> Looks pretty good to me. Small issues I've identified: > > - what do you need the hba_count attribute for? This should be > implementable in userspace pretty easily by iterating of all > devices of the scsi_host class that are attached to the driver I have removed hba_count > - the ->queuecommand cleanup patch I sent you a awhile ago doesn't > seem to be applied I seem to have missed it. I will submit the patch after inclusion > - there's quite a lot of slightly odd formating, it would be nice > if you could run the code through scripts/Lindent. I ran Lindent. It looks worse :( I am submitting the Lindent output anyway. > > If you could sent out an unmangled patch (even as attachment or on > LSI's ftp side) I'd like to take another, closer look. I am sending this from a Linux box. Hopefully, this will comeout clean. Sorry for mangled patches. Signed-off-by: Sreenivas Bagalkote <[email protected]> diff -Naur scsi_misc-a/drivers/scsi/Makefile scsi_misc-b/drivers/scsi/Makefile --- scsi_misc-a/drivers/scsi/Makefile 2005-08-25 16:25:07.000000000 -0400 +++ scsi_misc-b/drivers/scsi/Makefile 2005-08-25 16:28:08.000000000 -0400 @@ -96,6 +96,7 @@ obj-$(CONFIG_SCSI_DC390T) += tmscsim.o obj-$(CONFIG_MEGARAID_LEGACY) += megaraid.o obj-$(CONFIG_MEGARAID_NEWGEN) += megaraid/ +obj-$(CONFIG_MEGARAID_SAS) += megaraid/ obj-$(CONFIG_SCSI_ACARD) += atp870u.o obj-$(CONFIG_SCSI_SUNESP) += esp.o obj-$(CONFIG_SCSI_GDTH) += gdth.o diff -Naur scsi_misc-a/drivers/scsi/megaraid/Kconfig.megaraid scsi_misc-b/drivers/scsi/megaraid/Kconfig.megaraid --- scsi_misc-a/drivers/scsi/megaraid/Kconfig.megaraid 2005-08-25 16:25:06.000000000 -0400 +++ scsi_misc-b/drivers/scsi/megaraid/Kconfig.megaraid 2005-08-25 16:27:29.000000000 -0400 @@ -76,3 +76,12 @@ To compile this driver as a module, choose M here: the module will be called megaraid endif + +config MEGARAID_SAS + tristate "LSI Logic MegaRAID SAS RAID Module" + depends on PCI && SCSI + help + Module for LSI Logic's SAS based RAID controllers. + To compile this driver as a module, choose 'm' here. + Module will be called megaraid_sas + diff -Naur scsi_misc-a/drivers/scsi/megaraid/Makefile scsi_misc-b/drivers/scsi/megaraid/Makefile --- scsi_misc-a/drivers/scsi/megaraid/Makefile 2005-08-25 16:25:06.000000000 -0400 +++ scsi_misc-b/drivers/scsi/megaraid/Makefile 2005-08-25 16:27:23.000000000 -0400 @@ -1,2 +1,3 @@ obj-$(CONFIG_MEGARAID_MM) += megaraid_mm.o obj-$(CONFIG_MEGARAID_MAILBOX) += megaraid_mbox.o +obj-$(CONFIG_MEGARAID_SAS) += megaraid_sas.o diff -Naur scsi_misc-a/drivers/scsi/megaraid/megaraid_sas.h scsi_misc-b/drivers/scsi/megaraid/megaraid_sas.h --- scsi_misc-a/drivers/scsi/megaraid/megaraid_sas.h 1969-12-31 19:00:00.000000000 -0500 +++ scsi_misc-b/drivers/scsi/megaraid/megaraid_sas.h 2005-08-31 13:24:29.291554792 -0400 @@ -0,0 +1,1123 @@ +/* + * + * Linux MegaRAID driver for SAS based RAID controllers + * + * Copyright (c) 2003-2005 LSI Logic Corporation. