
-
- case MIOCTL_LOAD_FIRMWARE:
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
-
- if(copy_from_user(&frame, argp, sizeof(bin_frame)))
- return -EFAULT;
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- outw(0xf0,base); /* start upload sequence */
- outw(0x00,base);
- outw((frame.addr), base);/* lsb of adderess */
-
- word_count=(frame.count >> 1) + frame.count % 2;
- outw(word_count, base);
- InterruptTheCard(base);
-
- for(i=0;i<=0x2f;i++); /* a wee bit of delay */
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- if ((status=inw(base+0x4))!=0) {
- printk(KERN_WARNING "ISILoad:Card%d rejected load header:\nAddress:0x%x \nCount:0x%x \nStatus:0x%x \n",
- card+1, frame.addr, frame.count, status);
- return -EIO;
- }
- outsw(base, (void *) frame.bin_data, word_count);
-
- InterruptTheCard(base);
-
- for(i=0;i<=0x0f;i++); /* another wee bit of delay */
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- if ((status=inw(base+0x4))!=0) {
- printk(KERN_ERR "ISILoad:Card%d got out of sync.Card Status:0x%x\n",card+1, status);
- return -EIO;
- }
- return 0;
-
- case MIOCTL_READ_FIRMWARE:
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
-
- if(copy_from_user(&frame, argp, sizeof(bin_header)))
- return -EFAULT;
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- outw(0xf1,base); /* start download sequence */
- outw(0x00,base);
- outw((frame.addr), base);/* lsb of adderess */
-
- word_count=(frame.count >> 1) + frame.count % 2;
- outw(word_count+1, base);
- InterruptTheCard(base);
-
- for(i=0;i<=0xf;i++); /* a wee bit of delay */
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- if ((status=inw(base+0x4))!=0) {
- printk(KERN_WARNING "ISILoad:Card%d rejected verify header:\nAddress:0x%x \nCount:0x%x \nStatus:0x%x \n",
- card+1, frame.addr, frame.count, status);
- return -EIO;
- }
-
- inw(base);
- insw(base, frame.bin_data, word_count);
- InterruptTheCard(base);
-
- for(i=0;i<=0x0f;i++); /* another wee bit of delay */
-
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- if ((status=inw(base+0x4))!=0) {
- printk(KERN_ERR "ISILoad:Card%d verify got out of sync.Card Status:0x%x\n",card+1, status);
- return -EIO;
- }
-
- if(copy_to_user(argp, &frame, sizeof(bin_frame)))
- return -EFAULT;
- return 0;
-
- case MIOCTL_XFER_CTRL:
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
- if (WaitTillCardIsFree(base))
- return -EIO;
-
- outw(0xf2, base);
- outw(0x800, base);
- outw(0x0, base);
- outw(0x0, base);
- InterruptTheCard(base);
- outw(0x0, base+0x4); /* for ISI4608 cards */
-
- isi_card[card].status |= FIRMWARE_LOADED;
- return 0;
-
- default:
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISILoad: Received Ioctl cmd 0x%x.\n", cmd);
-#endif
- return -ENOIOCTLCMD;
-
- }
-
-}
-
-
/*
* ISICOM Driver specific routines ...
*
*/
-
-static inline int isicom_paranoia_check(struct isi_port const * port, char *name,
- const char * routine)
+
+static inline int __isicom_paranoia_check(struct isi_port const *port,
+ char *name, const char *routine)
{
-#ifdef ISICOM_DEBUG
- static const char * badmagic =
- KERN_WARNING "ISICOM: Warning: bad isicom magic for dev %s in %s.\n";
- static const char * badport =
- KERN_WARNING "ISICOM: Warning: NULL isicom port for dev %s in %s.\n";
if (!port) {
- printk(badport, name, routine);
+ printk(KERN_WARNING "ISICOM: Warning: bad isicom magic for "
+ "dev %s in %s.\n", name, routine);
return 1;
}
if (port->magic != ISICOM_MAGIC) {
- printk(badmagic, name, routine);
+ printk(KERN_WARNING "ISICOM: Warning: NULL isicom port for "
+ "dev %s in %s.\n", name, routine);
return 1;
- }
-#endif
+ }
+
return 0;
}
-
+
/*
- * Transmitter.
+ * Transmitter.
*
* We shovel data into the card buffers on a regular basis. The card
* will do the rest of the work for us.
@@ -636,25 +418,21 @@ static void isicom_tx(unsigned long _dat
{
short count = (BOARD_COUNT-1), card, base;
short txcount, wrd, residue, word_count, cnt;
- struct isi_port * port;
- struct tty_struct * tty;
-
-#ifdef ISICOM_DEBUG
- ++tx_count;
-#endif
-
+ struct isi_port *port;
+ struct tty_struct *tty;
+
/* find next active board */
card = (prev_card + 1) & 0x0003;
while(count-- > 0) {
- if (isi_card[card].status & BOARD_ACTIVE)
+ if (isi_card[card].status & BOARD_ACTIVE)
break;
- card = (card + 1) & 0x0003;
+ card = (card + 1) & 0x0003;
}
if (!(isi_card[card].status & BOARD_ACTIVE))
goto sched_again;
-
+
prev_card = card;
-
+
count = isi_card[card].port_count;
port = isi_card[card].ports;
base = isi_card[card].base;
@@ -663,18 +441,18 @@ static void isicom_tx(unsigned long _dat
continue;
/* port not active or tx disabled to force flow control */
if (!(port->flags & ASYNC_INITIALIZED) ||
- !(port->status & ISI_TXOK))
+ !(port->status & ISI_TXOK))
unlock_card(&isi_card[card]);
continue;
-
+
tty = port->tty;
-
-
+
+
if(tty == NULL) {
unlock_card(&isi_card[card]);
continue;
}
-
+
txcount = min_t(short, TX_SIZE, port->xmit_cnt);
if (txcount <= 0 || tty->stopped || tty->hw_stopped) {
unlock_card(&isi_card[card]);
@@ -682,44 +460,45 @@ static void isicom_tx(unsigned long _dat
}
if (!(inw(base + 0x02) & (1 << port->channel))) {
unlock_card(&isi_card[card]);
- continue;
+ continue;
}
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: txing %d bytes, port%d.\n",
- txcount, port->channel+1);
-#endif
- outw((port->channel << isi_card[card].shift_count) | txcount
- , base);
+ pr_deb(KERN_DEBUG "ISICOM: txing %d bytes, port%d.\n",
+ txcount, port->channel+1);
+ outw((port->channel << isi_card[card].shift_count) | txcount,
+ base);
residue = NO;
- wrd = 0;
+ wrd = 0;
while (1) {
- cnt = min_t(int, txcount, (SERIAL_XMIT_SIZE - port->xmit_tail));
+ cnt = min_t(int, txcount, (SERIAL_XMIT_SIZE
+ - port->xmit_tail));
if (residue == YES) {
residue = NO;
if (cnt > 0) {
- wrd |= (port->xmit_buf[port->xmit_tail] << 8);
- port->xmit_tail = (port->xmit_tail + 1) & (SERIAL_XMIT_SIZE - 1);
+ wrd |= (port->xmit_buf[port->xmit_tail]
+ << 8);
+ port->xmit_tail = (port->xmit_tail + 1)
+ & (SERIAL_XMIT_SIZE - 1);
port->xmit_cnt--;
txcount--;
cnt--;
- outw(wrd, base);
- }
- else {
+ outw(wrd, base);
+ } else {
outw(wrd, base);
break;
}
- }
+ }
if (cnt <= 0) break;
word_count = cnt >> 1;
outsw(base, port->xmit_buf+port->xmit_tail, word_count);
- port->xmit_tail = (port->xmit_tail + (word_count << 1)) &
- (SERIAL_XMIT_SIZE - 1);
+ port->xmit_tail = (port->xmit_tail
+ + (word_count << 1)) & (SERIAL_XMIT_SIZE - 1);
txcount -= (word_count << 1);
port->xmit_cnt -= (word_count << 1);
if (cnt & 0x0001) {
residue = YES;
wrd = port->xmit_buf[port->xmit_tail];
- port->xmit_tail = (port->xmit_tail + 1) & (SERIAL_XMIT_SIZE - 1);
+ port->xmit_tail = (port->xmit_tail + 1) &
+ (SERIAL_XMIT_SIZE - 1);
port->xmit_cnt--;
txcount--;
}
@@ -731,82 +510,81 @@ static void isicom_tx(unsigned long _dat
if (port->xmit_cnt <= WAKEUP_CHARS)
schedule_work(&port->bh_tqueue);
unlock_card(&isi_card[card]);
- }
+ }
- /* schedule another tx for hopefully in about 10ms */
-sched_again:
- if (!re_schedule)
+ /* schedule another tx for hopefully in about 10ms */
+sched_again:
+ if (!re_schedule) {
+ re_schedule = 2;
return;
+ }
init_timer(&tx);
tx.expires = jiffies + HZ/100;
tx.data = 0;
tx.function = isicom_tx;
add_timer(&tx);
-
- return;
-}
-
+
+ return;
+}
+
/* Interrupt handlers */
-
-static void isicom_bottomhalf(void * data)
+
+static void isicom_bottomhalf(void *data)
{
- struct isi_port * port = (struct isi_port *) data;
