Hi,
I've built and installed 2.6.13 from unpatched kernel.org sources and my USB
keyboard has started to behave very strangely when I boot my system.
When I get to the login prompt, I only get to type a few key presses before the
characters stop appearing on the screen. If I unplug the keyboard and plug it in
again, the keyboard springs back into life and works perfectly until I reboot,
when the problem always occurs again. This same keyboard worked fine with
2.6.12.5 and still does.
One perhaps important fact is that the keyboard also contains two USB ports. It
is labelled Gateway and has a model ID of SK-9926. There are no devices plugged
into the ports. I don't have another USB keyboard, so I can't check whether the
presence of these ports is material.
I've rebuilt both kernels with USB debugging turned on and attach dmesg dumps
taken immediately after login. I also attach the output from lsusb -v from each
kernel. The dump from 2.6.12.5 ends immediately after a message about my
ieee1394 card, but the one from 2.6.13 continues with a USB error message
(line 276 of the dump). As far as I can see, this message is coming from hub_irq()
of drivers/usb/core/hub.c (line 314), but I have no idea why.
I'm more than happy to provide additional diagnostics and try any patches, but
please cc me as I'm not subscribed to either list.
Thanks
Chris
hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router default [1106/3099] at 0000:00:00.0
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
Initializing Cryptographic API
lp: driver loaded but no devices found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
[drm] Initialized drm 1.0.0 20040925
[drm] Initialized radeon 1.16.0 20050311 on minor 0: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xe0816000, 00:10:a7:16:aa:36, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ExcelStor Technology J360, ATA DISK drive
hdb: ExcelStor Technology J360, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST RW/DVD GCC-4521B, ATAPI CD/DVD-ROM drive
hdd: AOPEN DUW1608/ARR, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 120103200 sectors (61492 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
hdb: max request size: 1024KiB
hdb: 120103200 sectors (61492 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 hdb6 >
hdc: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:09.2: NEC Corporation USB 2.0
ehci_hcd 0000:00:09.2: reset hcs_params 0x2395 dbg=0 cc=2 pcc=3 ports=5
ehci_hcd 0000:00:09.2: reset portroute 1 0 1 0 0
ehci_hcd 0000:00:09.2: reset hcc_params 0002 thresh 0 uframes 256/512/1024
ehci_hcd 0000:00:09.2: ...powerdown ports...
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 10, io mem 0xee002000
ehci_hcd 0000:00:09.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:09.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:09.2: USB 2.0 initialized, EHCI 0.95, driver 10 Dec 2004
ehci_hcd 0000:00:09.2: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: NEC Corporation USB 2.0
usb usb1: Manufacturer: Linux 2.6.12.5 ehci_hcd
usb usb1: SerialNumber: 0000:00:09.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
hub 1-0:1.0: state 5 ports 5 chg 0000 evt 0000
ohci_hcd 0000:00:09.0: NEC Corporation USB
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 11, io mem 0xee000000
ohci_hcd 0000:00:09.0: resetting from state 'reset', control = 0x0
ohci_hcd 0000:00:09.0: OHCI controller state
ohci_hcd 0000:00:09.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:09.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:09.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:09.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:09.0: intrenable 0x8000001a MIE UE RD WDH
ohci_hcd 0000:00:09.0: fminterval a7782edf
ohci_hcd 0000:00:09.0: hcca frame #01f7
ohci_hcd 0000:00:09.0: roothub.a ff000203 POTPGT=255 NPS NDP=3
ohci_hcd 0000:00:09.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:09.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:09.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:09.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:09.0: roothub.portstatus [2] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: NEC Corporation USB
usb usb2: Manufacturer: Linux 2.6.12.5 ohci_hcd
usb usb2: SerialNumber: 0000:00:09.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 510ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
ohci_hcd 0000:00:09.0: created debug files
ohci_hcd 0000:00:09.1: NEC Corporation USB (#2)
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.1: irq 5, io mem 0xee001000
ohci_hcd 0000:00:09.1: resetting from state 'reset', control = 0x0
hub 2-0:1.0: state 5 ports 3 chg 0000 evt 0000
ohci_hcd 0000:00:09.1: OHCI controller state
ohci_hcd 0000:00:09.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:09.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:09.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:09.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:09.1: intrenable 0x8000001a MIE UE RD WDH
ohci_hcd 0000:00:09.1: fminterval a7782edf
ohci_hcd 0000:00:09.1: hcca frame #01f8
ohci_hcd 0000:00:09.1: roothub.a ff000202 POTPGT=255 NPS NDP=2
ohci_hcd 0000:00:09.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:09.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:09.1: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:09.1: roothub.portstatus [1] 0x00000100 PPS
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: NEC Corporation USB (#2)
usb usb3: Manufacturer: Linux 2.6.12.5 ohci_hcd
usb usb3: SerialNumber: 0000:00:09.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: global over-current protection
hub 3-0:1.0: power on to power good time: 510ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: no over-current condition exists
ohci_hcd 0000:00:09.1: created debug files
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:11.2: irq 10, io base 0x0000dc00
uhci_hcd 0000:00:11.2: detected 2 ports
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb4: Manufacturer: Linux 2.6.12.5 uhci_hcd
usb usb4: SerialNumber: 0000:00:11.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:11.2: port 1 portsc 009b,00
hub 4-0:1.0: port 1, status 0101, change 0003, 12 Mb/s
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:11.3: irq 10, io base 0x0000e000
uhci_hcd 0000:00:11.3: detected 2 ports
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb5: Manufacturer: Linux 2.6.12.5 uhci_hcd
usb usb5: SerialNumber: 0000:00:11.3
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.9 (Sun May 29 07:31:02 2005 UTC).
