Re: tx queue start entry x dirty entry y (was 8139too PCI IRQ issues)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





[I'm currently having nasty ISP problems, so I've removed myself from the list for the time-being, as e-mail is struggling to get through to me -- hence the delay in my reply to this, SORRY]


Probably it's the miss config of PIC. Can you post more info?

Thanks for helping! :-)))


  - /proc/interrupt

more /proc/interrupts
           CPU0
  0:     473349    IO-APIC-edge  timer
  1:         10    IO-APIC-edge  i8042
  2:          0          XT-PIC  cascade
  5:          1    IO-APIC-edge  soundblaster
  7:          2    IO-APIC-edge  parport0
  9:       8152    IO-APIC-edge  aic7xxx
 10:      19988    IO-APIC-edge  eth0
11: 577 IO-APIC-edge ohci_hcd, ohci_hcd, ohci_hcd, ohci_hcd, eth1
 12:        101    IO-APIC-edge  i8042
 14:      51421    IO-APIC-edge  ide0
NMI:          0
LOC:     473350
ERR:          0
MIS:          0

  - mptable

I'm running a single (old) processor, and I dont have mptable installed.... I can't even find a package for it, am I missing something? Sorry!

  - 8259A.pl

perl 8259A.pl
irq 0: 00, edge
irq 1: 00, edge
irq 2: 00, edge
irq 3: 00, edge
irq 4: 00, edge
irq 5: 00, edge
irq 6: 00, edge
irq 7: 00, edge
irq 8: 0a, edge
irq 9: 0a, level
irq 10: 0a, edge
irq 11: 0a, level
irq 12: 0a, edge
irq 13: 0a, edge
irq 14: 0a, edge
irq 15: 0a, edge


  - lspci -vvv

0000:00:00.0 Non-VGA unclassified device: Intel Corp. 82378ZB/IB, 82379AB (SIO, SIO.A) PCI to ISA Bridge (rev 88) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

0000:00:01.0 IDE interface: Silicon Image, Inc. (formerly CMD Technology Inc) PCI0646 (rev 01) (prog-if 8a [Master SecP PriP]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (500ns min, 1000ns max)
        Interrupt: pin A routed to IRQ 14
        Region 0: I/O ports at <ignored>
        Region 1: I/O ports at <ignored>
        Region 2: I/O ports at <ignored>
        Region 3: I/O ports at <ignored>
        Region 4: I/O ports at fc00 [size=16]

0000:00:02.0 SCSI storage controller: Adaptec AIC-7880U
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 248 (2000ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
        Interrupt: pin A routed to IRQ 9
        Region 0: I/O ports at f800 [disabled] [size=256]
Region 1: Memory at ffbfc000 (32-bit, non-prefetchable) [size=4K]

0000:00:0b.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2064W [Millennium] (rev 01) (prog-if 00 [VGA]) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 11
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=16K]
        Region 1: Memory at a0800000 (32-bit, prefetchable) [size=8M]
        Expansion ROM at d0000000 [disabled] [size=64K]

0000:00:0d.0 USB Controller: Lucent Microelectronics USS-344S USB Controller (rev 11) (prog-if 10 [OHCI])
        Subsystem: Lucent Microelectronics USS-344S USB Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (750ns min, 21500ns max)
        Interrupt: pin A routed to IRQ 11
Region 0: Memory at ffbec000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-

0000:00:0d.1 USB Controller: Lucent Microelectronics USS-344S USB Controller (rev 11) (prog-if 10 [OHCI])
        Subsystem: Lucent Microelectronics USS-344S USB Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (750ns min, 21500ns max)
        Interrupt: pin A routed to IRQ 11
Region 0: Memory at ffbdc000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-

0000:00:0d.2 USB Controller: Lucent Microelectronics USS-344S USB Controller (rev 11) (prog-if 10 [OHCI])
        Subsystem: Lucent Microelectronics USS-344S USB Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (750ns min, 21500ns max)
        Interrupt: pin A routed to IRQ 11
Region 0: Memory at ffbcc000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-

0000:00:0d.3 USB Controller: Lucent Microelectronics USS-344S USB Controller (rev 11) (prog-if 10 [OHCI])
        Subsystem: Lucent Microelectronics USS-344S USB Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (750ns min, 21500ns max)
        Interrupt: pin A routed to IRQ 11
Region 0: Memory at ffbbc000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-

0000:00:0e.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at f400 [size=256]
Region 1: Memory at ffbac000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:14.0 RAM memory: Intel Corp. 450KX/GX [Orion] - 82453KX/GX Memory controller (rev 04) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

0000:00:19.0 Host bridge: Intel Corp. 450KX/GX [Orion] - 82454KX/GX PCI bridge (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 32, Cache Line Size: 0x08 (32 bytes)


--

On 23 Jul 2005, at 21:11, OGAWA Hirofumi wrote:

Mark Burton <[email protected]> writes:

Hi,
I'm getting similar results to Nick Warne, in that when my ethernet is
stressed at all (for instance by NFS), I end up with
nfs: server..... not responding, still trying
nfs: server .... OK

With a realtec card, I get errors in /var/spool/messages along the
lines of:
Jul  3 14:31:13 localhost kernel: eth1: Transmit timeout, status 0c
0005 c07f media 00.
Jul  3 14:31:13 localhost kernel: eth1: Tx queue start entry 1160
dirty entry 1156.
Jul  3 14:31:13 localhost kernel: eth1:  Tx descriptor 0 is
0008a03c. (queue head)
OGAWA Hirofumi <[email protected]>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]
  Powered by Linux