- struct tty_struct * tty = port->tty;
-
+ struct isi_port *port = data;
+ struct tty_struct *tty = port->tty;
+
if (!tty)
return;
- tty_wakeup(tty);
+ tty_wakeup(tty);
wake_up_interruptible(&tty->write_wait);
-}
-
+}
+
/*
- * Main interrupt handler routine
+ * Main interrupt handler routine
*/
-
-static irqreturn_t isicom_interrupt(int irq, void *dev_id,
- struct pt_regs *regs)
+
+static irqreturn_t isicom_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
- struct isi_board * card;
- struct isi_port * port;
- struct tty_struct * tty;
- unsigned short base, header, word_count, count;
- unsigned char channel;
+ struct isi_board *card = dev_id;
+ struct isi_port *port;
+ struct tty_struct *tty;
+ u16 base, header, word_count, count;
+ u8 channel;
short byte_count;
unsigned char *rp;
-
- card = (struct isi_board *) dev_id;
if (!card || !(card->status & FIRMWARE_LOADED))
return IRQ_NONE;
-
+
base = card->base;
spin_lock(&card->card_lock);
-
+
if (card->isa == NO) {
/*
- * disable any interrupts from the PCI card and lower the
- * interrupt line
+ * disable any interrupts from the PCI card and lower the
+ * interrupt line
*/
outw(0x8000, base+0x04);
ClearInterrupt(base);
}
-
+
inw(base); /* get the dummy word out */
header = inw(base);
channel = (header & 0x7800) >> card->shift_count;
byte_count = header & 0xff;
if (channel + 1 > card->port_count) {
- printk(KERN_WARNING "ISICOM: isicom_interrupt(0x%x): %d(channel) > port_count.\n",
- base, channel+1);
+ printk(KERN_WARNING "ISICOM: isicom_interrupt(0x%x): "
+ "%d(channel) > port_count.\n", base, channel + 1);
if (card->isa)
ClearInterrupt(base);
else
- outw(0x0000, base+0x04); /* enable interrupts */
+ outw(0x0000, base+0x04); /* enable interrupts */
spin_unlock(&card->card_lock);
- return IRQ_HANDLED;
+ return IRQ_HANDLED;
}
port = card->ports + channel;
if (!(port->flags & ASYNC_INITIALIZED)) {
@@ -815,8 +593,8 @@ static irqreturn_t isicom_interrupt(int
else
outw(0x0000, base+0x04); /* enable interrupts */
return IRQ_HANDLED;
- }
-
+ }
+
tty = port->tty;
if (tty == NULL) {
word_count = byte_count >> 1;
@@ -833,109 +611,102 @@ static irqreturn_t isicom_interrupt(int
spin_unlock(&card->card_lock);
return IRQ_HANDLED;
}
-
+
if (header & 0x8000) { /* Status Packet */
header = inw(base);
switch(header & 0xff) {
- case 0: /* Change in EIA signals */
-
- if (port->flags & ASYNC_CHECK_CD) {
- if (port->status & ISI_DCD) {
- if (!(header & ISI_DCD)) {
- /* Carrier has been lost */
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: interrupt: DCD->low.\n");
-#endif
- port->status &= ~ISI_DCD;
- schedule_work(&port->hangup_tq);
- }
- }
- else {
- if (header & ISI_DCD) {
- /* Carrier has been detected */
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: interrupt: DCD->high.\n");
-#endif
- port->status |= ISI_DCD;
- wake_up_interruptible(&port->open_wait);
- }
- }
- }
- else {
- if (header & ISI_DCD)
- port->status |= ISI_DCD;
- else
+ case 0: /* Change in EIA signals */
+ if (port->flags & ASYNC_CHECK_CD) {
+ if (port->status & ISI_DCD) {
+ if (!(header & ISI_DCD)) {
+ /* Carrier has been lost */
+ pr_deb(KERN_DEBUG "ISICOM: "
+ "interrupt: "
+ "DCD->low.\n");
port->status &= ~ISI_DCD;
- }
-
- if (port->flags & ASYNC_CTS_FLOW) {
- if (port->tty->hw_stopped) {
- if (header & ISI_CTS) {
- port->tty->hw_stopped = 0;
- /* start tx ing */
- port->status |= (ISI_TXOK | ISI_CTS);
- schedule_work(&port->bh_tqueue);
- }
+ schedule_work(&port->hangup_tq);
}
- else {
- if (!(header & ISI_CTS)) {
- port->tty->hw_stopped = 1;
- /* stop tx ing */
- port->status &= ~(ISI_TXOK | ISI_CTS);
- }
- }
- }
- else {
- if (header & ISI_CTS)
- port->status |= ISI_CTS;
- else
- port->status &= ~ISI_CTS;
+ } else if (header & ISI_DCD) {
+ /* Carrier has been detected */
+ pr_deb(KERN_DEBUG "ISICOM: "
+ "interrupt: "
+ "DCD->high.\n");
+ port->status |= ISI_DCD;
+ wake_up_interruptible(
+ &port->open_wait);
}
-
- if (header & ISI_DSR)
- port->status |= ISI_DSR;
+ } else {
+ if (header & ISI_DCD)
+ port->status |= ISI_DCD;
else
- port->status &= ~ISI_DSR;
-
- if (header & ISI_RI)
- port->status |= ISI_RI;
+ port->status &= ~ISI_DCD;
+ }
+
+ if (port->flags & ASYNC_CTS_FLOW) {
+ if (port->tty->hw_stopped) {
+ if (header & ISI_CTS) {
+ port->tty->hw_stopped = 0;
+ /* start tx ing */
+ port->status |= (ISI_TXOK |
+ ISI_CTS);
+ schedule_work(&port->bh_tqueue);
+ }
+ } else if (!(header & ISI_CTS)) {
+ port->tty->hw_stopped = 1;
+ /* stop tx ing */
+ port->status &= ~(ISI_TXOK |
+ ISI_CTS);
+ }
+ } else if (header & ISI_CTS)
+ port->status |= ISI_CTS;
else
- port->status &= ~ISI_RI;
-
- break;
-
- case 1: /* Received Break !!! */
- tty_insert_flip_char(tty, 0, TTY_BREAK);
- if (port->flags & ASYNC_SAK)
- do_SAK(tty);
- tty_flip_buffer_push(tty);
- break;
-
- case 2: /* Statistics */
- printk(KERN_DEBUG "ISICOM: isicom_interrupt: stats!!!.\n");
- break;
-
- default:
- printk(KERN_WARNING "ISICOM: Intr: Unknown code in status packet.\n");
- break;
- }
- }
- else { /* Data Packet */
+ port->status &= ~ISI_CTS;
+
+ if (header & ISI_DSR)
+ port->status |= ISI_DSR;
+ else
+ port->status &= ~ISI_DSR;
+
+ if (header & ISI_RI)
+ port->status |= ISI_RI;
+ else
+ port->status &= ~ISI_RI;
+
+ break;
+
+ case 1: /* Received Break !!! */
+ tty_insert_flip_char(tty, 0, TTY_BREAK);
+ if (port->flags & ASYNC_SAK)
+ do_SAK(tty);
+ tty_flip_buffer_push(tty);
+ break;
+
+ case 2: /* Statistics */
+ printk(KERN_DEBUG "ISICOM: isicom_interrupt: "
+ "stats!!!.\n");
+ break;
+
+ default:
+ printk(KERN_WARNING "ISICOM: Intr: Unknown code in "
+ "status packet.\n");
+ break;
+ }
+ } else { /* Data Packet */
count = tty_prepare_flip_string(tty, &rp, byte_count & ~1);
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: Intr: Can rx %d of %d bytes.\n",
+ pr_deb(KERN_DEBUG "ISICOM: Intr: Can rx %d of %d bytes.\n",
count, byte_count);
-#endif
word_count = count >> 1;
insw(base, rp, word_count);
byte_count -= (word_count << 1);
if (count & 0x0001) {
- tty_insert_flip_char(tty, inw(base) & 0xff, TTY_NORMAL);
+ tty_insert_flip_char(tty, inw(base) & 0xff,
+ TTY_NORMAL);
byte_count -= 2;
- }
+ }
if (byte_count > 0) {
- printk(KERN_DEBUG "ISICOM: Intr(0x%x:%d): Flip buffer overflow! dropping bytes...\n",
+ printk(KERN_DEBUG "ISICOM: Intr(0x%x:%d): Flip buffer "
+ "overflow! dropping bytes...\n",
base, channel+1);
while(byte_count > 0) { /* drain out unread xtra data */
inw(base);
@@ -947,55 +718,54 @@ static irqreturn_t isicom_interrupt(int
if (card->isa == YES)
ClearInterrupt(base);
else
- outw(0x0000, base+0x04); /* enable interrupts */
+ outw(0x0000, base+0x04); /* enable interrupts */
return IRQ_HANDLED;
-}
+}
-static void isicom_config_port(struct isi_port * port)
+static void isicom_config_port(struct isi_port *port)
{
- struct isi_board * card = port->card;
- struct tty_struct * tty;
+ struct isi_board *card = port->card;
+ struct tty_struct *tty;
unsigned long baud;
- unsigned short channel_setup, base = card->base;
- unsigned short channel = port->channel, shift_count = card->shift_count;
- unsigned char flow_ctrl;
-
+ u16 channel_setup, base = card->base;
+ u16 channel = port->channel, shift_count = card->shift_count;
+ u8 flow_ctrl;
+
if (!(tty = port->tty) || !tty->termios)
return;
baud = C_BAUD(tty);
if (baud & CBAUDEX) {
baud &= ~CBAUDEX;
-
+
/* if CBAUDEX bit is on and the baud is set to either 50 or 75
* then the card is programmed for 57.6Kbps or 115Kbps
* respectively.
