>-----Original Message-----
>From: [email protected]
>[mailto:[email protected]] On Behalf Of
>[email protected]
>Sent: Sunday, July 31, 2005 7:02 PM
>To: [email protected]
>Cc: [email protected];
>[email protected]; [email protected]; [email protected]
>Subject: Re: [linux-usb-devel] Re: 2.6.13-rc4-mm1
>
>> Date: Sun, 31 Jul 2005 16:02:44 -0700
>> From: Greg KH <[email protected]>
>>
>> On Sun, Jul 31, 2005 at 11:25:10AM -0700, [email protected] wrote:
>> > I think that "continuing" codepath came from someone at
>Phoenix, FWIW;
That was me.
>> > the problem is that I see the PCI quirks code has evolved
>even farther
>> > from the main copy of the init code in the USB tree. Sigh.
>>
>> I don't like that either, but can't think of a way to make
>it easier to
>> keep them in sync. Can you?
Major problem here is that handoff may be necessary even if whole
USB support is disabled in config. I was thinking of integrating them
into
USB code somehow, but did not have enough time for it, sorry :(
>
>Sure. The problem as I see it is that there are two copies, and one
>of them isn't in the USB part of the tree. So just move it, and cope
>with the consequences during the 2.6.14 cycle:
>
> (a) Move the USB quirks out of the generic PCI drivers directory
> into the USB HCD directory (see the attached patch);
>
> (b) foreach HCD in (ehci ohci uhci) do:
>
> (1) Merge the two different routines: HCD internal init/reset
> and the PCI quirk code are identical in intent, but they
> each address different sets of quirks.
>
> (2) Then the HCD reset() and PCI quirk() code will call those
> single shared routine.
>
Agree, but at least:
- drivers/Makefile & drivers/usb/Makefile have to be modified as well
to include
quirks on CONFIG_PCI
- Constants like EHCI_USBCMD_RUN should probably be replaced with
'native' usb code ones.
Thanks,
Aleks.
>
>At OLS, Vojtech mentioned wanting to make "usb-handoff" be the default.
>That's seem plausible (USB has more than its fair share of
>BIOS issues!)
>but should only kick in sometime after we merge the two different sets
>of quirk handling logic.
>
>- Dave
>
>
>
>This moves the PCI quirk handling for USB host controllers from the
>PCI directory to the USB directory.
>
>Follow-on patches will need to remove code duplication, and probably
>make "usb-handoff" be the system default.
>
>Compile-tested only so far.
>
>Signed-off-by: David Brownell <[email protected]>
>
>--- g26.orig/drivers/usb/host/Makefile 2005-06-28
>19:23:13.000000000 -0700
>+++ g26/drivers/usb/host/Makefile 2005-07-31
>18:41:35.000000000 -0700
>@@ -1,8 +1,9 @@
> #
>-# Makefile for USB Host Controller Driver
>-# framework and drivers
>+# Makefile for USB Host Controller Drivers
> #
>
>+obj-$(CONFIG_PCI) += pci-quirks.o
>+
> obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
> obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
> obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o
>--- /dev/null 1970-01-01 00:00:00.000000000 +0000
>+++ g26/drivers/usb/host/pci-quirks.c 2005-07-31
>17:33:38.000000000 -0700
>@@ -0,0 +1,279 @@
>+/*
>+ * This file contains work-arounds for many known PCI
>hardware and BIOS
>+ * quirks relating to USB host controllers.
>+ *
>+ * There are a lot of those, especially on hardware that needs to work
>+ * with USB mice and keyboard for booting. And this code
>needs to fire
>+ * early; before the input subsystem gets initialized, and while BIOS
>+ * (or SMI) code has few problems running.
>+ *
>+ * They're collected here since USB host controller drivers
>need to use
>+ * the same code as part of hardware initialization.
>+ *
>+ * Copyright (c) 1999 Martin Mares <[email protected]>
>+ * (and others)
>+ */
>+
>+#include <linux/config.h>
>+#include <linux/types.h>
>+#include <linux/kernel.h>
>+#include <linux/pci.h>
>+#include <linux/init.h>
>+#include <linux/delay.h>
>+#include <linux/acpi.h>
>+
>+// #include "pci.h"
>+
>+/*
>+ * PIIX3 USB: We have to disable USB interrupts that are
>+ * hardwired to PIRQD# and may be shared with an
>+ * external device.
