Hi there, I've got to setup D-Link DSL200i Kernel: 2.6.11.12 Slackware 10.1.0 Aditional software user: eagle-usb.org or atm.eagle-usb.org Problem: on my own computer, everything works fine (USB HUB 2.0, Intel chipset, UHCI) On this one - only when on high load I tried to play with delays in various functions of uhci_hcd.c - sometimes it helps If I change uhci_result_control ending: td= list_entry(tmp,......) to td=list_entry(head->next,..........) - setup passes USB device: 0x1110:0x9010 -> without firmware, 0x1110:0x900f -> with firmware eagle usb module uploads firmware and initiates a reset. This is where I get to the TD selection problem. More details on dlink.log
hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002 uhci_hcd 0000:00:14.2: port 1 portsc 0883,00 hub 1-0:1.0: over-current change on port 1 hub 1-0:1.0: port 1, status 0101, change 0009, 12 Mb/s uhci_hcd 0000:00:14.2: wakeup_hc hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 usb 1-1: new full speed USB device using uhci_hcd and address 5 uhci_hcd 0000:00:14.2: uhci_result_control: failed with status 440000 [c5102240] link (051021b2) element (04548040) 0: [c4548040] link (04548080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=07d0cce0) 1: [c4548080] link (045480c0) e3 SPD Active Length=0 MaxLen=3f DT1 EndPt=0 Dev=0, PID=69(IN) (buf=071c83e0) 2: [c45480c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000) usb 1-1: device descriptor read/64, error -71 usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0 DEV: registering device: ID = '1-1' usb 1-1: hotplug PM: Adding info for usb:1-1 bus usb: add device 1-1 bound device '1-1' to driver 'usb' usb 1-1: adding 1-1:1.0 (config #1, interface 0) DEV: registering device: ID = '1-1:1.0' usb 1-1:1.0: hotplug PM: Adding info for usb:1-1:1.0 bus usb: add device 1-1:1.0 ueagle-atm 1-1:1.0: usb_probe_interface ueagle-atm 1-1:1.0: usb_probe_interface - got id usb 1-1: [ueagle-atm] ADSL device founded vid (0X1110) pid (0X9010) usb 1-1: reset full speed USB device using uhci_hcd and address 5 usb 1-1: [ueagle-atm] pre-firmware device, uploading firmware CLASS: registering class device: ID = '1-1' class_hotplug - name = 1-1 class_hotplug - hotplug() returned -19 class_hotplug - name = 1-1 CLASS: Unregistering class device. ID = '1-1' class_hotplug - name = 1-1 device class '1-1': release. usb 1-1: [ueagle-atm] firmware uploaded bound device '1-1:1.0' to driver 'ueagle-atm' hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002 hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002 uhci_hcd 0000:00:14.2: port 1 portsc 008a,00 hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s usb 1-1: USB disconnect, address 5 usb 1-1: usb_disable_device nuking all URBs usb 1-1: unregistering interface 1-1:1.0 bus usb: remove device 1-1:1.0 PM: Removing info for usb:1-1:1.0 usb 1-1:1.0: hotplug usb 1-1: unregistering device DEV: Unregistering device. ID = '1-1' bus usb: remove device 1-1 PM: Removing info for usb:1-1 usb 1-1: hotplug hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002 uhci_hcd 0000:00:14.2: port 1 portsc 0093,00 hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 usb 1-1: new full speed USB device using uhci_hcd and address 6 usb 1-1: skipped 2 descriptors after interface usb 1-1: new device strings: Mfr=0, Product=2, SerialNumber=3 usb 1-1: default language 0x0409 usb 1-1: Product: ADSL-USB Modem usb 1-1: SerialNumber: 000D88E54893 DEV: registering device: ID = '1-1' usb 1-1: hotplug PM: Adding info for usb:1-1 bus usb: add device 1-1 bound device '1-1' to driver 'usb' uhci_hcd 0000:00:14.2: uhci_result_control: failed with status 440000 [c5102240] link (051021e2) element (04548080) Element != First TD 0: [c4548040] link (04548080) e3 Length=7 MaxLen=7 DT0 EndPt=0 Dev=6, PID=2d(SETUP) (buf=07752620) 1: [c4548080] link (00000001) e0 IOC Stalled CRC/Timeo Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=6, PID=69(IN) (buf=00000000) usb 1-1: can't set config #1, error -84 bus usb: remove device 1-1 PM: Removing info for usb:1-1 usb 1-1: