[patch 2.6] remove PCI_BRIDGE_CTL_VGA handling from setup-bus.c

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The setup-bus code doesn't work correctly for configurations
with more than one display adapter in the same PCI domain.
This stuff actually is a leftover of an early 2.4 PCI setup code
and apparently it stopped working after some "bridge_ctl" changes.
So the best thing we can do is just to remove it and rely on the fact
that any firmware *has* to configure VGA port forwarding for the boot
display device properly.

But then we need to ensure that the bus->bridge_ctl will always
contain valid information collected at the probe time, therefore
the following change in pci_scan_bridge() is needed.

Signed-off-by: Ivan Kokshaysky <[email protected]>

--- 2.6.13-rc3/drivers/pci/probe.c	Thu Jul 14 11:09:52 2005
+++ linux/drivers/pci/probe.c	Thu Jul 14 11:22:06 2005
@@ -507,7 +507,7 @@ int __devinit pci_scan_bridge(struct pci
 		pci_write_config_dword(dev, PCI_PRIMARY_BUS, buses);
 
 		if (!is_cardbus) {
-			child->bridge_ctl = PCI_BRIDGE_CTL_NO_ISA;
+			child->bridge_ctl = bctl | PCI_BRIDGE_CTL_NO_ISA;
 			/*
 			 * Adjust subordinate busnr in parent buses.
 			 * We do this before scanning for children because
--- 2.6.13-rc3/drivers/pci/setup-bus.c	Thu Jul 14 11:09:52 2005
+++ linux/drivers/pci/setup-bus.c	Thu Jul 14 11:22:54 2005
@@ -51,8 +51,6 @@ pbus_assign_resources_sorted(struct pci_
 	struct resource_list head, *list, *tmp;
 	int idx;
 
-	bus->bridge_ctl &= ~PCI_BRIDGE_CTL_VGA;
-
 	head.next = NULL;
 	list_for_each_entry(dev, &bus->devices, bus_list) {
 		u16 class = dev->class >> 8;
@@ -62,10 +60,6 @@ pbus_assign_resources_sorted(struct pci_
 		    class == PCI_CLASS_BRIDGE_HOST)
 			continue;
 
-		if (class == PCI_CLASS_DISPLAY_VGA ||
-		    class == PCI_CLASS_NOT_DEFINED_VGA)
-			bus->bridge_ctl |= PCI_BRIDGE_CTL_VGA;
-
 		pdev_sort_resources(dev, &head);
 	}
 
@@ -509,12 +503,6 @@ pci_bus_assign_resources(struct pci_bus 
 
 	pbus_assign_resources_sorted(bus);
 
-	if (bus->bridge_ctl & PCI_BRIDGE_CTL_VGA) {
-		/* Propagate presence of the VGA to upstream bridges */
-		for (b = bus; b->parent; b = b->parent) {
-			b->bridge_ctl |= PCI_BRIDGE_CTL_VGA;
-		}
-	}
 	list_for_each_entry(dev, &bus->devices, bus_list) {
 		b = dev->subordinate;
 		if (!b)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]
  Powered by Linux