Hi,
Update the patch, it's against bleeding edge git (applies to 2.6.12-rc5
as well). Changes:
- (libata) Change to SCSI change_queue_depth API, kill current hack.
- (ahci) Move SActive bit set to ahci_qc_issue() where it belongs.
- (ahci) Check fatal irq mask for NCQ.
- (libata) Check IDENTIFICATION page for NCQ support
- (libata) Remove legacy code from ata_read_log_page()
- (libata) Split ATA_MAX_QUEUE into ATA_MAX_QUEUE and ATA_MAX_CMDS.
Index: drivers/scsi/ahci.c
===================================================================
--- 3ac9a34948049bff79a2b2ce49c0a3c84e35a748/drivers/scsi/ahci.c (mode:100644)
+++ uncommitted/drivers/scsi/ahci.c (mode:100644)
@@ -19,8 +19,8 @@
* If you do not delete the provisions above, a recipient may use your
* version of this file under either the OSL or the GPL.
*
- * Version 1.0 of the AHCI specification:
- * http://www.intel.com/technology/serialata/pdf/rev1_0.pdf
+ * Version 1.1 of the AHCI specification:
+ * http://www.intel.com/technology/serialata/pdf/rev1_1.pdf
*
*/
@@ -46,10 +46,13 @@
AHCI_MAX_SG = 168, /* hardware max is 64K */
AHCI_DMA_BOUNDARY = 0xffffffff,
AHCI_USE_CLUSTERING = 0,
- AHCI_CMD_SLOT_SZ = 32 * 32,
- AHCI_RX_FIS_SZ = 256,
+ AHCI_MAX_CMDS = 32,
+ AHCI_CMD_SZ = 32,
AHCI_CMD_TBL_HDR = 0x80,
- AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR + (AHCI_MAX_SG * 16),
+ AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ,
+ AHCI_RX_FIS_SZ = 256,
+ AHCI_CMD_TOTAL = AHCI_CMD_TBL_HDR + (AHCI_MAX_SG * 16),
+ AHCI_CMD_TBL_SZ = AHCI_MAX_CMDS * AHCI_CMD_TOTAL,
AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_SZ +
AHCI_RX_FIS_SZ,
AHCI_IRQ_ON_SG = (1 << 31),
@@ -57,6 +60,7 @@
AHCI_CMD_WRITE = (1 << 6),
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
+ RX_FIS_SDB_REG = 0x58, /* offset of SDB Register FIS data */
board_ahci = 0,
@@ -74,6 +78,7 @@
/* HOST_CAP bits */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
+ HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
@@ -161,9 +166,9 @@
dma_addr_t cmd_slot_dma;
void *cmd_tbl;
dma_addr_t cmd_tbl_dma;
- struct ahci_sg *cmd_tbl_sg;
void *rx_fis;
dma_addr_t rx_fis_dma;
+ u32 sactive;
};
static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg);
@@ -181,7 +186,7 @@
static void ahci_qc_prep(struct ata_queued_cmd *qc);
static u8 ahci_check_status(struct ata_port *ap);
static u8 ahci_check_err(struct ata_port *ap);
-static inline int ahci_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc);
+static inline int ahci_host_intr(struct ata_port *ap);
static Scsi_Host_Template ahci_sht = {
.module = THIS_MODULE,
@@ -189,7 +194,8 @@
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.eh_strategy_handler = ata_scsi_error,
- .can_queue = ATA_DEF_QUEUE,
+ .change_queue_depth = ata_scsi_change_queue_depth,
+ .can_queue = ATA_MAX_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = AHCI_MAX_SG,
.max_sectors = ATA_MAX_SECTORS,
@@ -200,7 +206,7 @@
.dma_boundary = AHCI_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
- .ordered_flush = 1,
+ .ordered_flush = 0, /* conflicts with NCQ for now */
};
static struct ata_port_operations ahci_ops = {
@@ -339,14 +345,11 @@
mem_dma += AHCI_RX_FIS_SZ;
/*
- * Third item: data area for storing a single command
- * and its scatter-gather table
+ * Third item: data area for storing commands and their sg tables
*/
pp->cmd_tbl = mem;
pp->cmd_tbl_dma = mem_dma;
- pp->cmd_tbl_sg = mem + AHCI_CMD_TBL_HDR;
-
ap->private_data = pp;
if (hpriv->cap & HOST_CAP_64)
@@ -478,9 +481,10 @@
ata_tf_from_fis(d2h_fis, tf);
}
-static void ahci_fill_sg(struct ata_queued_cmd *qc)
+static void ahci_fill_sg(struct ata_queued_cmd *qc, int offset)
{
struct ahci_port_priv *pp = qc->ap->private_data;
+ struct ahci_sg *cmd_tbl_sg;
unsigned int i;
VPRINTK("ENTER\n");
@@ -488,6 +492,7 @@
/*
* Next, the S/G list.
