Hi,
I've decided to get rid of the code duplication between parport_serial
and 8250_pci.
Essentially, we have two modules which support serial PCI devices.
As far as these serial PCI devices go, both modules contain similar
code, and actually share a little of the code between themselves.
So, the patch below takes 8250_pci, and exports a set of functions
to add/remove/suspend/resume PCI serial devices. parport_serial
uses these functions in conjunction with a table to register/remove
these devices, resulting in most of the serial-based code in
parport_serial becoming redundant. Additionally, we also get to
use the same quirk handling which are already in 8250_pci.
Also, as if that isn't enough, we add suspend/resume support for
the _serial_ side of parport&serial cards. I have not looked at
(and I don't know what's required for) the parport suspend/resume
support - it appears parport does not support suspend/resume.
This patch is only compile tested - I do not have any parport&serial
cards to test with.
Index: drivers/parport/parport_serial.c
===================================================================
--- 39040c7a05edd69381c0a25636a1a328d856cb9c/drivers/parport/parport_serial.c (mode:100644)
+++ uncommitted/drivers/parport/parport_serial.c (mode:100644)
@@ -23,13 +23,8 @@
#include <linux/pci.h>
#include <linux/parport.h>
#include <linux/parport_pc.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/list.h>
#include <linux/8250_pci.h>
-#include <asm/serial.h>
-
enum parport_pc_pci_cards {
titan_110l = 0,
titan_210l,
@@ -168,182 +163,147 @@
};
MODULE_DEVICE_TABLE(pci,parport_serial_pci_tbl);
-struct pci_board_no_ids {
- int flags;
- int num_ports;
- int base_baud;
- int uart_offset;
- int reg_shift;
- int (*init_fn)(struct pci_dev *dev, struct pci_board_no_ids *board,
- int enable);
- int first_uart_offset;
-};
-
-static int __devinit siig10x_init_fn(struct pci_dev *dev, struct pci_board_no_ids *board, int enable)
-{
- return pci_siig10x_fn(dev, enable);
-}
-
-static int __devinit siig20x_init_fn(struct pci_dev *dev, struct pci_board_no_ids *board, int enable)
-{
- return pci_siig20x_fn(dev, enable);
-}
-
-static int __devinit netmos_serial_init(struct pci_dev *dev, struct pci_board_no_ids *board, int enable)
-{
- board->num_ports = dev->subsystem_device & 0xf;
- return 0;
-}
-
-static struct pci_board_no_ids pci_boards[] __devinitdata = {
- /*
- * PCI Flags, Number of Ports, Base (Maximum) Baud Rate,
- * Offset to get to next UART's registers,
- * Register shift to use for memory-mapped I/O,
- * Initialization function, first UART offset
- */
-
-// Cards not tested are marked n/t
-// If you have one of these cards and it works for you, please tell me..
-
-/* titan_110l */ { SPCI_FL_BASE1 | SPCI_FL_BASE_TABLE, 1, 921600 },
-/* titan_210l */ { SPCI_FL_BASE1 | SPCI_FL_BASE_TABLE, 2, 921600 },
-/* netmos_9xx5_combo */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200, 0, 0, netmos_serial_init },
-/* netmos_9855 */ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 1, 115200, 0, 0, netmos_serial_init },
-/* avlab_1s1p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s1p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s1p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s2p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s2p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s2p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_2s1p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
-/* avlab_2s1p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
-/* avlab_2s1p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
-/* siig_1s1p_10x */ { SPCI_FL_BASE2, 1, 460800, 0, 0, siig10x_init_fn },
-/* siig_2s1p_10x */ { SPCI_FL_BASE2, 1, 921600, 0, 0, siig10x_init_fn },
-/* siig_2p1s_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
-/* siig_1s1p_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
-/* siig_2s1p_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
+/*
+ * This table describes the serial "geometry" of these boards. Any
+ * quirks for these can be found in drivers/serial/8250_pci.c
+ *
+ * Cards not tested are marked n/t
+ * If you have one of these cards and it works for you, please tell me..