PCI: Setting latency timer of device 0000:00:11.5 to 64
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 4-1: new full speed USB device using uhci_hcd and address 2
usb 4-1: ep0 maxpacket = 8
usb 4-1: default language 0x0409
usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1: Product: SNAPSCAN
usb 4-1: Manufacturer: AGFA
usb 4-1: hotplug
usb 4-1: adding 4-1:1.0 (config #1, interface 0)
usb 4-1:1.0: hotplug
uhci_hcd 0000:00:11.2: port 2 portsc 008a,00
hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:11.3: port 1 portsc 009b,00
hub 5-0:1.0: port 1, status 0101, change 0003, 12 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 5-1: new full speed USB device using uhci_hcd and address 2
ALSA device list:
#0: VIA 8233A with CMI9738 at 0xe400, irq 5
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 15
usb 5-1: ep0 maxpacket = 8
usb 5-1: default language 0x0409
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k freed
kjournald starting. Commit interval 5 seconds
usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: Gateway Generic USB Hub
usb 5-1: Manufacturer: Silitek
usb 5-1: hotplug
usb 5-1: adding 5-1:1.0 (config #1, interface 0)
usb 5-1:1.0: hotplug
hub 5-1:1.0: usb_probe_interface
hub 5-1:1.0: usb_probe_interface - got id
hub 5-1:1.0: USB hub found
hub 5-1:1.0: 3 ports detected
hub 5-1:1.0: compound device; port removable status: FRR
hub 5-1:1.0: individual port power switching
hub 5-1:1.0: individual port over-current protection
hub 5-1:1.0: power on to power good time: 100ms
hub 5-1:1.0: hub controller current requirement: 90mA
hub 5-1:1.0: 410mA bus power budget for children
hub 5-1:1.0: enabling power on all ports
uhci_hcd 0000:00:11.3: port 2 portsc 008a,00
hub 5-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 5-1:1.0: state 5 ports 3 chg 0000 evt 0002
hub 5-1:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 5-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 5-1.1: new full speed USB device using uhci_hcd and address 3
usb 5-1.1: ep0 maxpacket = 8
usb 5-1.1: skipped 1 descriptor after interface
usb 5-1.1: default language 0x0409
usb 5-1.1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1.1: Product: Gateway Generic USB Hub
usb 5-1.1: Manufacturer: Silitek
usb 5-1.1: hotplug
usb 5-1.1: adding 5-1.1:1.0 (config #1, interface 0)
usb 5-1.1:1.0: hotplug
hub 5-1:1.0: 410mA power budget left
EXT3 FS on hda6, internal journal
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1052248k swap on /dev/hdb3. Priority:-1 extents:1
usbhid 5-1.1:1.0: usb_probe_interface
usbhid 5-1.1:1.0: usb_probe_interface - got id
input: USB HID v1.10 Keyboard [Silitek Gateway Generic USB Hub] on usb-0000:00:11.3-1.1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 212 bytes per conntrack
ohci1394: $Rev: 1250 $ Ben Collins <[email protected]>
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[ee003000-ee0037ff] Max Packet=[2048]
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 10, latency: 32, mmio: 0xee004000
bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00fffbdf [init]
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: pinnacle/mt: id=2 info="PAL+SECAM / stereo" radio=yes
bttv0: using tuner=33
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp34xx: init: chip=MSP3410G-B11 +nicam +simple +simpler +radio mode=simpler
msp34xxg: daemon started
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tda9885/6/7: chip found @ 0x86
tuner 0-0060: chip found @ 0xc0 (bt878 #0 [sw])
tuner 0-0060: microtune: companycode=4d54 part=04 rev=04
tuner 0-0060: microtune MT2032 found, OK
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00110666000013cc]
00:00:09.2: ...powerdown ports...