*/
+ cmd_tbl_sg = pp->cmd_tbl + offset + AHCI_CMD_TBL_HDR;
for (i = 0; i < qc->n_elem; i++) {
u32 sg_len;
dma_addr_t addr;
@@ -495,21 +500,22 @@
addr = sg_dma_address(&qc->sg[i]);
sg_len = sg_dma_len(&qc->sg[i]);
- pp->cmd_tbl_sg[i].addr = cpu_to_le32(addr & 0xffffffff);
- pp->cmd_tbl_sg[i].addr_hi = cpu_to_le32((addr >> 16) >> 16);
- pp->cmd_tbl_sg[i].flags_size = cpu_to_le32(sg_len - 1);
+ cmd_tbl_sg[i].addr = cpu_to_le32(addr & 0xffffffff);
+ cmd_tbl_sg[i].addr_hi = cpu_to_le32((addr >> 16) >> 16);
+ cmd_tbl_sg[i].flags_size = cpu_to_le32(sg_len - 1);
}
}
static void ahci_qc_prep(struct ata_queued_cmd *qc)
{
struct ahci_port_priv *pp = qc->ap->private_data;
- u32 opts;
const u32 cmd_fis_len = 5; /* five dwords */
+ dma_addr_t cmd_tbl_dma;
+ u32 opts;
+ int offset;
/*
- * Fill in command slot information (currently only one slot,
- * slot 0, is currently since we don't do queueing)
+ * Fill in command slot information
*/
opts = (qc->n_elem << 16) | cmd_fis_len;
@@ -528,21 +534,28 @@
break;
}
- pp->cmd_slot[0].opts = cpu_to_le32(opts);
- pp->cmd_slot[0].status = 0;
- pp->cmd_slot[0].tbl_addr = cpu_to_le32(pp->cmd_tbl_dma & 0xffffffff);
- pp->cmd_slot[0].tbl_addr_hi = cpu_to_le32((pp->cmd_tbl_dma >> 16) >> 16);
+ /*
+ * the tag determines the offset into the allocated cmd table
+ */
+ offset = qc->tag * AHCI_CMD_TOTAL;
+
+ cmd_tbl_dma = pp->cmd_tbl_dma + offset;
+
+ pp->cmd_slot[qc->tag].opts = cpu_to_le32(opts);
+ pp->cmd_slot[qc->tag].status = 0;
+ pp->cmd_slot[qc->tag].tbl_addr = cpu_to_le32(cmd_tbl_dma & 0xffffffff);
+ pp->cmd_slot[qc->tag].tbl_addr_hi = cpu_to_le32((cmd_tbl_dma >> 16) >> 16);
/*
* Fill in command table information. First, the header,
* a SATA Register - Host to Device command FIS.
