aic7xxx regression occuring after 2.6.12 final

[Tony Vroon <chainsaw@gentoo.org>]

Hiya,

For my Adaptec 29160 card; I see a regression after 2.6.12 final.
To be exact, these releases work for me:
2.6.12
2.6.12.1

These releases do not work for me:
2.6.12-mm1
2.6.12-mm2
2.6.12-git7
2.6.13-rc1

On a working kernel; I see the following:
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level,
high) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec 29160 Ultra160 SCSI adapter>
        aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

  Vendor: FUJITSU   Model: MAP3367NP         Rev: 0106
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled.  Depth 253
 target0:0:0: Beginning Domain Validation
WIDTH IS 1
(scsi0:A:0): 6.600MB/s transfers (16bit)
(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
 target0:0:0: Ending Domain Validation

On a failing kernel, I see:
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level,
high) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec 29160 Ultra160 SCSI adapter>
        aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

target0:0:0: asynchronous
  Vendor: FUJITSU   Model: MAP3367NP         Rev: 0106
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled.  Depth 253
 target0:0:0: Beginning Domain Validation
 target0:0:0: wide asynchronous
(scsi0:A:0): refuses tagged commands. Performing non-tagged I/O
 target0:0:0: asynchronous
[The PC hangs at this point]


lspci output for the adapter:
0000:01:08.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
        Subsystem: Adaptec 29160 Ultra160 SCSI Controller
        Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 18
        BIST result: 00
        I/O ports at d800 [disabled] [size=256]
        Memory at db000000 (64-bit, non-prefetchable) [size=4K]
        Capabilities: [dc] Power Management version 2

Please let me know if there are specific patches I need to apply or
revert to debug this. I have more drives on this controller; to be exact
I have 2 U320-capable drives and one U160-capable drive on wide channel
A; and 3 removable media units (CD-R, DVD, CD-ROM) on the 50-pin
SCSI-bus.

Thanks,
Tony.
(Please CC replies to me as I am not subscribed to LKML or linux-scsi)

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/