This is a processor idle module for AMD SMP 760MP(X) based systems.
The patch was originally written by Tony Lindgren and has been around
since 2002. It enables C2 mode on AMD SMP systems and thus saves
about 70 - 90 W of energy in the idle mode compared to the default idle
mode. The idle function has been rewritten and is now free of locking
issues and is independent from the number of CPUs. The impact
from this module on the system clock and on i/o transfer rates has
been reduced.
This patch can also be found at
http://www.sommrey.de/amd76x_pm/amd_76x_pm-2.6.13-1.patch
Signed-off-by: Joerg Sommrey <[email protected]>
diff -Nru linux-2.6.13/Documentation/amd76x_pm.txt linux-2.6.13-jo/Documentation/amd76x_pm.txt
--- linux-2.6.13/Documentation/amd76x_pm.txt 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.13-jo/Documentation/amd76x_pm.txt 2005-09-01 21:50:12.000000000 +0200
@@ -0,0 +1,326 @@
+ ACPI style power management for SMP AMD-760MP(X) based systems
+ ==============================================================
+
+For use until the ACPI project catches up. :-)
+
+Using this module saves about 70 - 90W of energy in the idle mode compared
+to the default idle mode. Waking up from the idle mode is fast to keep the
+system response time good. Currently no CPU load calculation is done, the
+system exits the idle mode after every C2 call.
+
+NOTE: Currently there's a bug somewhere where the reading the
+ P_LVL2 for the first time causes the system to sleep instead of
+ idling. This means that you need to hit the power button once to
+ wake the system after loading the module for the first time after
+ reboot. After that the system idles as supposed.
+ (Only observed on Tony's system.)
+
+
+Influenced by Vcool, and LVCool. Rewrote everything from scratch to
+use the PCI features in Linux, and to support SMP systems.
+
+Currently tested amongst others on a TYAN S2460 (760MP) system (Tony), an
+ASUS A7M266-D (760MPX) system (Johnathan) and a TYAN S2466 (760MPX)
+system (Jo). Adding support for other Athlon SMP or single processor
+systems should be easy if desired.
+
+The file /sys/devices/pci0000:00/0000:00:00.0/C2_cnt shows the number of
+C2 calls since module load.
+
+There are some parameters for tuning the behaviour of amd76x_pm:
+lazy_idle, spin_idle, watch_irqs, watch_int and min_C1
+
+lazy_idle and spin_idle are closely related:
+
+- lazy_idle defines the number of idle calls into amd76x_smp_idle that are
+ needed to *enable* C2 mode. This parameter is the maximum loop counter
+ for an outer loop with interrupts enabled that guarantees low latencies.
+ The default for lazy_idle is 512.
+
+- spin_idle defines the maximum number of spin cycles in an inner idle loop
+ where one CPU waits for all others to get into C2-enabled mode. When all
+ CPUs are in C2-enable mode they (more ore less) simultaneously *enter* C2
+ mode. In this inner loop interrupts are disabled. The loop is left
+ immediatly if there is something waiting to be scheduled. The default
+ for spin_idle is 2*lazy_idle.
+
+lazy_idle and spin_idle define a "rubber measure" for the idling
+behaviour: lazy_idle defines the minimum "idling" needed to enter C2 and
+spin_idle defines when to give up.
+
+Low values for lazy_idle and high values for spin_idle give better
+cooling. Higher values for lazy_idle simply give less cooling. spin_idle
+is a kind of emergency break to leave C2-enable mode if CPUs don't
+synchronize.
+
+Interrupts are disabled in C2 mode. The CPUs are woken up by timer
+interrups or by NMIs. This causes a high interrupt latency for other
+interrupts that leads to a significant reduction in io or network
+throughput. There has been introduced a "irq rate watcher" to reduce
+this effect. If the irq rate watcher detects that an interrupt has a
+rate above a given limit, C2 idling is disabled and a low latency C1
+idling mode is used instead. The parameters watch_irqs, watch_int and
+min_C1 control this irq rate watcher:
+
+- watch_irqs defines which interrupts are to be watched and optionally
+ at which interrupt rate C2 mode shall be disabled. The syntax for
+ watch_irqs is irq1[:rate1],irq2[:rate2],... The rate is measured in
+ interrupts per second and defaults to 128. There is no default for
+ watch_irqs. To enable the irq rate watcher you must specify this
+ parameter. Enter the interrupts used by disk controllers or network
+ adapters here.
+
+- watch_int defines the time interval (in milliseconds) at which the
+ interrupt rate is checked. Too low values may result in an overhead
+ and too high values cause the C1 mode to "kick in" later. The default
+ for watch_int is 1 second.
+
+- min_C1 defines the mininum number of check intervals with low
+ interrupt rates that are needed to leave the forced C1 mode.
+
+All parameters lazy_idle, spin_idle, watch_irqs and watch_int may be
+given as module parameters to amd76x_pm. Furthermore, they may be
+queried or changed via their sysfs entries in
+/sys/module/amd76x_pm/parameters. (The file location in sysfs has
+changed from earlier versions!)
+
+Setting watch_int to zero or removing all interrupts from watch_irqs
+causes the irq rate watcher to stop. The module needs to be reloaded to
+start the watcher again.
+
+NB: In the past there was a major impact from amd76x_pm on the system
+clock stability. At least on my box this effect has been reduced
+noticable. This is caused by two changes:
+
+- The redesign of the idle function lead to a reduced time spent in
+ amd76x_smp_idle() and this propably caused lower latencies.