+ */
+static struct pciserial_board pci_parport_serial_boards[] __devinitdata = {
+ [titan_110l] = {
+ .flags = FL_BASE1 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [titan_210l] = {
+ .flags = FL_BASE1 | FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [netmos_9xx5_combo] = {
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [netmos_9855] = {
+ .flags = FL_BASE2 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s1p] = { /* n/t */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s1p_650] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s1p_850] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s2p] = { /* n/t */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s2p_650] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s2p_850] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_2s1p] = { /* n/t */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_2s1p_650] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_2s1p_850] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [siig_1s1p_10x] = {
+ .flags = FL_BASE2,
+ .num_ports = 1,
+ .base_baud = 460800,
+ .uart_offset = 8,
+ },
+ [siig_2s1p_10x] = {
+ .flags = FL_BASE2,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [siig_2p1s_20x] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [siig_1s1p_20x] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [siig_2s1p_20x] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
};
struct parport_serial_private {
- int num_ser;
- int line[20];
- struct pci_board_no_ids ser;
+ struct serial_private *serial;
int num_par;
struct parport *port[PARPORT_MAX];
struct parport_pc_pci par;
};
-static int __devinit get_pci_port (struct pci_dev *dev,
- struct pci_board_no_ids *board,
- struct serial_struct *req,
- int idx)
-{
- unsigned long port;
- int base_idx;
- int max_port;
- int offset;
-
- base_idx = SPCI_FL_GET_BASE(board->flags);
- if (board->flags & SPCI_FL_BASE_TABLE)
- base_idx += idx;
-
- if (board->flags & SPCI_FL_REGION_SZ_CAP) {
- max_port = pci_resource_len(dev, base_idx) / 8;
- if (idx >= max_port)
- return 1;
- }
-
- offset = board->first_uart_offset;
-
- /* Timedia/SUNIX uses a mixture of BARs and offsets */
- /* Ugh, this is ugly as all hell --- TYT */
- if(dev->vendor == PCI_VENDOR_ID_TIMEDIA ) /* 0x1409 */
- switch(idx) {
- case 0: base_idx=0;
- break;
- case 1: base_idx=0; offset=8;
- break;
- case 2: base_idx=1;
- break;
- case 3: base_idx=1; offset=8;
- break;
- case 4: /* BAR 2*/
- case 5: /* BAR 3 */
- case 6: /* BAR 4*/
- case 7: base_idx=idx-2; /* BAR 5*/
- }
-
- port = pci_resource_start(dev, base_idx) + offset;
-
- if ((board->flags & SPCI_FL_BASE_TABLE) == 0)
- port += idx * (board->uart_offset ? board->uart_offset : 8);
-
- if (pci_resource_flags (dev, base_idx) & IORESOURCE_IO) {
- int high_bits_offset = ((sizeof(long)-sizeof(int))*8);
- req->port = port;
- if (high_bits_offset)
- req->port_high = port >> high_bits_offset;
- else
- req->port_high = 0;
- return 0;
- }
- req->io_type = SERIAL_IO_MEM;
- req->iomem_base = ioremap(port, board->uart_offset);
- req->iomem_reg_shift = board->reg_shift;
- req->port = 0;
- return req->iomem_base ? 0 : 1;
-}
-
/* Register the serial port(s) of a PCI card. */
static int __devinit serial_register (struct pci_dev *dev,
const struct pci_device_id *id)
{
- struct pci_board_no_ids *board;
struct parport_serial_private *priv = pci_get_drvdata (dev);