hotplug uhci_hcd 0000:00:14.2: port 1 portsc 0895,00 usb 1-1: new full speed USB device using uhci_hcd and address 7 uhci_hcd 0000:00:14.2: port 1 portsc 0895,00 usb 1-1: skipped 2 descriptors after interface usb 1-1: new device strings: Mfr=0, Product=2, SerialNumber=3 usb 1-1: default language 0x0409 usb 1-1: Product: ADSL-USB Modem usb 1-1: SerialNumber: 000D88E54893 DEV: registering device: ID = '1-1' usb 1-1: hotplug PM: Adding info for usb:1-1 bus usb: add device 1-1 bound device '1-1' to driver 'usb' uhci_hcd 0000:00:14.2: uhci_result_control: failed with status 440000 [c5102240] link (051021e2) element (04548080) Element != First TD 0: [c4548040] link (04548080) e3 Length=7 MaxLen=7 DT0 EndPt=0 Dev=7, PID=2d(SETUP) (buf=07752720) 1: [c4548080] link (00000001) e0 IOC Stalled CRC/Timeo Length=7ff MaxLen=7ff DT1 EndPt=0 Dev=7, PID=69(IN) (buf=00000000) usb 1-1: can't set config #1, error -84 bus usb: remove device 1-1 PM: Removing info for usb:1-1 usb 1-1: hotplug hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0002 uhci_hcd 0000:00:14.2: port 1 portsc 0899,00 hub 1-0:1.0: port 1 enable change, status 00000101 hub 1-0:1.0: over-current change on port 1 If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes. Linux mindaugas 2.6.11.12 #19 Tue Jul 26 09:23:15 EEST 2005 i686 unknown unknown GNU/Linux Gnu C 3.3.6 Gnu make 3.80 binutils 2.15.92.0.2 util-linux 2.12p mount 2.12p module-init-tools 3.1 e2fsprogs 1.35 reiserfsprogs line reiser4progs line PPP 2.4.2 Linux C Library 2.3.5 Dynamic linker (ldd) 2.3.5 Linux C++ Library 5.0.7 Procps 3.2.3 Net-tools 1.60 Kbd 1.12 Sh-utils 5.2.1 udev 058 Modules Loaded ueagle usbatm uhci_hcd ohci_hcd ehci_hcd usbcore firmware_class atm snd_pcm_oss snd_mixer_oss snd_es18xx snd_pcm snd_page_alloc snd_opl3_lib snd_timer snd_hwdep snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore intel_agp agpgart 00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR+ <PERR- Latency: 64 Region 0: Memory at 44000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 1.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> 00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00001000-00001fff Memory behind bridge: 40000000-400fffff Prefetchable memory behind bridge: 41000000-41ffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+ 00:0a.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 05) Subsystem: Compaq Computer Corporation NC3161 Fast Ethernet NIC (embedded, WOL) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 42100000 (32-bit, prefetchable) [size=4K] Region 1: I/O ports at 2000 [size=32] Region 2: Memory at 42000000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:14.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:14.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at 2040 [size=16] 00:14.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin D routed to IRQ 11 Region 4: I/O ports at 2020 [size=32] 00:14.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 9 01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c) (prog-if 00 [VGA]) Subsystem: ATI Technologies Inc Rage Pro Turbo AGP 2X Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 41000000 (32-bit, prefetchable) [size=16M] Region 1: I/O ports at 1000 [size=256] Region 2: Memory at 40000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [50] AGP version 1.0 Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
begin:vcard fn;quoted-printable:Giedrius Liubavi=C4=8Dius n;quoted-printable:Liubavi=C4=8Dius;Giedrius org:;Technologijos fak. adr;quoted-printable:;;;=C5=A0iauliai;;;Lietuva email;internet:[email protected] title:Studentas, R3 tel;work:+37041595737 tel;cell:+37068450498 x-mozilla-html:TRUE url:http://galva.su.lt version:2.1 end:vcard
Attachment:
signature.asc
Description: OpenPGP digital signature
- Prev by Date: [patch 0/6] remove PageReserved
- Next by Date: [patch 1/6] mm: comment rmap
- Previous by thread: [patch 0/6] remove PageReserved
- Next by thread: [patch] mpol_free_shared_poliy() is not called for non-inline symlink under tmpfs
- Index(es):