+
+- The introduction of the irq rate watcher significantly reduced
+ latencies under load.
+
+Some hints on tuning lazy_idle and spin_idle:
+Watch the rate of C2 calls per second. Anything below HZ seems to be
+completely useless. Start with a moderate low value for lazy_idle, e.g.
+2^5 and a very high value for spin_idle, e.g. 2^20. Then double lazy_idle
+until you see a significant increase in core temperature or C2 rate.
+Go back to the last "good" value. Then halve spin_idle until you see
+a decrease in C2 rate or a raising core temperature again and go back
+to the previous value. There's a small program c2rate.c attached at the
+end of this file that you may use to watch the C2 rate. The rtc driver
+must be enabled to use it.
+
+There is an -extra patch available that adds some optional features:
+- C3 idling: this works but is not well tested.
+- normal throttling: untested for a long time.
+- Power On Suspend: very experimental and untested.
+
+This software is licensed under GNU General Public License Version 2
+as specified in file COPYING in the Linux kernel source tree main
+directory.
+
+Copyright (C) 2002 - 2005 Johnathan Hicks <[email protected]>
+ Tony Lindgren <[email protected]>
+ Joerg Sommrey <[email protected]>
+
+History:
+
+ 20020702 - amd-smp-idle: Tony Lindgren <[email protected]>
+Influenced by Vcool, and LVCool. Rewrote everything from scratch to
+use the PCI features in Linux, and to support SMP systems. Provides
+C2 idling on SMP AMD-760MP systems.
+
+ 20020722: JH
+ I adapted Tony's code for the AMD-765/766 southbridge and adapted it
+ according to the AMD-768 data sheet to provide the same capability for
+ SMP AMD-760MPX systems. Posted to acpi-devel list.
+
+ 20020722: Alan Cox
+ Replaces non-functional amd76x_pm code in -ac tree.
+
+ 20020730: JH
+ Added ability to do normal throttling (the non-thermal kind), C3 idling
+ and Power On Suspend (S1 sleep). It would be very easy to tie swsusp
+ into activate_amd76x_SLP(). C3 idling doesn't happen yet; see my note
+ in amd76x_smp_idle(). I've noticed that when NTH and idling are both
+ enabled, my hardware locks and requires a hard reset, so I have
+ #ifndefed around the idle loop setting to prevent this. POS locks it up
+ too, both ought to be fixable. I've also noticed that idling and NTH
+ make some interference that is picked up by the onboard sound chip on
+ my ASUS A7M266-D motherboard.
+
+ 20030601: Pasi Savolainen
+ Simple port to 2.5
+ Added sysfs interface for making nice graphs with mrtg.
+ Look for /sys/devices/pci0/00:00.0/C2_cnt & lazy_idle (latter writable)
+
+ 20050601: Joerg Sommrey (jo)
+ 2.6 stuff
+ redesigned amd76x_smp_idle. The algorithm is basically the same
+ but the implementation has changed. This part is now independent
+ from the number of CPUs and data is locked against concurrent
+ updates from different CPUs.
+ use _smp_processor_id()
+ use cpu_idle_wait()
+ NTH and POS code not touched and not tested.
+
+ 20050621: jo
+ separated C3, NTH and POS code into extra patch
+
+ 20050812: jo
+ rewritten amd76x_smp_idle completely. It's much simpler now but
+ does a good job - the KISS approach. Introduced a new tunable
+ spin_idle.
+
+ 20050819: jo
+ new irq rate watcher task that forces C1-idling if irq-rate exceeds a
+ given limit.
+
+ 20050820: jo
+ make all modules parameters r/w in sysfs.
+
+ 20050830: jo
+ some API changes for 2.6.13
+
+TODO: Thermal throttling (TTH).
+ /proc interface for normal throttling level.
+ /proc interface for POS.
+
+---- c2rate.c ---- snip here ----------------------------------------
+/* c2rate.c
+ * usage: c2rate [interval]
+ * interval is the time in seconds between two calculations and defaults
+ * to 16
+ * You may #define C3 if you're playing with C3 mode.
