Hello,
Whenever I reboot my Linux machine it turns itself off in the end,
unless I add the 'acpi=off' to the end of kernel command line on boot.
Apparently, it happens after unmounting filesystems as it doesn't do
fsck after next power-up.
The Kernel is 2.6.13-pre6
The machine itself is a dual CPU P3 system with MSI-694D motherboard
(VIA chipset) with onboard promise controller, via-rhine network card
and Symbios Logic 53c875 SCSI card.
Here is a dmesg of 2.6.13-rc6 booted with acpi=off
----Linux version 2.6.13-rc6 (masouds@dual) (gcc version 3.3.5 (Debian
1:3.3.5-8ubu5
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002fff0000 (usable)
BIOS-e820: 000000002fff0000 - 000000002fff3000 (ACPI NVS)
BIOS-e820: 000000002fff3000 - 0000000030000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
767MB LOWMEM available.
found SMP MP-table at 000f5fd0
On node 0 totalpages: 196592
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 192496 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 6:8 APIC version 17
Processor #1 6:8 APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Allocating PCI resources starting at 30000000 (gap: 30000000:cec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro console=ttyS0,9600n8 console=tty0
CONSOLf
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 868.996 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 773796k/786368k available (3035k kernel code, 12064k reserved,
1240k da)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1739.69 BogoMIPS
(lpj=869848)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
000000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
00000000 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000
0000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 0a
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1737.01 BogoMIPS
(lpj=868508)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
000000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
00000000 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000
0000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 0a
Total of 2 processors activated (3476.71 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=0
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb2c0, last bus=1
PCI: Using configuration type 1
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20050408
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0
PCI->APIC IRQ transform: 0000:00:07.2[D] -> IRQ 7
PCI->APIC IRQ transform: 0000:00:07.3[D] -> IRQ 7
PCI->APIC IRQ transform: 0000:00:0e.0[A] -> IRQ 11
PCI->APIC IRQ transform: 0000:00:12.0[A] -> IRQ 5
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: d0000000-d3ffffff
PREFETCH window: d4000000-d5ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
audit: initializing netlink socket (disabled)
audit(1123779736.430:1): initialized
Installing knfsd (copyright (C) 1996 [email protected]).
Initializing Cryptographic API
PCI: Enabling Via external APIC routing
lp: driver loaded but no devices found
Real Time Clock Driver v1.12
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60
sec (no)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: AGP aperture is 256M @ 0xc0000000
[drm] Initialized drm 1.0.0 20040925
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin
is 60 se.
Hangcheck: Using monotonic_clock().
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x0
parport_pc: VIA parallel port disabled in BIOS
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
loop: loaded (max 8 devices)
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
eth0: VIA Rhine II at 0x1e400, 00:05:5d:f3:76:65, IRQ 5.
eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 45e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD1600BB-22GUA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface
ide1...
hdd: IRQ probe failed
(0xffffbefa)
hdd: CD-ROM CDU611-F, ATAPI CD/DVD-ROM
drive
ide1 at 0x170-0x177,0x376 on irq
15
hda: max request size:
1024KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63,
UDMA(100)
hda: cache flushes
supported
hda: hda1 hda2 hda3
hda4
hda4: <openbsd: hda5 hda6
>
hdd: ATAPI 10X CD-ROM drive, 256kB
Cache
Uniform CD-ROM driver Revision:
3.20
sym0: <875> rev 0x26 at pci 0000:00:0e.0 irq
11
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity
checking
sym0: SCSI BUS has been
reset.
scsi0 :
sym-2.2.1
usbmon: debugs is not
available
USB Universal Host Controller Interface driver
v2.3
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number
1
uhci_hcd 0000:00:07.2: irq 7, io base
0x0000b400
hub 1-0:1.0: USB hub
found
hub 1-0:1.0: 2 ports
detected
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller)
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number
2
uhci_hcd 0000:00:07.3: irq 7, io base
0x0000b800
hub 2-0:1.0: USB hub
found
hub 2-0:1.0: 2 ports
detected
usbcore: registered new driver
usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class
driver
Initializing USB Mass Storage
driver...
usb 2-2: new full speed USB device using uhci_hcd and address
2
usbcore: registered new driver
usb-storage
USB Mass Storage support
registered.
usbcore: registered new driver
usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core
driver
usbcore: registered new driver
usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for
Generic
usbcore: registered new driver
usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
v2.0
mice: PS/2 mouse device common for all
mice
oprofile: using NMI
interrupt.
input: AT Translated Set 2 keyboard on
isa0060/serio0
NET: Registered protocol family
2
IP route cache hash table entries: 32768 (order: 5, 131072
bytes)
TCP established hash table entries: 131072 (order: 9, 2097152
bytes)
input: ImExPS/2 Generic Explorer Mouse on
isa0060/serio1
TCP bind hash table entries: 65536 (order: 7, 786432
bytes)
TCP: Hash tables configured (established 131072 bind
65536)
TCP reno
registered
ip_conntrack version 2.1 (6143 buckets, 49144 max) - 212 bytes per
conntrack
ip_tables: (C) 2000-2002 Netfilter core
team
ipt_recent v0.3.1: Stephen Frost <[email protected]>.
http://snowman.net/proj/
arp_tables: (C) 2002 David S.
Miller
TCP bic
registered
NET: Registered protocol family
1
NET: Registered protocol family
17
Starting
balanced_irq
Using IPI Shortcut
mode
EXT3-fs: INFO: recovery required on readonly
filesystem.
EXT3-fs: write access will be enabled during
recovery.
EXT3-fs: recovery
complete.
kjournald starting. Commit interval 5
seconds
EXT3-fs: mounted filesystem with ordered data
mode.
