PATCH: it8212 backport for Bartlomiej IDE (Correct diff)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Llu, 2005-06-20 at 21:39, Alan Cox wrote:
> This lets you throw out the iteraid stuff that has ended up back in due
> to stupid goings on in the IDE world. Its the same heavily tested code
> shipped in Fedora/Red Hat products but without the other dependancies on
> the Bartlomiej IDE layer.
> 
> Pre-requisite: the ide-disk patch I sent to handle pure LBA devices.
> 
> Obviously you lose things like hot unplug with the Bartlomiej IDE layer
> at the moment but that won't matter to most users.
> 
> The patch does the following
> - Add IT8211/12 to pci_ids.h
> - Add Makefile/Kconfig entry
> - Add it8212 driver
      * 
      * No core IDE code is touched by this diff
      * 
      * Signed-off-by: Alan Cox <[email protected]>
      * Embedded system testing and the ability to force raid mode off
        by David
      * Howells
      * 
      * Made possible by the ite reference code, documentation and also
        several
> clarifications and pieces of assistance provided by ITE themselves

Attached the wrong diff. Please use the one below

diff -u --new-file --recursive --exclude-from /usr/src/exclude linux.vanilla-2.6.12/drivers/ide/Kconfig linux-2.6.12/drivers/ide/Kconfig
--- linux.vanilla-2.6.12/drivers/ide/Kconfig	2005-06-19 11:30:47.000000000 +0100
+++ linux-2.6.12/drivers/ide/Kconfig	2005-06-20 21:24:36.762827768 +0100
@@ -606,6 +606,12 @@
 	  <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
 	  board at <http://www.mvista.com/partners/semiconductor/ite.html>.
 
+config BLK_DEV_IT821X
+	tristate "IT821X IDE support"
+	help
+	  This driver adds support for the ITE 8211 IDE controller and the
+	  IT 8212 IDE RAID controller in both RAID and pass-through mode. 
+
 config BLK_DEV_NS87415
 	tristate "NS87415 chipset support"
 	help
diff -u --new-file --recursive --exclude-from /usr/src/exclude linux.vanilla-2.6.12/drivers/ide/pci/it821x.c linux-2.6.12/drivers/ide/pci/it821x.c
--- linux.vanilla-2.6.12/drivers/ide/pci/it821x.c	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.12/drivers/ide/pci/it821x.c	2005-06-20 21:27:07.000000000 +0100
@@ -0,0 +1,812 @@
+
+/*
+ * linux/drivers/ide/pci/it821x.c		Version 0.09	December 2004
+ *
+ * Copyright (C) 2004		Red Hat <[email protected]>
+ *
+ *  May be copied or modified under the terms of the GNU General Public License
+ *  Based in part on the ITE vendor provided SCSI driver.
+ *
+ *  Documentation available from
+ * 	http://www.ite.com.tw/pc/IT8212F_V04.pdf
+ *  Some other documents are NDA.
+ *
+ *  The ITE8212 isn't exactly a standard IDE controller. It has two
+ *  modes. In pass through mode then it is an IDE controller. In its smart
+ *  mode its actually quite a capable hardware raid controller disguised
+ *  as an IDE controller. Smart mode only understands DMA read/write and
+ *  identify, none of the fancier commands apply. The IT8211 is identical
+ *  in other respects but lacks the raid mode.
+ *
+ *  Errata:
+ *  o	Rev 0x10 also requires master/slave hold the same DMA timings and
+ *	cannot do ATAPI MWDMA. 
+ *  o	The identify data for raid volumes lacks CHS info (technically ok)
+ *	but also fails to set the LBA28 and other bits. We fix these in
+ *	the IDE probe quirk code.
+ *  o	If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
+ *	raid then the controller firmware dies
+ *  o	Smart mode without RAID doesn't clear all the necessary identify
+ *	bits to reduce the command set to the one used
+ *
+ *  This has a few impacts on the driver
+ *  - In pass through mode we do all the work you would expect
+ *  - In smart mode the clocking set up is done by the controller generally
+ *    but we must watch the other limits and filter.