+ */
+#include <stdlib.h>
+#include <stdio.h>
+#include <linux/rtc.h>
+#include <sys/ioctl.h>
+#include <sys/time.h>
+#include <sys/types.h>
+#include <fcntl.h>
+#include <unistd.h>
+#include <errno.h>
+
+#define C2_CNT "/sys/devices/pci0000:00/0000:00:00.0/C2_cnt"
+#define C3_CNT "/sys/devices/pci0000:00/0000:00:00.0/C3_cnt"
+// #define C3
+int fd;
+
+void
+disable_rtc(void) {
+ int retval;
+ /* Disable alarm interrupts */
+ retval = ioctl(fd, RTC_UIE_OFF, 0);
+ if (retval == -1) {
+ perror("ioctl(RTC_UIE_OFF)");
+ _exit(errno);
+ }
+ close(fd);
+}
+
+int
+main(int argc, char **argv)
+{
+ int retval;
+ unsigned long data;
+ char idlebuffer[64];
+ int idlefd;
+ ssize_t bytes;
+ unsigned long lastcount;
+ unsigned long irqcount;
+ unsigned long c2_old, c2_new;
+#ifdef C3
+ unsigned long c3_old, c3_new;
+#endif
+ int rate = 0;
+ int firstloop = 1;
+
+ if(argc > 1)
+ rate = atoi(argv[1]);
+ if (rate <= 0)
+ rate = 16;
+
+ fd = open ("/dev/rtc", O_RDONLY);
+
+ if (fd == -1) {
+ perror("/dev/rtc");
+ exit(errno);
+ }
+
+ /* Set the alarm to every second */
+
+ retval = ioctl(fd, RTC_UIE_ON, 0);
+ if (retval == -1) {
+ perror("ioctl(RTC_UIE_ON)");
+ exit(errno);
+ }
+ atexit(disable_rtc);
+
+ irqcount = 0;
+ while (1) {
+ /* This blocks until the alarm ring causes an interrupt */
+ retval = read(fd, &data, sizeof data);
+ if (retval == -1) {
+ perror("read");
+ exit(errno);
+ }
+ if (firstloop) {
+ idlebuffer[0] = '\0';
+ idlefd = open(C2_CNT, O_RDONLY);
+ if (idlefd != -1) {
+ bytes = read(idlefd, idlebuffer, sizeof idlebuffer);
+ close(idlefd);
+ idlebuffer[bytes] = '\0';
+ }
+ c2_old = strtoul(idlebuffer, NULL, 10);
+#ifdef C3
+ idlebuffer[0] = '\0';
+ idlefd = open(C3_CNT, O_RDONLY);
+ if (idlefd != -1) {
+ bytes = read(idlefd, idlebuffer, sizeof idlebuffer);
+ close(idlefd);
+ idlebuffer[bytes] = '\0';
+ }
+ c3_old = strtoul(idlebuffer, NULL, 10);
+#endif
+ firstloop = 0;
+ continue;
+ }
+ lastcount = data >> 8;
+ irqcount += lastcount;
+
+ if (irqcount >= rate) {
+ idlebuffer[0] = '\0';
+ idlefd = open(C2_CNT, O_RDONLY);
+ if (idlefd != -1) {
+ bytes = read(idlefd, idlebuffer, sizeof idlebuffer);
+ close(idlefd);
+ idlebuffer[bytes] = '\0';
+ }
+ c2_new = strtoul(idlebuffer, NULL, 10);
+#ifdef C3
+ idlebuffer[0] = '\0';
+ idlefd = open(C3_CNT, O_RDONLY);
+ if (idlefd != -1) {
+ bytes = read(idlefd, idlebuffer, sizeof idlebuffer);
+ close(idlefd);
+ idlebuffer[bytes] = '\0';
+ }
+ c3_new = strtoul(idlebuffer, NULL, 10);
+ printf("%lu\t%lu\n", (c2_new - c2_old) / irqcount,
+ (c3_new - c3_old) / irqcount);
+ c3_old = c3_new;
+#else
+ printf("%lu\n", (c2_new - c2_old) / irqcount);
+#endif
+ c2_old = c2_new;
+ irqcount = 0;
+ }
+
+ }
+
+ return 0;
+
+} /* end main */
+---- c2rate.c ---- snip here ----------------------------------------
diff -Nru linux-2.6.13/drivers/acpi/Kconfig linux-2.6.13-jo/drivers/acpi/Kconfig
--- linux-2.6.13/drivers/acpi/Kconfig 2005-08-29 17:18:56.000000000 +0200
+++ linux-2.6.13-jo/drivers/acpi/Kconfig 2005-08-29 21:03:50.000000000 +0200
@@ -365,4 +365,18 @@
$>modprobe acpi_memhotplug
endif # ACPI
+config AMD76X_PM
+ tristate "AMD76x Native Power Management support"
+ default n
+ depends on X86 && PCI
+ ---help---
+ This driver enables Power Management on AMD760MP & AMD760MPX chipsets. This is about same as ACPI C2, except that ACPI folks don't do SMP ATM.
+ See Documentation/amd76x_pm.txt for further details.
+
+ To compile this driver as a module ( = code which can be inserted in
+ and removed from the running kernel whenever you want), say M
+ here. The module will be called amd76x_pm.
+
+ If unsure, say N.
+
endmenu
diff -Nru linux-2.6.13/drivers/acpi/Makefile linux-2.6.13-jo/drivers/acpi/Makefile
--- linux-2.6.13/drivers/acpi/Makefile 2005-08-29 17:18:56.000000000 +0200
+++ linux-2.6.13-jo/drivers/acpi/Makefile 2005-08-29 21:03:50.000000000 +0200
@@ -57,3 +57,8 @@
obj-$(CONFIG_ACPI_TOSHIBA) += toshiba_acpi.o
obj-$(CONFIG_ACPI_BUS) += scan.o motherboard.o
obj-$(CONFIG_ACPI_HOTPLUG_MEMORY) += acpi_memhotplug.o
+
+#
+# not really ACPI thing, until they handle SMP.
+#
+obj-$(CONFIG_AMD76X_PM) += amd76x_pm.o
diff -Nru linux-2.6.13/drivers/acpi/amd76x_pm.c linux-2.6.13-jo/drivers/acpi/amd76x_pm.c
--- linux-2.6.13/drivers/acpi/amd76x_pm.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.13-jo/drivers/acpi/amd76x_pm.c 2005-09-01 21:50:34.000000000 +0200
@@ -0,0 +1,717 @@
+/*
+ * ACPI style PM for SMP AMD-760MP(X) based systems.