- struct serial_struct serial_req;
- int base_baud;
- int k;
- int success = 0;
-
- priv->ser = pci_boards[id->driver_data];
- board = &priv->ser;
- if (board->init_fn && ((board->init_fn) (dev, board, 1) != 0))
- return 1;
-
- base_baud = board->base_baud;
- if (!base_baud)
- base_baud = BASE_BAUD;
- memset (&serial_req, 0, sizeof (serial_req));
+ struct pciserial_board *board;
+ struct serial_private *serial;
- for (k = 0; k < board->num_ports; k++) {
- int line;
+ board = &pci_parport_serial_boards[id->driver_data];
+ serial = pciserial_init_ports(dev, board);
- if (priv->num_ser == ARRAY_SIZE (priv->line)) {
- printk (KERN_WARNING
- "parport_serial: %s: only %u serial lines "
- "supported (%d reported)\n", pci_name (dev),
- ARRAY_SIZE (priv->line), board->num_ports);
- break;
- }
-
- serial_req.irq = dev->irq;
- if (get_pci_port (dev, board, &serial_req, k))
- break;
- serial_req.flags = ASYNC_SKIP_TEST | ASYNC_AUTOPROBE;
- serial_req.baud_base = base_baud;
- line = register_serial (&serial_req);
- if (line < 0) {
- printk (KERN_DEBUG
- "parport_serial: register_serial failed\n");
- continue;
- }
- priv->line[priv->num_ser++] = line;
- success = 1;
- }
+ if (IS_ERR(serial))
+ return PTR_ERR(serial);
- return success ? 0 : 1;
+ priv->serial = serial;
+ return 0;
}
/* Register the parallel port(s) of a PCI card. */
@@ -411,7 +371,7 @@
priv = kmalloc (sizeof *priv, GFP_KERNEL);
if (!priv)
return -ENOMEM;
- priv->num_ser = priv->num_par = 0;
+ memset(priv, 0, sizeof(struct parport_serial_private));
pci_set_drvdata (dev, priv);
err = pci_enable_device (dev);
@@ -444,15 +404,12 @@
struct parport_serial_private *priv = pci_get_drvdata (dev);
int i;
+ pci_set_drvdata(dev, NULL);
+
// Serial ports
- for (i = 0; i < priv->num_ser; i++) {
- unregister_serial (priv->line[i]);
+ if (priv->serial)
+ pciserial_remove_ports(priv->serial);
- if (priv->ser.init_fn)
- (priv->ser.init_fn) (dev, &priv->ser, 0);
- }
- pci_set_drvdata (dev, NULL);
-
// Parallel ports
for (i = 0; i < priv->num_par; i++)
parport_pc_unregister_port (priv->port[i]);
@@ -461,11 +418,43 @@
return;
}
+static int parport_serial_pci_suspend(struct pci_dev *dev, pm_message_t state)
+{
+ struct parport_serial_private *priv = pci_get_drvdata(dev);
+
+ if (priv->serial)
+ pciserial_suspend_ports(priv->serial);
+
+ pci_save_state(dev);
+ pci_set_power_state(dev, pci_choose_state(dev, state));
+ return 0;
+}
+
+static int parport_serial_pci_resume(struct pci_dev *dev)
+{
+ struct parport_serial_private *priv = pci_get_drvdata(dev);
+
+ pci_set_power_state(dev, PCI_D0);
+ pci_restore_state(dev);
+
+ /*
+ * The device may have been disabled. Re-enable it.
+ */
+ pci_enable_device(dev);
+
+ if (priv->serial)
+ pciserial_resume_ports(priv->serial);
+
+ return 0;
+}
+
static struct pci_driver parport_serial_pci_driver = {
.name = "parport_serial",
.id_table = parport_serial_pci_tbl,
.probe = parport_serial_pci_probe,
.remove = __devexit_p(parport_serial_pci_remove),
+ .suspend = parport_serial_pci_suspend,
+ .resume = parport_serial_pci_resume,
};
Index: drivers/serial/8250_pci.c
===================================================================
--- 39040c7a05edd69381c0a25636a1a328d856cb9c/drivers/serial/8250_pci.c (mode:100644)
+++ uncommitted/drivers/serial/8250_pci.c (mode:100644)
@@ -34,36 +34,6 @@
#undef SERIAL_DEBUG_PCI
/*
- * Definitions for PCI support.