+ *  - There are a few extra vendor commands that actually talk to the
+ *    controller but only work PIO with no IRQ.
+ *
+ *  Vendor areas of the identify block in smart mode are used for the
+ *  timing and policy set up. Each HDD in raid mode also has a serial
+ *  block on the disk. The hardware extra commands are get/set chip status,
+ *  rebuild, get rebuild status.
+ *
+ *  In Linux the driver supports pass through mode as if the device was
+ *  just another IDE controller. If the smart mode is running then
+ *  volumes are managed by the controller firmware and each IDE "disk"
+ *  is a raid volume. Even more cute - the controller can do automated
+ *  hotplug and rebuild.
+ *
+ *  The pass through controller itself is a little demented. It has a
+ *  flaw that it has a single set of PIO/MWDMA timings per channel so
+ *  non UDMA devices restrict each others performance. It also has a
+ *  single clock source per channel so mixed UDMA100/133 performance
+ *  isn't perfect and we have to pick a clock. Thankfully none of this
+ *  matters in smart mode. ATAPI DMA is not currently supported.
+ *
+ *  It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
+ *
+ *  TODO
+ *	-	ATAPI UDMA is ok but not MWDMA it seems
+ *	-	RAID configuration ioctls
+ *	-	Move to libata once it grows up
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/hdreg.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+struct it821x_dev
+{
+	unsigned int smart:1,		/* Are we in smart raid mode */
+		timing10:1;		/* Rev 0x10 */
+	u8	clock_mode;		/* 0, ATA_50 or ATA_66 */
+	u8	want[2][2];		/* Mode/Pri log for master slave */
+	/* We need these for switching the clock when DMA goes on/off
+	   The high byte is the 66Mhz timing */
+	u16	pio[2];			/* Cached PIO values */
+	u16	mwdma[2];		/* Cached MWDMA values */
+	u16	udma[2];		/* Cached UDMA values (per drive) */
+};
+
+#define ATA_66		0
+#define ATA_50		1
+#define ATA_ANY		2
+
+#define UDMA_OFF	0
+#define MWDMA_OFF	0
+
+/*
+ *	We allow users to force the card into non raid mode without
+ *	flashing the alternative BIOS. This is also neccessary right now
+ *	for embedded platforms that cannot run a PC BIOS but are using this
+ *	device.
+ */
+ 
+static int it8212_noraid;
+
+/**
+ *	it821x_program	-	program the PIO/MWDMA registers
+ *	@drive: drive to tune
+ *
+ *	Program the PIO/MWDMA timing for this channel according to the
+ *	current clock.
+ */
+
+static void it821x_program(ide_drive_t *drive, u16 timing)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int channel = hwif->channel;
+	u8 conf;
+
+	/* Program PIO/MWDMA timing bits */
+	if(itdev->clock_mode == ATA_66)
+		conf = timing >> 8;
+	else	
+		conf = timing & 0xFF;
+	pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * channel, conf);
+}
+
+/**
+ *	it821x_program_udma	-	program the UDMA registers
+ *	@drive: drive to tune
+ *
+ *	Program the UDMA timing for this drive according to the
+ *	current clock.
+ */
+
+static void it821x_program_udma(ide_drive_t *drive, u16 timing)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int channel = hwif->channel;
+	int unit = drive->select.b.unit;
+	u8 conf;
+	
+	/* Program UDMA timing bits */
+	if(itdev->clock_mode == ATA_66)
+		conf = timing >> 8;
+	else
+		conf = timing & 0xFF;
+	if(itdev->timing10 == 0)
+		pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + unit, conf);
+	else {
+		pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel, conf);
+		pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + 1, conf);
+	}
+}
+
+
+/**
+ *	it821x_clock_strategy
+ *	@hwif: hardware interface
+ *
+ *	Select between the 50 and 66Mhz base clocks to get the best
+ *	results for this interface.
