Hi,
pci=routeirq does not solve it.
cardctl status still reports [ready], [bat low]
I attached various outputs that I found useful.
report_2.6_pcirouteirq_poweroff.txt is 2.6 kernel with pci=routeirq kernel
boot option.
report_2.6_poweroff.txt is 2.6 kernel without pci=... kernel boot option.
Additionally I gave output of 2.4 kernel with kernel option pci=routeirq
(which is discarded...).
We also tried several permutations of the kernel options acpi=off,
irq_mode=0, p2cclk=1 and pci=routeirq to no avail.
Any other ideas?
Thanks,
Markus Becker
---
Dipl.-Ing. Markus Becker | web: http://www.comnets.uni-bremen.de/~mab/
Communication Networks | mailto: [email protected]
University Bremen, Germany | telephone: +49 421 218 2287
***dmesg
Linux version 2.4.27-2-386 ([email protected]) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Mon May 16 16:47:51 JST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b000 (usable)
BIOS-e820: 000000000009b000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001eff0000 (usable)
BIOS-e820: 000000001eff0000 - 000000001eff3000 (ACPI NVS)
BIOS-e820: 000000001eff3000 - 000000001f000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
495MB LOWMEM available.
On node 0 totalpages: 126960
zone(0): 4096 pages.
zone(1): 122864 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 ARBOR ) @ 0x000f64e0
ACPI: RSDT (v001 ARBOR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1eff3000
ACPI: FADT (v001 ARBOR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1eff3040
ACPI: DSDT (v001 ARBOR AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
Kernel command line: root=/dev/hdc1 ro pci=routeirq
PCI: Unknown option `routeirq'
No local APIC present or hardware disabled
Initializing CPU#0
Detected 799.866 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1464.72 BogoMIPS
Memory: 496296k/507840k available (1069k kernel code, 11140k reserved, 459k data, 96k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 512K (128 bytes/line)
CPU: Processor revision 1.4.1.0, 800 MHz
CPU: Code Morphing Software revision 4.3.3-9-510
CPU: 20020910 22:28 official release 4.3.3#5
CPU serial number disabled.
CPU: After generic, caps: 0080893f 0081813f 000000ce 00000000
CPU: Common caps: 0080893f 0081813f 000000ce 00000000
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 stepping 03
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfafe0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
PCI: Disabling Via external APIC routing
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x0
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <[email protected]>
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3744 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
Freeing initrd memory: 3744k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 96k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide: late registration of driver.
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdc:pio, hdd:pio
hdc: SAMSUNG CF/ATA, CFA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: attached ide-disk driver.
hdc: 2041200 sectors (1045 MB) w/0KiB Cache, CHS=2025/16/63
Partition check:
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
Journalled Block Device driver loaded
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 82112k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,1), internal journal
Real Time Clock Driver v1.10f
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
SCSI subsystem driver Revision: 1.00
parport0: PC-style at 0x378 [PCSPP,EPP]
parport_pc: Via 686A parallel port: io=0x378
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 5 for device 00:0b.0
PCI: Sharing IRQ 5 with 00:07.2
PCI: Sharing IRQ 5 with 00:07.3
PCI: Sharing IRQ 5 with 00:0b.1
PCI: Found IRQ 5 for device 00:0b.1
PCI: Sharing IRQ 5 with 00:07.2
PCI: Sharing IRQ 5 with 00:07.3
PCI: Sharing IRQ 5 with 00:0b.0
Yenta ISA IRQ mask 0x0000, PCI irq 5
Socket status: 30000010
ti113x: Routing card interrupts to PCI
Yenta ISA IRQ mask 0x0000, PCI irq 5
Socket status: 30000006
ti113x: Routing card interrupts to PCI
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 10 for device 00:08.0
PCI: Sharing IRQ 10 with 00:0c.0
eth0: RealTek RTL8139 at 0xc800, 00:05:b7:02:8d:fb, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
PCI: Found IRQ 11 for device 00:0d.0
eth1: RealTek RTL8139 at 0xec00, 00:05:b7:02:53:be, IRQ 11
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
Via 686a/8233/8235 audio driver 1.9.1-ac3
PCI: Found IRQ 12 for device 00:07.5
PCI: Setting latency timer of device 00:07.5 to 64
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
via82cxxx: board #1 at 0xBC00, IRQ 12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 16:52:03 May 16 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:07.2
PCI: Sharing IRQ 5 with 00:07.3
PCI: Sharing IRQ 5 with 00:0b.0