+ * For use until the ACPI project catches up. :-)
+ *
+ * Copyright (C) 2002 - 2005 Johnathan Hicks <[email protected]>
+ * Tony Lindgren <[email protected]>
+ * Joerg Sommrey <[email protected]>
+ *
+ * History:
+ *
+ * 20020702 - amd-smp-idle: Tony Lindgren <[email protected]>
+ * Influenced by Vcool, and LVCool. Rewrote everything from scratch to
+ * use the PCI features in Linux, and to support SMP systems. Provides
+ * C2 idling on SMP AMD-760MP systems.
+ *
+ * 20020722: JH
+ * I adapted Tony's code for the AMD-765/766 southbridge and adapted it
+ * according to the AMD-768 data sheet to provide the same capability for
+ * SMP AMD-760MPX systems. Posted to acpi-devel list.
+ *
+ * 20020722: Alan Cox
+ * Replaces non-functional amd76x_pm code in -ac tree.
+ *
+ * 20020730: JH
+ * Added ability to do normal throttling (the non-thermal kind), C3 idling
+ * and Power On Suspend (S1 sleep). It would be very easy to tie swsusp
+ * into activate_amd76x_SLP(). C3 idling doesn't happen yet; see my note
+ * in amd76x_smp_idle(). I've noticed that when NTH and idling are both
+ * enabled, my hardware locks and requires a hard reset, so I have
+ * #ifndefed around the idle loop setting to prevent this. POS locks it up
+ * too, both ought to be fixable. I've also noticed that idling and NTH
+ * make some interference that is picked up by the onboard sound chip on
+ * my ASUS A7M266-D motherboard.
+ *
+ * 20030601: Pasi Savolainen
+ * Simple port to 2.5
+ * Added sysfs interface for making nice graphs with mrtg.
+ * Look for /sys/devices/pci0/00:00.0/C2_cnt & lazy_idle (latter writable)
+ *
+ *
+ * 20050601: Joerg Sommrey (jo)
+ * 2.6 stuff
+ * redesigned amd76x_smp_idle. The algorithm is basically the same
+ * but the implementation has changed. This part is now independent
+ * from the number of CPUs and data is locked against concurrent
+ * updates from different CPUs.
+ * use _smp_processor_id()
+ * use cpu_idle_wait()
+ * NTH and POS code not touched and not tested.
+ *
+ * 20050621-extra: jo
+ * C3, NTH and POS code
+ *
+ * 20050812: jo
+ * rewritten amd76x_smp_idle completely. It's much simpler now but
+ * does a good job - the KISS approach. Introduced a new tunable
+ * spin_idle.
+ *
+ * 20050814: jo
+ * included POS, NTH and C3 in -extra patch
+ *
+ * 20050819: jo
+ * new irq rate watcher that forces C1-idling if irq-rate exceeds
+ * a given limit.
+ *
+ * 20050820: jo
+ * make all modules parameters r/w in sysfs.
+ *
+ * 20050821: jo
+ * removed an initialization bug.
+ *
+ * 20050830: jo
+ * some API changes for 2.6.13
+ *
+ * TODO: Thermal throttling (TTH).
+ * /proc interface for normal throttling level.
+ * /proc interface for POS.
+ *
+ *
+ * <Notes from 20020722-ac revision>
+ *
+ * Processor idle mode module for AMD SMP 760MP(X) based systems
+ *
+ * Copyright (C) 2002 Tony Lindgren <[email protected]>
+ * Johnathan Hicks (768 support)
+ *
+ * Using this module saves about 70 - 90W of energy in the idle mode compared
+ * to the default idle mode. Waking up from the idle mode is fast to keep the
+ * system response time good. Currently no CPU load calculation is done, the
+ * system exits the idle mode if the idle function runs twice on the same
+ * processor in a row. This only works on SMP systems, but maybe the idle mode
+ * enabling can be integrated to ACPI to provide C2 mode at some point.
+ *
+ * NOTE: Currently there's a bug somewhere where the reading the
+ * P_LVL2 for the first time causes the system to sleep instead of
+ * idling. This means that you need to hit the power button once to
+ * wake the system after loading the module for the first time after
+ * reboot. After that the system idles as supposed.
+ *
+ *
+ * Influenced by Vcool, and LVCool. Rewrote everything from scratch to
+ * use the PCI features in Linux, and to support SMP systems.
+ *
+ * Currently only tested on a TYAN S2460 (760MP) system (Tony) and an
+ * ASUS A7M266-D (760MPX) system (Johnathan). Adding support for other Athlon
+ * SMP or single processor systems should be easy if desired.
+ *
+ * This software is licensed under GNU General Public License Version 2
+ * as specified in file COPYING in the Linux kernel source tree main
+ * directory.
