On 6/8/05, Sonny Rao <[email protected]> wrote:
> Hi, I have an x335 here that I'm using on 2.6.11.11
>
> <from dmesg>
>
> Fusion MPT base driver 3.01.18
> Copyright (c) 1999-2004 LSI Logic Corporation
> ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 22 (level, low) -> IRQ 22
> mptbase: Initiating ioc0 bringup
> ioc0: 53C1030: Capabilities={Initiator}
> Fusion MPT SCSI Host driver 3.01.18
> scsi0 : ioc0: LSI53C1030, FwRev=01000e00h, Ports=1, MaxQ=222, IRQ=22
> Vendor: IBM-ESXS Model: MAS3367NC FN Rev: C901
> Type: Direct-Access ANSI SCSI revision: 03
> SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
> SCSI device sda: drive cache: write through
> SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
> SCSI device sda: drive cache: write through
> /dev/scsi/host0/bus0/target0/lun0: p1 p2
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Vendor: IBM-ESXS Model: MAS3367NC FN Rev: C901
> Type: Direct-Access ANSI SCSI revision: 03
> SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
> SCSI device sdb: drive cache: write through
> SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
> SCSI device sdb: drive cache: write through
> /dev/scsi/host0/bus0/target1/lun0: unknown partition table
> Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
> Vendor: IBM Model: 25P3495a S320 1 Rev: 1
> Type: Processor ANSI SCSI revision: 02
>
> Drive is a 15k 36GB disk:
>
> hdparm -t /dev/sda
>
> /dev/sda:
> Timing buffered disk reads: 226 MB in 3.01 seconds = 75.07 MB/sec
>
> So I'm not seeing that problem, does your dmesg output from the driver
> pretty much match what I have?
>
> Sonny
>
Our is a 10K drive - this is my dmesg output (from 2.6.12-rc5) - only
difference I can see is the ANSI SCSI revision (I have never
investigated the SCSI subsystem much in the kernel so how does one
interpreted the ANSI SCSI revision number ?).
Fusion MPT base driver 3.01.20
Copyright (c) 1999-2004 LSI Logic Corporation
ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 22 (level, low) -> IRQ 169
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator}
Fusion MPT SCSI Host driver 3.01.20
scsi0 : ioc0: LSI53C1030, FwRev=01032715h, Ports=1, MaxQ=222, IRQ=169
Vendor: IBM-ESXS Model: CBR036C31210ESFN Rev: DFQ8
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: IBM Model: 25P3495a S320 1 Rev: 1
Type: Processor ANSI SCSI revision: 02
Fusion MPT misc device (ioctl) driver 3.01.20
I have tried switching the 335 for another one but the performance is
till very low so I am quite sure that it is not a hardware problem.
Also compiling the driver as a module does not make any difference.
Regards.
Lars Roland
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]