PCI: Sharing IRQ 5 with 00:0b.1
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:07.3
PCI: Sharing IRQ 5 with 00:07.2
PCI: Sharing IRQ 5 with 00:0b.0
PCI: Sharing IRQ 5 with 00:0b.1
usb-uhci.c: USB UHCI at I/O 0xb800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
uhci.c: USB Universal Host Controller Interface driver v1.1
eth0: link down
cs: IO port probe 0x0100-0x04ff: excluding 0x1f0-0x1f7 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
airo: Probing for PCI adapters
airo: Finished probing for PCI adapters
airo: Doing fast bap_reads
airo: MAC enabled eth2 0:40:96:52:54:50
eth2: index 0x05: Vcc 5.0, Vpp 5.0, irq 5, io 0x0100-0x013f
BlueZ Core ver 2.4 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <[email protected]>
BlueZ L2CAP ver 2.3 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <[email protected]>
BlueZ RFCOMM ver 1.1
Copyright (C) 2002 Maxim Krasnyansky <[email protected]>
Copyright (C) 2002 Marcel Holtmann <[email protected]>
***uname -a
Linux pc104-1 2.4.27-2-386 #1 Mon May 16 16:47:51 JST 2005 i686 GNU/Linux
***lspci -v
0000:00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 03)
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: bus master, medium devsel, latency 32
Memory at e4000000 (32-bit, non-prefetchable) [size=1M]
0000:00:00.1 RAM memory: Transmeta Corporation SDRAM controller
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: fast devsel
0000:00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: fast devsel
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at b000 [size=16]
Capabilities: [c0] Power Management version 2
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Flags: medium devsel, IRQ 9
Capabilities: [68] Power Management version 2
0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50)
Subsystem: VIA Technologies, Inc. VT82C686 AC97 Audio Controller
Flags: medium devsel, IRQ 12
I/O ports at bc00 [size=256]
I/O ports at c000 [size=4]
I/O ports at c400 [size=4]
Capabilities: [c0] Power Management version 2
0000:00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at c800 [size=256]
Memory at e410a000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:00:0b.0 CardBus bridge: Texas Instruments PCI1420
Subsystem: Unknown device 3412:7856
Flags: bus master, medium devsel, latency 168, IRQ 5
Memory at e4100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
Memory window 0: e4101000-e4102000 (prefetchable)
Memory window 1: e4103000-e4104000
I/O window 0: 0000cc00-0000d003
I/O window 1: 0000d400-0000d803
16-bit legacy interface ports at 0001
0000:00:0b.1 CardBus bridge: Texas Instruments PCI1420
Subsystem: Unknown device 3412:7856
Flags: bus master, medium devsel, latency 168, IRQ 5
Memory at e4105000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=02, sec-latency=176
Memory window 0: e4106000-e4107000 (prefetchable)
Memory window 1: e4108000-e4109000
I/O window 0: 0000dc00-0000e003
I/O window 1: 0000e400-0000e803
16-bit legacy interface ports at 0001
0000:00:0c.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev c1) (prog-if 00 [VGA])
Subsystem: Silicon Motion, Inc. SM720 Lynx3DM
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 10
Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [40] Power Management version 1
0000:00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at ec00 [size=256]
Memory at e410b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
***lspci -tv
-[00]-+-00.0 Transmeta Corporation LongRun Northbridge
+-00.1 Transmeta Corporation SDRAM controller
+-00.2 Transmeta Corporation BIOS scratchpad
+-07.0 VIA Technologies, Inc. VT82C686 [Apollo Super South]
+-07.1 VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE
+-07.2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
+-07.3 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
+-07.4 VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
+-07.5 VIA Technologies, Inc. VT82C686 AC97 Audio Controller
+-08.0 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
+-0b.0 Texas Instruments PCI1420
+-0b.1 Texas Instruments PCI1420
+-0c.0 Silicon Motion, Inc. SM720 Lynx3DM
\-0d.0 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
***cardctl status
Socket 0:
5V 16-bit PC Card
function 0: [ready]
Socket 1:
no card
***cat /proc/interrupts
CPU0
0: 19267 XT-PIC timer
1: 56 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 0 XT-PIC Texas Instruments PCI1420, Texas Instruments PCI1420 (#2), usb-uhci, usb-uhci, eth2
8: 4 XT-PIC rtc
12: 0 XT-PIC via82cxxx
15: 87245 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
***lsmod | grep yenta
yenta_socket 8804 2
pcmcia_core 38020 0 [airo_cs ds yenta_socket]
***lsmod | grep airo
airo_cs 3108 0 (unused)
airo 38776 0 [airo_cs]
ds 5844 2 [airo_cs]
pcmcia_core 38020 0 [airo_cs ds yenta_socket]