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 10, io mem 0xee002000
ehci_hcd 0000:00:09.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:09.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:09.2: USB 2.0 initialized, EHCI 0.95, driver 10 Dec 2004
ehci_hcd 0000:00:09.2: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: NEC Corporation USB 2.0
usb usb1: Manufacturer: Linux 2.6.13 ehci_hcd
usb usb1: SerialNumber: 0000:00:09.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
hub 1-0:1.0: state 5 ports 5 chg 0000 evt 0000
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:09.0: NEC Corporation USB
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 11, io mem 0xee000000
ohci_hcd 0000:00:09.0: resetting from state 'reset', control = 0x0
ohci_hcd 0000:00:09.0: OHCI controller state
ohci_hcd 0000:00:09.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:09.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:09.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:09.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:09.0: intrenable 0x8000001a MIE UE RD WDH
ohci_hcd 0000:00:09.0: fminterval a7782edf
ohci_hcd 0000:00:09.0: hcca frame #01ff
ohci_hcd 0000:00:09.0: roothub.a ff000203 POTPGT=255 NPS NDP=3
ohci_hcd 0000:00:09.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:09.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:09.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:09.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:09.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:09.0: created debug files
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: NEC Corporation USB
usb usb2: Manufacturer: Linux 2.6.13 ohci_hcd
usb usb2: SerialNumber: 0000:00:09.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 510ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: state 5 ports 3 chg 0000 evt 0000
ohci_hcd 0000:00:09.1: NEC Corporation USB (#2)
ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:09.1: irq 5, io mem 0xee001000
ohci_hcd 0000:00:09.1: resetting from state 'reset', control = 0x0
ohci_hcd 0000:00:09.1: OHCI controller state
ohci_hcd 0000:00:09.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:09.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:09.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:09.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:09.1: intrenable 0x8000001a MIE UE RD WDH
ohci_hcd 0000:00:09.1: fminterval a7782edf
ohci_hcd 0000:00:09.1: hcca frame #01ff
ohci_hcd 0000:00:09.1: roothub.a ff000202 POTPGT=255 NPS NDP=2
ohci_hcd 0000:00:09.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:09.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:09.1: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:09.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:09.1: created debug files
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: NEC Corporation USB (#2)
usb usb3: Manufacturer: Linux 2.6.13 ohci_hcd
usb usb3: SerialNumber: 0000:00:09.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: global over-current protection
hub 3-0:1.0: power on to power good time: 510ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: no over-current condition exists
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0000
USB Universal Host Controller Interface driver v2.3
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:11.2: detected 2 ports
uhci_hcd 0000:00:11.2: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:11.2: Performing full reset
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:11.2: irq 10, io base 0x0000dc00
uhci_hcd 0000:00:11.2: supports USB remote wakeup
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb4: Manufacturer: Linux 2.6.13 uhci_hcd
usb usb4: SerialNumber: 0000:00:11.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:11.2: port 1 portsc 009b,00
hub 4-0:1.0: port 1, status 0101, change 0003, 12 Mb/s
uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:11.3: detected 2 ports
uhci_hcd 0000:00:11.3: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:11.3: Performing full reset
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:11.3: irq 10, io base 0x0000e000
uhci_hcd 0000:00:11.3: supports USB remote wakeup
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb5: Manufacturer: Linux 2.6.13 uhci_hcd
usb usb5: SerialNumber: 0000:00:11.3
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.9b (Thu Jul 28 12:20:13 2005 UTC).