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * FILE : megaraid_sas.h + */ + +#ifndef LSI_MEGARAID_SAS_H +#define LSI_MEGARAID_SAS_H + +/** + * MegaRAID SAS Driver meta data + */ +#define MEGASAS_VERSION "00.00.02.00-rc1" +#define MEGASAS_RELDATE "Aug 28, 2005" +#define MEGASAS_EXT_VERSION "Sun Aug 28 21:30:34 EDT 2005" + +/* + * ===================================== + * MegaRAID SAS MFI firmware definitions + * ===================================== + */ + +/* + * MFI stands for MegaRAID SAS FW Interface. This is just a moniker +for + * protocol between the software and firmware. Commands are issued +using + * "message frames" + */ + +/** + * FW posts its state in upper 4 bits of outbound_msg_0 register */ +#define MFI_STATE_MASK 0xF0000000 +#define MFI_STATE_UNDEFINED 0x00000000 +#define MFI_STATE_BB_INIT 0x10000000 +#define MFI_STATE_FW_INIT 0x40000000 +#define MFI_STATE_WAIT_HANDSHAKE 0x60000000 +#define MFI_STATE_FW_INIT_2 0x70000000 +#define MFI_STATE_DEVICE_SCAN 0x80000000 +#define MFI_STATE_FLUSH_CACHE 0xA0000000 +#define MFI_STATE_READY 0xB0000000 +#define MFI_STATE_OPERATIONAL 0xC0000000 +#define MFI_STATE_FAULT 0xF0000000 + +#define MEGAMFI_FRAME_SIZE 64 + +/** + * During FW init, clear pending cmds & reset state using inbound_msg_0 + * + * ABORT : Abort all pending cmds + * READY : Move from OPERATIONAL to READY state; discard queue info + * MFIMODE : Discard (possible) low MFA posted in 64-bit mode (??) + * CLR_HANDSHAKE: FW is waiting for HANDSHAKE from BIOS or Driver */ +#define MFI_INIT_ABORT 0x00000000 +#define MFI_INIT_READY 0x00000002 +#define MFI_INIT_MFIMODE 0x00000004 +#define MFI_INIT_CLEAR_HANDSHAKE 0x00000008 +#define MFI_RESET_FLAGS MFI_INIT_READY|MFI_INIT_MFIMODE + +/** + * MFI frame flags + */ +#define MFI_FRAME_POST_IN_REPLY_QUEUE 0x0000 +#define MFI_FRAME_DONT_POST_IN_REPLY_QUEUE 0x0001 +#define MFI_FRAME_SGL32 0x0000 +#define MFI_FRAME_SGL64 0x0002 +#define MFI_FRAME_SENSE32 0x0000 +#define MFI_FRAME_SENSE64 0x0004 +#define MFI_FRAME_DIR_NONE 0x0000 +#define MFI_FRAME_DIR_WRITE 0x0008 +#define MFI_FRAME_DIR_READ 0x0010 +#define MFI_FRAME_DIR_BOTH 0x0018 + +/** + * Definition for cmd_status + */ +#define MFI_CMD_STATUS_POLL_MODE 0xFF + +/** + * MFI command opcodes + */ +#define MFI_CMD_INIT 0x00 +#define MFI_CMD_LD_READ 0x01 +#define MFI_CMD_LD_WRITE 0x02 +#define MFI_CMD_LD_SCSI_IO 0x03 +#define MFI_CMD_PD_SCSI_IO 0x04 +#define MFI_CMD_DCMD 0x05 +#define MFI_CMD_ABORT 0x06 +#define MFI_CMD_SMP 0x07 +#define MFI_CMD_STP 0x08 + +#define MR_DCMD_CTRL_GET_INFO 0x01010000 + +#define MR_DCMD_CTRL_CACHE_FLUSH 0x01101000 +#define MR_FLUSH_CTRL_CACHE 0x01 +#define MR_FLUSH_DISK_CACHE 0x02 + +#define MR_DCMD_CTRL_SHUTDOWN 0x01050000 +#define MR_ENABLE_DRIVE_SPINDOWN 0x01 + +#define MR_DCMD_CTRL_EVENT_GET_INFO 0x01040100 +#define MR_DCMD_CTRL_EVENT_GET 0x01040300 +#define MR_DCMD_CTRL_EVENT_WAIT 0x01040500 +#define MR_DCMD_LD_GET_PROPERTIES 0x03030000 + +#define MR_DCMD_CLUSTER 0x08000000 +#define MR_DCMD_CLUSTER_RESET_ALL 0x08010100 +#define MR_DCMD_CLUSTER_RESET_LD 0x08010200 + +/** + * MFI command completion codes + */ +enum MFI_STAT { + MFI_STAT_OK = 0x00, + MFI_STAT_INVALID_CMD = 0x01, + MFI_STAT_INVALID_DCMD = 0x02, + MFI_STAT_INVALID_PARAMETER = 0x03, + MFI_STAT_INVALID_SEQUENCE_NUMBER = 0x04, + MFI_STAT_ABORT_NOT_POSSIBLE = 0x05, + MFI_STAT_APP_HOST_CODE_NOT_FOUND = 0x06, + MFI_STAT_APP_IN_USE = 0x07, + MFI_STAT_APP_NOT_INITIALIZED = 0x08, + MFI_STAT_ARRAY_INDEX_INVALID = 0x09, + MFI_STAT_ARRAY_ROW_NOT_EMPTY = 0x0a, + MFI_STAT_CONFIG_RESOURCE_CONFLICT = 0x0b, + MFI_STAT_DEVICE_NOT_FOUND = 0x0c, + MFI_STAT_DRIVE_TOO_SMALL = 0x0d, + MFI_STAT_FLASH_ALLOC_FAIL = 0x0e, + MFI_STAT_FLASH_BUSY = 0x0f, + MFI_STAT_FLASH_ERROR = 0x10, + MFI_STAT_FLASH_IMAGE_BAD = 0x11, + MFI_STAT_FLASH_IMAGE_INCOMPLETE = 0x12, + MFI_STAT_FLASH_NOT_OPEN = 0x13, + MFI_STAT_FLASH_NOT_STARTED = 0x14, + MFI_STAT_FLUSH_FAILED = 0x15, + MFI_STAT_HOST_CODE_NOT_FOUNT = 0x16, + MFI_STAT_LD_CC_IN_PROGRESS = 0x17, + MFI_STAT_LD_INIT_IN_PROGRESS = 0x18, + MFI_STAT_LD_LBA_OUT_OF_RANGE = 0x19, + MFI_STAT_LD_MAX_CONFIGURED = 0x1a, + MFI_STAT_LD_NOT_OPTIMAL = 0x1b, + MFI_STAT_LD_RBLD_IN_PROGRESS = 0x1c, + MFI_STAT_LD_RECON_IN_PROGRESS = 0x1d, + MFI_STAT_LD_WRONG_RAID_LEVEL = 0x1e, + MFI_STAT_MAX_SPARES_EXCEEDED = 0x1f, + MFI_STAT_MEMORY_NOT_AVAILABLE = 0x20, + MFI_STAT_MFC_HW_ERROR = 0x21, + MFI_STAT_NO_HW_PRESENT = 0x22, + MFI_STAT_NOT_FOUND = 0x23, + MFI_STAT_NOT_IN_ENCL = 0x24, + MFI_STAT_PD_CLEAR_IN_PROGRESS = 0x25, + MFI_STAT_PD_TYPE_WRONG = 0x26, + MFI_STAT_PR_DISABLED = 0x27, + MFI_STAT_ROW_INDEX_INVALID = 0x28, + MFI_STAT_SAS_CONFIG_INVALID_ACTION = 0x29, + MFI_STAT_SAS_CONFIG_INVALID_DATA = 0x2a, + MFI_STAT_SAS_CONFIG_INVALID_PAGE = 0x2b, + MFI_STAT_SAS_CONFIG_INVALID_TYPE = 0x2c, + MFI_STAT_SCSI_DONE_WITH_ERROR = 0x2d, + MFI_STAT_SCSI_IO_FAILED = 0x2e, + MFI_STAT_SCSI_RESERVATION_CONFLICT = 0x2f, + MFI_STAT_SHUTDOWN_FAILED = 0x30, + MFI_STAT_TIME_NOT_SET = 0x31, + MFI_STAT_WRONG_STATE = 0x32, + MFI_STAT_LD_OFFLINE = 0x33, + MFI_STAT_PEER_NOTIFICATION_REJECTED = 0x34, + MFI_STAT_PEER_NOTIFICATION_FAILED = 0x35, + MFI_STAT_RESERVATION_IN_PROGRESS = 0x36, + MFI_STAT_I2C_ERRORS_DETECTED = 0x37, + MFI_STAT_PCI_ERRORS_DETECTED = 0x38, + + MFI_STAT_INVALID_STATUS = 0xFF +}; + +/* + * Number of mailbox bytes in DCMD message frame */ +#define MFI_MBOX_SIZE 12 + +enum MR_EVT_CLASS { + + MR_EVT_CLASS_DEBUG = -2, + MR_EVT_CLASS_PROGRESS = -1, + MR_EVT_CLASS_INFO = 0, + MR_EVT_CLASS_WARNING = 1, + MR_EVT_CLASS_CRITICAL = 2, + MR_EVT_CLASS_FATAL = 3, + MR_EVT_CLASS_DEAD = 4, + +}; + +enum MR_EVT_LOCALE { + + MR_EVT_LOCALE_LD = 0x0001, + MR_EVT_LOCALE_PD = 0x0002, + MR_EVT_LOCALE_ENCL = 0x0004, + MR_EVT_LOCALE_BBU = 0x0008, + MR_EVT_LOCALE_SAS = 0x0010, + MR_EVT_LOCALE_CTRL = 0x0020, + MR_EVT_LOCALE_CONFIG = 0x0040, + MR_EVT_LOCALE_CLUSTER = 0x0080, + MR_EVT_LOCALE_ALL = 0xffff, + +}; + +enum MR_EVT_ARGS { + + MR_EVT_ARGS_NONE, + MR_EVT_ARGS_CDB_SENSE, + MR_EVT_ARGS_LD, + MR_EVT_ARGS_LD_COUNT, + MR_EVT_ARGS_LD_LBA, + MR_EVT_ARGS_LD_OWNER, + MR_EVT_ARGS_LD_LBA_PD_LBA, + MR_EVT_ARGS_LD_PROG, + MR_EVT_ARGS_LD_STATE, + MR_EVT_ARGS_LD_STRIP, + MR_EVT_ARGS_PD, + MR_EVT_ARGS_PD_ERR, + MR_EVT_ARGS_PD_LBA, + MR_EVT_ARGS_PD_LBA_LD, + MR_EVT_ARGS_PD_PROG, + MR_EVT_ARGS_PD_STATE, + MR_EVT_ARGS_PCI, + MR_EVT_ARGS_RATE, + MR_EVT_ARGS_STR, + MR_EVT_ARGS_TIME, + MR_EVT_ARGS_ECC, + +}; + +/* + * SAS controller properties + */ +struct megasas_ctrl_prop { + + u16 seq_num; + u16 pred_fail_poll_interval; + u16 intr_throttle_count; + u16 intr_throttle_timeouts; + u8 rebuild_rate; + u8 patrol_read_rate; + u8 bgi_rate; + u8 cc_rate; + u8 recon_rate; + u8 cache_flush_interval; + u8 spinup_drv_count; + u8 spinup_delay; + u8 cluster_enable; + u8 coercion_mode; + u8 alarm_enable; + u8 disable_auto_rebuild; + u8 disable_battery_warn; + u8 ecc_bucket_size; + u16 ecc_bucket_leak_rate; + u8 restore_hotspare_on_insertion; + u8 expose_encl_devices; + u8 reserved[38]; + +} __attribute__ ((packed)); + +/* + * SAS controller information + */ +struct megasas_ctrl_info { + + /* + * PCI device information + */ + struct { + + u16 vendor_id; + u16 device_id; + u16 sub_vendor_id; + u16 sub_device_id; + u8 reserved[24]; + + } __attribute__ ((packed)) pci; + + /* + * Host