***dmesg
Linux version 2.6.11-1-386 (dilinger@mouth) (gcc version 3.3.6 (Debian 1:3.3.6-5)) #1 Fri May 20 06:15:52 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b000 (usable)
BIOS-e820: 000000000009b000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001eff0000 (usable)
BIOS-e820: 000000001eff0000 - 000000001eff3000 (ACPI NVS)
BIOS-e820: 000000001eff3000 - 000000001f000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
495MB LOWMEM available.
On node 0 totalpages: 126960
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 122864 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 ARBOR ) @ 0x000f64e0
ACPI: RSDT (v001 ARBOR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1eff3000
ACPI: FADT (v001 ARBOR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1eff3040
ACPI: DSDT (v001 ARBOR AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 1f000000 (gap: 1f000000:e0ff0000)
Built 1 zonelists
Kernel command line: root=/dev/hdc1 ro pci=routeirq
__iounmap: bad address c00fffd9
No local APIC present or hardware disabled
mapped APIC to ffffd000 (013e2000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 800.074 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 495944k/507840k available (1387k kernel code, 11204k reserved, 757k data, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1576.96 BogoMIPS (lpj=788480)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0084893f 0081813f 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0084893f 0081813f 000000ce 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 512K (128 bytes/line)
CPU: Processor revision 1.4.1.0, 800 MHz
CPU: Code Morphing Software revision 4.3.3-9-510
CPU: 20020910 22:28 official release 4.3.3#5
CPU serial number disabled.
CPU: After all inits, caps: 0080893f 0081813f 000000ce 00000000 00000000 00000000 00000000
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 stepping 03
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: setting ELCR to 0200 (from 1e20)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4228k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfafe0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** Routing PCI interrupts for all devices because "pci=routeirq"
** was specified. If this was required to make a driver work,
** please email the output of "lspci" to [email protected]
** so I can fix the driver.
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI interrupt 0000:00:07.5[C] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:0b.1[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([email protected])
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Disabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
PCI0 USB0 USB1 UAR1 UAR2 LPT1
ACPI: (supports S0 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4228KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.10 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: SAMSUNG CF/ATA, CFA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hdc: max request size: 128KiB
hdc: 2041200 sectors (1045 MB) w/0KiB Cache, CHS=2025/16/63
hdc: cache flushes not supported
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: hdc1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 348692
ext3_orphan_cleanup: deleting unreferenced inode 348691
EXT3-fs: hdc1: 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 82112k swap on /dev/hdc5. Priority:-1 extents:1
EXT3 FS on hdc1, internal journal
Generic RTC Driver v1.07
Capability LSM initialized
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:00:0b.0 [3412:7856]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0b.0, mfunc 0x00001c02, devctl 0x62
Yenta TI: socket 0000:00:0b.0 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:0b.0 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0000, PCI irq 0
Socket status: 30000010
ACPI: PCI interrupt 0000:00:0b.1[A] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:00:0b.1 [3412:7856]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0b.1, mfunc 0x00001c02, devctl 0x62
Yenta TI: socket 0000:00:0b.1 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:0b.1 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0000, PCI irq 0
Socket status: 30000006
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xc800, 00:05:b7:02:8d:fb, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11
eth1: RealTek RTL8139 at 0xec00, 00:05:b7:02:53:be, IRQ 11
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
ACPI: PCI interrupt 0000:00:07.5[C] -> GSI 12 (level, low) -> IRQ 12
PCI: Setting latency timer of device 0000:00:07.5 to 64
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
via82cxxx: board #1 at 0xBC00, IRQ 12
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 5, io base 0xb400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:07.3: irq 5, io base 0xb800
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Linux agpgart interface v0.100 (c) Dave Jones