- */
-#define FL_BASE_MASK 0x0007
-#define FL_BASE0 0x0000
-#define FL_BASE1 0x0001
-#define FL_BASE2 0x0002
-#define FL_BASE3 0x0003
-#define FL_BASE4 0x0004
-#define FL_GET_BASE(x) (x & FL_BASE_MASK)
-
-/* Use successive BARs (PCI base address registers),
- else use offset into some specified BAR */
-#define FL_BASE_BARS 0x0008
-
-/* do not assign an irq */
-#define FL_NOIRQ 0x0080
-
-/* Use the Base address register size to cap number of ports */
-#define FL_REGION_SZ_CAP 0x0100
-
-struct pci_board {
- unsigned int flags;
- unsigned int num_ports;
- unsigned int base_baud;
- unsigned int uart_offset;
- unsigned int reg_shift;
- unsigned int first_offset;
-};
-
-/*
* init function returns:
* > 0 - number of ports
* = 0 - use board->num_ports
@@ -75,14 +45,13 @@
u32 subvendor;
u32 subdevice;
int (*init)(struct pci_dev *dev);
- int (*setup)(struct pci_dev *dev, struct pci_board *board,
- struct uart_port *port, int idx);
+ int (*setup)(struct serial_private *, struct pciserial_board *,
+ struct uart_port *, int idx);
void (*exit)(struct pci_dev *dev);
};
-#define PCI_NUM_BAR_RESOURCES 6
-
struct serial_private {
+ struct pci_dev *dev;
unsigned int nr;
void __iomem *remapped_bar[PCI_NUM_BAR_RESOURCES];
struct pci_serial_quirk *quirk;
@@ -101,17 +70,18 @@
}
static int
-setup_port(struct pci_dev *dev, struct uart_port *port,
+setup_port(struct serial_private *priv, struct uart_port *port,
int bar, int offset, int regshift)
{
- struct serial_private *priv = pci_get_drvdata(dev);
+ struct pci_dev *dev = priv->dev;
unsigned long base, len;
if (bar >= PCI_NUM_BAR_RESOURCES)
return -EINVAL;
+ base = pci_resource_start(dev, bar);
+
if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
- base = pci_resource_start(dev, bar);
len = pci_resource_len(dev, bar);
if (!priv->remapped_bar[bar])
@@ -120,13 +90,16 @@
return -ENOMEM;
port->iotype = UPIO_MEM;
+ port->iobase = 0;
port->mapbase = base + offset;
port->membase = priv->remapped_bar[bar] + offset;
port->regshift = regshift;
} else {
- base = pci_resource_start(dev, bar) + offset;
port->iotype = UPIO_PORT;
- port->iobase = base;
+ port->iobase = base + offset;
+ port->mapbase = 0;
+ port->membase = NULL;
+ port->regshift = 0;
}
return 0;
}
@@ -136,7 +109,7 @@
* Not that ugly ;) -- HW
*/
static int
-afavlab_setup(struct pci_dev *dev, struct pci_board *board,
+afavlab_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -149,7 +122,7 @@
offset += (idx - 4) * board->uart_offset;
}
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/*
@@ -189,13 +162,13 @@
* some serial ports are supposed to be hidden on certain models.
*/
static int
-pci_hp_diva_setup(struct pci_dev *dev, struct pci_board *board,
+pci_hp_diva_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int offset = board->first_offset;
unsigned int bar = FL_GET_BASE(board->flags);
- switch (dev->subsystem_device) {
+ switch (priv->dev->subsystem_device) {
case PCI_DEVICE_ID_HP_DIVA_MAESTRO:
if (idx == 3)
idx++;
@@ -212,7 +185,7 @@
offset += idx * board->uart_offset;
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/*
@@ -307,7 +280,7 @@
/* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
static int
-sbs_setup(struct pci_dev *dev, struct pci_board *board,
+sbs_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -323,7 +296,7 @@
} else /* we have only 8 ports on PMC-OCTALPRO */
return 1;
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/*
@@ -389,6 +362,9 @@
* - 10x cards have control registers in IO and/or memory space;
* - 20x cards have control registers in standard PCI configuration space.
*
+ * Note: all 10x cards have PCI device ids 0x10..
+ * all 20x cards have PCI device ids 0x20..
+ *
* Note: some SIIG cards are probed by the parport_serial object.