interface information + */ + struct { + + u8 PCIX:1; + u8 PCIE:1; + u8 iSCSI:1; + u8 SAS_3G:1; + u8 reserved_0:4; + u8 reserved_1[6]; + u8 port_count; + u64 port_addr[8]; + + } __attribute__ ((packed)) host_interface; + + /* + * Device (backend) interface information + */ + struct { + + u8 SPI:1; + u8 SAS_3G:1; + u8 SATA_1_5G:1; + u8 SATA_3G:1; + u8 reserved_0:4; + u8 reserved_1[6]; + u8 port_count; + u64 port_addr[8]; + + } __attribute__ ((packed)) device_interface; + + /* + * List of components residing in flash. All str are null terminated + */ + u32 image_check_word; + u32 image_component_count; + + struct { + + char name[8]; + char version[32]; + char build_date[16]; + char built_time[16]; + + } __attribute__ ((packed)) image_component[8]; + + /* + * List of flash components that have been flashed on the card, but + * are not in use, pending reset of the adapter. This list will be + * empty if a flash operation has not occurred. All stings are null + * terminated + */ + u32 pending_image_component_count; + + struct { + + char name[8]; + char version[32]; + char build_date[16]; + char build_time[16]; + + } __attribute__ ((packed)) pending_image_component[8]; + + u8 max_arms; + u8 max_spans; + u8 max_arrays; + u8 max_lds; + + char product_name[80]; + char serial_no[32]; + + /* + * Other physical/controller/operation information. Indicates the + * presence of the hardware + */ + struct { + + u32 bbu:1; + u32 alarm:1; + u32 nvram:1; + u32 uart:1; + u32 reserved:28; + + } __attribute__ ((packed)) hw_present; + + u32 current_fw_time; + + /* + * Maximum data transfer sizes + */ + u16 max_concurrent_cmds; + u16 max_sge_count; + u32 max_request_size; + + /* + * Logical and physical device counts + */ + u16 ld_present_count; + u16 ld_degraded_count; + u16 ld_offline_count; + + u16 pd_present_count; + u16 pd_disk_present_count; + u16 pd_disk_pred_failure_count; + u16 pd_disk_failed_count; + + /* + * Memory size information + */ + u16 nvram_size; + u16 memory_size; + u16 flash_size; + + /* + * Error counters + */ + u16 mem_correctable_error_count; + u16 mem_uncorrectable_error_count; + + /* + * Cluster information + */ + u8 cluster_permitted; + u8 cluster_active; + + /* + * Additional max data transfer sizes + */ + u16 max_strips_per_io; + + /* + * Controller capabilities structures + */ + struct { + + u32 raid_level_0:1; + u32 raid_level_1:1; + u32 raid_level_5:1; + u32 raid_level_1E:1; + u32 raid_level_6:1; + u32 reserved:27; + + } __attribute__ ((packed)) raid_levels; + + struct { + + u32 rbld_rate:1; + u32 cc_rate:1; + u32 bgi_rate:1; + u32 recon_rate:1; + u32 patrol_rate:1; + u32 alarm_control:1; + u32 cluster_supported:1; + u32 bbu:1; + u32 spanning_allowed:1; + u32 dedicated_hotspares:1; + u32 revertible_hotspares:1; + u32 foreign_config_import:1; + u32 self_diagnostic:1; + u32 mixed_redundancy_arr:1; + u32 global_hot_spares:1; + u32 reserved:17; + + } __attribute__ ((packed)) adapter_operations; + + struct { + + u32 read_policy:1; + u32 write_policy:1; + u32 io_policy:1; + u32 access_policy:1; + u32 disk_cache_policy:1; + u32 reserved:27; + + } __attribute__ ((packed)) ld_operations; + + struct { + + u8 min; + u8 max; + u8 reserved[2]; + + } __attribute__ ((packed)) stripe_sz_ops; + + struct { + + u32 force_online:1; + u32 force_offline:1; + u32 force_rebuild:1; + u32 reserved:29; + + } __attribute__ ((packed)) pd_operations; + + struct { + + u32 ctrl_supports_sas:1; + u32 ctrl_supports_sata:1; + u32 allow_mix_in_encl:1; + u32 allow_mix_in_ld:1; + u32 allow_sata_in_cluster:1; + u32 reserved:27; + + } __attribute__ ((packed)) pd_mix_support; + + /* + * Define ECC single-bit-error bucket information + */ + u8 ecc_bucket_count; + u8 reserved_2[11]; + + /* + * Include the controller properties (changeable items) + */ + struct megasas_ctrl_prop properties; + + /* + * Define FW pkg version (set in envt v'bles on OEM basis) + */ + char package_version[0x60]; + + u8 pad[0x800 - 0x6a0]; + +} __attribute__ ((packed)); + +/* + * =============================== + * MegaRAID SAS driver definitions + * =============================== + */ +#define MEGASAS_MAX_PD_CHANNELS 2 +#define MEGASAS_MAX_LD_CHANNELS 2 +#define MEGASAS_MAX_CHANNELS (MEGASAS_MAX_PD_CHANNELS + \ + MEGASAS_MAX_LD_CHANNELS) +#define MEGASAS_MAX_DEV_PER_CHANNEL 128 +#define MEGASAS_DEFAULT_INIT_ID -1 +#define MEGASAS_MAX_LUN 8 +#define MEGASAS_MAX_LD 64 + +/* + * When SCSI mid-layer calls driver's reset routine, driver waits for + * MEGASAS_RESET_WAIT_TIME seconds for all outstanding IO to complete. +Note + * that the driver cannot _actually_ abort or reset pending commands. +While + * it is waiting for the commands to complete, it prints a diagnostic +message + * every MEGASAS_RESET_NOTICE_INTERVAL seconds */ +#define MEGASAS_RESET_WAIT_TIME 180 +#define MEGASAS_RESET_NOTICE_INTERVAL 5 + +#define MEGASAS_IOCTL_CMD 0 + +/* + * FW reports the maximum of number of commands that it can accept +(maximum + * commands that can be outstanding) at any time. The driver must +report a + * lower number to the mid layer because it can issue a few internal +commands + * itself (E.g, AEN, abort cmd, IOCTLs etc). The number of commands it +needs + * is shown below + */ +#define MEGASAS_INT_CMDS 32 + +/* + * FW can accept both 32 and 64 bit SGLs. We want to allocate 32/64 bit + * SGLs based on the size of dma_addr_t */ +#define IS_DMA64 (sizeof(dma_addr_t) == 8) + +#define MFI_OB_INTR_STATUS_MASK 0x00000002 +#define MFI_POLL_TIMEOUT_SECS 10 + +struct megasas_register_set { + + u32 reserved_0[4]; /*0000h */ + + u32 inbound_msg_0; /*0010h */ + u32 inbound_msg_1; /*0014h */ + u32 outbound_msg_0; /*0018h */ + u32 outbound_msg_1; /*001Ch */ + + u32 inbound_doorbell; /*0020h */ + u32 inbound_intr_status; /*0024h */ + u32 inbound_intr_mask; /*0028h */ + + u32 outbound_doorbell; /*002Ch */ + u32 outbound_intr_status; /*0030h */ + u32 outbound_intr_mask; /*0034h */ + + u32 reserved_1[2]; /*0038h */ + + u32 inbound_queue_port; /*0040h */ + u32 outbound_queue_port; /*0044h */ + + u32 reserved_2; /*004Ch */ + + u32 index_registers[1004]; /*0050h */ + +} __attribute__ ((packed)); + +struct megasas_sge32 { + + u32 phys_addr; + u32 length; + +} __attribute__ ((packed)); + +struct megasas_sge64 { + + u64 phys_addr; + u32 length; + +} __attribute__ ((packed)); + +union megasas_sgl { + + struct megasas_sge32 sge32[1]; + struct megasas_sge64 sge64[1]; + +} __attribute__ ((packed)); + +struct megasas_header { + + u8 cmd; /*00h */ + u8 sense_len; /*01h */ + u8 cmd_status; /*02h */ + u8 scsi_status; /*03h */ + + u8 target_id; /*04h */ + u8 lun; /*05h */ + u8 cdb_len; /*06h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + u32 data_xferlen; /*14h */ + +} __attribute__ ((packed)); + +union megasas_sgl_frame { + + struct megasas_sge32 