SCSI- unexpected disconnect with kernel-2.6.13-r6

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



I am using a LSIU160/Symbios 53c1010 Ultra3 scsi adapter and it works at full speed (75 MB/sec) with kernel-2.6.12. And dmesg shows:

kernel:  target0:0:0: Beginning Domain Validation
kernel:  target0:0:0: asynchronous.
kernel: WIDTH IS 1
kernel:  target0:0:0: wide asynchronous.
kernel:  target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
kernel:  target0:0:0: Ending Domain Validation
kernel: sym1: <1010-33> rev 0x1 at pci 0000:01:07.1 irq 11
kernel: sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
kernel: sym1: open drain IRQ line driver
kernel: sym1: using LOAD/STORE-based firmware.
kernel: sym1: handling phase mismatch from SCRIPTS.
kernel: sym1: SCSI BUS has been reset.
kernel: scsi1 : sym-2.2.0
kernel: libata version 1.11 loaded.

With kernel-2.6.13-r6 the speed drops back to 2.70 MB/sec because of
validation failure and dmesg shows:

kernel:  target0:0:0: Beginning Domain Validation
kernel:  target0:0:0: asynchronous.
kernel:  target0:0:0: wide asynchronous.
kernel:  target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS (
kernel: sym0: unexpected disconnect
kernel:  target0:0:0: Write Buffer failure 700ff
kernel:  target0:0:0: Domain Validation Disabing Information units
kernel:  0:0:0:0: phase change 6-7 11@3fb3c3a8 resid=10.
kernel:  target0:0:0: asynchronous.
kernel: sym0: unexpected disconnect
target0:0:0: Write Buffer failure 700ff
target0:0:0: Domain Validation detected failure, dropping back
kernel:  target0:0:0: asynchronous.
target0:0:0: Ending Domain Validation
kernel: sym1: <1010-33> rev 0x1 at pci 0000:01:07.1 irq 11
kernel: sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checkingkernel: sym1:
open drain IRQ line driver, using on-chip SRAM
kernel: sym1: using LOAD/STORE-based firmware.
kernel: sym1: handling phase mismatch from SCRIPTS.
kernel: sym1: SCSI BUS has been reset.
kernel: scsi1 : sym-2.2.1
kernel: libata version 1.11 loaded.

The kernel config has:

CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]
  Powered by Linux