VFS: Mounted root (ext3 filesystem)
readonly.
Freeing unused kernel memory: 248k
freed
Adding 996020k swap on /dev/hda2. Priority:-1
extents:1
EXT3 FS on hda1, internal
journal
device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
[email protected]
md: md driver 0.90.2 MAX_MD_DEVS=256,
MD_SB_DISKS=27
md: bitmap version 3.38device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: dm-linear: Device lookup failed
device-mapper: error adding target to table
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
---
Without acpi=off, I get:
----
Linux version 2.6.13-rc6 (masouds@dual) (gcc version 3.3.5 (Debian
1:3.3.5-8ubu5
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002fff0000 (usable)
BIOS-e820: 000000002fff0000 - 000000002fff3000 (ACPI NVS)
BIOS-e820: 000000002fff3000 - 0000000030000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
767MB LOWMEM available.
found SMP MP-table at 000f5fd0
On node 0 totalpages: 196592
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 192496 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VIA694 ) @ 0x000f78c0
ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2fff3040
ACPI: MADT (v001 VIA694 0x00000000 0x00000000) @ 0x2fff5740
ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:8 APIC version 17
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 30000000:cec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro console=ttyS0,9600n8 console=tty0
CONSOL0
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 868.784 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 773796k/786368k available (3035k kernel code, 12064k reserved,
1240k da)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1739.65 BogoMIPS
(lpj=869828)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
000000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
00000000 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000
0000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 0a
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1737.10 BogoMIPS
(lpj=868551)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
000000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
00000000 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000
0000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 0a
Total of 2 processors activated (3476.75 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb2c0, last bus=1
PCI: Using configuration type 1
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: d0000000-d3ffffff
PREFETCH window: d4000000-d5ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
audit: initializing netlink socket (disabled)
audit(1123780637.933:1): initialized
Installing knfsd (copyright (C) 1996 [email protected]).
Initializing Cryptographic API
PCI: Enabling Via external APIC routing
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1])
ACPI: CPU1 (power states: C1[C1])
lp: driver loaded but no devices found
Real Time Clock Driver v1.12
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60
sec (no)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: AGP aperture is 256M @ 0xc0000000
[drm] Initialized drm 1.0.0 20040925
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin
is 60 se.
Hangcheck: Using monotonic_clock().
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x0
parport_pc: VIA parallel port disabled in BIOS
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
loop: loaded (max 8 devices)
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Via IRQ fixup for 0000:00:12.0, from 5 to 0
eth0: VIA Rhine II at 0x1e400, 00:05:5d:f3:76:65, IRQ 16.
eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 45e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD1600BB-22GUA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: CD-ROM CDU611-F, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hda4: <openbsd: hda5 hda6 >
hdd: ATAPI 10X CD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 16 (level, low) -> IRQ 17
sym0: <875> rev 0x26 at pci 0000:00:0e.0 irq 17
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.1
usbmon: debugs is not available
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level,
low) -> IR1
PCI: Via IRQ fixup for 0000:00:07.2, from 7 to 11
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000b400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level,
low) -> IR1
PCI: Via IRQ fixup for 0000:00:07.3, from 7 to
11
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller)
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number
2
uhci_hcd 0000:00:07.3: irq 11, io base
0x0000b800
hub 2-0:1.0: USB hub
found
hub 2-0:1.0: 2 ports
detected
usb 2-2: new full speed USB device using uhci_hcd and address
2
usbcore: registered new driver
usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class
driver
Initializing USB Mass Storage
driver...
usbcore: registered new driver
usb-storage
USB Mass Storage support
registered.
usbcore: registered new driver
usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core
driver
usbcore: registered new driver
usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for
Generic
usbcore: registered new driver
usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
v2.0
mice: PS/2 mouse device common for all
mice
oprofile: using NMI
interrupt.
input: AT Translated Set 2 keyboard on
isa0060/serio0
NET: Registered protocol family
2
IP route cache hash table entries: 32768 (order: 5, 131072
bytes)
TCP established hash table entries: 131072 (order: 9, 2097152
bytes)
input: ImExPS/2 Generic Explorer Mouse on
isa0060/serio1
TCP bind hash table entries: 65536 (order: 7, 786432
bytes)
TCP: Hash tables configured (established 131072 bind
65536)
TCP reno
registered
ip_conntrack version 2.1 (6143 buckets, 49144 max) - 212 bytes per
conntrack
ip_tables: (C) 2000-2002 Netfilter core
team
ipt_recent v0.3.1: Stephen Frost <[email protected]>.
http://snowman.net/proj/
arp_tables: (C) 2002 David S.
Miller
TCP bic
registered
NET: Registered protocol family
1
NET: Registered protocol family
17
Starting
balanced_irq
Using IPI Shortcut
mode
EXT3-fs: mounted filesystem with ordered data
mode.
VFS: Mounted root (ext3 filesystem)
readonly.
kjournald starting. Commit interval 5
seconds
Freeing unused kernel memory: 248k
freed
Adding 996020k swap on /dev/hda2. Priority:-1
extents:1
EXT3 FS on hda1, internal
journal
device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
[email protected]
md: md driver 0.90.2 MAX_MD_DEVS=256,
MD_SB_DISKS=27
md: bitmap version
3.38
cdrom: open
failed.
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
device-mapper: dm-linear: Device lookup
failed
device-mapper: error adding target to
table
eth0: link up, 100Mbps, full-duplex, lpa
0x45E1
ibm_acpi: acpi_evalf(DHKC, d, ...) failed:
4097
ibm_acpi: `enable,0xffff' invalid for parameter `hotkey'
----
My config is available at http://masoud.ir/config-2.6.txt for those
interested.
Any ideas?
cheers,
Masoud
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
| |
 |