*/
@@ -442,24 +418,18 @@
return 0;
}
-int pci_siig10x_fn(struct pci_dev *dev, int enable)
+static int pci_siig_init(struct pci_dev *dev)
{
- int ret = 0;
- if (enable)
- ret = pci_siig10x_init(dev);
- return ret;
-}
+ unsigned int type = dev->device & 0xff00;
-int pci_siig20x_fn(struct pci_dev *dev, int enable)
-{
- int ret = 0;
- if (enable)
- ret = pci_siig20x_init(dev);
- return ret;
-}
+ if (type == 0x1000)
+ return pci_siig10x_init(dev);
+ else if (type == 0x2000)
+ return pci_siig20x_init(dev);
-EXPORT_SYMBOL(pci_siig10x_fn);
-EXPORT_SYMBOL(pci_siig20x_fn);
+ moan_device("Unknown SIIG card", dev);
+ return -ENODEV;
+}
/*
* Timedia has an explosion of boards, and to avoid the PCI table from
@@ -520,7 +490,7 @@
* Ugh, this is ugly as all hell --- TYT
*/
static int
-pci_timedia_setup(struct pci_dev *dev, struct pci_board *board,
+pci_timedia_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar = 0, offset = board->first_offset;
@@ -546,14 +516,15 @@
bar = idx - 2;
}
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/*
* Some Titan cards are also a little weird
*/
static int
-titan_400l_800l_setup(struct pci_dev *dev, struct pci_board *board,
+titan_400l_800l_setup(struct serial_private *priv,
+ struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -570,7 +541,7 @@
offset = (idx - 2) * board->uart_offset;
}
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
static int __devinit pci_xircom_init(struct pci_dev *dev)
@@ -590,7 +561,7 @@
}
static int
-pci_default_setup(struct pci_dev *dev, struct pci_board *board,
+pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset, maxnr;
@@ -601,13 +572,13 @@
else
offset += idx * board->uart_offset;
- maxnr = (pci_resource_len(dev, bar) - board->first_offset) /
+ maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) /
(8 << board->reg_shift);
if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
return 1;
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/* This should be in linux/pci_ids.h */
@@ -751,152 +722,15 @@
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
-
/*
* SIIG cards.
- * It is not clear whether these could be collapsed.
*/
{
.vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_10x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_10x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_10x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_10x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_10x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_10x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_10x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_10x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_10x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_20x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_20x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_20x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_20x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- { .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_20x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_20x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_20x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_20x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_20x_850,
+ .device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
+ .init = pci_siig_init,
.setup = pci_default_setup,
},
/*
@@ -987,7 +821,7 @@
}
static _INLINE_ int
-get_pci_irq(struct pci_dev *dev, struct pci_board *board, int idx)
+get_pci_irq(struct pci_dev *dev, struct pciserial_board *board)
{
if (board->flags & FL_NOIRQ)
return 0;
@@ -1108,7 +942,7 @@
* see first lines of serial_in() and serial_out() in 8250.c
*/
-static struct pci_board pci_boards[] __devinitdata = {
+static struct pciserial_board pci_boards[] __devinitdata = {
[pbn_default] = {
.flags = FL_BASE0,
.num_ports = 1,
@@ -1554,7 +1388,7 @@
* serial specs. Returns 0 on success, 1 on failure.
*/
static int __devinit
-serial_pci_guess_board(struct pci_dev *dev, struct pci_board *board)
+serial_pci_guess_board(struct pci_dev *dev, struct pciserial_board *board)
{
int num_iomem, num_port, first_port = -1, i;
@@ -1619,7 +1453,8 @@
}
static inline int
-serial_pci_matches(struct pci_board *board, struct pci_board *guessed)
+serial_pci_matches(struct pciserial_board *board,
+ struct pciserial_board *guessed)
{
return
board->num_ports == guessed->num_ports &&
@@ -1629,58 +1464,14 @@
board->first_offset == guessed->first_offset;
}
-/*
- * Probe one serial board. Unfortunately, there is no rhyme nor reason
- * to the arrangement of serial ports on a PCI card.
- */
-static int __devinit
-pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
+struct serial_private *
+pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board)
{
+ struct uart_port serial_port;
struct serial_private *priv;
- struct pci_board *board, tmp;
struct pci_serial_quirk *quirk;
int rc, nr_ports, i;
- if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
- printk(KERN_ERR "pci_init_one: invalid driver_data: %ld\n",
- ent->driver_data);
- return -EINVAL;
- }
-
- board = &pci_boards[ent->driver_data];
-
- rc = pci_enable_device(dev);
- if (rc)
- return rc;
-
- if (ent->driver_data == pbn_default) {
- /*
- * Use a copy of the pci_board entry for this;
- * avoid changing entries in the table.