>+ *
>+ * Legacy Support Register (LEGSUP):
>+ * bit13: USB PIRQ Enable (USBPIRQDEN),
>+ * bit4: Trap/SMI On IRQ Enable (USBSMIEN).
>+ *
>+ * We mask out all r/wc bits, too.
>+ */
>+static void __devinit quirk_piix3_usb(struct pci_dev *dev)
>+{
>+ u16 legsup;
>+
>+ pci_read_config_word(dev, 0xc0, &legsup);
>+ legsup &= 0x50ef;
>+ pci_write_config_word(dev, 0xc0, legsup);
>+}
>+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,
>PCI_DEVICE_ID_INTEL_82371SB_2, quirk_piix3_usb );
>+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,
>PCI_DEVICE_ID_INTEL_82371AB_2, quirk_piix3_usb );
>+
>+
>+/* FIXME this should be the same code that the USB controllers use...
>+ * the hcd->reset() method basically does this.
>+ */
>+
>+#define UHCI_USBLEGSUP 0xc0 /*
>legacy support */
>+#define UHCI_USBCMD 0 /* command register */
>+#define UHCI_USBSTS 2 /* status register */
>+#define UHCI_USBINTR 4 /* interrupt register */
>+#define UHCI_USBLEGSUP_DEFAULT 0x2000 /* only
>PIRQ enable set */
>+#define UHCI_USBCMD_RUN (1 << 0) /*
>RUN/STOP bit */
>+#define UHCI_USBCMD_GRESET (1 << 2) /* Global reset */
>+#define UHCI_USBCMD_CONFIGURE (1 << 6) /* config semaphore */
>+#define UHCI_USBSTS_HALTED (1 << 5) /* HCHalted bit */
>+
>+#define OHCI_CONTROL 0x04
>+#define OHCI_CMDSTATUS 0x08
>+#define OHCI_INTRSTATUS 0x0c
>+#define OHCI_INTRENABLE 0x10
>+#define OHCI_INTRDISABLE 0x14
>+#define OHCI_OCR (1 << 3) /* ownership
>change request */
>+#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */
>+#define OHCI_INTR_OC (1 << 30) /* ownership change */
>+
>+#define EHCI_HCC_PARAMS 0x08 /*
>extended capabilities */
>+#define EHCI_USBCMD 0 /* command register */
>+#define EHCI_USBCMD_RUN (1 << 0) /*
>RUN/STOP bit */
>+#define EHCI_USBSTS 4 /* status register */
>+#define EHCI_USBSTS_HALTED (1 << 12) /* HCHalted bit */
>+#define EHCI_USBINTR 8 /* interrupt register */
>+#define EHCI_USBLEGSUP 0 /*
>legacy support register */
>+#define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */
>+#define EHCI_USBLEGSUP_OS (1 << 24) /* OS semaphore */
>+#define EHCI_USBLEGCTLSTS 4 /* legacy
>control/status */
>+#define EHCI_USBLEGCTLSTS_SOOE (1 << 13) /* SMI
>on ownership change */
>+
>+int usb_early_handoff __devinitdata = 0;
>+static int __init usb_handoff_early(char *str)
>+{
>+ usb_early_handoff = 1;
>+ return 0;
>+}
>+__setup("usb-handoff", usb_handoff_early);
>+
>+static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
>+{
>+ unsigned long base = 0;
>+ int wait_time, delta;
>+ u16 val, sts;
>+ int i;
>+
>+ for (i = 0; i < PCI_ROM_RESOURCE; i++)
>+ if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
>+ base = pci_resource_start(pdev, i);
>+ break;
>+ }
>+
>+ if (!base)
>+ return;
>+
>+ /*