*/
- ata_tf_to_fis(&qc->tf, pp->cmd_tbl, 0);
+ ata_tf_to_fis(&qc->tf, pp->cmd_tbl + offset, 0);
if (!(qc->flags & ATA_QCFLAG_DMAMAP))
return;
- ahci_fill_sg(qc);
+ ahci_fill_sg(qc, offset);
}
static void ahci_intr_error(struct ata_port *ap, u32 irq_stat)
@@ -593,7 +606,54 @@
printk(KERN_WARNING "ata%u: error occurred, port reset\n", ap->id);
}
-static void ahci_eng_timeout(struct ata_port *ap)
+static void dump_log_page(unsigned char *p)
+{
+ int i;
+
+ printk("LOG 0x10: nq=%d, tag=%d\n", p[0] >> 7, p[0] & 0x1f);
+
+ for (i = 2; i < 14; i++)
+ printk("%d:%d ", i, p[i]);
+
+ printk("\n");
+}
+
+static void ahci_host_ncq_intr_err(struct ata_port *ap)
+{
+ void *mmio = ap->host_set->mmio_base;
+ void *port_mmio = ahci_port_base(mmio, ap->port_no);
+ char *buffer;
+
+ printk(KERN_ERR "ata%u: ncq interrupt error\n", ap->id);
+
+ ahci_intr_error(ap, readl(port_mmio + PORT_IRQ_STAT));
+
+ buffer = kmalloc(512, GFP_KERNEL);
+ if (!buffer) {
+ printk(KERN_ERR "ata%u: unable to allocate memory for error\n", ap->id);
+ return;
+ }
+
+ if (ata_read_log_page(ap, 0, 0x10, buffer, 1)) {
+ printk(KERN_ERR "ata%u: unable to read log page\n", ap->id);
+ goto out;
+ }
+
+ dump_log_page(buffer);
+
+out:
+ kfree(buffer);
+}
+
+/*
+ * TODO: needs to use READ_LOG_EXT/page=10h to retrieve error information
+ */
+static void ahci_ncq_timeout(struct ata_port *ap)
+{
+ ahci_host_ncq_intr_err(ap);
+}
+
+static void ahci_nonncq_timeout(struct ata_port *ap)
{
void *mmio = ap->host_set->mmio_base;
void *port_mmio = ahci_port_base(mmio, ap->port_no);
@@ -617,13 +677,65 @@
qc->scsidone = scsi_finish_command;
ata_qc_complete(qc, ATA_ERR);
}
+}
+
+static void ahci_eng_timeout(struct ata_port *ap)
+{
+ if (ap->ncq_depth)
+ ahci_ncq_timeout(ap);
+ else
+ ahci_nonncq_timeout(ap);
+}
+
+static inline void ahci_host_ncq_intr(struct ata_port *ap, u32 status)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ void *mmio = ap->host_set->mmio_base;
+ void *port_mmio = ahci_port_base(mmio, ap->port_no);
+ u32 tags, sactive;
+
+ if (status & PORT_IRQ_D2H_REG_FIS) {
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+
+ /*
+ * pre-BSY clear error, let timeout error handling take care
+ * of it when it kicks in
+ */
+ if (d2h_fis[2] & ATA_ERR)
+ return;
+ } else if (status & PORT_IRQ_SDB_FIS) {
+ u8 *sdb_fis = pp->rx_fis + RX_FIS_SDB_REG;
+
+ if (sdb_fis[1] & ATA_ERR)
+ return;
+ }
+
+ /*
+ * SActive will have the bits cleared for completed commands
+ */
+ sactive = readl(port_mmio + PORT_SCR_ACT);
+ tags = pp->sactive & ~sactive;
+
+ while (tags) {
+ struct ata_queued_cmd *qc;
+ int tag = ffs(tags) - 1;
+
+ tags &= ~(1 << tag);