- */
-
+ */
+
if (baud < 1 || baud > 2)
port->tty->termios->c_cflag &= ~CBAUDEX;
else
baud += 15;
- }
+ }
if (baud == 15) {
-
- /* the ASYNC_SPD_HI and ASYNC_SPD_VHI options are set
+
+ /* the ASYNC_SPD_HI and ASYNC_SPD_VHI options are set
* by the set_serial_info ioctl ... this is done by
* the 'setserial' utility.
- */
-
+ */
+
if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
- baud++; /* 57.6 Kbps */
+ baud++; /* 57.6 Kbps */
if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
- baud +=2; /* 115 Kbps */
+ baud += 2; /* 115 Kbps */
}
if (linuxb_to_isib[baud] == -1) {
/* hang up */
- drop_dtr(port);
- return;
- }
- else
+ drop_dtr(port);
+ return;
+ } else
raise_dtr(port);
-
+
if (lock_card(card)) {
outw(0x8000 | (channel << shift_count) |0x03, base);
outw(linuxb_to_isib[baud] << 8 | 0x03, base);
@@ -1014,35 +784,35 @@ static void isicom_config_port(struct is
channel_setup |= ISICOM_CS8;
break;
}
-
+
if (C_CSTOPB(tty))
channel_setup |= ISICOM_2SB;
if (C_PARENB(tty)) {
channel_setup |= ISICOM_EVPAR;
if (C_PARODD(tty))
- channel_setup |= ISICOM_ODPAR;
+ channel_setup |= ISICOM_ODPAR;
}
- outw(channel_setup, base);
+ outw(channel_setup, base);
InterruptTheCard(base);
- unlock_card(card);
- }
+ unlock_card(card);
+ }
if (C_CLOCAL(tty))
port->flags &= ~ASYNC_CHECK_CD;
else
- port->flags |= ASYNC_CHECK_CD;
-
+ port->flags |= ASYNC_CHECK_CD;
+
/* flow control settings ...*/
flow_ctrl = 0;
port->flags &= ~ASYNC_CTS_FLOW;
if (C_CRTSCTS(tty)) {
port->flags |= ASYNC_CTS_FLOW;
flow_ctrl |= ISICOM_CTSRTS;
- }
- if (I_IXON(tty))
+ }
+ if (I_IXON(tty))
flow_ctrl |= ISICOM_RESPOND_XONXOFF;
if (I_IXOFF(tty))
- flow_ctrl |= ISICOM_INITIATE_XONXOFF;
-
+ flow_ctrl |= ISICOM_INITIATE_XONXOFF;
+
if (lock_card(card)) {
outw(0x8000 | (channel << shift_count) |0x04, base);
outw(flow_ctrl << 8 | 0x05, base);
@@ -1050,22 +820,22 @@ static void isicom_config_port(struct is
InterruptTheCard(base);
unlock_card(card);
}
-
+
/* rx enabled -> enable port for rx on the card */
if (C_CREAD(tty)) {
card->port_status |= (1 << channel);
outw(card->port_status, base + 0x02);
}
}
-
-/* open et all */
-static inline void isicom_setup_board(struct isi_board * bp)
+/* open et all */
+
+static inline void isicom_setup_board(struct isi_board *bp)
{
int channel;
- struct isi_port * port;
+ struct isi_port *port;
unsigned long flags;
-
+
spin_lock_irqsave(&bp->card_lock, flags);
if (bp->status & BOARD_ACTIVE) {
spin_unlock_irqrestore(&bp->card_lock, flags);
@@ -1078,49 +848,50 @@ static inline void isicom_setup_board(st
drop_dtr_rts(port);
return;
}
-
-static int isicom_setup_port(struct isi_port * port)
+
+static int isicom_setup_port(struct isi_port *port)
{
- struct isi_board * card = port->card;
+ struct isi_board *card = port->card;
unsigned long flags;
-
+
if (port->flags & ASYNC_INITIALIZED) {
return 0;
}
if (!port->xmit_buf) {
unsigned long page;
-
+
if (!(page = get_zeroed_page(GFP_KERNEL)))
return -ENOMEM;
-
+
if (port->xmit_buf) {
free_page(page);
return -ERESTARTSYS;
}
- port->xmit_buf = (unsigned char *) page;
- }
+ port->xmit_buf = (u8*)page;
+ }
spin_lock_irqsave(&card->card_lock, flags);
if (port->tty)
clear_bit(TTY_IO_ERROR, &port->tty->flags);
if (port->count == 1)
card->count++;
-
+
port->xmit_cnt = port->xmit_head = port->xmit_tail = 0;
-
+
/* discard any residual data */
kill_queue(port, ISICOM_KILLTX | ISICOM_KILLRX);
-
+
isicom_config_port(port);
port->flags |= ASYNC_INITIALIZED;
spin_unlock_irqrestore(&card->card_lock, flags);
-
- return 0;
-}
-
-static int block_til_ready(struct tty_struct * tty, struct file * filp, struct isi_port * port)
+
+ return 0;
+}
+
+static int block_til_ready(struct tty_struct *tty, struct file *filp,
+ struct isi_port *port)
{
- struct isi_board * card = port->card;
+ struct isi_board *card = port->card;
int do_clocal = 0, retval;
unsigned long flags;
DECLARE_WAITQUEUE(wait, current);
@@ -1128,30 +899,28 @@ static int block_til_ready(struct tty_st
/* block if port is in the process of being closed */
if (tty_hung_up_p(filp) || port->flags & ASYNC_CLOSING) {
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: block_til_ready: close in progress.\n");
-#endif
+ pr_deb(KERN_DEBUG "ISICOM: block_til_ready: close in "
+ "progress.\n");
interruptible_sleep_on(&port->close_wait);
if (port->flags & ASYNC_HUP_NOTIFY)
return -EAGAIN;
else
return -ERESTARTSYS;
}
-
+
/* if non-blocking mode is set ... */
-
- if ((filp->f_flags & O_NONBLOCK) || (tty->flags & (1 << TTY_IO_ERROR))) {
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: block_til_ready: non-block mode.\n");
-#endif
+
+ if ((filp->f_flags & O_NONBLOCK) ||
+ (tty->flags & (1 << TTY_IO_ERROR))) {
+ pr_deb(KERN_DEBUG "ISICOM: block_til_ready: non-block mode.\n");
port->flags |= ASYNC_NORMAL_ACTIVE;
- return 0;
- }
-
+ return 0;
+ }
+
if (C_CLOCAL(tty))
do_clocal = 1;
-
- /* block waiting for DCD to be asserted, and while
+
+ /* block waiting for DCD to be asserted, and while
callout dev is busy */
retval = 0;
add_wait_queue(&port->open_wait, &wait);
@@ -1161,27 +930,27 @@ static int block_til_ready(struct tty_st
port->count--;
port->blocked_open++;
spin_unlock_irqrestore(&card->card_lock, flags);
-
+
while (1) {
raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)) {
+ if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)) {
if (port->flags & ASYNC_HUP_NOTIFY)
retval = -EAGAIN;
else
retval = -ERESTARTSYS;
break;
- }
+ }
if (!(port->flags & ASYNC_CLOSING) &&
- (do_clocal || (port->status & ISI_DCD))) {
+ (do_clocal || (port->status & ISI_DCD))) {
break;
- }
+ }
if (signal_pending(current)) {
retval = -ERESTARTSYS;
break;
}
- schedule();
+ schedule();
}
set_current_state(TASK_RUNNING);
remove_wait_queue(&port->open_wait, &wait);
@@ -1195,11 +964,11 @@ static int block_til_ready(struct tty_st
port->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
-
-static int isicom_open(struct tty_struct * tty, struct file * filp)
+
+static int isicom_open(struct tty_struct *tty, struct file *filp)
{
- struct isi_port * port;
- struct isi_board * card;
+ struct isi_port *port;
+ struct isi_board *card;
unsigned int line, board;
int error;
@@ -1208,20 +977,20 @@ static int isicom_open(struct tty_struct
return -ENODEV;
board = BOARD(line);
card = &isi_card[board];
-
+
if (!(card->status & FIRMWARE_LOADED))
return -ENODEV;
-
+
/* open on a port greater than the port count for the card !!! */
if (line > ((board * 16) + card->port_count - 1))
return -ENODEV;
- port = &isi_ports[line];
+ port = &isi_ports[line];
if (isicom_paranoia_check(port, tty->name, "isicom_open"))
return -ENODEV;
-
- isicom_setup_board(card);
-
+
+ isicom_setup_board(card);
+
port->count++;
tty->driver_data = port;
port->tty = tty;
@@ -1230,12 +999,12 @@ static int isicom_open(struct tty_struct
if ((error = block_til_ready(tty, filp, port))!=0)
return error;
- return 0;
+ return 0;
}
-
+
/* close et all */
-static inline void isicom_shutdown_board(struct isi_board * bp)
+static inline void isicom_shutdown_board(struct isi_board *bp)
{
unsigned long flags;
@@ -1246,15 +1015,15 @@ static inline void isicom_shutdown_board
spin_unlock_irqrestore(&bp->card_lock, flags);
}
-static void isicom_shutdown_port(struct isi_port * port)
+static void isicom_shutdown_port(struct isi_port *port)
{