+ */
+
+static void it821x_clock_strategy(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+
+	u8 unit = drive->select.b.unit;
+	ide_drive_t *pair = &hwif->drives[1-unit];
+
+	int clock, altclock;
+	u8 v;
+	int sel = 0;
+
+	if(itdev->want[0][0] > itdev->want[1][0]) {
+		clock = itdev->want[0][1];
+		altclock = itdev->want[1][1];
+	} else {
+		clock = itdev->want[1][1];
+		altclock = itdev->want[0][1];
+	}
+
+	/* Master doesn't care does the slave ? */
+	if(clock == ATA_ANY)
+		clock = altclock;
+		
+	/* Nobody cares - keep the same clock */
+	if(clock == ATA_ANY)
+		return;
+	/* No change */
+	if(clock == itdev->clock_mode)
+		return;
+		
+	/* Load this into the controller ? */
+	if(clock == ATA_66)
+		itdev->clock_mode = ATA_66;
+	else {
+		itdev->clock_mode = ATA_50;
+		sel = 1;
+	}
+	pci_read_config_byte(hwif->pci_dev, 0x50, &v);
+	v &= ~(1 << (1 + hwif->channel));
+	v |= sel << (1 + hwif->channel);
+	pci_write_config_byte(hwif->pci_dev, 0x50, v);
+	
+	/*
+	 *	Reprogram the UDMA/PIO of the pair drive for the switch
+	 *	MWDMA will be dealt with by the dma switcher
+	 */
+	if(pair && itdev->udma[1-unit] != UDMA_OFF) {
+		it821x_program_udma(pair, itdev->udma[1-unit]);
+		it821x_program(pair, itdev->pio[1-unit]);
+	}
+	/*
+	 *	Reprogram the UDMA/PIO of our drive for the switch.
+	 *	MWDMA will be dealt with by the dma switcher
+	 */
+	if(itdev->udma[unit] != UDMA_OFF) {
+		it821x_program_udma(drive, itdev->udma[unit]);
+		it821x_program(drive, itdev->pio[unit]);
+	}
+}
+
+/**
+ *	it821x_ratemask	-	Compute available modes
+ *	@drive: IDE drive
+ *
+ *	Compute the available speeds for the devices on the interface. This
+ *	is all modes to ATA133 clipped by drive cable setup.
+ */
+
+static u8 it821x_ratemask (ide_drive_t *drive)
+{
+	u8 mode	= 4;
+	if (!eighty_ninty_three(drive))
+		mode = min(mode, (u8)1);
+	return mode;
+}
+
+/**
+ *	it821x_tuneproc	-	tune a drive
+ *	@drive: drive to tune
+ *	@mode_wanted: the target operating mode
+ *
+ *	Load the timing settings for this device mode into the
+ *	controller. By the time we are called the mode has been
+ *	modified as neccessary to handle the absence of seperate
+ *	master/slave timers for MWDMA/PIO.
+ *
+ *	This code is only used in pass through mode.
+ */
+
+static void it821x_tuneproc (ide_drive_t *drive, byte mode_wanted)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int unit = drive->select.b.unit;
+	
+	/* Spec says 89 ref driver uses 88 */
+	static u16 pio[]	= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
+	static u8 pio_want[]    = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
+	
+	if(itdev->smart)
+		return;
+
+	/* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
+	itdev->want[unit][1] = pio_want[mode_wanted];
+	itdev->want[unit][0] = 1;	/* PIO is lowest priority */
+	itdev->pio[unit] = pio[mode_wanted];
+	it821x_clock_strategy(drive);
+	it821x_program(drive, itdev->pio[unit]);
+}
+
+/**
+ *	it821x_tune_mwdma	-	tune a channel for MWDMA
+ *	@drive: drive to set up
+ *	@mode_wanted: the target operating mode
+ *
+ *	Load the timing settings for this device mode into the
+ *	controller when doing MWDMA in pass through mode. The caller
+ *	must manage the whole lack of per device MWDMA/PIO timings and
+ *	the shared MWDMA/PIO timing register.