sge32[8]; + struct megasas_sge64 sge64[5]; + +} __attribute__ ((packed)); + +struct megasas_init_frame { + + u8 cmd; /*00h */ + u8 reserved_0; /*01h */ + u8 cmd_status; /*02h */ + + u8 reserved_1; /*03h */ + u32 reserved_2; /*04h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 reserved_3; /*12h */ + u32 data_xfer_len; /*14h */ + + u32 queue_info_new_phys_addr_lo; /*18h */ + u32 queue_info_new_phys_addr_hi; /*1Ch */ + u32 queue_info_old_phys_addr_lo; /*20h */ + u32 queue_info_old_phys_addr_hi; /*24h */ + + u32 reserved_4[6]; /*28h */ + +} __attribute__ ((packed)); + +struct megasas_init_queue_info { + + u32 init_flags; /*00h */ + u32 reply_queue_entries; /*04h */ + + u32 reply_queue_start_phys_addr_lo; /*08h */ + u32 reply_queue_start_phys_addr_hi; /*0Ch */ + u32 producer_index_phys_addr_lo; /*10h */ + u32 producer_index_phys_addr_hi; /*14h */ + u32 consumer_index_phys_addr_lo; /*18h */ + u32 consumer_index_phys_addr_hi; /*1Ch */ + +} __attribute__ ((packed)); + +struct megasas_io_frame { + + u8 cmd; /*00h */ + u8 sense_len; /*01h */ + u8 cmd_status; /*02h */ + u8 scsi_status; /*03h */ + + u8 target_id; /*04h */ + u8 access_byte; /*05h */ + u8 reserved_0; /*06h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + u32 lba_count; /*14h */ + + u32 sense_buf_phys_addr_lo; /*18h */ + u32 sense_buf_phys_addr_hi; /*1Ch */ + + u32 start_lba_lo; /*20h */ + u32 start_lba_hi; /*24h */ + + union megasas_sgl sgl; /*28h */ + +} __attribute__ ((packed)); + +struct megasas_pthru_frame { + + u8 cmd; /*00h */ + u8 sense_len; /*01h */ + u8 cmd_status; /*02h */ + u8 scsi_status; /*03h */ + + u8 target_id; /*04h */ + u8 lun; /*05h */ + u8 cdb_len; /*06h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + u32 data_xfer_len; /*14h */ + + u32 sense_buf_phys_addr_lo; /*18h */ + u32 sense_buf_phys_addr_hi; /*1Ch */ + + u8 cdb[16]; /*20h */ + union megasas_sgl sgl; /*30h */ + +} __attribute__ ((packed)); + +struct megasas_dcmd_frame { + + u8 cmd; /*00h */ + u8 reserved_0; /*01h */ + u8 cmd_status; /*02h */ + u8 reserved_1[4]; /*03h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + + u32 data_xfer_len; /*14h */ + u32 opcode; /*18h */ + + union { /*1Ch */ + u8 b[12]; + u16 s[6]; + u32 w[3]; + } mbox; + + union megasas_sgl sgl; /*28h */ + +} __attribute__ ((packed)); + +struct megasas_abort_frame { + + u8 cmd; /*00h */ + u8 reserved_0; /*01h */ + u8 cmd_status; /*02h */ + + u8 reserved_1; /*03h */ + u32 reserved_2; /*04h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 reserved_3; /*12h */ + u32 reserved_4; /*14h */ + + u32 abort_context; /*18h */ + u32 pad_1; /*1Ch */ + + u32 abort_mfi_phys_addr_lo; /*20h */ + u32 abort_mfi_phys_addr_hi; /*24h */ + + u32 reserved_5[6]; /*28h */ + +} __attribute__ ((packed)); + +struct megasas_smp_frame { + + u8 cmd; /*00h */ + u8 reserved_1; /*01h */ + u8 cmd_status; /*02h */ + u8 connection_status; /*03h */ + + u8 reserved_2[3]; /*04h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + + u32 data_xfer_len; /*14h */ + u64 sas_addr; /*18h */ + + union { + struct megasas_sge32 sge32[2]; /* [0]: resp [1]: req */ + struct megasas_sge64 sge64[2]; /* [0]: resp [1]: req */ + } sgl; + +} __attribute__ ((packed)); + +struct megasas_stp_frame { + + u8 cmd; /*00h */ + u8 reserved_1; /*01h */ + u8 cmd_status; /*02h */ + u8 reserved_2; /*03h */ + + u8 target_id; /*04h */ + u8 reserved_3[2]; /*05h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + + u32 data_xfer_len; /*14h */ + + u16 fis[10]; /*18h */ + u32 stp_flags; + + union { + struct megasas_sge32 sge32[2]; /* [0]: resp [1]: data */ + struct megasas_sge64 sge64[2]; /* [0]: resp [1]: data */ + } sgl; + +} __attribute__ ((packed)); + +union megasas_frame { + + struct megasas_header hdr; + struct megasas_init_frame init; + struct megasas_io_frame io; + struct megasas_pthru_frame pthru; + struct megasas_dcmd_frame dcmd; + struct megasas_abort_frame abort; + struct megasas_smp_frame smp; + struct megasas_stp_frame stp; + + u8 raw_bytes[64]; +}; + +struct megasas_cmd; + +union megasas_evt_class_locale { + + struct { + u16 locale; + u8 reserved; + s8 class; + } __attribute__ ((packed)) members; + + u32 word; + +} __attribute__ ((packed)); + +struct megasas_evt_log_info { + u32 newest_seq_num; + u32 oldest_seq_num; + u32 clear_seq_num; + u32 shutdown_seq_num; + u32 boot_seq_num; + +} __attribute__ ((packed)); + +struct megasas_progress { + + u16 progress; + u16 elapsed_seconds; + +} __attribute__ ((packed)); + +struct megasas_evtarg_ld { + + u16 target_id; + u8 ld_index; + u8 reserved; + +} __attribute__ ((packed)); + +struct megasas_evtarg_pd { + u16 device_id; + u8 encl_index; + u8 slot_number; + +} __attribute__ ((packed)); + +struct megasas_evt_detail { + + u32 seq_num; + u32 time_stamp; + u32 code; + union megasas_evt_class_locale cl; + u8 arg_type; + u8 reserved1[15]; + + union { + struct { + struct megasas_evtarg_pd pd; + u8 cdb_length; + u8 sense_length; + u8 reserved[2]; + u8 cdb[16]; + u8 sense[64]; + } __attribute__ ((packed)) cdbSense; + + struct megasas_evtarg_ld ld; + + struct { + struct megasas_evtarg_ld ld; + u64 count; + } __attribute__ ((packed)) ld_count; + + struct { + u64 lba; + struct megasas_evtarg_ld ld; + } __attribute__ ((packed)) ld_lba; + + struct { + struct megasas_evtarg_ld ld; + u32 prevOwner; + u32 newOwner; + } __attribute__ ((packed)) ld_owner; + + struct { + u64 ld_lba; + u64 pd_lba; + struct megasas_evtarg_ld ld; + struct megasas_evtarg_pd pd; + } __attribute__ ((packed)) ld_lba_pd_lba; + + struct { + struct megasas_evtarg_ld ld; + struct megasas_progress prog; + } __attribute__ ((packed)) ld_prog; + + struct { + struct megasas_evtarg_ld ld; + u32 prev_state; + u32 new_state; + } __attribute__ ((packed)) ld_state; + + struct { + u64 strip; + struct megasas_evtarg_ld ld; + } __attribute__ ((packed)) ld_strip; + + struct megasas_evtarg_pd pd; + + struct { + struct megasas_evtarg_pd pd; + u32 err; + } __attribute__ ((packed)) pd_err; + + struct { + u64 lba; + struct megasas_evtarg_pd pd; + } __attribute__ ((packed)) pd_lba; + + struct { + u64 lba; + struct megasas_evtarg_pd pd; + struct megasas_evtarg_ld ld; + } __attribute__ ((packed)) pd_lba_ld; + + struct { + struct megasas_evtarg_pd pd; + struct megasas_progress prog; + } __attribute__ ((packed)) pd_prog; + + struct { + struct megasas_evtarg_pd pd; + u32 prevState; + u32 newState; + } __attribute__ ((packed)) pd_state; + + struct { + u16 vendorId; + u16 deviceId; + u16 subVendorId; + u16 subDeviceId; + } __attribute__ ((packed)) pci; + + u32 rate; + char str[96]; + + struct { + u32 rtc; + u32 elapsedSeconds; + } __attribute__ ((packed)) time; + + struct { + u32 ecar; + u32 elog; + char str[64]; + } __attribute__ ((packed)) ecc; + + u8 b[96]; + u16 s[48]; + u32 w[24]; + u64 d[12]; + } args; + + char