+ qc = ata_qc_from_tag(ap, tag);
+ if (qc)
+ ata_qc_complete(qc, 0);
+ else
+ printk(KERN_ERR "ahci: missing tag %d\n", tag);
+ }
+ pp->sactive = sactive;
}
-static inline int ahci_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
+static inline int ahci_host_intr(struct ata_port *ap)
{
void *mmio = ap->host_set->mmio_base;
void *port_mmio = ahci_port_base(mmio, ap->port_no);
+ struct ata_queued_cmd *qc;
u32 status, serr, ci;
serr = readl(port_mmio + PORT_SCR_ERR);
@@ -632,18 +744,27 @@
status = readl(port_mmio + PORT_IRQ_STAT);
writel(status, port_mmio + PORT_IRQ_STAT);
- ci = readl(port_mmio + PORT_CMD_ISSUE);
- if (likely((ci & 0x1) == 0)) {
- if (qc) {
- ata_qc_complete(qc, 0);
- qc = NULL;
+ if (ap->ncq_depth) {
+ if (serr || (status & PORT_IRQ_FATAL))
+ ahci_host_ncq_intr_err(ap);
+ else
+ ahci_host_ncq_intr(ap, status);
+ } else {
+ ci = readl(port_mmio + PORT_CMD_ISSUE);
+ if (likely((ci & 0x1) == 0)) {
+ qc = ata_qc_from_tag(ap, ap->active_tag);
+ if (qc) {
+ ata_qc_complete(qc, 0);
+ qc = NULL;
+ }
}
- }
- if (status & PORT_IRQ_FATAL) {
- ahci_intr_error(ap, status);
- if (qc)
- ata_qc_complete(qc, ATA_ERR);
+ if (status & PORT_IRQ_FATAL) {
+ ahci_intr_error(ap, status);
+ qc = ata_qc_from_tag(ap, ap->active_tag);
+ if (qc)
+ ata_qc_complete(qc, ATA_ERR);
+ }
}
return 1;
@@ -683,9 +804,7 @@
ap = host_set->ports[i];
tmp = irq_stat & (1 << i);
if (tmp && ap) {
- struct ata_queued_cmd *qc;
- qc = ata_qc_from_tag(ap, ap->active_tag);
- if (ahci_host_intr(ap, qc))
+ if (ahci_host_intr(ap))
irq_ack |= (1 << i);
}
}
@@ -705,12 +824,17 @@
static int ahci_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
+ struct ahci_port_priv *pp = qc->ap->private_data;
void *port_mmio = (void *) ap->ioaddr.cmd_addr;
- writel(1, port_mmio + PORT_SCR_ACT);
- readl(port_mmio + PORT_SCR_ACT); /* flush */
+ if (qc->flags & ATA_QCFLAG_NCQ) {
+ pp->sactive |= (1 << qc->tag);
+
+ writel(1 << qc->tag, port_mmio + PORT_SCR_ACT);
+ readl(port_mmio + PORT_SCR_ACT); /* flush */
+ }
- writel(1, port_mmio + PORT_CMD_ISSUE);
+ writel(1 << qc->tag, port_mmio + PORT_CMD_ISSUE);
readl(port_mmio + PORT_CMD_ISSUE); /* flush */
return 0;
@@ -1027,6 +1151,9 @@
if (rc)
goto err_out_hpriv;
+ if (hpriv->cap & HOST_CAP_NCQ)
+ probe_ent->host_flags |= ATA_FLAG_NCQ;
+
ahci_print_info(probe_ent);
/* FIXME: check ata_device_add return value */
Index: drivers/scsi/libata-core.c
===================================================================
--- 3ac9a34948049bff79a2b2ce49c0a3c84e35a748/drivers/scsi/libata-core.c (mode:100644)
+++ uncommitted/drivers/scsi/libata-core.c (mode:100644)
@@ -519,7 +519,7 @@
* LOCKING:
* None.