+ *
+ * </Notes from 20020722-ac revision>
+ */
+
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/fs.h>
+#include <linux/version.h>
+#include <asm/atomic.h>
+#include <linux/kernel.h>
+#include <linux/workqueue.h>
+#include <linux/jiffies.h>
+#include <linux/kernel_stat.h>
+
+#include <linux/amd76x_pm.h>
+
+#define VERSION "20050830"
+
+// #define AMD76X_LOG_C1 1
+
+extern void default_idle(void);
+static void amd76x_smp_idle(void);
+static int amd76x_pm_main(void);
+
+static unsigned long lazy_idle = 0;
+static unsigned long spin_idle = 0;
+static unsigned long watch_int = 0;
+static unsigned long min_C1 = AMD76X_MIN_C1;
+
+static int show_watch_irqs(char *, struct kernel_param *);
+static int set_watch_irqs(const char *, struct kernel_param *);
+
+module_param(lazy_idle, long, S_IRUGO | S_IWUSR);
+
+MODULE_PARM_DESC(lazy_idle,
+ "\tnumber of idle cycles before entering power saving mode");
+
+module_param(spin_idle, long, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(spin_idle,
+ "\tnumber of spin cycles to wait for other CPUs to become idle");
+
+module_param(watch_int, long, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(watch_int,
+ "\twatch interval (in milliseconds) for interrupts");
+
+module_param_call(watch_irqs, set_watch_irqs, show_watch_irqs,
+ NULL, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(watch_irqs,
+ "\tlist of irqs (and optional their limit per second) that "
+ "cause fallback to C1 mode. "
+ "Syntax: irq0[:limit0],irq1[:limit1],...");
+
+module_param(min_C1, long, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(min_C1,
+ "\tminimum irq rate watch intervals spent in C1 mode");
+
+MODULE_AUTHOR("Tony Lindgren, Johnathan Hicks, Joerg Sommrey, others");
+MODULE_DESCRIPTION("ACPI style power management for SMP AMD-760MP(X) "
+ "based systems, version " VERSION);
+
+
+static struct pci_dev *pdev_nb;
+static struct pci_dev *pdev_sb;
+
+struct PM_cfg {
+ unsigned int status_reg;
+ unsigned int C2_reg;
+ unsigned int slp_reg;
+ unsigned int resume_reg;
+ void (*orig_idle) (void);
+ void (*curr_idle) (void);
+};
+
+static struct PM_cfg amd76x_pm_cfg __cacheline_aligned_in_smp;
+
+struct idle_stat {
+ atomic_t num_idle;
+};
+
+static struct idle_stat amd76x_stat __cacheline_aligned_in_smp = {
+ .num_idle = ATOMIC_INIT(0),
+};
+
+struct cpu_stat {
+ int idle_count;
+ int C2_cnt;
+ int _fill[2];
+};
+
+static struct cpu_stat prs[NR_CPUS] __cacheline_aligned_in_smp;
+
+struct watch_item {
+ int irq;
+ int count;
+ int limit;
+ int _fill;
+};
+
+static struct irqwatch {
+ int force_C1;
+ int schedule;
+ int _fill[2];
+ struct watch_item item[AMD76X_WATCH_MAX];
+} irqwatch __cacheline_aligned_in_smp = {
+ .force_C1 = 0,
+ .schedule = 0,
+ .item = {{-1, 0}}
+};
+
+static struct work_struct work;
+static void watch_irq(void *);
+
+static DECLARE_WORK(work, watch_irq, NULL);
+
+static struct pci_device_id __devinitdata amd_nb_tbl[] = {
+ {PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, PCI_ANY_ID,
+ PCI_ANY_ID,},
+ {0,}
+};
+
+static struct pci_device_id __devinitdata amd_sb_tbl[] = {
+ {PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7413, PCI_ANY_ID,
+ PCI_ANY_ID,},
+ {PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7443, PCI_ANY_ID,
+ PCI_ANY_ID,},
+ {0,}
+};
+
+/*
+ * Configures the AMD-762 northbridge to support PM calls
+ */
+static int
+config_amd762(int enable)
+{
+ unsigned int regdword;
+
+ /* Enable STPGNT in BIU Status/Control for cpu0 */
+ pci_read_config_dword(pdev_nb, 0x60, ®dword);
+ regdword |= (1 << 17);
+ pci_write_config_dword(pdev_nb, 0x60, regdword);
+
+ /* Enable STPGNT in BIU Status/Control for cpu1 */
+ pci_read_config_dword(pdev_nb, 0x68, ®dword);
+ regdword |= (1 << 17);
+ pci_write_config_dword(pdev_nb, 0x68, regdword);
+
+ /* DRAM refresh enable */
+ pci_read_config_dword(pdev_nb, 0x58, ®dword);
+ regdword &= ~(1 << 19);
+ pci_write_config_dword(pdev_nb, 0x58, regdword);
+
+ /* Self refresh enable */
+ pci_read_config_dword(pdev_nb, 0x70, ®dword);
+ regdword |= (1 << 18);
+ pci_write_config_dword(pdev_nb, 0x70, regdword);
+
+ return 0;
+}
+
+
+/*
+ * Get the base PMIO address and set the pm registers in amd76x_pm_cfg.
+ */
+static void
+amd76x_get_PM(void)
+{
+ unsigned int regdword;
+
+ /* Get the address for pm status, P_LVL2, etc */
+ pci_read_config_dword(pdev_sb, 0x58, ®dword);
+ regdword &= 0xff80;
+ amd76x_pm_cfg.status_reg = (regdword + 0x00);
+ amd76x_pm_cfg.slp_reg = (regdword + 0x04);
+ amd76x_pm_cfg.C2_reg = (regdword + 0x14);
+ amd76x_pm_cfg.resume_reg = (regdword + 0x16); /* N/A for 768 */
+}
+
+
+/*
+ * En/Disable PMIO and configure W4SG & STPGNT.