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
input: PC Speaker
NET: Registered protocol family 17
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
cs: IO port probe 0x100-0x4ff: excluding 0x1f0-0x1f7 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x1f0-0x1f7 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
airo: Probing for PCI adapters
airo: Finished probing for PCI adapters
0.0: RequestIRQ: Resource in use
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e60a0(lo)
IPv6 over IPv4 tunneling driver
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
eth0: no IPv6 routers present
***uname -a
Linux pc104-1 2.6.11-1-386 #1 Fri May 20 06:15:52 UTC 2005 i686 GNU/Linux
***lspci -v
0000:00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 03)
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: bus master, medium devsel, latency 32
Memory at e4000000 (32-bit, non-prefetchable) [size=1M]
0000:00:00.1 RAM memory: Transmeta Corporation SDRAM controller
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: fast devsel
0000:00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: fast devsel
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at b000 [size=16]
Capabilities: [c0] Power Management version 2
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Flags: medium devsel, IRQ 9
Capabilities: [68] Power Management version 2
0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50)
Subsystem: VIA Technologies, Inc. VT82C686 AC97 Audio Controller
Flags: medium devsel, IRQ 12
I/O ports at bc00 [size=256]
I/O ports at c000 [size=4]
I/O ports at c400 [size=4]
Capabilities: [c0] Power Management version 2
0000:00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at c800 [size=256]
Memory at e410a000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:00:0b.0 CardBus bridge: Texas Instruments PCI1420
Subsystem: Unknown device 3412:7856
Flags: bus master, medium devsel, latency 168, IRQ 5
Memory at e4100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: e4101000-e4102000 (prefetchable)
Memory window 1: e4103000-e4104000
I/O window 0: 0000cc00-0000d003
I/O window 1: 0000d400-0000d803
16-bit legacy interface ports at 0001
0000:00:0b.1 CardBus bridge: Texas Instruments PCI1420
Subsystem: Unknown device 3412:7856
Flags: bus master, medium devsel, latency 168, IRQ 5
Memory at e4105000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: e4106000-e4107000 (prefetchable)
Memory window 1: e4108000-e4109000
I/O window 0: 0000dc00-0000e003
I/O window 1: 0000e400-0000e803
16-bit legacy interface ports at 0001
0000:00:0c.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev c1) (prog-if 00 [VGA])
Subsystem: Silicon Motion, Inc. SM720 Lynx3DM
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 10
Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [40] Power Management version 1
0000:00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at ec00 [size=256]
Memory at e410b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
***lspci -tv
-[00]-+-00.0 Transmeta Corporation LongRun Northbridge
+-00.1 Transmeta Corporation SDRAM controller
+-00.2 Transmeta Corporation BIOS scratchpad
+-07.0 VIA Technologies, Inc. VT82C686 [Apollo Super South]
+-07.1 VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE
+-07.2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
+-07.3 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
+-07.4 VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
+-07.5 VIA Technologies, Inc. VT82C686 AC97 Audio Controller
+-08.0 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
+-0b.0 Texas Instruments PCI1420
+-0b.1 Texas Instruments PCI1420
+-0c.0 Silicon Motion, Inc. SM720 Lynx3DM
\-0d.0 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
***cardctl status
Socket 0:
5V 16-bit PC Card
function 0: [ready], [bat low]
Socket 1:
no card
***cat /proc/interrupts
CPU0
0: 150615 XT-PIC timer
1: 292 XT-PIC i8042
2: 0 XT-PIC cascade
5: 0 XT-PIC uhci_hcd, uhci_hcd
7: 0 XT-PIC parport0
9: 0 XT-PIC acpi
10: 168 XT-PIC eth0
12: 0 XT-PIC via82cxxx
15: 37036 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
***lsmod | grep yenta
yenta_socket 20616 3
rsrc_nonstatic 9856 1 yenta_socket
pcmcia_core 44848 4 airo_cs,pcmcia,yenta_socket,rsrc_nonstatic
***lsmod | grep airo
airo_cs 6788 1
airo 64160 1 airo_cs
pcmcia 23432 5 airo_cs
pcmcia_core 44848 4 airo_cs,pcmcia,yenta_socket,rsrc_nonstatic
***dmesg
Linux version 2.6.11-1-386 (dilinger@mouth) (gcc version 3.3.6 (Debian 1:3.3.6-5)) #1 Fri May 20 06:15:52 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b000 (usable)
BIOS-e820: 000000000009b000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001eff0000 (usable)
BIOS-e820: 000000001eff0000 - 000000001eff3000 (ACPI NVS)
BIOS-e820: 000000001eff3000 - 000000001f000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
495MB LOWMEM available.