*/
-static int ata_prot_to_cmd(int protocol, int lba48)
+static int ata_prot_to_cmd(int protocol, int lba48, int ncq)
{
int rcmd = 0, wcmd = 0;
@@ -535,7 +535,10 @@
break;
case ATA_PROT_DMA:
- if (lba48) {
+ if (ncq) {
+ rcmd = ATA_CMD_FPDMA_READ;
+ wcmd = ATA_CMD_FPDMA_WRITE;
+ } else if (lba48) {
rcmd = ATA_CMD_READ_EXT;
wcmd = ATA_CMD_WRITE_EXT;
} else {
@@ -568,6 +571,7 @@
{
int pio = (dev->flags & ATA_DFLAG_PIO);
int lba48 = (dev->flags & ATA_DFLAG_LBA48);
+ int ncq = (dev->flags & ATA_DFLAG_NCQ);
int proto, cmd;
if (pio)
@@ -575,7 +579,7 @@
else
proto = dev->xfer_protocol = ATA_PROT_DMA;
- cmd = ata_prot_to_cmd(proto, lba48);
+ cmd = ata_prot_to_cmd(proto, lba48, ncq);
if (cmd < 0)
BUG();
@@ -1139,6 +1143,10 @@
goto err_out_nosup;
}
+ /* host NCQ is required as well as device support */
+ if ((ap->flags & ATA_FLAG_NCQ) && ata_id_has_ncq(dev->id))
+ dev->flags |= ATA_DFLAG_NCQ;
+
if (ata_id_has_lba48(dev->id)) {
dev->flags |= ATA_DFLAG_LBA48;
dev->n_sectors = ata_id_u64(dev->id, 100);
@@ -1149,11 +1157,12 @@
ap->host->max_cmd_len = 16;
/* print device info to dmesg */
- printk(KERN_INFO "ata%u: dev %u ATA, max %s, %Lu sectors:%s\n",
+ printk(KERN_INFO "ata%u: dev %u ATA, max %s, %Lu sectors:%s%s\n",
ap->id, device,
ata_mode_string(xfer_modes),
(unsigned long long)dev->n_sectors,
- dev->flags & ATA_DFLAG_LBA48 ? " lba48" : "");
+ dev->flags & ATA_DFLAG_LBA48 ? " lba48" : "",
+ dev->flags & ATA_DFLAG_NCQ ? " ncq" : "");
}
/* ATAPI-specific feature tests */
@@ -1187,6 +1196,66 @@
}
/**
+ * ata_read_log_page - read a specific log page
+ * @ap: port on which device we wish to probe resides
+ * @device: device bus address, starting at zero
+ * @page: page to read
+ * @buffer: where to store the read data
+ * @sectors: how much data to read
+ *
+ * After reading the device information page, we use several
+ * bits of information from it to initialize data structures
+ * that will be used during the lifetime of the ata_device.
+ * Other data from the info page is used to disqualify certain
+ * older ATA devices we do not wish to support.
+ *
+ * LOCKING:
+ * Grabs host_set lock.
+ */
+
+int ata_read_log_page(struct ata_port *ap, unsigned int device, char page,
+ char *buffer, unsigned int sectors)
+{
+ struct ata_device *dev = &ap->device[device];
+ DECLARE_COMPLETION(wait);
+ struct ata_queued_cmd *qc;
+ unsigned long flags;
+ int rc;
+
+ assert(dev->class == ATA_DEV_ATA);
+
+ qc = ata_qc_new_init(ap, dev);
+ BUG_ON(qc == NULL);
+
+ ata_sg_init_one(qc, buffer, sectors << 9);
+ qc->dma_dir = DMA_FROM_DEVICE;
+ qc->tf.protocol = ATA_PROT_PIO;
+ qc->nsect = sectors;
+
+ qc->tf.command = ATA_CMD_READ_LOG_EXT;
+ qc->tf.nsect = sectors;
+ qc->tf.hob_nsect = sectors >> 8;
+ qc->tf.lbal = page;
+
+ qc->waiting = &wait;
+ qc->complete_fn = ata_qc_complete_noop;
+
+ printk("RLP issue\n");
+ spin_lock_irqsave(&ap->host_set->lock, flags);
+ rc = ata_qc_issue(qc);
+ spin_unlock_irqrestore(&ap->host_set->lock, flags);
+ printk("RLP issue done\n");
+
+ if (rc)
+ return -EIO;
+
+ wait_for_completion(&wait);
+
+ printk("RLP wait done\n");
+ return 0;
+}
+
+/**
* ata_bus_probe - Reset and probe ATA bus
* @ap: Bus to probe
*
@@ -2699,7 +2768,7 @@
struct ata_queued_cmd *qc = NULL;
unsigned int i;
- for (i = 0; i < ATA_MAX_QUEUE; i++)
+ for (i = 0; i < ATA_MAX_CMDS; i++)
if (!test_and_set_bit(i, &ap->qactive)) {
qc = ata_qc_from_tag(ap, i);
break;
@@ -2754,6 +2823,16 @@
struct ata_port *ap = qc->ap;
unsigned int tag, do_clear = 0;
+ if (likely(qc->flags & ATA_QCFLAG_ACCOUNT)) {
+ if (qc->flags & ATA_QCFLAG_NCQ) {
+ assert(ap->ncq_depth);
+ ap->ncq_depth--;
+ } else {
+ assert(ap->depth);
+ ap->depth--;
+ }
+ }
+
qc->flags = 0;
tag = qc->tag;
if (likely(ata_tag_valid(tag))) {
@@ -2771,6 +2850,8 @@
if (likely(do_clear))
clear_bit(tag, &ap->qactive);
+ if (ap->cmd_waiters)
+ wake_up(&ap->cmd_wait_queue);
}
/**
@@ -2849,6 +2930,52 @@
/* never reached */
}
+/*
+ * NCQ and non-NCQ commands are mutually exclusive. So we have to deny a
+ * request to queue a non-NCQ command, if we have NCQ commands in flight (and
+ * vice versa).
