On Mon, Jun 06, 2005 at 01:17:36PM -0500, James Bottomley wrote:
> Well, OK, three things spring to mind.
Thank for those three ideas :)
> 1. Try the attached patch, just in case it's a perpetual timer reset
> issue.
I put the log of the boot : not a success.
I hope the previous repport were right : ptelnet on my palm seems to
put the log in a strange order...
> 2. You should be able to boot if you set the device speed to 10MHz in
> the adaptec bios (since we should read the bios values for setting the
> speed)
I have set all device to 10 Mhz (for that controller) in the BIOS, but I
still can't boot.
> 3. when the hang occurs, can you get an alt-sysrq-p to show the current
> process on CPU?
MagicSysRq don't seems to work at this stage.
---
Bootdata ok (command line is root=/dev/sdc2 parport=auto video=vesafb:mtrr,ywrap,1024x800-16@75 vga=0xF07 console=ttyS0)
Linux version 2.6.12-rc5 (root@gregoire) (gcc version 3.4.3 20041125 (Gentoo Linux 3.4.3-r1, ssp-3.4.3-0, pie-8.7.7)) #4 Mon Jun 6 20:29:04 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/sdc2 parport=auto video=vesafb:mtrr,ywrap,1024x800-16@75 vga=0xF07 console=ttyS0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2000.089 MHz processor.
time.c: Using PIT/TSC based timekeeping.
Console: colour VGA+ 80x60
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 1025304k/1048512k available (3138k kernel code, 22512k reserved, 1306k data, 160k init)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
NTFS driver 2.1.22 [Flags: R/O].
EFS: 1.0a - http://aeschi.ch.eu.org/efs/
SGI XFS with large block/inode numbers, no debug enabled
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport0: PC-style at 0x378 [PCSPP(,...)]
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
r8169: NAPI enabled
eth0: RTL8169 at 0xffffc20000002b00, 00:0c:76:bd:22:23, IRQ 16
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L120AVVA07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI Floppy, ATAPI FLOPPY drive
hdd: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdd: set_drive_speed_status: error=0x04 { AbortedCommand }
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 16X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdd: No disk in drive
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
target0:0:0: Beginning Domain Validation
WIDTH IS 1
(scsi0:A:0): 6.600MB/s transfers (16bit)
target0:0:0: Domain Validation skipping write tests
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
target0:0:0: Ending Domain Validation
Vendor: SEAGATE Model: ST336706LW Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:15:0: Tagged Queuing enabled. Depth 253
target0:0:15: Beginning Domain Validation
WIDTH IS 1
(scsi0:A:15): 6.600MB/s transfers (16bit)
(scsi0:A:15): 80.000MB/s transfers (40.000MHz, offset 63, 16bit)
target0:0:15: Ending Domain Validation
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
scsi1:0:0:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x24 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x3, SINDEX = 0x20, DINDEX = 0xc0, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x1]
SCSISEQ[0x1a] SBLKCTL[0x0] SCSIRATE[0x0] SEQCTL[0x10]
SEQ_FLAGS[0xc0] SSTAT0[0x5] SSTAT1[0x0] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4] SXFRCTL0[0x80]
DFCNTRL[0x4] DFSTATUS[0x6d]
STACK: 0x0 0x0 0x192 0x17
SCB count = 4
Kernel NEXTQSCB = 2
Card NEXTQSCB = 2
QINFIFO entries:
Waiting Queue entries: 0:3
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x50] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0x3]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x50] SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(0): 3
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x3, SINDEX = 0x20, DINDEX = 0xc0, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x1]
SCSISEQ[0x1a] SBLKCTL[0x0] SCSIRATE[0x0] SEQCTL[0x10]
SEQ_FLAGS[0xc0] SSTAT0[0x5] SSTAT1[0x0] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4] SXFRCTL0[0x80]
DFCNTRL[0x4] DFSTATUS[0x6d]
STACK: 0x0 0x0 0x192 0x17
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 2
QINFIFO entries: 2
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
2 SCB_CONTROL[0x50] SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(0): 2
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue a TARGET RESET message
CDB: 0x12 0x0 0x0 0x0 0x24 0x0
scsi1:0:0:0: Command not found
aic7xxx_dev_reset returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x3, SINDEX = 0x20, DINDEX = 0xc0, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x1]
SCSISEQ[0x1a] SBLKCTL[0x0] SCSIRATE[0x0] SEQCTL[0x10]
SEQ_FLAGS[0xc0] SSTAT0[0x5] SSTAT1[0x0] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4] SXFRCTL0[0x80]
DFCNTRL[0x4] DFSTATUS[0x6d]
STACK: 0x0 0x0 0x192 0x17
SCB count = 4
Kernel NEXTQSCB = 2
Card NEXTQSCB = 3
QINFIFO entries: 3
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x50] SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(0): 3
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi: Device offlined - not ready after error recovery: host 1 channel 0 id 0 lun 0
Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R08
Type: CD-ROM ANSI SCSI revision: 02
target1:0:1: Beginning Domain Validation
target1:0:1: Domain Validation skipping write tests
(scsi1:A:1): 20.000MB/s transfers (20.000MHz, offset 15)
scsi1:0:1:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x60 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Data-in phase, at SEQADDR 0x7b
Card was paused
ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
HCNT = 0x60 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0xf] SEQCTL[0x10]
SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0xa0]
DFCNTRL[0x38] DFSTATUS[0x40]
STACK: 0x0 0x162 0x192 0x6e
SCB count = 4
Kernel NEXTQSCB = 2
Card NEXTQSCB = 2
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x48] SCB_SCSIID[0x17] SCB_LUN[0x0] SCB_TAG[0x3]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
3 SCB_CONTROL[0x48] SCB_SCSIID[0x17] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(1): 3
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:1:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 0x2003
scsi1:0:1:0: Attempting to queue a TARGET RESET message
CDB: 0x12 0x0 0x0 0x0 0x60 0x0
aic7xxx_dev_reset returns 0x2003
Recovery SCB completes
scsi1:0:1:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State in Data-in phase, at SEQADDR 0x7b
Card was paused
ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
HCNT = 0x20 SCBPTR = 0x0
SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0xf] SEQCTL[0x10]
SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0x80]
DFCNTRL[0x38] DFSTATUS[0x20]
STACK: 0x0 0x162 0x192 0x6e
SCB count = 4
Kernel NEXTQSCB = 3
Card NEXTQSCB = 3
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x8] SCB_SCSIID[0x17] SCB_LUN[0x0] SCB_TAG[0x2]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
2 SCB_CONTROL[0x8] SCB_SCSIID[0x17] SCB_LUN[0x0]
Kernel Free SCB list: 1 0
Untagged Q(1): 2
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:0:1:0: Device is active, asserting ATN
Recovery code sleeping
Recovery code awake
Timer Expired
aic7xxx_abort returns 0x2003
scsi: Device offlined - not ready after error recovery: host 1 channel 0 id 1 lun 0
target1:0:1: Domain Validation detected failure, dropping back
---
--
Grégoire Favre
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