>+ * stop controller
>+ */
>+ sts = inw(base + UHCI_USBSTS);
>+ val = inw(base + UHCI_USBCMD);
>+ val &= ~(u16)(UHCI_USBCMD_RUN | UHCI_USBCMD_CONFIGURE);
>+ outw(val, base + UHCI_USBCMD);
>+
>+ /*
>+ * wait while it stops if it was running
>+ */
>+ if ((sts & UHCI_USBSTS_HALTED) == 0)
>+ {
>+ wait_time = 1000;
>+ delta = 100;
>+
>+ do {
>+ outw(0x1f, base + UHCI_USBSTS);
>+ udelay(delta);
>+ wait_time -= delta;
>+ val = inw(base + UHCI_USBSTS);
>+ if (val & UHCI_USBSTS_HALTED)
>+ break;
>+ } while (wait_time > 0);
>+ }
>+
>+ /*
>+ * disable interrupts & legacy support
>+ */
>+ outw(0, base + UHCI_USBINTR);
>+ outw(0x1f, base + UHCI_USBSTS);
>+ pci_read_config_word(pdev, UHCI_USBLEGSUP, &val);
>+ if (val & 0xbf)
>+ pci_write_config_word(pdev, UHCI_USBLEGSUP,
>UHCI_USBLEGSUP_DEFAULT);
>+
>+}
>+
>+static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
>+{
>+ void __iomem *base;
>+ int wait_time;
>+
>+ base = ioremap_nocache(pci_resource_start(pdev, 0),
>+ pci_resource_len(pdev, 0));
>+ if (base == NULL) return;
>+
>+ if (readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
>+ wait_time = 500; /* 0.5 seconds */
>+ writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
>+ writel(OHCI_OCR, base + OHCI_CMDSTATUS);
>+ while (wait_time > 0 &&
>+ readl(base + OHCI_CONTROL) &
>OHCI_CTRL_IR) {
>+ wait_time -= 10;
>+ msleep(10);
>+ }
>+ }
>+
>+ /*
>+ * disable interrupts
>+ */
>+ writel(~(u32)0, base + OHCI_INTRDISABLE);
>+ writel(~(u32)0, base + OHCI_INTRSTATUS);
>+
>+ iounmap(base);
>+}
>+
>+static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
>+{
>+ int wait_time, delta;
>+ void __iomem *base, *op_reg_base;
>+ u32 hcc_params, val, temp;
>+ u8 cap_length;
>+
>+ base = ioremap_nocache(pci_resource_start(pdev, 0),
>+ pci_resource_len(pdev, 0));
>+ if (base == NULL) return;
>+
>+ cap_length = readb(base);
>+ op_reg_base = base + cap_length;
>+ hcc_params = readl(base + EHCI_HCC_PARAMS);
>+ hcc_params = (hcc_params >> 8) & 0xff;
>+ if (hcc_params) {
>+ pci_read_config_dword(pdev,
>+ hcc_params + EHCI_USBLEGSUP,
>+ &val);
>+ if (((val & 0xff) == 1) && (val &
>EHCI_USBLEGSUP_BIOS)) {
>+ /*
>+ * Ok, BIOS is in smm mode, try to hand off...
>+ */
>+ pci_read_config_dword(pdev,
>+ hcc_params +
>EHCI_USBLEGCTLSTS,
>+ &temp);
>+ pci_write_config_dword(pdev,
>+ hcc_params +
>EHCI_USBLEGCTLSTS,
>+ temp |
>EHCI_USBLEGCTLSTS_SOOE);
>+ val |= EHCI_USBLEGSUP_OS;
>+ pci_write_config_dword(pdev,
>+ hcc_params +
>EHCI_USBLEGSUP,
>+ val);
>+
>+ wait_time = 500;
>+ do {
>+ msleep(10);
>+ wait_time -= 10;
>+ pci_read_config_dword(pdev,
>+ hcc_params +
>EHCI_USBLEGSUP,
>+ &val);
>+ } while (wait_time && (val &
>EHCI_USBLEGSUP_BIOS));
>+ if (!wait_time) {
>+ /*
>+ * well, possibly buggy BIOS...