On node 0 totalpages: 126960
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 122864 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 ARBOR ) @ 0x000f64e0
ACPI: RSDT (v001 ARBOR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1eff3000
ACPI: FADT (v001 ARBOR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1eff3040
ACPI: DSDT (v001 ARBOR AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 1f000000 (gap: 1f000000:e0ff0000)
Built 1 zonelists
Kernel command line: root=/dev/hdc1 ro
__iounmap: bad address c00fffd9
No local APIC present or hardware disabled
mapped APIC to ffffd000 (013e2000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 800.262 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 495944k/507840k available (1387k kernel code, 11204k reserved, 757k data, 220k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1576.96 BogoMIPS (lpj=788480)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0084893f 0081813f 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0084893f 0081813f 000000ce 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 512K (128 bytes/line)
CPU: Processor revision 1.4.1.0, 800 MHz
CPU: Code Morphing Software revision 4.3.3-9-510
CPU: 20020910 22:28 official release 4.3.3#5
CPU serial number disabled.
CPU: After all inits, caps: 0080893f 0081813f 000000ce 00000000 00000000 00000000 00000000
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 stepping 03
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: setting ELCR to 0200 (from 1e20)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4228k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfafe0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [email protected]
** so I can fix the driver.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([email protected])
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Disabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
PCI0 USB0 USB1 UAR1 UAR2 LPT1
ACPI: (supports S0 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4228KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.10 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: SAMSUNG CF/ATA, CFA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hdc: max request size: 128KiB
hdc: 2041200 sectors (1045 MB) w/0KiB Cache, CHS=2025/16/63
hdc: cache flushes not supported
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
/dev/ide/host0/bus1/target0/lun0: p1 p2 < p5 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 82112k swap on /dev/hdc5. Priority:-1 extents:1
EXT3 FS on hdc1, internal journal
Generic RTC Driver v1.07
Capability LSM initialized
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:00:0b.0 [3412:7856]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0b.0, mfunc 0x00001c02, devctl 0x62
Yenta TI: socket 0000:00:0b.0 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:0b.0 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0000, PCI irq 0
Socket status: 30000010
ACPI: PCI interrupt 0000:00:0b.1[A] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:00:0b.1 [3412:7856]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0b.1, mfunc 0x00001c02, devctl 0x62
Yenta TI: socket 0000:00:0b.1 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:0b.1 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0000, PCI irq 0
Socket status: 30000006
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xc800, 00:05:b7:02:8d:fb, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11
eth1: RealTek RTL8139 at 0xec00, 00:05:b7:02:53:be, IRQ 11
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 5, io base 0xb400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:07.3[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:07.3: irq 5, io base 0xb800
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Linux agpgart interface v0.100 (c) Dave Jones
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI interrupt 0000:00:07.5[C] -> GSI 12 (level, low) -> IRQ 12
PCI: Setting latency timer of device 0000:00:07.5 to 64
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
via82cxxx: board #1 at 0xBC00, IRQ 12
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
input: PC Speaker
NET: Registered protocol family 17
eth0: link down