- struct isi_board * card = port->card;
- struct tty_struct * tty;
+ struct isi_board *card = port->card;
+ struct tty_struct *tty;
unsigned long flags;
-
+
tty = port->tty;
- spin_lock_irqsave(&card->card_lock, flags);
+ spin_lock_irqsave(&card->card_lock, flags);
if (!(port->flags & ASYNC_INITIALIZED)) {
spin_unlock_irqrestore(&card->card_lock, flags);
return;
@@ -1262,32 +1031,32 @@ static void isicom_shutdown_port(struct
if (port->xmit_buf) {
free_page((unsigned long) port->xmit_buf);
port->xmit_buf = NULL;
- }
+ }
port->flags &= ~ASYNC_INITIALIZED;
/* 3rd October 2000 : Vinayak P Risbud */
port->tty = NULL;
spin_unlock_irqrestore(&card->card_lock, flags);
-
+
/*Fix done by Anil .S on 30-04-2001
remote login through isi port has dtr toggle problem
due to which the carrier drops before the password prompt
- appears on the remote end. Now we drop the dtr only if the
+ appears on the remote end. Now we drop the dtr only if the
HUPCL(Hangup on close) flag is set for the tty*/
-
- if (C_HUPCL(tty))
+
+ if (C_HUPCL(tty))
/* drop dtr on this port */
drop_dtr(port);
-
- /* any other port uninits */
+
+ /* any other port uninits */
if (tty)
set_bit(TTY_IO_ERROR, &tty->flags);
-
+
if (--card->count < 0) {
- printk(KERN_DEBUG "ISICOM: isicom_shutdown_port: bad board(0x%x) count %d.\n",
- card->base, card->count);
- card->count = 0;
+ printk(KERN_DEBUG "ISICOM: isicom_shutdown_port: bad "
+ "board(0x%x) count %d.\n", card->base, card->count);
+ card->count = 0;
}
-
+
/* last port was closed , shutdown that boad too */
if(C_HUPCL(tty)) {
if (!card->count)
@@ -1295,27 +1064,25 @@ static void isicom_shutdown_port(struct
}
}
-static void isicom_close(struct tty_struct * tty, struct file * filp)
+static void isicom_close(struct tty_struct *tty, struct file *filp)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
- struct isi_board * card = port->card;
+ struct isi_port *port = (struct isi_port *) tty->driver_data;
+ struct isi_board *card = port->card;
unsigned long flags;
-
+
if (!port)
return;
if (isicom_paranoia_check(port, tty->name, "isicom_close"))
return;
-
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: Close start!!!.\n");
-#endif
-
+
+ pr_deb(KERN_DEBUG "ISICOM: Close start!!!.\n");
+
spin_lock_irqsave(&card->card_lock, flags);
if (tty_hung_up_p(filp)) {
spin_unlock_irqrestore(&card->card_lock, flags);
return;
}
-
+
if (tty->count == 1 && port->count != 1) {
printk(KERN_WARNING "ISICOM:(0x%x) isicom_close: bad port count"
"tty->count = 1 port count = %d.\n",
@@ -1323,32 +1090,32 @@ static void isicom_close(struct tty_stru
port->count = 1;
}
if (--port->count < 0) {
- printk(KERN_WARNING "ISICOM:(0x%x) isicom_close: bad port count for"
- "channel%d = %d", card->base, port->channel,
+ printk(KERN_WARNING "ISICOM:(0x%x) isicom_close: bad port "
+ "count for channel%d = %d", card->base, port->channel,
port->count);
- port->count = 0;
+ port->count = 0;
}
-
+
if (port->count) {
spin_unlock_irqrestore(&card->card_lock, flags);
return;
- }
+ }
port->flags |= ASYNC_CLOSING;
tty->closing = 1;
spin_unlock_irqrestore(&card->card_lock, flags);
-
+
if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE)
tty_wait_until_sent(tty, port->closing_wait);
- /* indicate to the card that no more data can be received
+ /* indicate to the card that no more data can be received
on this port */
spin_lock_irqsave(&card->card_lock, flags);
- if (port->flags & ASYNC_INITIALIZED) {
+ if (port->flags & ASYNC_INITIALIZED) {
card->port_status &= ~(1 << port->channel);
outw(card->port_status, card->base + 0x02);
- }
+ }
isicom_shutdown_port(port);
spin_unlock_irqrestore(&card->card_lock, flags);
-
+
if (tty->driver->flush_buffer)
tty->driver->flush_buffer(tty);
tty_ldisc_flush(tty);
@@ -1359,65 +1126,65 @@ static void isicom_close(struct tty_stru
if (port->blocked_open) {
spin_unlock_irqrestore(&card->card_lock, flags);
if (port->close_delay) {
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: scheduling until time out.\n");
-#endif
- msleep_interruptible(jiffies_to_msecs(port->close_delay));
+ pr_deb(KERN_DEBUG "ISICOM: scheduling until time "
+ "out.\n");
+ msleep_interruptible(
+ jiffies_to_msecs(port->close_delay));
}
spin_lock_irqsave(&card->card_lock, flags);
wake_up_interruptible(&port->open_wait);
- }
+ }
port->flags &= ~(ASYNC_NORMAL_ACTIVE | ASYNC_CLOSING);
wake_up_interruptible(&port->close_wait);
spin_unlock_irqrestore(&card->card_lock, flags);
}
/* write et all */
-static int isicom_write(struct tty_struct * tty,
- const unsigned char * buf, int count)
+static int isicom_write(struct tty_struct *tty, const u8 *buf, int count)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
- struct isi_board * card = port->card;
+ struct isi_port *port = tty->driver_data;
+ struct isi_board *card = port->card;
unsigned long flags;
int cnt, total = 0;
if (isicom_paranoia_check(port, tty->name, "isicom_write"))
return 0;
-
- if (!tty || !port->xmit_buf || !tmp_buf)
+
+ if (!tty || !port->xmit_buf)
return 0;
-
+
spin_lock_irqsave(&card->card_lock, flags);
-
- while(1) {
- cnt = min_t(int, count, min(SERIAL_XMIT_SIZE - port->xmit_cnt - 1,
- SERIAL_XMIT_SIZE - port->xmit_head));
- if (cnt <= 0)
+
+ while(1) {
+ cnt = min_t(int, count, min(SERIAL_XMIT_SIZE - port->xmit_cnt
+ - 1, SERIAL_XMIT_SIZE - port->xmit_head));
+ if (cnt <= 0)
break;
-
+
memcpy(port->xmit_buf + port->xmit_head, buf, cnt);
- port->xmit_head = (port->xmit_head + cnt) & (SERIAL_XMIT_SIZE - 1);
+ port->xmit_head = (port->xmit_head + cnt) & (SERIAL_XMIT_SIZE
+ - 1);
port->xmit_cnt += cnt;
buf += cnt;
count -= cnt;
total += cnt;
- }
+ }
if (port->xmit_cnt && !tty->stopped && !tty->hw_stopped)
port->status |= ISI_TXOK;
spin_unlock_irqrestore(&card->card_lock, flags);
- return total;
+ return total;
}
/* put_char et all */
-static void isicom_put_char(struct tty_struct * tty, unsigned char ch)
+static void isicom_put_char(struct tty_struct *tty, u8 ch)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
- struct isi_board * card = port->card;
+ struct isi_port *port = tty->driver_data;
+ struct isi_board *card = port->card;
unsigned long flags;
-
+
if (isicom_paranoia_check(port, tty->name, "isicom_put_char"))
return;
-
+
if (!tty || !port->xmit_buf)
return;
@@ -1426,7 +1193,7 @@ static void isicom_put_char(struct tty_s
spin_unlock_irqrestore(&card->card_lock, flags);
return;
}
-
+
port->xmit_buf[port->xmit_head++] = ch;
port->xmit_head &= (SERIAL_XMIT_SIZE - 1);
port->xmit_cnt++;
@@ -1434,30 +1201,31 @@ static void isicom_put_char(struct tty_s
}
/* flush_chars et all */
-static void isicom_flush_chars(struct tty_struct * tty)
+static void isicom_flush_chars(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
-
+ struct isi_port *port = tty->driver_data;
+
if (isicom_paranoia_check(port, tty->name, "isicom_flush_chars"))
return;
-
- if (port->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped || !port->xmit_buf)
+
+ if (port->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
+ !port->xmit_buf)
return;
-
+
/* this tells the transmitter to consider this port for
data output to the card ... that's the best we can do. */
- port->status |= ISI_TXOK;
+ port->status |= ISI_TXOK;
}
/* write_room et all */
-static int isicom_write_room(struct tty_struct * tty)
+static int isicom_write_room(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