PCI: Setting latency timer of device 0000:00:11.5 to 64
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 4-1: new full speed USB device using uhci_hcd and address 2
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
usb 4-1: ep0 maxpacket = 8
usb 4-1: default language 0x0409
usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1: Product: SNAPSCAN
usb 4-1: Manufacturer: AGFA
usb 4-1: hotplug
usb 4-1: adding 4-1:1.0 (config #1, interface 0)
usb 4-1:1.0: hotplug
uhci_hcd 0000:00:11.2: port 2 portsc 008a,00
hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:11.3: port 1 portsc 009b,00
hub 5-0:1.0: port 1, status 0101, change 0003, 12 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
ALSA device list:
#0: VIA 8233A with CMI9738 at 0xe400, irq 5
NET: Registered protocol family 2
usb 5-1: new full speed USB device using uhci_hcd and address 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI Shortcut mode
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 164k freed
kjournald starting. Commit interval 5 seconds
usb 5-1: ep0 maxpacket = 8
usb 5-1: default language 0x0409
usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: Gateway Generic USB Hub
usb 5-1: Manufacturer: Silitek
usb 5-1: hotplug
usb 5-1: adding 5-1:1.0 (config #1, interface 0)
usb 5-1:1.0: hotplug
hub 5-1:1.0: usb_probe_interface
hub 5-1:1.0: usb_probe_interface - got id
hub 5-1:1.0: USB hub found
hub 5-1:1.0: 3 ports detected
hub 5-1:1.0: compound device; port removable status: FRR
hub 5-1:1.0: individual port power switching
hub 5-1:1.0: individual port over-current protection
hub 5-1:1.0: power on to power good time: 100ms
hub 5-1:1.0: hub controller current requirement: 90mA
hub 5-1:1.0: 410mA bus power budget for children
hub 5-1:1.0: enabling power on all ports
uhci_hcd 0000:00:11.3: port 2 portsc 008a,00
hub 5-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 5-1:1.0: state 5 ports 3 chg 0000 evt 0002
hub 5-1:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 5-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 5-1.1: new full speed USB device using uhci_hcd and address 3
usb 5-1.1: ep0 maxpacket = 8
usb 5-1.1: skipped 1 descriptor after interface
usb 5-1.1: default language 0x0409
usb 5-1.1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1.1: Product: Gateway Generic USB Hub
usb 5-1.1: Manufacturer: Silitek
usb 5-1.1: hotplug
usb 5-1.1: adding 5-1.1:1.0 (config #1, interface 0)
usb 5-1.1:1.0: hotplug
hub 5-1:1.0: 410mA power budget left
EXT3 FS on hda6, internal journal
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usbhid 5-1.1:1.0: usb_probe_interface
usbhid 5-1.1:1.0: usb_probe_interface - got id
input: USB HID v1.10 Keyboard [Silitek Gateway Generic USB Hub] on usb-0000:00:11.3-1.1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Adding 1052248k swap on /dev/hdb3. Priority:-1 extents:1
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 212 bytes per conntrack
ohci1394: $Rev: 1299 $ Ben Collins <[email protected]>
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[ee003000-ee0037ff] Max Packet=[2048]
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 10, latency: 32, mmio: 0xee004000
bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00fffbdf [init]
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: pinnacle/mt: id=2 info="PAL+SECAM / stereo" radio=yes
bttv0: using tuner=33
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp34xx: init: chip=MSP3410G-B11 +nicam +simple +simpler +radio mode=simpler
msp34xxg: daemon started
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tda9885/6/7: chip found @ 0x86
: chip found @ 0xc0 (bt878 #0 [sw])
: Returned more than 5 bytes. It is not a TEA5767
tuner 0-0060: microtune: companycode=4d54 part=04 rev=04
tuner 0-0060: microtune MT2032 found, OK
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00110666000013cc]
hub 5-1:1.0: transfer --> -75
hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:11.3: port 1 portsc 008a,00
hub 5-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 5-1: USB disconnect, address 2
usb 5-1.1: USB disconnect, address 3
usb 5-1.1: usb_disable_device nuking all URBs
usb 5-1.1: unregistering interface 5-1.1:1.0
usb 5-1.1:1.0: hotplug
usb 5-1.1: unregistering device
usb 5-1.1: hotplug
usb 5-1: usb_disable_device nuking all URBs
uhci_hcd 0000:00:11.3: shutdown urb dfc2a560 pipe 40408280 ep1in-intr
usb 5-1: unregistering interface 5-1:1.0
usb 5-1:1.0: hotplug
usb 5-1: unregistering device
usb 5-1: hotplug
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:11.3: suspend_rh (auto-stop)
uhci_hcd 0000:00:11.3: wakeup_rh (auto-start)
hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:11.3: port 1 portsc 0093,00
hub 5-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 5-1: new full speed USB device using uhci_hcd and address 4
usb 5-1: ep0 maxpacket = 8
usb 5-1: default language 0x0409
usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: Gateway Generic USB Hub
usb 5-1: Manufacturer: Silitek
usb 5-1: hotplug
usb 5-1: adding 5-1:1.0 (config #1, interface 0)
usb 5-1:1.0: hotplug
hub 5-1:1.0: usb_probe_interface
hub 5-1:1.0: usb_probe_interface - got id
hub 5-1:1.0: USB hub found
hub 5-1:1.0: 3 ports detected
hub 5-1:1.0: compound device; port removable status: FRR
hub 5-1:1.0: individual port power switching
hub 5-1:1.0: individual port over-current protection
hub 5-1:1.0: power on to power good time: 100ms
hub 5-1:1.0: hub controller current requirement: 90mA
hub 5-1:1.0: 410mA bus power budget for children
hub 5-1:1.0: enabling power on all ports
hub 5-1:1.0: state 5 ports 3 chg 0000 evt 0000
hub 5-1:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 5-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 5-1.1: new full speed USB device using uhci_hcd and address 5
usb 5-1.1: ep0 maxpacket = 8
usb 5-1.1: skipped 1 descriptor after interface
usb 5-1.1: default language 0x0409
usb 5-1.1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1.1: Product: Gateway Generic USB Hub
usb 5-1.1: Manufacturer: Silitek
usb 5-1.1: hotplug
usb 5-1.1: adding 5-1.1:1.0 (config #1, interface 0)
usb 5-1.1:1.0: hotplug
usbhid 5-1.1:1.0: usb_probe_interface
usbhid 5-1.1:1.0: usb_probe_interface - got id
input: USB HID v1.10 Keyboard [Silitek Gateway Generic USB Hub] on usb-0000:00:11.3-1.1
hub 5-1:1.0: 410mA power budget left
Bus 005 Device 003: ID 0443:001c Gateway, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0443 Gateway, Inc.