- */
- memcpy(&tmp, board, sizeof(struct pci_board));
- board = &tmp;
-
- /*
- * We matched one of our class entries. Try to
- * determine the parameters of this board.
- */
- rc = serial_pci_guess_board(dev, board);
- if (rc)
- goto disable;
- } else {
- /*
- * We matched an explicit entry. If we are able to
- * detect this boards settings with our heuristic,
- * then we no longer need this entry.
- */
- memcpy(&tmp, &pci_boards[pbn_default], sizeof(struct pci_board));
- rc = serial_pci_guess_board(dev, &tmp);
- if (rc == 0 && serial_pci_matches(board, &tmp))
- moan_device("Redundant entry in serial pci_table.",
- dev);
- }
-
nr_ports = board->num_ports;
/*
@@ -1697,8 +1488,10 @@
*/
if (quirk->init) {
rc = quirk->init(dev);
- if (rc < 0)
- goto disable;
+ if (rc < 0) {
+ priv = ERR_PTR(rc);
+ goto err_out;
+ }
if (rc)
nr_ports = rc;
}
@@ -1707,27 +1500,26 @@
sizeof(unsigned int) * nr_ports,
GFP_KERNEL);
if (!priv) {
- rc = -ENOMEM;
- goto deinit;
+ priv = ERR_PTR(-ENOMEM);
+ goto err_deinit;
}
memset(priv, 0, sizeof(struct serial_private) +
sizeof(unsigned int) * nr_ports);
+ priv->dev = dev;
priv->quirk = quirk;
- pci_set_drvdata(dev, priv);
- for (i = 0; i < nr_ports; i++) {
- struct uart_port serial_port;
- memset(&serial_port, 0, sizeof(struct uart_port));
+ memset(&serial_port, 0, sizeof(struct uart_port));
+ serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+ serial_port.uartclk = board->base_baud * 16;
+ serial_port.irq = get_pci_irq(dev, board);
+ serial_port.dev = &dev->dev;
- serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF |
- UPF_SHARE_IRQ;
- serial_port.uartclk = board->base_baud * 16;
- serial_port.irq = get_pci_irq(dev, board, i);
- serial_port.dev = &dev->dev;
- if (quirk->setup(dev, board, &serial_port, i))
+ for (i = 0; i < nr_ports; i++) {
+ if (quirk->setup(priv, board, &serial_port, i))
break;
+
#ifdef SERIAL_DEBUG_PCI
printk("Setup PCI port: port %x, irq %d, type %d\n",
serial_port.iobase, serial_port.irq, serial_port.iotype);
@@ -1742,58 +1534,152 @@
priv->nr = i;
- return 0;
+ return priv;
- deinit:
+ err_deinit:
if (quirk->exit)
quirk->exit(dev);
- disable:
- pci_disable_device(dev);
- return rc;
+ err_out:
+ return priv;
}
+EXPORT_SYMBOL(pciserial_init_ports);
-static void __devexit pciserial_remove_one(struct pci_dev *dev)
+void pciserial_remove_ports(struct serial_private *priv)
{
- struct serial_private *priv = pci_get_drvdata(dev);
+ struct pci_serial_quirk *quirk;
+ int i;
- pci_set_drvdata(dev, NULL);
+ for (i = 0; i < priv->nr; i++)
+ if (priv->line[i] >= 0)
+ serial8250_unregister_port(priv->line[i]);
- if (priv) {
- struct pci_serial_quirk *quirk;
- int i;
+ for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
+ if (priv->remapped_bar[i])
+ iounmap(priv->remapped_bar[i]);
+ priv->remapped_bar[i] = NULL;
+ }
- for (i = 0; i < priv->nr; i++)
- serial8250_unregister_port(priv->line[i]);
+ /*
+ * Find the exit quirks.