+ struct isi_port *port = tty->driver_data;
int free;
if (isicom_paranoia_check(port, tty->name, "isicom_write_room"))
return 0;
-
+
free = SERIAL_XMIT_SIZE - port->xmit_cnt - 1;
if (free < 0)
free = 0;
@@ -1465,23 +1233,24 @@ static int isicom_write_room(struct tty_
}
/* chars_in_buffer et all */
-static int isicom_chars_in_buffer(struct tty_struct * tty)
+static int isicom_chars_in_buffer(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
+ struct isi_port *port = tty->driver_data;
if (isicom_paranoia_check(port, tty->name, "isicom_chars_in_buffer"))
return 0;
return port->xmit_cnt;
}
/* ioctl et all */
-static inline void isicom_send_break(struct isi_port * port, unsigned long length)
+static inline void isicom_send_break(struct isi_port *port,
+ unsigned long length)
{
- struct isi_board * card = port->card;
- unsigned short base = card->base;
-
+ struct isi_board *card = port->card;
+ u16 base = card->base;
+
if(!lock_card(card))
return;
-
+
outw(0x8000 | ((port->channel) << (card->shift_count)) | 0x3, base);
outw((length & 0xff) << 8 | 0x00, base);
outw((length & 0xff00), base);
@@ -1492,13 +1261,13 @@ static inline void isicom_send_break(str
static int isicom_tiocmget(struct tty_struct *tty, struct file *file)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
+ struct isi_port *port = tty->driver_data;
/* just send the port status */
- unsigned short status = port->status;
+ u16 status = port->status;
if (isicom_paranoia_check(port, tty->name, "isicom_ioctl"))
return -ENODEV;
-
+
return ((status & ISI_RTS) ? TIOCM_RTS : 0) |
((status & ISI_DTR) ? TIOCM_DTR : 0) |
((status & ISI_DCD) ? TIOCM_CAR : 0) |
@@ -1508,13 +1277,13 @@ static int isicom_tiocmget(struct tty_st
}
static int isicom_tiocmset(struct tty_struct *tty, struct file *file,
- unsigned int set, unsigned int clear)
+ unsigned int set, unsigned int clear)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
-
+ struct isi_port *port = tty->driver_data;
+
if (isicom_paranoia_check(port, tty->name, "isicom_ioctl"))
return -ENODEV;
-
+
if (set & TIOCM_RTS)
raise_rts(port);
if (set & TIOCM_DTR)
@@ -1526,46 +1295,46 @@ static int isicom_tiocmset(struct tty_st
drop_dtr(port);
return 0;
-}
+}
-static int isicom_set_serial_info(struct isi_port * port,
- struct serial_struct __user *info)
+static int isicom_set_serial_info(struct isi_port *port,
+ struct serial_struct __user *info)
{
struct serial_struct newinfo;
int reconfig_port;
- if(copy_from_user(&newinfo, info, sizeof(newinfo)))
+ if (copy_from_user(&newinfo, info, sizeof(newinfo)))
return -EFAULT;
-
- reconfig_port = ((port->flags & ASYNC_SPD_MASK) !=
- (newinfo.flags & ASYNC_SPD_MASK));
-
+
+ reconfig_port = ((port->flags & ASYNC_SPD_MASK) !=
+ (newinfo.flags & ASYNC_SPD_MASK));
+
if (!capable(CAP_SYS_ADMIN)) {
if ((newinfo.close_delay != port->close_delay) ||
- (newinfo.closing_wait != port->closing_wait) ||
- ((newinfo.flags & ~ASYNC_USR_MASK) !=
- (port->flags & ~ASYNC_USR_MASK)))
+ (newinfo.closing_wait != port->closing_wait) ||
+ ((newinfo.flags & ~ASYNC_USR_MASK) !=
+ (port->flags & ~ASYNC_USR_MASK)))
return -EPERM;
port->flags = ((port->flags & ~ ASYNC_USR_MASK) |
(newinfo.flags & ASYNC_USR_MASK));
- }
- else {
+ } else {
port->close_delay = newinfo.close_delay;
- port->closing_wait = newinfo.closing_wait;
- port->flags = ((port->flags & ~ASYNC_FLAGS) |
+ port->closing_wait = newinfo.closing_wait;
+ port->flags = ((port->flags & ~ASYNC_FLAGS) |
(newinfo.flags & ASYNC_FLAGS));
}
- if (reconfig_port) {
+
+ if (reconfig_port)
isicom_config_port(port);
- }
- return 0;
-}
-static int isicom_get_serial_info(struct isi_port * port,
- struct serial_struct __user *info)
+ return 0;
+}
+
+static int isicom_get_serial_info(struct isi_port *port,
+ struct serial_struct __user *info)
{
struct serial_struct out_info;
-
+
memset(&out_info, 0, sizeof(out_info));
/* out_info.type = ? */
out_info.line = port - isi_ports;
@@ -1575,15 +1344,15 @@ static int isicom_get_serial_info(struct
/* out_info.baud_base = ? */
out_info.close_delay = port->close_delay;
out_info.closing_wait = port->closing_wait;
- if(copy_to_user(info, &out_info, sizeof(out_info)))
+ if (copy_to_user(info, &out_info, sizeof(out_info)))
return -EFAULT;
return 0;
-}
+}
-static int isicom_ioctl(struct tty_struct * tty, struct file * filp,
- unsigned int cmd, unsigned long arg)
+static int isicom_ioctl(struct tty_struct *tty, struct file *filp,
+ unsigned int cmd, unsigned long arg)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
+ struct isi_port *port = tty->driver_data;
void __user *argp = (void __user *)arg;
int retval;
@@ -1599,131 +1368,133 @@ static int isicom_ioctl(struct tty_struc
if (!arg)
isicom_send_break(port, HZ/4);
return 0;
-
- case TCSBRKP:
+
+ case TCSBRKP:
retval = tty_check_change(tty);
if (retval)
return retval;
tty_wait_until_sent(tty, 0);
isicom_send_break(port, arg ? arg * (HZ/10) : HZ/4);
return 0;
-
+
case TIOCGSOFTCAR:
- return put_user(C_CLOCAL(tty) ? 1 : 0, (unsigned long __user *)argp);
-
+ return put_user(C_CLOCAL(tty) ? 1 : 0,
+ (unsigned long __user *)argp);
+
case TIOCSSOFTCAR:
if(get_user(arg, (unsigned long __user *) argp))
return -EFAULT;
tty->termios->c_cflag =
((tty->termios->c_cflag & ~CLOCAL) |
(arg ? CLOCAL : 0));
- return 0;
-
+ return 0;
+
case TIOCGSERIAL:
return isicom_get_serial_info(port, argp);
-
+
case TIOCSSERIAL:
return isicom_set_serial_info(port, argp);
-
+
default:
- return -ENOIOCTLCMD;
+ return -ENOIOCTLCMD;
}
return 0;
}
/* set_termios et all */
-static void isicom_set_termios(struct tty_struct * tty, struct termios * old_termios)
+static void isicom_set_termios(struct tty_struct *tty,
+ struct termios *old_termios)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
-
+ struct isi_port *port = tty->driver_data;
+
if (isicom_paranoia_check(port, tty->name, "isicom_set_termios"))
return;
-
+
if (tty->termios->c_cflag == old_termios->c_cflag &&
- tty->termios->c_iflag == old_termios->c_iflag)
+ tty->termios->c_iflag == old_termios->c_iflag)
return;
-
+
isicom_config_port(port);
-
+
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios->c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
- isicom_start(tty);
- }
+ isicom_start(tty);
+ }
}
/* throttle et all */
-static void isicom_throttle(struct tty_struct * tty)
+static void isicom_throttle(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
- struct isi_board * card = port->card;
-
+ struct isi_port *port = tty->driver_data;
+ struct isi_board *card = port->card;
+
if (isicom_paranoia_check(port, tty->name, "isicom_throttle"))
return;
-
+
/* tell the card that this port cannot handle any more data for now */
card->port_status &= ~(1 << port->channel);
outw(card->port_status, card->base + 0x02);
}
/* unthrottle et all */
-static void isicom_unthrottle(struct tty_struct * tty)
+static void isicom_unthrottle(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
- struct isi_board * card = port->card;
-
+ struct isi_port *port = tty->driver_data;
+ struct isi_board *card = port->card;
+
if (isicom_paranoia_check(port, tty->name, "isicom_unthrottle"))
return;
-
+
/* tell the card that this port is ready to accept more data */
card->port_status |= (1 << port->channel);
outw(card->port_status, card->base + 0x02);