+ */
+
+static void it821x_tune_mwdma (ide_drive_t *drive, byte mode_wanted)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif);
+	int unit = drive->select.b.unit;
+	int channel = hwif->channel;
+	u8 conf;
+	
+	static u16 dma[]	= { 0x8866, 0x3222, 0x3121 };
+	static u8 mwdma_want[]	= { ATA_ANY, ATA_66, ATA_ANY };
+	
+	itdev->want[unit][1] = mwdma_want[mode_wanted];
+	itdev->want[unit][0] = 2;	/* MWDMA is low priority */
+	itdev->mwdma[unit] = dma[mode_wanted];
+	itdev->udma[unit] = UDMA_OFF;
+	
+	/* UDMA bits off - Revision 0x10 do them in pairs */
+	pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
+	if(itdev->timing10)
+		conf |= channel ? 0x60: 0x18;
+	else
+		conf |= 1 << (3 + 2 * channel + unit);
+	pci_write_config_byte(hwif->pci_dev, 0x50, conf);
+
+	it821x_clock_strategy(drive);
+	/* FIXME: do we need to program this ? */
+	/* it821x_program(drive, itdev->mwdma[unit]); */
+}
+
+/**
+ *	it821x_tune_udma	-	tune a channel for UDMA
+ *	@drive: drive to set up
+ *	@mode_wanted: the target operating mode
+ *
+ *	Load the timing settings for this device mode into the
+ *	controller when doing UDMA modes in pass through.
+ */
+
+static void it821x_tune_udma (ide_drive_t *drive, byte mode_wanted)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int unit = drive->select.b.unit;
+	int channel = hwif->channel;
+	u8 conf;
+
+	static u16 udma[]	= { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
+	static u8 udma_want[]	= { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
+	
+	itdev->want[unit][1] = udma_want[mode_wanted];
+	itdev->want[unit][0] = 3;	/* UDMA is high priority */
+	itdev->mwdma[unit] = MWDMA_OFF;
+	itdev->udma[unit] = udma[mode_wanted];
+	if(mode_wanted >= 5)
+		itdev->udma[unit] |= 0x8080;	/* UDMA 5/6 select on */
+		
+	/* UDMA on. Again revision 0x10 must do the pair */
+	pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
+	if(itdev->timing10)
+		conf &= channel ? 0x9F: 0xE7;
+	else
+		conf &= ~ (1 << (3 + 2 * channel + unit));
+	pci_write_config_byte(hwif->pci_dev, 0x50, conf);
+
+	it821x_clock_strategy(drive);
+	it821x_program_udma(drive, itdev->udma[unit]);
+	
+}
+
+/**
+ *	config_it821x_chipset_for_pio	-	set drive timings
+ *	@drive: drive to tune
+ *	@speed we want
+ *
+ *	Compute the best pio mode we can for a given device. We must
+ *	pick a speed that does not cause problems with the other device
+ *	on the cable.
+ */
+
+static void config_it821x_chipset_for_pio (ide_drive_t *drive, byte set_speed)
+{
+	u8 unit = drive->select.b.unit;
+	ide_hwif_t *hwif = drive->hwif;
+	ide_drive_t *pair = &hwif->drives[1-unit];
+	u8 speed = 0, set_pio	= ide_get_best_pio_mode(drive, 255, 5, NULL);
+	u8 pair_pio;
+	
+	/* We have to deal with this mess in pairs */
+	if(pair != NULL) {
+		pair_pio = ide_get_best_pio_mode(pair, 255, 5, NULL);
+		/* Trim PIO to the slowest of the master/slave */
+		if(pair_pio < set_pio)
+			set_pio = pair_pio;
+	}
+	it821x_tuneproc(drive, set_pio);
+	speed = XFER_PIO_0 + set_pio;
+	/* XXX - We trim to the lowest of the pair so the other drive
+	   will always be fine at this point until we do hotplug passthru */
+
+	if (set_speed)
+		(void) ide_config_drive_speed(drive, speed);
+}
+
+/**
+ *	it821x_dma_read	-	DMA hook
+ *	@drive: drive for DMA
+ *
+ *	The IT821x has a single timing register for MWDMA and for PIO
+ *	operations. As we flip back and forth we have to reload the
+ *	clock. In addition the rev 0x10 device only works if the same
+ *	timing value is loaded into the master and slave UDMA clock
+ * 	so we must also reload that.