>+ */
>+ printk(KERN_WARNING "EHCI early
>BIOS handoff "
>+ "failed (BIOS
>bug ?)\n");
>+ pci_write_config_dword(pdev,
>+ hcc_params +
>EHCI_USBLEGSUP,
>+ EHCI_USBLEGSUP_OS);
>+ pci_write_config_dword(pdev,
>+ hcc_params +
>EHCI_USBLEGCTLSTS,
>+ 0);
>+ }
>+ }
>+ }
>+
>+ /*
>+ * halt EHCI & disable its interrupts in any case
>+ */
>+ val = readl(op_reg_base + EHCI_USBSTS);
>+ if ((val & EHCI_USBSTS_HALTED) == 0) {
>+ val = readl(op_reg_base + EHCI_USBCMD);
>+ val &= ~EHCI_USBCMD_RUN;
>+ writel(val, op_reg_base + EHCI_USBCMD);
>+
>+ wait_time = 2000;
>+ delta = 100;
>+ do {
>+ writel(0x3f, op_reg_base + EHCI_USBSTS);
>+ udelay(delta);
>+ wait_time -= delta;
>+ val = readl(op_reg_base + EHCI_USBSTS);
>+ if ((val == ~(u32)0) || (val &
>EHCI_USBSTS_HALTED)) {
>+ break;
>+ }
>+ } while (wait_time > 0);
>+ }
>+ writel(0, op_reg_base + EHCI_USBINTR);
>+ writel(0x3f, op_reg_base + EHCI_USBSTS);
>+
>+ iounmap(base);
>+
>+ return;
>+}
>+
>+
>+
>+static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
>+{
>+ if (!usb_early_handoff)
>+ return;
>+
>+ if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) |
>0x00)) { /* UHCI */
>+ quirk_usb_handoff_uhci(pdev);
>+ } else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8)
>| 0x10)) { /* OHCI */
>+ quirk_usb_handoff_ohci(pdev);
>+ } else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8)
>| 0x20)) { /* EHCI */
>+ quirk_usb_disable_ehci(pdev);
>+ }
>+
>+ return;
>+}
>+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID,
>quirk_usb_early_handoff);
>--- g26.orig/drivers/pci/quirks.c 2005-07-12
>05:38:23.000000000 -0700
>+++ g26/drivers/pci/quirks.c 2005-07-31 17:26:11.000000000 -0700
>@@ -7,6 +7,9 @@
> *
> * Copyright (c) 1999 Martin Mares <[email protected]>
> *
>+ * Quirks for USB host controllers should be handled in the USB
>+ * quirks file; that code is reused by host controller drivers.
>+ *
> * The bridge optimization stuff has been removed. If you really
> * have a silly BIOS which is unable to set your host bridge right,
> * use the PowerTweak utility (see
>http://powertweak.sourceforge.net).
>@@ -513,28 +516,6 @@ static void quirk_via_irq(struct pci_dev
> DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID,
>quirk_via_irq);
>
> /*
>- * PIIX3 USB: We have to disable USB interrupts that are
>- * hardwired to PIRQD# and may be shared with an
>- * external device.
>- *
>- * Legacy Support Register (LEGSUP):
>- * bit13: USB PIRQ Enable (USBPIRQDEN),
>- * bit4: Trap/SMI On IRQ Enable (USBSMIEN).
>- *
>- * We mask out all r/wc bits, too.
>- */
>-static void __devinit quirk_piix3_usb(struct pci_dev *dev)
>-{
>- u16 legsup;
>-
>- pci_read_config_word(dev, 0xc0, &legsup);
>- legsup &= 0x50ef;
>- pci_write_config_word(dev, 0xc0, legsup);
>-}
>-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,
>PCI_DEVICE_ID_INTEL_82371SB_2, quirk_piix3_usb );
>-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,
>PCI_DEVICE_ID_INTEL_82371AB_2, quirk_piix3_usb );
>-
>-/*
> * VIA VT82C598 has its device ID settable and many BIOSes
> * set it to the ID of VT82C597 for backward compatibility.