}
/* stop et all */
-static void isicom_stop(struct tty_struct * tty)
+static void isicom_stop(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
+ struct isi_port *port = tty->driver_data;
if (isicom_paranoia_check(port, tty->name, "isicom_stop"))
return;
-
+
/* this tells the transmitter not to consider this port for
data output to the card. */
port->status &= ~ISI_TXOK;
}
/* start et all */
-static void isicom_start(struct tty_struct * tty)
+static void isicom_start(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
-
+ struct isi_port *port = tty->driver_data;
+
if (isicom_paranoia_check(port, tty->name, "isicom_start"))
return;
-
+
/* this tells the transmitter to consider this port for
data output to the card. */
port->status |= ISI_TXOK;
}
/* hangup et all */
-static void do_isicom_hangup(void * data)
+static void do_isicom_hangup(void *data)
{
- struct isi_port * port = (struct isi_port *) data;
- struct tty_struct * tty;
-
+ struct isi_port *port = data;
+ struct tty_struct *tty;
+
tty = port->tty;
if (tty)
tty_hangup(tty);
}
-static void isicom_hangup(struct tty_struct * tty)
+static void isicom_hangup(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
-
+ struct isi_port *port = tty->driver_data;
+
if (isicom_paranoia_check(port, tty->name, "isicom_hangup"))
return;
-
+
isicom_shutdown_port(port);
port->count = 0;
port->flags &= ~ASYNC_NORMAL_ACTIVE;
@@ -1732,342 +1503,558 @@ static void isicom_hangup(struct tty_str
}
/* flush_buffer et all */
-static void isicom_flush_buffer(struct tty_struct * tty)
+static void isicom_flush_buffer(struct tty_struct *tty)
{
- struct isi_port * port = (struct isi_port *) tty->driver_data;
- struct isi_board * card = port->card;
+ struct isi_port *port = tty->driver_data;
+ struct isi_board *card = port->card;
unsigned long flags;
-
+
if (isicom_paranoia_check(port, tty->name, "isicom_flush_buffer"))
return;
-
+
spin_lock_irqsave(&card->card_lock, flags);
port->xmit_cnt = port->xmit_head = port->xmit_tail = 0;
spin_unlock_irqrestore(&card->card_lock, flags);
-
+
wake_up_interruptible(&tty->write_wait);
tty_wakeup(tty);
}
+/*
+ * Driver init and deinit functions
+ */
-static int __devinit register_ioregion(void)
+static int __devinit isicom_register_ioregion(struct isi_board *board,
+ const unsigned int index)
{
- int count, done=0;
- for (count=0; count < BOARD_COUNT; count++ ) {
- if (isi_card[count].base)
- if (!request_region(isi_card[count].base,16,ISICOM_NAME)) {
- printk(KERN_DEBUG "ISICOM: I/O Region 0x%x-0x%x is busy. Card%d will be disabled.\n",
- isi_card[count].base,isi_card[count].base+15,count+1);
- isi_card[count].base=0;
- done++;
- }
+ if (!board->base)
+ return 0;
+
+ if (!request_region(board->base, 16, ISICOM_NAME)) {
+ printk(KERN_DEBUG "ISICOM: I/O Region 0x%x-0x%x is busy. "
+ "Card%d will be disabled.\n", board->base,
+ board->base + 15, index + 1);
+ return -EBUSY;
}
- return done;
+
+ return 0;
}
-static void unregister_ioregion(void)
+static void isicom_unregister_ioregion(struct isi_board *board,
+ const unsigned int index)
{
- int count;
- for (count=0; count < BOARD_COUNT; count++ )
- if (isi_card[count].base) {
- release_region(isi_card[count].base,16);
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: I/O Region 0x%x-0x%x released for Card%d.\n",isi_card[count].base,isi_card[count].base+15,count+1);
-#endif
- }
+ if (!board->base)
+ return;
+
+ release_region(board->base, 16);
+ board->base = 0;
+ pr_deb(KERN_DEBUG "ISICOM: I/O Region 0x%x-0x%x released for Card%d.\n",
+ board->base, board->base + 15, index + 1);
}
static struct tty_operations isicom_ops = {
- .open = isicom_open,
- .close = isicom_close,
- .write = isicom_write,
- .put_char = isicom_put_char,
- .flush_chars = isicom_flush_chars,
- .write_room = isicom_write_room,
+ .open = isicom_open,
+ .close = isicom_close,
+ .write = isicom_write,
+ .put_char = isicom_put_char,
+ .flush_chars = isicom_flush_chars,
+ .write_room = isicom_write_room,
.chars_in_buffer = isicom_chars_in_buffer,
- .ioctl = isicom_ioctl,
- .set_termios = isicom_set_termios,
- .throttle = isicom_throttle,
- .unthrottle = isicom_unthrottle,
- .stop = isicom_stop,
- .start = isicom_start,
- .hangup = isicom_hangup,
- .flush_buffer = isicom_flush_buffer,
- .tiocmget = isicom_tiocmget,
- .tiocmset = isicom_tiocmset,
+ .ioctl = isicom_ioctl,
+ .set_termios = isicom_set_termios,
+ .throttle = isicom_throttle,
+ .unthrottle = isicom_unthrottle,
+ .stop = isicom_stop,
+ .start = isicom_start,
+ .hangup = isicom_hangup,
+ .flush_buffer = isicom_flush_buffer,
+ .tiocmget = isicom_tiocmget,
+ .tiocmset = isicom_tiocmset,
};
-static int __devinit register_drivers(void)
+static int __devinit isicom_register_tty_driver(void)
{
- int error;
+ int error = -ENOMEM;
/* tty driver structure initialization */
isicom_normal = alloc_tty_driver(PORT_COUNT);
if (!isicom_normal)
- return -ENOMEM;
+ goto end;
- isicom_normal->owner = THIS_MODULE;
- isicom_normal->name = "ttyM";
- isicom_normal->devfs_name = "isicom/";
- isicom_normal->major = ISICOM_NMAJOR;
- isicom_normal->minor_start = 0;
- isicom_normal->type = TTY_DRIVER_TYPE_SERIAL;
- isicom_normal->subtype = SERIAL_TYPE_NORMAL;
- isicom_normal->init_termios = tty_std_termios;
- isicom_normal->init_termios.c_cflag =
- B9600 | CS8 | CREAD | HUPCL |CLOCAL;
- isicom_normal->flags = TTY_DRIVER_REAL_RAW;
+ isicom_normal->owner = THIS_MODULE;
+ isicom_normal->name = "ttyM";
+ isicom_normal->devfs_name = "isicom/";
+ isicom_normal->major = ISICOM_NMAJOR;
+ isicom_normal->minor_start = 0;
+ isicom_normal->type = TTY_DRIVER_TYPE_SERIAL;
+ isicom_normal->subtype = SERIAL_TYPE_NORMAL;
+ isicom_normal->init_termios = tty_std_termios;
+ isicom_normal->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL |
+ CLOCAL;
+ isicom_normal->flags = TTY_DRIVER_REAL_RAW;
tty_set_operations(isicom_normal, &isicom_ops);
-
- if ((error=tty_register_driver(isicom_normal))!=0) {
- printk(KERN_DEBUG "ISICOM: Couldn't register the dialin driver, error=%d\n",
- error);
+
+ if ((error = tty_register_driver(isicom_normal))) {
+ printk(KERN_DEBUG "ISICOM: Couldn't register the dialin "
+ "driver, error=%d\n", error);
put_tty_driver(isicom_normal);
- return error;
}
- return 0;
+end:
+ return error;
}
-static void unregister_drivers(void)
+static void isicom_unregister_tty_driver(void)
{
- int error = tty_unregister_driver(isicom_normal);
- if (error)
- printk(KERN_DEBUG "ISICOM: couldn't unregister normal driver error=%d.\n",error);
+ int error;
+
+ if ((error = tty_unregister_driver(isicom_normal)))
+ printk(KERN_DEBUG "ISICOM: couldn't unregister normal driver, "
+ "error=%d.\n", error);
+
put_tty_driver(isicom_normal);
}
-static int __devinit register_isr(void)
+static int __devinit isicom_register_isr(struct isi_board *board,
+ const unsigned int index)
{
- int count, done=0;
- unsigned long irqflags;
+ unsigned long irqflags = SA_INTERRUPT;
+ int retval;
- for (count=0; count < BOARD_COUNT; count++ ) {
- if (isi_card[count].base) {
- irqflags = (isi_card[count].isa == YES) ?
- SA_INTERRUPT :
- (SA_INTERRUPT | SA_SHIRQ);
-
- if (request_irq(isi_card[count].irq,
- isicom_interrupt,
- irqflags,
- ISICOM_NAME, &isi_card[count])) {
-
- printk(KERN_WARNING "ISICOM: Could not"
- " install handler at Irq %d."