+ */
+static inline int ata_qc_issue_ok(struct ata_port *ap,
+ struct ata_queued_cmd *qc, int waiting)
+{
+ /*
+ * if people are already waiting for a queue drain, don't allow a
+ * new 'lucky' queuer to get in there
+ */
+ if (ap->cmd_waiters > waiting)
+ return 0;
+ if (qc->flags & ATA_QCFLAG_NCQ)
+ return !ap->depth;
+
+ return !(ap->ncq_depth + ap->depth);
+}
+
+static void ata_qc_issue_wait(struct ata_port *ap, struct ata_queued_cmd *qc)
+{
+ DEFINE_WAIT(wait);
+
+ ap->cmd_waiters++;
+
+ do {
+ /*
+ * we rely on the FIFO order of the exclusive waitqueues
+ */
+ prepare_to_wait_exclusive(&ap->cmd_wait_queue, &wait,
+ TASK_UNINTERRUPTIBLE);
+
+ if (!ata_qc_issue_ok(ap, qc, 1)) {
+ spin_unlock_irq(&ap->host_set->lock);
+ schedule();
+ spin_lock_irq(&ap->host_set->lock);
+ }
+
+ finish_wait(&ap->cmd_wait_queue, &wait);
+
+ } while (!ata_qc_issue_ok(ap, qc, 1));
+
+ ap->cmd_waiters--;
+}
+
/**
* ata_qc_issue - issue taskfile to device
* @qc: command to issue to device
@@ -2868,6 +2995,21 @@
int ata_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
+ int rc = ATA_QC_ISSUE_FATAL;
+
+ /*
+ * see if we can queue one more command at this point in time, see
+ * comment at ata_qc_issue_ok(). NCQ commands typically originate from
+ * the SCSI layer, we can ask the mid layer to defer those commands
+ * similar to a QUEUE_FULL condition on a 'real' SCSI device
+ */
+ if (!ata_qc_issue_ok(ap, qc, 0)) {
+ if (qc->flags & ATA_QCFLAG_DEFER)
+ return ATA_QC_ISSUE_DEFER;
+
+ ata_qc_issue_wait(ap, qc);
+ assert(ata_qc_issue_ok(ap, qc, 0));
+ }
if (ata_should_dma_map(qc)) {
if (qc->flags & ATA_QCFLAG_SG) {
@@ -2884,12 +3026,24 @@
ap->ops->qc_prep(qc);
qc->ap->active_tag = qc->tag;
- qc->flags |= ATA_QCFLAG_ACTIVE;
+ qc->flags |= (ATA_QCFLAG_ACTIVE | ATA_QCFLAG_ACCOUNT);
+
+ rc = ap->ops->qc_issue(qc);
+ if (rc != ATA_QC_ISSUE_OK)
+ goto err_out;
- return ap->ops->qc_issue(qc);
+ if (qc->flags & ATA_QCFLAG_NCQ) {
+ assert(ap->ncq_depth < ATA_MAX_QUEUE)
+ ap->ncq_depth++;
+ } else {
+ assert(!ap->depth);
+ ap->depth++;
+ }
+ return ATA_QC_ISSUE_OK;
err_out:
- return -1;
+ ata_qc_free(qc);
+ return rc;
}
/**
@@ -2951,7 +3105,8 @@
default:
WARN_ON(1);
- return -1;
+ ata_qc_free(qc);
+ return ATA_QC_ISSUE_FATAL;
}
return 0;
@@ -3383,6 +3538,8 @@
ap->ops = ent->port_ops;
ap->cbl = ATA_CBL_NONE;
ap->active_tag = ATA_TAG_POISON;
+ init_waitqueue_head(&ap->cmd_wait_queue);
+ ap->cmd_waiters = 0;
ap->last_ctl = 0xFF;
INIT_WORK(&ap->packet_task, atapi_packet_task, ap);
@@ -4018,6 +4175,8 @@
EXPORT_SYMBOL_GPL(ata_dev_classify);