> * We need to switch it off to be able to recognize the real
>@@ -871,234 +852,6 @@ static void __init quirk_sis_96x_smbus(s
> pci_read_config_byte(dev, 0x77, &val);
> }
>
>-
>-#define UHCI_USBLEGSUP 0xc0 /*
>legacy support */
>-#define UHCI_USBCMD 0 /* command register */
>-#define UHCI_USBSTS 2 /* status register */
>-#define UHCI_USBINTR 4 /* interrupt register */
>-#define UHCI_USBLEGSUP_DEFAULT 0x2000 /* only
>PIRQ enable set */
>-#define UHCI_USBCMD_RUN (1 << 0) /*
>RUN/STOP bit */
>-#define UHCI_USBCMD_GRESET (1 << 2) /* Global reset */
>-#define UHCI_USBCMD_CONFIGURE (1 << 6) /* config semaphore */
>-#define UHCI_USBSTS_HALTED (1 << 5) /* HCHalted bit */
>-
>-#define OHCI_CONTROL 0x04
>-#define OHCI_CMDSTATUS 0x08
>-#define OHCI_INTRSTATUS 0x0c
>-#define OHCI_INTRENABLE 0x10
>-#define OHCI_INTRDISABLE 0x14
>-#define OHCI_OCR (1 << 3) /* ownership
>change request */
>-#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */
>-#define OHCI_INTR_OC (1 << 30) /* ownership change */
>-
>-#define EHCI_HCC_PARAMS 0x08 /*
>extended capabilities */
>-#define EHCI_USBCMD 0 /* command register */
>-#define EHCI_USBCMD_RUN (1 << 0) /*
>RUN/STOP bit */
>-#define EHCI_USBSTS 4 /* status register */
>-#define EHCI_USBSTS_HALTED (1 << 12) /* HCHalted bit */
>-#define EHCI_USBINTR 8 /* interrupt register */
>-#define EHCI_USBLEGSUP 0 /*
>legacy support register */
>-#define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */
>-#define EHCI_USBLEGSUP_OS (1 << 24) /* OS semaphore */
>-#define EHCI_USBLEGCTLSTS 4 /* legacy
>control/status */
>-#define EHCI_USBLEGCTLSTS_SOOE (1 << 13) /* SMI
>on ownership change */
>-
>-int usb_early_handoff __devinitdata = 0;
>-static int __init usb_handoff_early(char *str)
>-{
>- usb_early_handoff = 1;
>- return 0;
>-}
>-__setup("usb-handoff", usb_handoff_early);
>-
>-static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
>-{
>- unsigned long base = 0;
>- int wait_time, delta;
>- u16 val, sts;
>- int i;
>-
>- for (i = 0; i < PCI_ROM_RESOURCE; i++)
>- if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
>- base = pci_resource_start(pdev, i);
>- break;
>- }
>-
>- if (!base)
>- return;
>-
>- /*
>- * stop controller
>- */
>- sts = inw(base + UHCI_USBSTS);
>- val = inw(base + UHCI_USBCMD);
>- val &= ~(u16)(UHCI_USBCMD_RUN | UHCI_USBCMD_CONFIGURE);
>- outw(val, base + UHCI_USBCMD);
>-
>- /*
>- * wait while it stops if it was running
>- */
>- if ((sts & UHCI_USBSTS_HALTED) == 0)
>- {
>- wait_time = 1000;
>- delta = 100;
>-
>- do {
>- outw(0x1f, base + UHCI_USBSTS);
>- udelay(delta);
>- wait_time -= delta;
>- val = inw(base + UHCI_USBSTS);
>- if (val & UHCI_USBSTS_HALTED)
>- break;
>- } while (wait_time > 0);
>- }
>-
>- /*
>- * disable interrupts & legacy support
>- */
>- outw(0, base + UHCI_USBINTR);
>- outw(0x1f, base + UHCI_USBSTS);
>- pci_read_config_word(pdev, UHCI_USBLEGSUP, &val);
>- if (val & 0xbf)
>- pci_write_config_word(pdev, UHCI_USBLEGSUP,
>UHCI_USBLEGSUP_DEFAULT);
>-
>-}
>-
>-static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
>-{
>- void __iomem *base;
>- int wait_time;
>-
>- base = ioremap_nocache(pci_resource_start(pdev, 0),
>- pci_resource_len(pdev, 0));
>- if (base == NULL) return;
>-
>- if (readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
>- wait_time = 500; /* 0.5 seconds */
>- writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
>- writel(OHCI_OCR, base + OHCI_CMDSTATUS);
>- while (wait_time > 0 &&
>- readl(base + OHCI_CONTROL) &
>OHCI_CTRL_IR) {
>- wait_time -= 10;
>- msleep(10);
>- }
>- }
>-
>- /*
>- * disable interrupts
>- */
>- writel(~(u32)0, base + OHCI_INTRDISABLE);
>- writel(~(u32)0, base + OHCI_INTRSTATUS);
>-
>- iounmap(base);
>-}
>-
>-static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
>-{
>- int wait_time, delta;
>- void __iomem *base, *op_reg_base;
>- u32 hcc_params, val, temp;
>- u8 cap_length;
>-
>- base = ioremap_nocache(pci_resource_start(pdev, 0),
>- pci_resource_len(pdev, 0));
>- if (base == NULL) return;
>-
>- cap_length = readb(base);
>- op_reg_base = base + cap_length;
>- hcc_params = readl(base + EHCI_HCC_PARAMS);
>- hcc_params = (hcc_params >> 8) & 0xff;
>- if (hcc_params) {
>- pci_read_config_dword(pdev,
>- hcc_params + EHCI_USBLEGSUP,
>- &val);
>- if (((val & 0xff) == 1) && (val &
>EHCI_USBLEGSUP_BIOS)) {
>- /*
>- * Ok, BIOS is in smm mode, try to hand off...