+ *
+ *	FIXME: we could figure out in advance if we need to do reloads
+ */
+
+static void it821x_dma_start(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int unit = drive->select.b.unit;
+	if(itdev->mwdma[unit] != MWDMA_OFF)
+		it821x_program(drive, itdev->mwdma[unit]);
+	else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10)
+		it821x_program_udma(drive, itdev->udma[unit]);
+	ide_dma_start(drive);
+}
+
+/**
+ *	it821x_dma_write	-	DMA hook
+ *	@drive: drive for DMA stop
+ *
+ *	The IT821x has a single timing register for MWDMA and for PIO
+ *	operations. As we flip back and forth we have to reload the
+ *	clock.
+ */
+
+static int it821x_dma_end(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	int unit = drive->select.b.unit;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int ret = __ide_dma_end(drive);
+	if(itdev->mwdma[unit] != MWDMA_OFF)
+		it821x_program(drive, itdev->pio[unit]);
+	return ret;
+}
+
+	
+/**
+ *	it821x_tune_chipset	-	set controller timings
+ *	@drive: Drive to set up
+ *	@xferspeed: speed we want to achieve
+ *
+ *	Tune the ITE chipset for the desired mode. If we can't achieve
+ *	the desired mode then tune for a lower one, but ultimately
+ *	make the thing work.
+ */
+
+static int it821x_tune_chipset (ide_drive_t *drive, byte xferspeed)
+{
+
+	ide_hwif_t *hwif	= drive->hwif;
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	u8 speed		= ide_rate_filter(it821x_ratemask(drive), xferspeed);
+
+	if(!itdev->smart) {
+		switch(speed) {
+			case XFER_PIO_4:
+			case XFER_PIO_3:
+			case XFER_PIO_2:
+			case XFER_PIO_1:
+			case XFER_PIO_0:
+				it821x_tuneproc(drive, (speed - XFER_PIO_0));
+				break;
+			/* MWDMA tuning is really hard because our MWDMA and PIO
+			   timings are kept in the same place. We can switch in the
+			   host dma on/off callbacks */
+			case XFER_MW_DMA_2:
+			case XFER_MW_DMA_1:
+			case XFER_MW_DMA_0:
+				it821x_tune_mwdma(drive, (speed - XFER_MW_DMA_0));
+				break;
+			case XFER_UDMA_6:
+			case XFER_UDMA_5:
+			case XFER_UDMA_4:
+			case XFER_UDMA_3:
+			case XFER_UDMA_2:
+			case XFER_UDMA_1:
+			case XFER_UDMA_0:
+				it821x_tune_udma(drive, (speed - XFER_UDMA_0));
+				break;
+			default:
+				return 1;
+		}
+	}
+	/*
+	 *	In smart mode the clocking is done by the host controller
+	 * 	snooping the mode we picked. The rest of it is not our problem
+	 */
+	return ide_config_drive_speed(drive, speed);
+}
+
+/**
+ *	config_chipset_for_dma	-	configure for DMA
+ *	@drive: drive to configure
+ *
+ *	Called by the IDE layer when it wants the timings set up.
+ */
+
+static int config_chipset_for_dma (ide_drive_t *drive)
+{
+	u8 speed	= ide_dma_speed(drive, it821x_ratemask(drive));
+
+	config_it821x_chipset_for_pio(drive, !speed);
+	it821x_tune_chipset(drive, speed);
+	return ide_dma_enable(drive);
+}
+
+/**
+ *	it821x_configure_drive_for_dma	-	set up for DMA transfers
+ *	@drive: drive we are going to set up
+ *
+ *	Set up the drive for DMA, tune the controller and drive as
+ *	required. If the drive isn't suitable for DMA or we hit
+ *	other problems then we will drop down to PIO and set up
+ *	PIO appropriately
+ */
+
+static int it821x_config_drive_for_dma (ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+
+	if (ide_use_dma(drive)) {
+		if (config_chipset_for_dma(drive))
+			return hwif->ide_dma_on(drive);
+	}
+	config_it821x_chipset_for_pio(drive, 1);
+	return hwif->ide_dma_off_quietly(drive);
+}
+
+/**
+ *	ata66_it821x	-	check for 80 pin cable
+ *	@hwif: interface to check
+ *
+ *	Check for the presence of an ATA66 capable cable on the
+ *	interface. Problematic as it seems some cards don't have
+ *	the needed logic onboard.