EXPORT_SYMBOL_GPL(ata_dev_id_string);
EXPORT_SYMBOL_GPL(ata_scsi_simulate);
+EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth);
+EXPORT_SYMBOL_GPL(ata_read_log_page);
#ifdef CONFIG_PCI
EXPORT_SYMBOL_GPL(pci_test_config_bits);
Index: drivers/scsi/libata-scsi.c
===================================================================
--- 3ac9a34948049bff79a2b2ce49c0a3c84e35a748/drivers/scsi/libata-scsi.c (mode:100644)
+++ uncommitted/drivers/scsi/libata-scsi.c (mode:100644)
@@ -336,6 +336,7 @@
if (sdev->id < ATA_MAX_DEVICES) {
struct ata_port *ap;
struct ata_device *dev;
+ int depth;
ap = (struct ata_port *) &sdev->host->hostdata[0];
dev = &ap->device[sdev->id];
@@ -353,6 +354,13 @@
*/
blk_queue_max_sectors(sdev->request_queue, 2048);
}
+
+ if (dev->flags & ATA_DFLAG_NCQ) {
+ int ddepth = ata_id_queue_depth(dev->id);
+
+ depth = min(sdev->host->can_queue, ddepth);
+ scsi_adjust_queue_depth(sdev, MSG_SIMPLE_TAG, depth);
+ }
}
return 0; /* scsi layer doesn't check return value, sigh */
@@ -537,6 +545,7 @@
{
struct ata_taskfile *tf = &qc->tf;
unsigned int lba48 = tf->flags & ATA_TFLAG_LBA48;
+ unsigned int ncq = qc->dev->flags & ATA_DFLAG_NCQ;
tf->flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
tf->protocol = qc->dev->xfer_protocol;
@@ -550,8 +559,18 @@
tf->flags |= ATA_TFLAG_WRITE;
}
+ if (ncq)
+ qc->flags |= ATA_QCFLAG_NCQ;
+
if (scsicmd[0] == READ_10 || scsicmd[0] == WRITE_10) {
- if (lba48) {
+ if (ncq) {
+ tf->hob_feature = scsicmd[7];
+ tf->feature = scsicmd[8];
+ tf->nsect = qc->tag << 3;
+ tf->hob_lbal = scsicmd[2];
+ qc->nsect = ((unsigned int)scsicmd[7] << 8) |
+ scsicmd[8];
+ } else if (lba48) {
tf->hob_nsect = scsicmd[7];
tf->hob_lbal = scsicmd[2];
@@ -569,7 +588,8 @@
qc->nsect = scsicmd[8];
}
- tf->nsect = scsicmd[8];
+ if (!ncq)
+ tf->nsect = scsicmd[8];
tf->lbal = scsicmd[5];
tf->lbam = scsicmd[4];
tf->lbah = scsicmd[3];
@@ -579,7 +599,14 @@
}
if (scsicmd[0] == READ_6 || scsicmd[0] == WRITE_6) {
- qc->nsect = tf->nsect = scsicmd[4];
+ qc->nsect = scsicmd[4];
+
+ if (ncq) {
+ tf->nsect = qc->tag << 3;
+ tf->feature = scsicmd[4];
+ } else
+ tf->nsect = scsicmd[4];
+
tf->lbal = scsicmd[3];
tf->lbam = scsicmd[2];
tf->lbah = scsicmd[1] & 0x1f; /* mask out reserved bits */
@@ -593,7 +620,16 @@
if (scsicmd[2] || scsicmd[3] || scsicmd[10] || scsicmd[11])
return 1;
- if (lba48) {
+ if (ncq) {
+ tf->hob_feature = scsicmd[13];
+ tf->feature = scsicmd[12];
+ tf->nsect = qc->tag << 3;
+ tf->hob_lbal = scsicmd[6];
+ tf->hob_lbam = scsicmd[5];
+ tf->hob_lbah = scsicmd[4];