- " Card%d will be disabled.\n",
- isi_card[count].irq, count+1);
+ if (!board->base)
+ return 0;
- release_region(isi_card[count].base,16);
- isi_card[count].base=0;
- }
- else
- done++;
- }
+ if (board->isa == NO)
+ irqflags |= SA_SHIRQ;
+
+ retval = request_irq(board->irq, isicom_interrupt, irqflags,
+ ISICOM_NAME, board);
+ if (retval < 0) {
+ printk(KERN_WARNING "ISICOM: Could not install handler at Irq "
+ "%d. Card%d will be disabled.\n", board->irq,
+ index + 1);
+ return retval;
}
- return done;
+
+ return 0;
}
-static void __exit unregister_isr(void)
+static void isicom_unregister_isr(struct isi_board *board)
{
- int count;
+ if (board->base)
+ free_irq(board->irq, board);
+}
- for (count=0; count < BOARD_COUNT; count++ ) {
- if (isi_card[count].base)
- free_irq(isi_card[count].irq, &isi_card[count]);
- }
+static inline int __devinit WaitTillCardIsFree(u16 base)
+{
+ int count = 0;
+
+ while ((!(inw(base + 0xe) & 0x1)) && (count++ < 1000))
+ msleep(1);
+
+ return !(inw(base + 0xe) & 0x1);
}
-static int __devinit isicom_init(void)
+static int __devinit reset_card(struct isi_board *board,
+ const unsigned int card, unsigned int *signature)
{
- int card, channel, base;
- struct isi_port * port;
- unsigned long page;
-
- if (!tmp_buf) {
- page = get_zeroed_page(GFP_KERNEL);
- if (!page) {
-#ifdef ISICOM_DEBUG
- printk(KERN_DEBUG "ISICOM: Couldn't allocate page for tmp_buf.\n");
-#else
- printk(KERN_ERR "ISICOM: Not enough memory...\n");
-#endif
- return 0;
- }
- tmp_buf = (unsigned char *) page;
- }
-
- if (!register_ioregion())
- {
- printk(KERN_ERR "ISICOM: All required I/O space found busy.\n");
- free_page((unsigned long)tmp_buf);
- return 0;
+ u16 base = board->base;
+ unsigned int portcount = 0;
+ int retval = 0;
+
+ printk(KERN_DEBUG "ISILoad:Resetting Card%d at 0x%x\n", card + 1, base);
+
+ inw(base + 0x8);
+
+ mdelay(10);
+
+ outw(0, base + 0x8); /* Reset */
+
+ msleep(3000);
+
+ *signature = inw(base + 0x4) & 0xff;
+
+ if (board->isa == YES) {
+ if (!(inw(base + 0xe) & 0x1) || (inw(base + 0x2))) {
+ pr_deb(KERN_DEBUG "base+0x2=0x%x, base+0xe=0x%x",
+ inw(base + 0x2), inw(base + 0xe));
+ printk(KERN_ERR "ISILoad:ISA Card%d reset failure "
+ "(Possible bad I/O Port Address 0x%x).\n",
+ card + 1, base);
+ retval = -EIO;
+ goto end;
+ }
+ } else {
+ portcount = inw(base + 0x2);
+ if (!(inw(base + 0xe) & 0x1) || ((portcount != 0) &&
+ (portcount != 4) && (portcount != 8))) {
+ pr_deb("\nbase+0x2=0x%x , base+0xe=0x%x",
+ inw(base + 0x2), inw(base + 0xe));
+ printk("\nISILoad:PCI Card%d reset failure (Possible "
+ "bad I/O Port Address 0x%x).\n", card + 1,
+ base);
+ retval = -EIO;
+ goto end;
+ }
}
- if (register_drivers())
- {
- unregister_ioregion();
- free_page((unsigned long)tmp_buf);
- return 0;
+
+ switch (*signature) {
+ case 0xa5:
+ case 0xbb:
+ case 0xdd:
+ board->port_count = (board->isa == NO && portcount == 4) ? 4 :
+ 8;
+ board->shift_count = 12;
+ break;
+ case 0xcc:
+ board->port_count = 16;
+ board->shift_count = 11;
+ break;
+ default:
+ printk(KERN_WARNING "ISILoad:Card%d reset failure (Possible "
+ "bad I/O Port Address 0x%x).\n", card + 1, base);
+ pr_deb(KERN_DEBUG "Sig=0x%x\n", signature);
+ retval = -EIO;
+ }
+ printk(KERN_INFO "-Done\n");
+
+end:
+ return retval;
+}
+
+static int __devinit load_firmware(struct isi_board *board,
+ const unsigned int index, const unsigned int signature)
+{
+ int retval = -EIO;
+ unsigned int a;
+ char *name;
+ u8 *data;
+ u16 word_count, status, base = board->base;
+ const struct firmware *fw;
+ struct stframe {
+ u16 addr;
+ u16 count;
+ u8 data[0];
+ } *frame;
+
+ switch (signature) {
+ case 0xa5:
+ name = "isi608.bin";
+ break;
+ case 0xbb:
+ name = "isi608em.bin";
+ break;
+ case 0xcc:
+ name = "isi616em.bin";
+ break;
+ case 0xdd:
+ name = "isi4608.bin";
+ break;
+ case 0xee:
+ name = "isi4616.bin";
+ break;
+ default:
+ printk(KERN_ERR "Unknown signature.\n");
+ goto end;
}
- if (!register_isr())
- {
- unregister_drivers();
- /* ioports already uregistered in register_isr */
- free_page((unsigned long)tmp_buf);
- return 0;
+
+ retval = request_firmware(&fw, name, &board->device);
+ if (retval)
+ goto end;
+
+ for (frame = (struct stframe*)fw->data;
+ frame < (struct stframe*)(fw->data + fw->size);
+ frame++) {
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ outw(0xf0, base); /* start upload sequence */
+ outw(0x00, base);
+ outw(frame->addr, base); /* lsb of address */
+
+ word_count = frame->count / 2 + frame->count % 2;
+ outw(word_count, base);
+ InterruptTheCard(base);
+
+ udelay(100); /* 0x2f */
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ if ((status = inw(base + 0x4)) != 0) {
+ printk(KERN_WARNING "ISILoad:Card%d rejected load "
+ "header:\nAddress:0x%x \nCount:0x%x \n"
+ "Status:0x%x \n", index + 1, frame->addr,
+ frame->count, status);
+ goto errrelfw;
+ }
+ outsw(base, frame->data, word_count);
+
+ InterruptTheCard(base);
+
+ udelay(50); /* 0x0f */
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ if ((status = inw(base + 0x4)) != 0) {
+ printk(KERN_ERR "ISILoad:Card%d got out of sync.Card "
+ "Status:0x%x\n", index + 1, status);
+ goto errrelfw;
+ }
}
-
- memset(isi_ports, 0, sizeof(isi_ports));
- for (card = 0; card < BOARD_COUNT; card++) {
- port = &isi_ports[card * 16];
- isi_card[card].ports = port;
- spin_lock_init(&isi_card[card].card_lock);
- base = isi_card[card].base;
- for (channel = 0; channel < 16; channel++, port++) {
- port->magic = ISICOM_MAGIC;
- port->card = &isi_card[card];
- port->channel = channel;
- port->close_delay = 50 * HZ/100;
- port->closing_wait = 3000 * HZ/100;
- INIT_WORK(&port->hangup_tq, do_isicom_hangup, port);
- INIT_WORK(&port->bh_tqueue, isicom_bottomhalf, port);
- port->status = 0;
- init_waitqueue_head(&port->open_wait);
- init_waitqueue_head(&port->close_wait);
- /* . . . */
- }
- }
-
- return 1;
+
+ retval = -EIO;
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ outw(0xf2, base);
+ outw(0x800, base);
+ outw(0x0, base);
+ outw(0x0, base);
+ InterruptTheCard(base);
+ outw(0x0, base + 0x4); /* for ISI4608 cards */
+
+/* XXX: should we test it by reading it back and comparing with original like
+ * in load firmware package? */
+ for (frame = (struct stframe*)fw->data;
+ frame < (struct stframe*)(fw->data + fw->size);
+ frame++) {
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ outw(0xf1, base); /* start download sequence */
+ outw(0x00, base);
+ outw(frame->addr, base); /* lsb of address */
+
+ word_count = (frame->count >> 1) + frame->count % 2;
+ outw(word_count + 1, base);
+ InterruptTheCard(base);
+
+ udelay(50); /* 0xf */
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ if ((status = inw(base + 0x4)) != 0) {
+ printk(KERN_WARNING "ISILoad:Card%d rejected verify "
+ "header:\nAddress:0x%x \nCount:0x%x\nStatus: "
+ "0x%x \n", index + 1, frame->addr, frame->count,
+ status);
+ goto errrelfw;
+ }
+
+ data = kmalloc(word_count * 2, GFP_KERNEL);
+ inw(base);
+ insw(base, data, word_count);
+ InterruptTheCard(base);
+
+ for (a = 0; a < frame->count; a++)
+ if (data[a] != frame->data[a]) {
+ kfree(data);
+ printk(KERN_ERR "ISILoad:Card%d, firmware "
+ "upload failed\n", index + 1);
+ goto errrelfw;
+ }
+ kfree(data);
+
+ udelay(50); /* 0xf */
+
+ if (WaitTillCardIsFree(base))
+ goto errrelfw;
+
+ if ((status = inw(base + 0x4)) != 0) {
+ printk(KERN_ERR "ISILoad:Card%d verify got out of "
+ "sync. Card Status:0x%x\n", index + 1, status);
+ goto errrelfw;
+ }
+ }
+
+ board->status |= FIRMWARE_LOADED;
+ retval = 0;
+
+errrelfw:
+ release_firmware(fw);
+end:
+ return retval;
}
/*
* Insmod can set static symbols so keep these static
*/
-
static int io[4];
static int irq[4];
+static int card;
-MODULE_AUTHOR("MultiTech");
-MODULE_DESCRIPTION("Driver for the ISI series of cards by MultiTech");
-MODULE_LICENSE("GPL");
-module_param_array(io, int, NULL, 0);
-MODULE_PARM_DESC(io, "I/O ports for the cards");
-module_param_array(irq, int, NULL, 0);
-MODULE_PARM_DESC(irq, "Interrupts for the cards");
+static int __devinit isicom_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ unsigned int ioaddr, signature, index;
+ int retval = -EPERM;
+ u8 pciirq;
+ struct isi_board *board = NULL;
+
+ if (card >= BOARD_COUNT)
+ goto err;
+
+ ioaddr = pci_resource_start(pdev, 3);
+ /* i.e at offset 0x1c in the PCI configuration register space. */
+ pciirq = pdev->irq;
+ printk(KERN_INFO "ISI PCI Card(Device ID 0x%x)\n", ent->device);
+
+ /* allot the first empty slot in the array */
+ for (index = 0; index < BOARD_COUNT; index++)
+ if (isi_card[index].base == 0) {
+ board = &isi_card[index];
+ break;
+ }
+
+ board->base = ioaddr;
+ board->irq = pciirq;
+ board->isa = NO;
+ board->device = pdev->dev;
+ card++;
+
+ retval = isicom_register_ioregion(board, index);
+ if (retval < 0)
+ goto err;
+
+ retval = isicom_register_isr(board, index);
+ if (retval < 0)
+ goto errunrr;
+
+ retval = reset_card(board, index, &signature);
+ if (retval < 0)
+ goto errunri;
+
+ retval = load_firmware(board, index, signature);
+ if (retval < 0)
+ goto errunri;
+
+ return 0;
+
+errunri:
+ isicom_unregister_isr(board);
+errunrr:
+ isicom_unregister_ioregion(board, index);
+err:
+ board->base = 0;
+ return retval;
+}
+
+static void __devexit isicom_remove(struct pci_dev *pdev)
+{
+ unsigned int idx;
+
+ for (idx = 0; idx < BOARD_COUNT; idx++)
+ if (isi_card[idx].base == pci_resource_start(pdev, 3))
+ break;
+
+ if (idx == BOARD_COUNT)
+ return;
+
+ isicom_unregister_isr(&isi_card[idx]);
+ isicom_unregister_ioregion(&isi_card[idx], idx);
+}
static int __devinit isicom_setup(void)
{
- struct pci_dev *dev = NULL;
- int retval, card, idx, count;
- unsigned char pciirq;
- unsigned int ioaddr;
-
+ int retval, idx, channel;
+ struct isi_port *port;
+
card = 0;
- for(idx=0; idx < BOARD_COUNT; idx++) {
- if (io[idx]) {
- isi_card[idx].base=io[idx];
- isi_card[idx].irq=irq[idx];
- isi_card[idx].isa=YES;
- card++;
- }
- else {
- isi_card[idx].base = 0;
- isi_card[idx].irq = 0;
- }
- }
-
- for (idx=0 ;idx < card; idx++) {
- if (!((isi_card[idx].irq==2)||(isi_card[idx].irq==3)||
- (isi_card[idx].irq==4)||(isi_card[idx].irq==5)||
- (isi_card[idx].irq==7)||(isi_card[idx].irq==10)||
- (isi_card[idx].irq==11)||(isi_card[idx].irq==12)||
- (isi_card[idx].irq==15))) {
-
- if (isi_card[idx].base) {
- printk(KERN_ERR "ISICOM: Irq %d unsupported. Disabling Card%d...\n",
- isi_card[idx].irq, idx+1);
- isi_card[idx].base=0;
- card--;
- }
- }
- }
-
- if (card < BOARD_COUNT) {
- for (idx=0; idx < DEVID_COUNT; idx++) {
- dev = NULL;
- for (;;){
- if (!(dev = pci_find_device(VENDOR_ID, isicom_pci_tbl[idx].device, dev)))
- break;
- if (card >= BOARD_COUNT)
- break;
-
- if (pci_enable_device(dev))
- break;
+ memset(isi_ports, 0, sizeof(isi_ports));
- /* found a PCI ISI card! */
- ioaddr = pci_resource_start (dev, 3); /* i.e at offset 0x1c in the
- * PCI configuration register
- * space.