>- */
>- pci_read_config_dword(pdev,
>- hcc_params +
>EHCI_USBLEGCTLSTS,
>- &temp);
>- pci_write_config_dword(pdev,
>- hcc_params +
>EHCI_USBLEGCTLSTS,
>- temp |
>EHCI_USBLEGCTLSTS_SOOE);
>- val |= EHCI_USBLEGSUP_OS;
>- pci_write_config_dword(pdev,
>- hcc_params +
>EHCI_USBLEGSUP,
>- val);
>-
>- wait_time = 500;
>- do {
>- msleep(10);
>- wait_time -= 10;
>- pci_read_config_dword(pdev,
>- hcc_params +
>EHCI_USBLEGSUP,
>- &val);
>- } while (wait_time && (val &
>EHCI_USBLEGSUP_BIOS));
>- if (!wait_time) {
>- /*
>- * well, possibly buggy BIOS...
>- */
>- printk(KERN_WARNING "EHCI early
>BIOS handoff "
>- "failed (BIOS
>bug ?)\n");
>- pci_write_config_dword(pdev,
>- hcc_params +
>EHCI_USBLEGSUP,
>- EHCI_USBLEGSUP_OS);
>- pci_write_config_dword(pdev,
>- hcc_params +
>EHCI_USBLEGCTLSTS,
>- 0);
>- }
>- }
>- }
>-
>- /*
>- * halt EHCI & disable its interrupts in any case
>- */
>- val = readl(op_reg_base + EHCI_USBSTS);
>- if ((val & EHCI_USBSTS_HALTED) == 0) {
>- val = readl(op_reg_base + EHCI_USBCMD);
>- val &= ~EHCI_USBCMD_RUN;
>- writel(val, op_reg_base + EHCI_USBCMD);
>-
>- wait_time = 2000;
>- delta = 100;
>- do {
>- writel(0x3f, op_reg_base + EHCI_USBSTS);
>- udelay(delta);
>- wait_time -= delta;
>- val = readl(op_reg_base + EHCI_USBSTS);
>- if ((val == ~(u32)0) || (val &
>EHCI_USBSTS_HALTED)) {
>- break;
>- }
>- } while (wait_time > 0);
>- }
>- writel(0, op_reg_base + EHCI_USBINTR);
>- writel(0x3f, op_reg_base + EHCI_USBSTS);
>-
>- iounmap(base);
>-
>- return;
>-}
>-
>-
>-
>-static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
>-{
>- if (!usb_early_handoff)
>- return;
>-
>- if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) |
>0x00)) { /* UHCI */
>- quirk_usb_handoff_uhci(pdev);
>- } else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8)
>| 0x10)) { /* OHCI */
>- quirk_usb_handoff_ohci(pdev);
>- } else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8)
>| 0x20)) { /* EHCI */
>- quirk_usb_disable_ehci(pdev);
>- }
>-
>- return;
>-}
>-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID,
>quirk_usb_early_handoff);
>-
> /*
> * ... This is further complicated by the fact that some SiS96x south
> * bridges pretend to be 85C503/5513 instead. In that case see if we
>-
>To unsubscribe from this list: send the line "unsubscribe
>linux-kernel" in
>the body of a message to [email protected]
>More majordomo info at http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at http://www.tux.org/lkml/
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
| |
 |