+ */
+
+static unsigned int __devinit ata66_it821x(ide_hwif_t *hwif)
+{
+	/* The reference driver also only does disk side */
+	return 1;
+}
+
+/**
+ *	it821x_fixup	-	post init callback
+ *	@hwif: interface
+ *
+ *	This callback is run after the drives have been probed but
+ *	before anything gets attached. It allows drivers to do any 
+ *	final tuning that is needed, or fixups to work around bugs.
+ */
+
+static void __devinit it821x_fixups(ide_hwif_t *hwif)
+{
+	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+	int i;
+
+	if(!itdev->smart) {
+		/*
+		 *	If we are in pass through mode then not much
+		 *	needs to be done, but we do bother to clear the
+		 *	IRQ mask as we may well be in PIO (eg rev 0x10)
+		 *	for now and we know unmasking is safe on this chipset.
+		 */
+		for (i = 0; i < 2; i++) {
+			ide_drive_t *drive = &hwif->drives[i];
+			if(drive->present)
+				drive->unmask = 1;
+		}
+		return;
+	}
+	/*
+	 *	Perform fixups on smart mode. We need to "lose" some
+	 *	capabilities the firmware lacks but does not filter, and
+	 *	also patch up some capability bits that it forgets to set
+	 *	in RAID mode.
+	 */
+	
+	for(i = 0; i < 2; i++) {
+		ide_drive_t *drive = &hwif->drives[i];
+		struct hd_driveid *id;
+		u16 *idbits;
+		
+		if(!drive->present)
+			continue;
+		id = drive->id;
+		idbits = (u16 *)drive->id;
+		
+		/* Check for RAID v native */
+		if(strstr(id->model, "Integrated Technology Express")) {
+			/* In raid mode the ident block is slightly buggy
+			   We need to set the bits so that the IDE layer knows
+			   LBA28. LBA48 and DMA ar valid */
+			id->capability |= 3;		/* LBA28, DMA */
+			id->command_set_2 |= 0x0400;	/* LBA48 valid */
+			id->cfs_enable_2 |= 0x0400;	/* LBA48 on */
+			/* Reporting logic */
+			printk(KERN_INFO "%s: IT8212 %sRAID %d volume",
+				drive->name,
+				idbits[147] ? "Bootable ":"",
+				idbits[129]);
+				if(idbits[129] != 1)
+					printk("(%dK stripe)", idbits[146]);
+				printk(".\n");
+			/* Now the core code will have wrongly decided no DMA 
+			   so we need to fix this */
+			hwif->ide_dma_off_quietly(drive);
+#ifdef CONFIG_IDEDMA_ONLYDISK
+			if (drive->media == ide_disk)
+#endif
+				hwif->ide_dma_check(drive);
+		} else {
+			/* Non RAID volume. Fixups to stop the core code 
+			   doing unsupported things */
+			id->field_valid &= 1;
+			id->queue_depth = 0;
+			id->command_set_1 = 0;
+			id->command_set_2 &= 0xC400;
+			id->cfsse &= 0xC000;
+			id->cfs_enable_1 = 0;
+			id->cfs_enable_2 &= 0xC400;
+			id->csf_default &= 0xC000;
+			id->word127 = 0;
+			id->dlf = 0;
+			id->csfo = 0;
+			id->cfa_power = 0;
+			printk(KERN_INFO "%s: Performing identify fixups.\n",
+				drive->name);
+		}
+	}
+	
+}
+
+/**
+ *	init_hwif_it821x	-	set up hwif structs
+ *	@hwif: interface to set up
+ *
+ *	We do the basic set up of the interface structure. The IT8212
+ *	requires several custom handlers so we override the default
+ *	ide DMA handlers appropriately
+ */
+
+static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
+{
+	struct it821x_dev *idev = kmalloc(sizeof(struct it821x_dev), GFP_KERNEL);
+	u8 conf;
+
+	if(idev == NULL) {
+		printk(KERN_ERR "it821x: out of memory, falling back to legacy behaviour.\n");
+		goto fallback;
+	}
+	memset(idev, 0, sizeof(struct it821x_dev));
+	ide_set_hwifdata(hwif, idev);
+
+	pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
+	if(conf & 1) {
+		idev->smart = 1;
+		hwif->atapi_dma = 0;
+		/* Long I/O's although allowed in LBA48 space cause the
+		   onboard firmware to enter the twighlight zone */
+		hwif->rqsize = 256;
+	}
+
+	/* Pull the current clocks from 0x50 also */
+	if (conf & (1 << (1 + hwif->channel)))
+		idev->clock_mode = ATA_50;
+	else
+		idev->clock_mode = ATA_66;
+		
+	idev->want[0][1] = ATA_ANY;
+	idev->want[1][1] = ATA_ANY;
+		
+	/*
+	 *	Not in the docs but according to the reference driver
+	 *	this is neccessary. 