+ */
+static int
+config_PMIO_amd76x(int is_766, int enable)
+{
+ unsigned char regbyte;
+
+ /* Clear W4SG, and set PMIOEN, if using a 765/766 set STPGNT as well.
+ * AMD-766: C3A41; page 59 in AMD-766 doc
+ * AMD-768: DevB:3x41C; page 94 in AMD-768 doc */
+ pci_read_config_byte(pdev_sb, 0x41, ®byte);
+ if(enable) {
+ regbyte |= ((is_766 << 1) | (1 << 7));
+ }
+ pci_write_config_byte(pdev_sb, 0x41, regbyte);
+ return 0;
+}
+
+/*
+ * C2 idle support for AMD-766.
+ */
+static void
+config_amd766_C2(int enable)
+{
+ unsigned int regdword;
+
+ /* Set C2 options in C3A50, page 63 in AMD-766 doc */
+ pci_read_config_dword(pdev_sb, 0x50, ®dword);
+ if(enable) {
+ regdword &= ~((DCSTOP_EN | CPUSTP_EN | PCISTP_EN | SUSPND_EN |
+ CPURST_EN) << C2_REGS);
+ regdword |= (STPCLK_EN /* ~ 20 Watt savings max */
+ | CPUSLP_EN) /* Additional ~ 70 Watts max! */
+ << C2_REGS;
+ }
+ else
+ regdword &= ~((STPCLK_EN | CPUSLP_EN) << C2_REGS);
+ pci_write_config_dword(pdev_sb, 0x50, regdword);
+}
+
+/*
+ * Configures the 765 & 766 southbridges.
+ */
+static int
+config_amd766(int enable)
+{
+ amd76x_get_PM();
+ config_PMIO_amd76x(1, 1);
+ config_amd766_C2(enable);
+
+ return 0;
+}
+
+
+/*
+ * C2 idling support for AMD-768.
+ */
+static void
+config_amd768_C2(int enable)
+{
+ unsigned char regbyte;
+
+ /* Set C2 options in DevB:3x4F, page 100 in AMD-768 doc */
+ pci_read_config_byte(pdev_sb, 0x4F, ®byte);
+ if(enable)
+ regbyte |= C2EN;
+ else
+ regbyte ^= C2EN;
+ pci_write_config_byte(pdev_sb, 0x4F, regbyte);
+}
+
+/*
+ * Configures the 768 southbridge to support idle calls, and gets
+ * the processor idle call register location.
+ */
+static int
+config_amd768(int enable)
+{
+ amd76x_get_PM();
+
+ config_PMIO_amd76x(0, 1);
+
+ config_amd768_C2(enable);
+
+ return 0;
+}
+
+/*
+ * Idle loop for single processor systems
+ */
+void
+amd76x_up_idle(void)
+{
+ /* ACPI knows how to do C2 on SMP when cpu_count < 2
+ * we really shouldn't end up here anyway.
+ */
+ amd76x_pm_cfg.orig_idle();
+}
+
+/*
+ * Idle loop for SMP systems
+ *
+ * Locking is done using atomic_t variables, no spin locks needed.
+ *
+ */
+static void
+amd76x_smp_idle(void)
+{
+ int cpu;
+ int i;
+ int num_online;
+
+ local_irq_disable();
+ cpu = smp_processor_id();
+ if (unlikely(irqwatch.force_C1)) {
+ prs[cpu].idle_count = 0;
+ safe_halt();
+ return;
+ }
+
+ /* Spin inside (outer) idle loop until lazy_idle cycles
+ * are reached.
+ */
+ if (likely(++prs[cpu].idle_count <= lazy_idle)) {
+ local_irq_enable();
+ return;
+ }
+
+ /* Now we are ready do go C2. */
+ atomic_inc(&amd76x_stat.num_idle);
+ num_online = num_online_cpus();
+
+ /* Spin inside inner loop until either
+ * - spin_idle cycles are reached
+ * - there is work
+ * - all CPUs are idle
+ */
+ for (i = 0; i < spin_idle; i++) {
+ if (unlikely(need_resched()))
+ break;
+
+ smp_mb();
+ if (unlikely(atomic_read(&amd76x_stat.num_idle) ==
+ num_online)) {
+ /* Invoke C2 */
+ prs[cpu].C2_cnt++;
+ inb(amd76x_pm_cfg.C2_reg);
+ smp_mb();
+ atomic_dec(&amd76x_stat.num_idle);
+ prs[cpu].idle_count = 0;
+ local_irq_enable();
+ return;
+ }
+ }
+
+ smp_mb();
+ atomic_dec(&amd76x_stat.num_idle);
+ prs[cpu].idle_count = 0;
+ local_irq_enable();
+}
+
+/*
+ * sysfs support, RW
+ */
+static int
+show_watch_irqs(char *buf, struct kernel_param *kp)
+{
+ int i;
+ ssize_t ret = 0;
+ for (i = 0; i < AMD76X_WATCH_MAX && irqwatch.item[i].irq != -1 ; i++) {
+ if (i > 0)
+ ret += sprintf(buf + ret, ",");
+ ret += sprintf(buf + ret, "%d:%d",
+ irqwatch.item[i].irq,
+ irqwatch.item[i].limit);
+ }
+ return ret;
+}
+
+static int