idProduct 0x001c
bcdDevice 1.00
iManufacturer 1 Silitek
iProduct 2 Gateway Generic USB Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 2 Gateway Generic USB Hub
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 2 Gateway Generic USB Hub
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 65
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 24
Bus 005 Device 002: ID 0443:001d Gateway, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0443 Gateway, Inc.
idProduct 0x001d
bcdDevice 1.00
iManufacturer 1 Silitek
iProduct 2 Gateway Generic USB Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 2 Gateway Generic USB Hub
bmAttributes 0xa0
Remote Wakeup
MaxPower 90mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 2 Gateway Generic USB Hub
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x000d
Per-port power switching
Compound device
Per-port overcurrent protection
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 90 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Bus 005 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12.5 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
iSerial 1 0000:00:11.3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Bus 004 Device 002: ID 06bd:2061 AGFA-Gevaert NV SnapScan 1212U (?)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 8
idVendor 0x06bd AGFA-Gevaert NV
idProduct 0x2061 SnapScan 1212U (?)
bcdDevice 1.00
iManufacturer 1 AGFA
iProduct 2 SNAPSCAN
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 16
Bus 004 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12.5 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
iSerial 1 0000:00:11.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Bus 003 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12.5 ohci_hcd
iProduct 2 NEC Corporation USB (#2)
iSerial 1 0000:00:09.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 255 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12.5 ohci_hcd
iProduct 2 NEC Corporation USB
iSerial 1 0000:00:09.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 255 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.12.5 ehci_hcd
iProduct 2 NEC Corporation USB 2.0
iSerial 1 0000:00:09.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 5
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Bus 005 Device 005: ID 0443:001c Gateway, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0443 Gateway, Inc.
idProduct 0x001c
bcdDevice 1.00
iManufacturer 1 Silitek
iProduct 2 Gateway Generic USB Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 2 Gateway Generic USB Hub
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 2 Gateway Generic USB Hub
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 65
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 24
Bus 005 Device 004: ID 0443:001d Gateway, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0443 Gateway, Inc.
idProduct 0x001d
bcdDevice 1.00
iManufacturer 1 Silitek
iProduct 2 Gateway Generic USB Hub
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 2 Gateway Generic USB Hub
bmAttributes 0xa0
Remote Wakeup
MaxPower 90mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 2 Gateway Generic USB Hub
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x000d
Per-port power switching
Compound device
Per-port overcurrent protection
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 90 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Bus 005 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.13 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
iSerial 1 0000:00:11.3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Bus 004 Device 002: ID 06bd:2061 AGFA-Gevaert NV SnapScan 1212U (?)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 8
idVendor 0x06bd AGFA-Gevaert NV
idProduct 0x2061 SnapScan 1212U (?)
bcdDevice 1.00
iManufacturer 1 AGFA
iProduct 2 SNAPSCAN
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x40
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 16
Bus 004 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.13 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
iSerial 1 0000:00:11.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Bus 003 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.13 ohci_hcd
iProduct 2 NEC Corporation USB (#2)
iSerial 1 0000:00:09.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 255 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.13 ohci_hcd
iProduct 2 NEC Corporation USB
iSerial 1 0000:00:09.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 255 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.13 ehci_hcd
iProduct 2 NEC Corporation USB 2.0
iSerial 1 0000:00:09.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 5
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x00
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
| |
 |