+	 */
+
+	pci_read_config_byte(hwif->pci_dev, 0x08, &conf);
+	if(conf == 0x10) {
+		idev->timing10 = 1;
+		hwif->atapi_dma = 0;
+		if(!idev->smart)
+			printk(KERN_WARNING "it821x: Revision 0x10, workarounds activated.\n");
+	}
+		
+	hwif->speedproc = &it821x_tune_chipset;
+	hwif->tuneproc	= &it821x_tuneproc;
+	
+	/* MWDMA/PIO clock switching for pass through mode */
+	if(!idev->smart) {
+		hwif->dma_start = &it821x_dma_start;
+		hwif->ide_dma_end = &it821x_dma_end;
+	}
+
+	hwif->drives[0].autotune = 1;
+	hwif->drives[1].autotune = 1;
+
+	if (!hwif->dma_base)
+		goto fallback;
+
+	hwif->ultra_mask = 0x7f;
+	hwif->mwdma_mask = 0x07;
+	hwif->swdma_mask = 0x07;
+
+	hwif->ide_dma_check = &it821x_config_drive_for_dma;
+	if (!(hwif->udma_four))
+		hwif->udma_four = ata66_it821x(hwif);
+
+	/*
+	 *	The BIOS often doesn't set up DMA on this controller
+	 *	so we always do it.
+	 */
+
+	hwif->autodma = 1;
+	hwif->drives[0].autodma = hwif->autodma;
+	hwif->drives[1].autodma = hwif->autodma;
+	return;
+fallback:
+	hwif->autodma = 0;
+	return;
+}
+
+static void __devinit it8212_disable_raid(struct pci_dev *dev)
+{
+	/* Reset local CPU, and set BIOS not ready */
+	pci_write_config_byte(dev, 0x5E, 0x01);
+
+	/* Set to bypass mode, and reset PCI bus */
+	pci_write_config_byte(dev, 0x50, 0x00);
+	pci_write_config_word(dev, PCI_COMMAND,
+			      PCI_COMMAND_PARITY | PCI_COMMAND_IO |
+			      PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+	pci_write_config_word(dev, 0x40, 0xA0F3);
+
+	pci_write_config_dword(dev,0x4C, 0x02040204);
+	pci_write_config_byte(dev, 0x42, 0x36);
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0);
+}
+
+static unsigned int __devinit init_chipset_it821x(struct pci_dev *dev, const char *name)
+{
+	u8 conf;
+	static char *mode[2] = { "pass through", "smart" };
+
+	/* Force the card into bypass mode if so requested */
+	if (it8212_noraid) {
+		printk(KERN_INFO "it8212: forcing bypass mode.\n");
+		it8212_disable_raid(dev);
+	}
+	pci_read_config_byte(dev, 0x50, &conf);
+	printk(KERN_INFO "it821x: controller in %s mode.\n", mode[conf & 1]);
+	return 0;
+}
+
+
+#define DECLARE_ITE_DEV(name_str)			\
+	{						\
+		.name		= name_str,		\
+		.init_chipset	= init_chipset_it821x,	\
+		.init_hwif	= init_hwif_it821x,	\
+		.channels	= 2,			\
+		.autodma	= AUTODMA,		\
+		.bootable	= ON_BOARD,		\
+		.fixup	 	= it821x_fixups		\
+	}
+
+static ide_pci_device_t it821x_chipsets[] __devinitdata = {
+	/* 0 */ DECLARE_ITE_DEV("IT8212"),
+};
+
+/**
+ *	it821x_init_one	-	pci layer discovery entry
+ *	@dev: PCI device
+ *	@id: ident table entry
+ *
+ *	Called by the PCI code when it finds an ITE821x controller.