+set_watch_irqs(const char *val, struct kernel_param *kp)
+{
+ const char *s;
+ char *e;
+ long irq, limit;
+ int i;
+
+ for (i = 0, s = val; i < AMD76X_WATCH_MAX && s && *s; i++) {
+ irq = simple_strtol(s, &e, 0);
+ if (e == s)
+ break;
+ if (*e == ':') {
+ s = e + 1;
+ limit = simple_strtol(s, &e, 0);
+ } else
+ limit = AMD76X_WATCH_LIM;
+ if (irq >= 0)
+ irqwatch.item[i].irq = irq;
+ else {
+ irqwatch.item[i].irq = -1;
+ break;
+ }
+ irqwatch.item[i].limit = limit;
+ irqwatch.item[i].count = 0;
+ if (*e == ',')
+ s = e + 1;
+ else
+ s = e;
+ }
+ if (i < AMD76X_WATCH_MAX)
+ irqwatch.item[i].irq = -1;
+ if (irqwatch.item[0].irq != -1) {
+ irqwatch.schedule = 1;
+ printk(KERN_INFO "amd76x_pm: irq rate watcher parms:\n");
+ for (i = 0; i < AMD76X_WATCH_MAX && irqwatch.item[i].irq != -1; i++)
+ printk(KERN_INFO
+ "amd76x_pm: irq %d: limit = %d/s\n",
+ irqwatch.item[i].irq,
+ irqwatch.item[i].limit);
+ } else
+ printk(KERN_INFO "amd76x_pm: irq rate watcher disabled.\n");
+
+ return 0;
+}
+
+static ssize_t
+show_C2_cnt (struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ unsigned int C2_cnt = 0;
+ int i;
+
+ for_each_online_cpu(i)
+ C2_cnt += prs[i].C2_cnt;
+ return sprintf(buf,"%u\n", C2_cnt);
+}
+
+static DEVICE_ATTR(C2_cnt, S_IRUGO,
+ show_C2_cnt, NULL);
+
+static void
+setup_watch(void)
+{
+ if (watch_int <= 0)
+ watch_int = AMD76X_WATCH_INT;
+ if (irqwatch.item[0].irq != -1 && watch_int) {
+ schedule_work(&work);
+ printk(KERN_INFO "amd76x_pm: irq rate watcher started. "
+ "watch_int = %lu ms, min_C1 = %lu\n",
+ watch_int, min_C1);
+ } else
+ printk(KERN_INFO "amd76x_pm: irq rate watcher disabled.\n");
+}
+
+static void
+watch_irq(void *parm)
+{
+ int i;
+ int irq_cnt;
+ int force_C1 = 0;
+
+ for (i = 0; i < AMD76X_WATCH_MAX && irqwatch.item[i].irq != -1; i++) {
+ irq_cnt = kstat_irqs(irqwatch.item[i].irq);
+ if ((irq_cnt - irqwatch.item[i].count) * 1000 >
+ irqwatch.item[i].limit * watch_int) {
+ force_C1 = 1;
+ }
+ irqwatch.item[i].count = irq_cnt;
+ }
+
+#ifdef AMD76X_LOG_C1
+ if (force_C1 && !irqwatch.force_C1)
+ printk(KERN_INFO "amd76x_pm: C1 on\n");
+ if (!force_C1 && irqwatch.force_C1 == 1)
+ printk(KERN_INFO "amd76x_pm: C1 off\n");
+#endif
+
+ if (force_C1)
+ irqwatch.force_C1 = min_C1;
+ else if (irqwatch.force_C1)
+ irqwatch.force_C1--;
+
+ if (irqwatch.schedule && watch_int > 0)
+ schedule_delayed_work(&work,
+ msecs_to_jiffies(watch_int));
+ else
+ printk(KERN_INFO "amd76x_pm: irq rate watcher stopped.\n");
+}
+
+
+/*
+ * Finds and initializes the bridges, and then sets the idle function
+ */
+static int
+amd76x_pm_main(void)
+{
+ int i;
+
+ amd76x_pm_cfg.orig_idle = 0;
+ if(lazy_idle == 0)
+ lazy_idle = AMD76X_LAZY_IDLE;
+ printk(KERN_INFO "amd76x_pm: lazy_idle = %lu\n", lazy_idle);
+ if(spin_idle == 0)
+ spin_idle = 2 * lazy_idle;
+ printk(KERN_INFO "amd76x_pm: spin_idle = %lu\n", spin_idle);
+
+ /* Find southbridge */
+ pdev_sb = NULL;
+ while((pdev_sb = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, pdev_sb)) != NULL) {
+ if(pci_match_id(amd_sb_tbl, pdev_sb) != NULL)
+ goto found_sb;
+ }
+ printk(KERN_ERR "amd76x_pm: Could not find southbridge\n");
+ return -ENODEV;
+
+ found_sb:
+
+ /* Find northbridge */
+ pdev_nb = NULL;
+ while((pdev_nb = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, pdev_nb)) != NULL) {
+ if(pci_match_id(amd_nb_tbl, pdev_nb) != NULL)
+ goto found_nb;
+ }
+ printk(KERN_ERR "amd76x_pm: Could not find northbridge\n");
+ return -ENODEV;
+
+ found_nb:
+
+ /* Init southbridge */
+ switch (pdev_sb->device) {
+ case PCI_DEVICE_ID_AMD_VIPER_7413: /* AMD-765 or 766 */
