Re: VIA KT400 + Kernel 2.6.12 + IO-APIC + uhci_hcd = IRQ trouble

[Mathieu Bérard <Mathieu.Berard@crans.org>]

Michel Bouissou a écrit :

> Hi there,
>
> Natalie Protasevich and Alan Stern have worked a lot on helping me out with a 
> VIA KT400 chipset / kernel 2.6.12 / IO-APIC / IRQ problem "irq 21: nobody 
> cared!", which so far hasn't found its solution.
>
> Research done with Alan shows that, on my system, the USB 2.0 controller seems 
> to generate interrupts on the IRQ line attributed to the USB 1.1 controller, 
> which isn't supposed to happen, and puzzles the system, when IO-APIC is 
> enabled.
>
> However, this didn't cause problems with 2.4 series kernels.
>
> For the time being, there is no solution (Natalie is still investigating 
> this), and it boils down to the following:
>
> - If I boot with USB 2.0 enabled in BIOS, AND IO-APIC enabled in the kernel, 
> then it badly breaks.
>
> - If I either disable USB 2.0 in BIOS, or IO-APIC in the kernel, then it's OK.
>
> I found today the thread between Bjorn Helgaas and Mathieu Bérard on LKML, 
> where Mathieu reported the same problem, and Bjorn advised him to reverse a 
> kernel patch (http://lkml.org/lkml/2005/6/21/243 ).
>
> Mathieu (I don't have his email address, Bjorn, could you be so kind to 
> forward this message to him) reports that it apparently solved this problem, 
> so I tried to do the same, and reversed the same patch.
Hi,
yes I've encountered the same problem but my system
is a little bit different: It's a MSI mainboard with a VIA KT266A chipset
and no USB 2.0 controller (just 3 uhci).
IO-APIC is enabled.

With a 2.6.13-rc1-mm1 kernel, for example,
I got those error messages just after
the integrated sound card detection:

Jul  2 21:04:12 perenold kernel: irq 21: nobody cared (try booting with 
the "irqpoll" option)
Jul  2 21:04:12 perenold kernel: [<c0133c24>] __report_bad_irq+0x24/0x80
Jul  2 21:04:12 perenold kernel: [<c0133d22>] note_interrupt+0x72/0xc0
Jul  2 21:04:12 perenold kernel: [<c0133710>] __do_IRQ+0xe0/0xf0
Jul  2 21:04:12 perenold kernel: [<c0104f8e>] do_IRQ+0x3e/0x60
Jul  2 21:04:12 perenold kernel: =======================
Jul  2 21:04:12 perenold kernel: [<c0103502>] common_interrupt+0x1a/0x20
Jul  2 21:04:12 perenold kernel: [<c0142102>] zap_pte_range+0x82/0x1c0
Jul  2 21:04:12 perenold kernel: [<c01422bf>] unmap_page_range+0x7f/0xb0
Jul  2 21:04:12 perenold kernel: [<c01423f6>] unmap_vmas+0x106/0x210
Jul  2 21:04:12 perenold kernel: [<c01469c1>] exit_mmap+0x71/0x140
Jul  2 21:04:12 perenold kernel: [<c011547e>] mmput+0x2e/0xe0
Jul  2 21:04:12 perenold kernel: [<c015af3c>] exec_mmap+0xac/0x160
Jul  2 21:04:12 perenold kernel: [<c015b0a0>] flush_old_exec+0x70/0x700
Jul  2 21:04:12 perenold kernel: [<c0151475>] vfs_read+0xf5/0x160
Jul  2 21:04:12 perenold kernel: [<c015ae70>] kernel_read+0x40/0x60
Jul  2 21:04:12 perenold kernel: [<c0178f32>] load_elf_binary+0x252/0xd20
Jul  2 21:04:12 perenold kernel: [<c0138bf7>] buffered_rmqueue+0xb7/0x210
Jul  2 21:04:12 perenold kernel: [<c0138eeb>] __alloc_pages+0xdb/0x400
Jul  2 21:04:12 perenold kernel: [<c0104f95>] do_IRQ+0x45/0x60
Jul  2 21:04:12 perenold kernel: [<c01c2c6e>] __copy_from_user_ll+0x3e/0x70
Jul  2 21:04:12 perenold kernel: [<c015b92f>] 
search_binary_handler+0x4f/0x1d0
Jul  2 21:04:12 perenold kernel: [<c015bbfe>] do_execve+0x14e/0x200
Jul  2 21:04:12 perenold kernel: [<c010181f>] sys_execve+0x2f/0x70
Jul  2 21:04:12 perenold kernel: [<c0102aeb>] sysenter_past_esp+0x54/0x75
Jul  2 21:04:12 perenold kernel: handlers:
Jul  2 21:04:12 perenold kernel: [<e0c59450>] 
(snd_via82xx_interrupt+0x0/0xc0 [snd_via82xx])
Jul  2 21:04:12 perenold kernel: Disabling IRQ #21

and later:

Jul  2 21:04:37 perenold kernel: uhci_hcd 0000:00:11.3: Unlink after 
no-IRQ?  Controller is probably using the wrong IRQ.

IRQ 21 is then crazy with a rate of increasing of around 200000 per 
second in /proc/interrupts

All those error messages disappear if I revert the patch as I was 
advised to.

I have that in /proc/interrupts: (with an healthy kernel)
          CPU0
 0:  201893429    IO-APIC-edge  timer
 1:         21    IO-APIC-edge  i8042
 7:          2    IO-APIC-edge  parport0
 8:          0    IO-APIC-edge  rtc
 9:          0   IO-APIC-level  acpi
14:    5448524    IO-APIC-edge  ide0
15:   14583934    IO-APIC-edge  ide1
16:     172543   IO-APIC-level  ide3
17:     299810   IO-APIC-level  saa7134[0]
18:   24973124   IO-APIC-level  eth0
19:    5233000   IO-APIC-level  eth1
20:         82   IO-APIC-level  uhci_hcd:usb1, uhci_hcd:usb2, uhci_hcd:usb3
21:          0   IO-APIC-level  VIA8233
NMI:          0
LOC:  201897508
ERR:          0
MIS:          0


So maybe, in my case, it's a mess between the IRQ of the uhci controllers
and the one of the integrated AC'97 sound ship.

But as it is mainly a server box nor the usb controllers nor the sound 
card are used very often,
so I don't know if those devices are actually working now. I am currently on
vacation 300 km away from that box so I can't really plug an USB key to
do some tests. But I will as soon as a can if that can help.
I will also try to reboot the box several times to see if the "IRQ 21 
nobody cared" error
reappears.

--
Mathieu









-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/