The "hdparm -I /dev/hdc"
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
de: failed opcode was: 0xec
Is present on all kernels that I have locally (oldest 2.6.11.11)
so it is not related to the threadstarters problems, it seems.
root:sleipner:~# hdparm -I /dev/hdc
/dev/hdc:
ATAPI CD-ROM, with removable media
Model Number: TSSTcorpCD/DVDW TS-L532A
Serial Number: 254A204626
Firmware Revision: TI50
Standards:
Used: ATAPI for CD-ROMs, SFF-8020i, r2.5
Supported: CD-ROM ATAPI-2
Configuration:
DRQ response: 50us.
Packet size: 12 bytes
Capabilities:
LBA, IORDY(can be disabled)
Buffer size: 2048.0kB
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* DEVICE RESET cmd
* PACKET command feature set
* Power Management feature set
* Mandatory FLUSH CACHE command
HW reset results:
CBLID- above Vih
Device num = 0 determined by CSEL
root:sleipner:~# hdparm -i /dev/hdc
/dev/hdc:
Model=TSSTcorpCD/DVDW TS-L532A, FwRev=TI50, SerialNo=254A204626
Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=2048kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no
Drive conforms to: Reserved:
* signifies the current active mode
root:sleipner:~# hdparm /dev/hdc
/dev/hdc:
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
HDIO_GETGEO failed: Invalid argument
root:sleipner:~# grep VIA /usr/src/testing/my-2.6.13-rc6-.config
[edited]
CONFIG_BLK_DEV_VIA82CXXX=y
root:sleipner:~# grep IDE /usr/src/testing/my-2.6.13-rc6-.config
[edited]
# CONFIG_PARIDE is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# Please see Documentation/ide.txt for help/info on IDE drives
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
# IDE chipset support/bugfixes
# CONFIG_IDE_GENERIC is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
Mvh
Mats Johannesson
--
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
| |
 |