description[128]; + +} __attribute__ ((packed)); + +struct megasas_instance { + + u32 *producer; + dma_addr_t producer_h; + u32 *consumer; + dma_addr_t consumer_h; + + u32 *reply_queue; + dma_addr_t reply_queue_h; + + unsigned long base_addr; + struct megasas_register_set __iomem *reg_set; + + s8 init_id; + u8 reserved[3]; + + u16 max_num_sge; + u16 max_fw_cmds; + u32 max_sectors_per_req; + + struct megasas_cmd **cmd_list; + struct list_head cmd_pool; + spinlock_t cmd_pool_lock; + struct dma_pool *frame_dma_pool; + struct dma_pool *sense_dma_pool; + + struct megasas_evt_detail *evt_detail; + dma_addr_t evt_detail_h; + struct megasas_cmd *aen_cmd; + struct semaphore aen_mutex; + struct semaphore ioctl_sem; + + struct Scsi_Host *host; + + wait_queue_head_t int_cmd_wait_q; + wait_queue_head_t abort_cmd_wait_q; + + struct pci_dev *pdev; + u32 unique_id; + + u32 fw_outstanding; + u32 hw_crit_error; + spinlock_t instance_lock; +}; + +#define MEGASAS_IS_LOGICAL(scp) \ + (scp->device->channel < MEGASAS_MAX_PD_CHANNELS) ? 0 : 1 + +#define MEGASAS_DEV_INDEX(inst, scp) \ + ((scp->device->channel % 2) * MEGASAS_MAX_DEV_PER_CHANNEL) + \ + scp->device->id + +struct megasas_cmd { + + union megasas_frame *frame; + dma_addr_t frame_phys_addr; + u8 *sense; + dma_addr_t sense_phys_addr; + + u32 index; + u8 sync_cmd; + u8 cmd_status; + u16 abort_aen; + + struct list_head list; + struct scsi_cmnd *scmd; + struct megasas_instance *instance; + u32 frame_count; +}; + +#define MAX_MGMT_ADAPTERS 1024 +#define MAX_IOCTL_SGE 16 + +struct megasas_iocpacket { + + u16 host_no; + u16 __pad1; + u32 sgl_off; + u32 sge_count; + u32 sense_off; + u32 sense_len; + union { + u8 raw[128]; + struct megasas_header hdr; + } frame; + + struct iovec sgl[MAX_IOCTL_SGE]; + +} __attribute__ ((packed)); + +struct megasas_aen { + u16 host_no; + u16 __pad1; + u32 seq_num; + u32 class_locale_word; +}; + +#define MEGASAS_IOC_FIRMWARE _IOWR('M', 1, struct megasas_iocpacket) +#define MEGASAS_IOC_GET_AEN _IOW('M', 2, struct megasas_aen) + +struct megasas_mgmt_info { + + u16 count; + struct megasas_instance *instance[MAX_MGMT_ADAPTERS]; + int max_index; +}; + +#endif /*LSI_MEGARAID_SAS_H */ diff -Naur scsi_misc-a/include/linux/pci_ids.h scsi_misc-b/include/linux/pci_ids.h --- scsi_misc-a/include/linux/pci_ids.h 2005-08-25 16:24:10.000000000 -0400 +++ scsi_misc-b/include/linux/pci_ids.h 2005-08-25 16:25:55.000000000 -0400 @@ -185,6 +185,7 @@ #define PCI_DEVICE_ID_LSI_61C102 0x0901 #define PCI_DEVICE_ID_LSI_63C815 0x1000 #define PCI_DEVICE_ID_LSI_SAS1064 0x0050 +#define PCI_DEVICE_ID_LSI_SAS1064R 0x0411 #define PCI_DEVICE_ID_LSI_SAS1066 0x005E #define PCI_DEVICE_ID_LSI_SAS1068 0x0054 #define PCI_DEVICE_ID_LSI_SAS1064A 0x005C @@ -554,6 +555,7 @@ #define PCI_VENDOR_ID_DELL 0x1028 #define PCI_DEVICE_ID_DELL_RACIII 0x0008 #define PCI_DEVICE_ID_DELL_RAC4 0x0012 +#define PCI_DEVICE_ID_DELL_PERC5 0x0015 #define PCI_VENDOR_ID_MATROX 0x102B #define PCI_DEVICE_ID_MATROX_MGA_2 0x0518
Attachment:
megaraid_sas_1of2.patch
Description: Binary data
- Follow-Ups:
- Prev by Date: Re: [ANNOUNCE] DSFS Network Forensic File System for Linux Patches
- Next by Date: Re: [ANNOUNCE] DSFS Network Forensic File System for Linux Patches
- Previous by thread: [-mm PATCH] v9fs: cleanup fd transport
- Next by thread: Re: FW: [Fwd: Re: [PATCH scsi-misc 2/2] megaraid_sas: LSI Logic MegaR AID SAS RA ID D river]
- Index(es):