+ */
+ quirk = find_quirk(priv->dev);
+ if (quirk->exit)
+ quirk->exit(priv->dev);
- for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
- if (priv->remapped_bar[i])
- iounmap(priv->remapped_bar[i]);
- priv->remapped_bar[i] = NULL;
- }
+ kfree(priv);
+}
+EXPORT_SYMBOL(pciserial_remove_ports);
+
+void pciserial_suspend_ports(struct serial_private *priv)
+{
+ int i;
+
+ for (i = 0; i < priv->nr; i++)
+ if (priv->line[i] >= 0)
+ serial8250_suspend_port(priv->line[i]);
+}
+EXPORT_SYMBOL(pciserial_suspend_ports);
+
+void pciserial_resume_ports(struct serial_private *priv)
+{
+ int i;
+ /*
+ * Ensure that the board is correctly configured.
+ */
+ if (priv->quirk->init)
+ priv->quirk->init(priv->dev);
+
+ for (i = 0; i < priv->nr; i++)
+ if (priv->line[i] >= 0)
+ serial8250_resume_port(priv->line[i]);
+}
+EXPORT_SYMBOL(pciserial_resume_ports);
+
+/*
+ * Probe one serial board. Unfortunately, there is no rhyme nor reason
+ * to the arrangement of serial ports on a PCI card.
+ */
+static int __devinit
+pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
+{
+ struct serial_private *priv;
+ struct pciserial_board *board, tmp;
+ int rc;
+
+ if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
+ printk(KERN_ERR "pci_init_one: invalid driver_data: %ld\n",
+ ent->driver_data);
+ return -EINVAL;
+ }
+
+ board = &pci_boards[ent->driver_data];
+
+ rc = pci_enable_device(dev);
+ if (rc)
+ return rc;
+
+ if (ent->driver_data == pbn_default) {
/*
- * Find the exit quirks.
+ * Use a copy of the pci_board entry for this;
+ * avoid changing entries in the table.
*/
- quirk = find_quirk(dev);
- if (quirk->exit)
- quirk->exit(dev);
+ memcpy(&tmp, board, sizeof(struct pciserial_board));
+ board = &tmp;
- pci_disable_device(dev);
+ /*
+ * We matched one of our class entries. Try to
+ * determine the parameters of this board.
+ */
+ rc = serial_pci_guess_board(dev, board);
+ if (rc)
+ goto disable;
+ } else {
+ /*
+ * We matched an explicit entry. If we are able to
+ * detect this boards settings with our heuristic,
+ * then we no longer need this entry.
+ */
+ memcpy(&tmp, &pci_boards[pbn_default],
+ sizeof(struct pciserial_board));
+ rc = serial_pci_guess_board(dev, &tmp);
+ if (rc == 0 && serial_pci_matches(board, &tmp))
+ moan_device("Redundant entry in serial pci_table.",
+ dev);
+ }
- kfree(priv);
+ priv = pciserial_init_ports(dev, board);
+ if (!IS_ERR(priv)) {
+ pci_set_drvdata(dev, priv);
+ return 0;
}
+
+ rc = PTR_ERR(priv);
+
+ disable:
+ pci_disable_device(dev);
+ return rc;
+}
+
+static void __devexit pciserial_remove_one(struct pci_dev *dev)
+{
+ struct serial_private *priv = pci_get_drvdata(dev);
+
+ pci_set_drvdata(dev, NULL);
+
+ if (priv)
+ pciserial_remove_ports(priv);
+
+ pci_disable_device(dev);
}
static int pciserial_suspend_one(struct pci_dev *dev, pm_message_t state)
{
struct serial_private *priv = pci_get_drvdata(dev);
- if (priv) {
- int i;
+ if (priv)
+ pciserial_suspend_ports(priv);
- for (i = 0; i < priv->nr; i++)
- serial8250_suspend_port(priv->line[i]);
- }
pci_save_state(dev);
pci_set_power_state(dev, pci_choose_state(dev, state));
return 0;
@@ -1807,21 +1693,12 @@
pci_restore_state(dev);
if (priv) {
- int i;
-
/*
* The device may have been disabled. Re-enable it.
*/
pci_enable_device(dev);
- /*
- * Ensure that the board is correctly configured.