+ *	We then use the IDE PCI generic helper to do most of the work.
+ */
+
+static int __devinit it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	ide_setup_pci_device(dev, &it821x_chipsets[id->driver_data]);
+	return 0;
+}
+
+static struct pci_device_id it821x_pci_tbl[] = {
+	{ PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{ PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{ 0, },
+};
+
+MODULE_DEVICE_TABLE(pci, it821x_pci_tbl);
+
+static struct pci_driver driver = {
+	.name		= "ITE821x IDE",
+	.id_table	= it821x_pci_tbl,
+	.probe		= it821x_init_one,
+};
+
+static int __init it821x_ide_init(void)
+{
+	return ide_pci_register_driver(&driver);
+}
+
+module_init(it821x_ide_init);
+
+module_param_named(noraid, it8212_noraid, int, S_IRUGO);
+MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode");
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("PCI driver module for the ITE 821x");
+MODULE_LICENSE("GPL");
diff -u --new-file --recursive --exclude-from /usr/src/exclude linux.vanilla-2.6.12/drivers/ide/pci/Makefile linux-2.6.12/drivers/ide/pci/Makefile
--- linux.vanilla-2.6.12/drivers/ide/pci/Makefile	2005-06-19 11:21:23.000000000 +0100
+++ linux-2.6.12/drivers/ide/pci/Makefile	2005-06-20 20:41:44.000000000 +0100
@@ -12,6 +12,7 @@
 obj-$(CONFIG_BLK_DEV_HPT366)		+= hpt366.o
 #obj-$(CONFIG_BLK_DEV_HPT37X)		+= hpt37x.o
 obj-$(CONFIG_BLK_DEV_IT8172)		+= it8172.o
+obj-$(CONFIG_BLK_DEV_IT821X)		+= it821x.o
 obj-$(CONFIG_BLK_DEV_NS87415)		+= ns87415.o
 obj-$(CONFIG_BLK_DEV_OPTI621)		+= opti621.o
 obj-$(CONFIG_BLK_DEV_PDC202XX_OLD)	+= pdc202xx_old.o
diff -u --new-file --recursive --exclude-from /usr/src/exclude linux.vanilla-2.6.12/include/linux/pci_ids.h linux-2.6.12/include/linux/pci_ids.h
--- linux.vanilla-2.6.12/include/linux/pci_ids.h	2005-06-19 11:30:59.000000000 +0100
+++ linux-2.6.12/include/linux/pci_ids.h	2005-06-20 21:25:36.400761424 +0100
@@ -1810,6 +1810,8 @@
 #define PCI_VENDOR_ID_ITE		0x1283
 #define PCI_DEVICE_ID_ITE_IT8172G	0x8172
 #define PCI_DEVICE_ID_ITE_IT8172G_AUDIO 0x0801
+#define PCI_DEVICE_ID_ITE_8211		0x8211
+#define PCI_DEVICE_ID_ITE_8212		0x8212
 #define PCI_DEVICE_ID_ITE_8872		0x8872
 #define PCI_DEVICE_ID_ITE_IT8330G_0	0xe886
 

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[Index of Archives]     [Kernel Newbies]     [Netfilter]     [Bugtraq]     [Photo]     [Stuff]     [Gimp]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Video 4 Linux]     [Linux for the blind]     [Linux Resources]
  Powered by Linux