- */
- pciirq = dev->irq;
- printk(KERN_INFO "ISI PCI Card(Device ID 0x%x)\n", isicom_pci_tbl[idx].device);
- /*
- * allot the first empty slot in the array
- */
- for (count=0; count < BOARD_COUNT; count++) {
- if (isi_card[count].base == 0) {
- isi_card[count].base = ioaddr;
- isi_card[count].irq = pciirq;
- isi_card[count].isa = NO;
- card++;
- break;
- }
- }
- }
- if (card >= BOARD_COUNT) break;
+ for(idx = 0; idx < BOARD_COUNT; idx++) {
+ port = &isi_ports[idx * 16];
+ isi_card[idx].ports = port;
+ spin_lock_init(&isi_card[idx].card_lock);
+ for (channel = 0; channel < 16; channel++, port++) {
+ port->magic = ISICOM_MAGIC;
+ port->card = &isi_card[idx];
+ port->channel = channel;
+ port->close_delay = 50 * HZ/100;
+ port->closing_wait = 3000 * HZ/100;
+ INIT_WORK(&port->hangup_tq, do_isicom_hangup, port);
+ INIT_WORK(&port->bh_tqueue, isicom_bottomhalf, port);
+ port->status = 0;
+ init_waitqueue_head(&port->open_wait);
+ init_waitqueue_head(&port->close_wait);
+ /* . . . */
}
- }
-
- if (!(isi_card[0].base || isi_card[1].base || isi_card[2].base || isi_card[3].base)) {
- printk(KERN_ERR "ISICOM: No valid card configuration. Driver cannot be initialized...\n");
- return -EIO;
- }
- retval = misc_register(&isiloader_device);
+ isi_card[idx].base = 0;
+ isi_card[idx].irq = 0;
+
+ if (!io[idx])
+ continue;
+
+ if (irq[idx] == 2 || irq[idx] == 3 || irq[idx] == 4 ||
+ irq[idx] == 5 || irq[idx] == 7 ||
+ irq[idx] == 10 || irq[idx] == 11 ||
+ irq[idx] == 12 || irq[idx] == 15) {
+ printk(KERN_ERR "ISICOM: ISA not supported yet.\n");
+ return -EIO;
+/* isi_card[idx].base = io[idx];
+ isi_card[idx].irq = irq[idx];
+ isi_card[idx].isa = YES;
+ FIXME: which device for request_firmware use? if you know, uncomment this and
+ delete printk and return
+ isi_card[idx].device = ???;
+ card++;*/
+ } else
+ printk(KERN_ERR "ISICOM: Irq %d unsupported. "
+ "Disabling Card%d...\n", irq[idx], idx + 1);
+ }
+
+ retval = isicom_register_tty_driver();
+ if (retval < 0)
+ goto error;
+
+ retval = pci_register_driver(&isicom_driver);
if (retval < 0) {
- printk(KERN_ERR "ISICOM: Unable to register firmware loader driver.\n");
- return retval;
- }
-
- if (!isicom_init()) {
- if (misc_deregister(&isiloader_device))
- printk(KERN_ERR "ISICOM: Unable to unregister Firmware Loader driver\n");
- return -EIO;
+ printk(KERN_ERR "ISICOM: Unable to register pci driver.\n");
+ goto error;
}
-
+
init_timer(&tx);
tx.expires = jiffies + 1;
tx.data = 0;
tx.function = isicom_tx;
re_schedule = 1;
add_timer(&tx);
-
+
return 0;
+
+error:
+ return retval;
}
static void __exit isicom_exit(void)
{
+ unsigned int index = 0;
+
re_schedule = 0;
- /* FIXME */
- msleep(1000);
- unregister_isr();
- unregister_drivers();
- unregister_ioregion();
- if(tmp_buf)
- free_page((unsigned long)tmp_buf);
- if (misc_deregister(&isiloader_device))
- printk(KERN_ERR "ISICOM: Unable to unregister Firmware Loader driver\n");
+
+ while (re_schedule != 2 && index++ < 100)
+ msleep(10);
+
+ pci_unregister_driver(&isicom_driver);
+ isicom_unregister_tty_driver();
+
+ for (index = 0; index < BOARD_COUNT; index++) {
+ isicom_unregister_isr(&isi_card[index]);
+ isicom_unregister_ioregion(&isi_card[index], index);
+ }
}
module_init(isicom_setup);
module_exit(isicom_exit);
+
+MODULE_AUTHOR("MultiTech");
+MODULE_DESCRIPTION("Driver for the ISI series of cards by MultiTech");
+MODULE_LICENSE("GPL");
+module_param_array(io, int, NULL, 0);
+MODULE_PARM_DESC(io, "I/O ports for the cards");
+module_param_array(irq, int, NULL, 0);
+MODULE_PARM_DESC(irq, "Interrupts for the cards");
diff --git a/include/linux/isicom.h b/include/linux/isicom.h
--- a/include/linux/isicom.h
+++ b/include/linux/isicom.h
@@ -5,46 +5,12 @@
/*#define ISICOM_DEBUG_DTR_RTS*/
-/*
- * Firmware Loader definitions ...
- */
-
-#define __MultiTech ('M'<<8)
-#define MIOCTL_LOAD_FIRMWARE (__MultiTech | 0x01)
-#define MIOCTL_READ_FIRMWARE (__MultiTech | 0x02)
-#define MIOCTL_XFER_CTRL (__MultiTech | 0x03)
-#define MIOCTL_RESET_CARD (__MultiTech | 0x04)
-
-#define DATA_SIZE 16
-
-typedef struct {
- unsigned short exec_segment;
- unsigned short exec_addr;
-} exec_record;
-
-typedef struct {
- int board; /* Board to load */
- unsigned short addr;
- unsigned short count;
-} bin_header;
-
-typedef struct {
- int board; /* Board to load */
- unsigned short addr;
- unsigned short count;
- unsigned short segment;
- unsigned char bin_data[DATA_SIZE];
-} bin_frame;
-
#ifdef __KERNEL__
#define YES 1
#define NO 0
-#define ISILOAD_MISC_MINOR 155 /* /dev/isctl */
-#define ISILOAD_NAME "ISILoad"
-
-/*
+/*
* ISICOM Driver definitions ...
*
*/
@@ -66,9 +32,9 @@ typedef struct {
#define ISICOM_CMAJOR 113 /* callout */
#define ISICOM_MAGIC (('M' << 8) | 'T')
-#define WAKEUP_CHARS 256 /* hard coded for now */
-#define TX_SIZE 254
-
+#define WAKEUP_CHARS 256 /* hard coded for now */
+#define TX_SIZE 254
+
#define BOARD_COUNT 4
#define PORT_COUNT (BOARD_COUNT*16)
@@ -98,18 +64,15 @@ typedef struct {
#define ISICOM_INITIATE_XONXOFF 0x04
#define ISICOM_RESPOND_XONXOFF 0x08
-#define InterruptTheCard(base) (outw(0,(base)+0xc))
-#define ClearInterrupt(base) (inw((base)+0x0a))
-
#define BOARD(line) (((line) >> 4) & 0x3)
/* isi kill queue bitmap */
-
+
#define ISICOM_KILLTX 0x01
#define ISICOM_KILLRX 0x02
/* isi_board status bitmap */
-
+
#define FIRMWARE_LOADED 0x0001
#define BOARD_ACTIVE 0x0002
@@ -123,8 +86,8 @@ typedef struct {
#define ISI_RTS 0x0200
-#define ISI_TXOK 0x0001
-
+#define ISI_TXOK 0x0001
+
#endif /* __KERNEL__ */
#endif /* ISICOM_H */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
| |
 |