- */
- if (priv->quirk->init)
- priv->quirk->init(dev);
-
- for (i = 0; i < priv->nr; i++)
- serial8250_resume_port(priv->line[i]);
+ pciserial_resume_ports(priv);
}
return 0;
}
Index: include/linux/8250_pci.h
===================================================================
--- 39040c7a05edd69381c0a25636a1a328d856cb9c/include/linux/8250_pci.h (mode:100644)
+++ uncommitted/include/linux/8250_pci.h (mode:100644)
@@ -1,2 +1,39 @@
-int pci_siig10x_fn(struct pci_dev *dev, int enable);
-int pci_siig20x_fn(struct pci_dev *dev, int enable);
+#define PCI_NUM_BAR_RESOURCES 6
+
+/*
+ * Definitions for PCI support.
+ */
+#define FL_BASE_MASK 0x0007
+#define FL_BASE0 0x0000
+#define FL_BASE1 0x0001
+#define FL_BASE2 0x0002
+#define FL_BASE3 0x0003
+#define FL_BASE4 0x0004
+#define FL_GET_BASE(x) (x & FL_BASE_MASK)
+
+/* Use successive BARs (PCI base address registers),
+ else use offset into some specified BAR */
+#define FL_BASE_BARS 0x0008
+
+/* do not assign an irq */
+#define FL_NOIRQ 0x0080
+
+/* Use the Base address register size to cap number of ports */
+#define FL_REGION_SZ_CAP 0x0100
+
+struct pciserial_board {
+ unsigned int flags;
+ unsigned int num_ports;
+ unsigned int base_baud;
+ unsigned int uart_offset;
+ unsigned int reg_shift;
+ unsigned int first_offset;
+};
+
+struct serial_private;
+
+struct serial_private *
+pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board);
+void __devexit pciserial_remove_ports(struct serial_private *priv);
+void pciserial_suspend_ports(struct serial_private *priv);
+void pciserial_resume_ports(struct serial_private *priv);
Index: include/linux/serialP.h
===================================================================
--- 39040c7a05edd69381c0a25636a1a328d856cb9c/include/linux/serialP.h (mode:100644)
+++ uncommitted/include/linux/serialP.h (mode:100644)
@@ -141,44 +141,4 @@
#define ALPHA_KLUDGE_MCR 0
#endif
-/*
- * Definitions for PCI support.
- */
-#define SPCI_FL_BASE_MASK 0x0007
-#define SPCI_FL_BASE0 0x0000
-#define SPCI_FL_BASE1 0x0001
-#define SPCI_FL_BASE2 0x0002
-#define SPCI_FL_BASE3 0x0003
-#define SPCI_FL_BASE4 0x0004
-#define SPCI_FL_GET_BASE(x) (x & SPCI_FL_BASE_MASK)
-
-#define SPCI_FL_IRQ_MASK (0x0007 << 4)
-#define SPCI_FL_IRQBASE0 (0x0000 << 4)
-#define SPCI_FL_IRQBASE1 (0x0001 << 4)
-#define SPCI_FL_IRQBASE2 (0x0002 << 4)
-#define SPCI_FL_IRQBASE3 (0x0003 << 4)
-#define SPCI_FL_IRQBASE4 (0x0004 << 4)
-#define SPCI_FL_GET_IRQBASE(x) ((x & SPCI_FL_IRQ_MASK) >> 4)
-
-/* Use successive BARs (PCI base address registers),
- else use offset into some specified BAR */
-#define SPCI_FL_BASE_TABLE 0x0100
-
-/* Use successive entries in the irq resource table */
-#define SPCI_FL_IRQ_TABLE 0x0200
-
-/* Use the irq resource table instead of dev->irq */
-#define SPCI_FL_IRQRESOURCE 0x0400
-
-/* Use the Base address register size to cap number of ports */
-#define SPCI_FL_REGION_SZ_CAP 0x0800
-
-/* Do not use irq sharing for this device */
-#define SPCI_FL_NO_SHIRQ 0x1000
-
-/* This is a PNP device */
-#define SPCI_FL_ISPNP 0x2000
-
-#define SPCI_FL_PNPDEFAULT (SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP)
-
#endif /* _LINUX_SERIAL_H */
--
Russell King
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of: 2.6 Serial core
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