+ config_amd766(1);
+ break;
+ case PCI_DEVICE_ID_AMD_VIPER_7443: /* AMD-768 */
+ config_amd768(1);
+ break;
+ default:
+ printk(KERN_ERR "amd76x_pm: No southbridge to initialize\n");
+ break;
+ }
+
+ /* Init northbridge and queue the new idle function */
+ if(!pdev_nb) {
+ printk("amd76x_pm: No northbridge found.\n");
+ return -ENODEV;
+ }
+ switch (pdev_nb->device) {
+ case PCI_DEVICE_ID_AMD_FE_GATE_700C: /* AMD-762 */
+ config_amd762(1);
+ amd76x_pm_cfg.curr_idle = amd76x_smp_idle;
+ break;
+ default:
+ printk(KERN_ERR "amd76x_pm: No northbridge to initialize\n");
+ break;
+ }
+
+ if(num_online_cpus() == 1) {
+ amd76x_pm_cfg.curr_idle = amd76x_up_idle;
+ printk(KERN_ERR "amd76x_pm: UP machine detected. ACPI is your friend.\n");
+ }
+ if (!amd76x_pm_cfg.curr_idle) {
+ printk(KERN_ERR "amd76x_pm: Idle function not changed\n");
+ return 1;
+ }
+
+ for (i = 0; i < NR_CPUS; i++) {
+ prs[i].idle_count = 0;
+ prs[i].C2_cnt = 0;
+ }
+
+ amd76x_pm_cfg.orig_idle = pm_idle;
+ pm_idle = amd76x_pm_cfg.curr_idle;
+
+ wmb();
+
+ /* sysfs */
+ device_create_file(&pdev_nb->dev, &dev_attr_C2_cnt);
+
+ setup_watch();
+
+ return 0;
+}
+
+
+static int __init
+amd76x_pm_init(void)
+{
+ printk(KERN_INFO "amd76x_pm: Version %s loaded.\n", VERSION);
+ return amd76x_pm_main();
+}
+
+
+static void __exit
+amd76x_pm_cleanup(void)
+{
+ int i;
+ unsigned int C2_cnt = 0;
+
+ pm_idle = amd76x_pm_cfg.orig_idle;
+
+ cpu_idle_wait();
+
+
+ /* This isn't really needed. */
+ for_each_online_cpu(i) {
+ C2_cnt += prs[i].C2_cnt;
+ }
+ printk(KERN_INFO "amd76x_pm: %u C2 calls\n", C2_cnt);
+
+ /* remove sysfs */
+ device_remove_file(&pdev_nb->dev, &dev_attr_C2_cnt);
+
+ irqwatch.schedule = 0;
+ flush_scheduled_work();
+ cancel_delayed_work(&work);
+ flush_scheduled_work();
+}
+
+
+MODULE_LICENSE("GPL");
+module_init(amd76x_pm_init);
+module_exit(amd76x_pm_cleanup);
diff -Nru linux-2.6.13/include/linux/amd76x_pm.h linux-2.6.13-jo/include/linux/amd76x_pm.h
--- linux-2.6.13/include/linux/amd76x_pm.h 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.13-jo/include/linux/amd76x_pm.h 2005-08-29 21:03:50.000000000 +0200
@@ -0,0 +1,63 @@
+/*
+ * Begin 765/766
+ */
+/* C2/C3/POS options in C3A50, page 63 in AMD-766 doc */
+#define ZZ_CACHE_EN 1
+#define DCSTOP_EN (1 << 1)
+#define STPCLK_EN (1 << 2)
+#define CPUSTP_EN (1 << 3)
+#define PCISTP_EN (1 << 4)
+#define CPUSLP_EN (1 << 5)
+#define SUSPND_EN (1 << 6)
+#define CPURST_EN (1 << 7)
+
+#define C2_REGS 0
+#define C3_REGS 8
+#define POS_REGS 16
+/*
+ * End 765/766
+ */
+
+
+/*
+ * Begin 768
+ */
+/* C2/C3 options in DevB:3x4F, page 100 in AMD-768 doc */
+#define C2EN 1
+#define C3EN (1 << 1)
+#define ZZ_C3EN (1 << 2)
+#define CSLP_C3EN (1 << 3)
+#define CSTP_C3EN (1 << 4)
+
+/* POS options in DevB:3x50, page 101 in AMD-768 doc */
+#define POSEN 1
+#define CSTP (1 << 2)
+#define PSTP (1 << 3)
+#define ASTP (1 << 4)
+#define DCSTP (1 << 5)
+#define CSLP (1 << 6)
+#define SUSP (1 << 8)
+#define MSRSM (1 << 14)
+#define PITRSM (1 << 15)
+
+/* NTH options DevB:3x40, pg 93 of 768 doc */
+#define NTPER(x) (x << 3)
+#define THMINEN(x) (x << 4)
+
+/*
+ * End 768
+ */
+
+/* NTH activate. PM10, pg 110 of 768 doc, pg 70 of 766 doc */
+#define NTH_RATIO(x) (x << 1)
+#define NTH_EN (1 << 4)
+
+/* Sleep state. PM04, pg 109 of 768 doc, pg 69 of 766 doc */
+#define SLP_EN (1 << 13)
+#define SLP_TYP(x) (x << 10)
+
+#define AMD76X_LAZY_IDLE 512
+#define AMD76X_WATCH_INT 500
+#define AMD76X_WATCH_LIM 128
+#define AMD76X_WATCH_MAX 8
+#define AMD76X_MIN_C1 2
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
| |
 |