cs: IO port probe 0x100-0x4ff: excluding 0x1f0-0x1f7 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x1f0-0x1f7 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
airo: Probing for PCI adapters
airo: Finished probing for PCI adapters
0.0: RequestIRQ: Resource in use
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e60a0(lo)
IPv6 over IPv4 tunneling driver
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
***uname -a
Linux pc104-1 2.6.11-1-386 #1 Fri May 20 06:15:52 UTC 2005 i686 GNU/Linux
***lspci -v
0000:00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 03)
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: bus master, medium devsel, latency 32
Memory at e4000000 (32-bit, non-prefetchable) [size=1M]
0000:00:00.1 RAM memory: Transmeta Corporation SDRAM controller
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: fast devsel
0000:00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
Subsystem: Transmeta Corporation: Unknown device 0295
Flags: fast devsel
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at b000 [size=16]
Capabilities: [c0] Power Management version 2
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
0000:00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Flags: medium devsel, IRQ 9
Capabilities: [68] Power Management version 2
0000:00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50)
Subsystem: VIA Technologies, Inc. VT82C686 AC97 Audio Controller
Flags: medium devsel, IRQ 12
I/O ports at bc00 [size=256]
I/O ports at c000 [size=4]
I/O ports at c400 [size=4]
Capabilities: [c0] Power Management version 2
0000:00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at c800 [size=256]
Memory at e410a000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:00:0b.0 CardBus bridge: Texas Instruments PCI1420
Subsystem: Unknown device 3412:7856
Flags: bus master, medium devsel, latency 168, IRQ 5
Memory at e4100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: e4101000-e4102000 (prefetchable)
Memory window 1: e4103000-e4104000
I/O window 0: 0000cc00-0000d003
I/O window 1: 0000d400-0000d803
16-bit legacy interface ports at 0001
0000:00:0b.1 CardBus bridge: Texas Instruments PCI1420
Subsystem: Unknown device 3412:7856
Flags: bus master, medium devsel, latency 168, IRQ 5
Memory at e4105000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: e4106000-e4107000 (prefetchable)
Memory window 1: e4108000-e4109000
I/O window 0: 0000dc00-0000e003
I/O window 1: 0000e400-0000e803
16-bit legacy interface ports at 0001
0000:00:0c.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev c1) (prog-if 00 [VGA])
Subsystem: Silicon Motion, Inc. SM720 Lynx3DM
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 10
Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [40] Power Management version 1
0000:00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at ec00 [size=256]
Memory at e410b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
***lspci -tv
-[00]-+-00.0 Transmeta Corporation LongRun Northbridge
+-00.1 Transmeta Corporation SDRAM controller
+-00.2 Transmeta Corporation BIOS scratchpad
+-07.0 VIA Technologies, Inc. VT82C686 [Apollo Super South]
+-07.1 VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE
+-07.2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
+-07.3 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
+-07.4 VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
+-07.5 VIA Technologies, Inc. VT82C686 AC97 Audio Controller
+-08.0 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
+-0b.0 Texas Instruments PCI1420
+-0b.1 Texas Instruments PCI1420
+-0c.0 Silicon Motion, Inc. SM720 Lynx3DM
\-0d.0 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
***cardctl status
Socket 0:
5V 16-bit PC Card
function 0: [ready], [bat low]
Socket 1:
no card
***cat /proc/interrupts
CPU0
0: 142848 XT-PIC timer
1: 50 XT-PIC i8042
2: 0 XT-PIC cascade
5: 0 XT-PIC uhci_hcd, uhci_hcd
7: 0 XT-PIC parport0
9: 0 XT-PIC acpi
12: 0 XT-PIC via82cxxx
15: 34018 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 0
MIS: 0
***lsmod | grep yenta
yenta_socket 20616 3
rsrc_nonstatic 9856 1 yenta_socket
pcmcia_core 44848 4 airo_cs,pcmcia,yenta_socket,rsrc_nonstatic
***lsmod | grep airo
airo_cs 6788 1
airo 64160 1 airo_cs
pcmcia 23432 5 airo_cs
pcmcia_core 44848 4 airo_cs,pcmcia,yenta_socket,rsrc_nonstatic
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