+ qc->nsect = ((unsigned int)scsicmd[12] << 8) |
+ scsicmd[13];
+ } else if (lba48) {
tf->hob_nsect = scsicmd[12];
tf->hob_lbal = scsicmd[6];
tf->hob_lbam = scsicmd[5];
@@ -613,7 +649,8 @@
qc->nsect = scsicmd[13];
}
- tf->nsect = scsicmd[13];
+ if (!ncq)
+ tf->nsect = scsicmd[13];
tf->lbal = scsicmd[9];
tf->lbam = scsicmd[8];
tf->lbah = scsicmd[7];
@@ -666,6 +703,7 @@
{
struct ata_queued_cmd *qc;
u8 *scsicmd = cmd->cmnd;
+ int ret;
VPRINTK("ENTER\n");
@@ -696,9 +734,18 @@
if (xlat_func(qc, scsicmd))
goto err_out;
+ qc->flags |= ATA_QCFLAG_DEFER;
+
/* select device, send command to hardware */
- if (ata_qc_issue(qc))
+ ret = ata_qc_issue(qc);
+ if (ret == ATA_QC_ISSUE_FATAL)
goto err_out;
+ else if (ret == ATA_QC_ISSUE_DEFER) {
+ VPRINTK("DEFER\n");
+ ata_qc_free(qc);
+ cmd->result = (DID_OK << 16) | (QUEUE_FULL << 1);
+ done(cmd);
+ }
VPRINTK("EXIT\n");
return;
@@ -1594,3 +1641,22 @@
}
}
+int ata_scsi_change_queue_depth(struct scsi_device *sdev, int queue_depth)
+{
+ struct ata_port *ap;
+ struct ata_device *dev;
+ int max_depth;
+
+ if (sdev->id >= ATA_MAX_DEVICES)
+ return sdev->queue_depth;
+
+ ap = (struct ata_port *) &sdev->host->hostdata[0];
+ dev = &ap->device[sdev->id];
+
+ max_depth = min(sdev->host->can_queue, ata_id_queue_depth(dev->id));
+ if (queue_depth > max_depth)
+ queue_depth = max_depth;
+
+ scsi_adjust_queue_depth(sdev, MSG_SIMPLE_TAG, queue_depth);
+ return queue_depth;
+}
Index: drivers/scsi/scsi_lib.c
===================================================================
--- 3ac9a34948049bff79a2b2ce49c0a3c84e35a748/drivers/scsi/scsi_lib.c (mode:100644)
+++ uncommitted/drivers/scsi/scsi_lib.c (mode:100644)
@@ -1292,13 +1292,17 @@
shost = sdev->host;
while (!blk_queue_plugged(q)) {
int rtn;
+
+ if (!scsi_dev_queue_ready(q, sdev))
+ break;
+
/*
* get next queueable request. We do this early to make sure
* that the request is fully prepared even if we cannot
* accept it.
*/
req = elv_next_request(q);
- if (!req || !scsi_dev_queue_ready(q, sdev))
+ if (!req)
break;
if (unlikely(!scsi_device_online(sdev))) {
Index: include/linux/ata.h
===================================================================
--- 3ac9a34948049bff79a2b2ce49c0a3c84e35a748/include/linux/ata.h (mode:100644)
+++ uncommitted/include/linux/ata.h (mode:100644)
@@ -79,7 +79,8 @@
ATA_NIEN = (1 << 1), /* disable-irq flag */
ATA_LBA = (1 << 6), /* LBA28 selector */
ATA_DEV1 = (1 << 4), /* Select Device 1 (slave) */
- ATA_DEVICE_OBS = (1 << 7) | (1 << 5), /* obs bits in dev reg */
+ ATA_DEVICE_OBS = (1 << 5), /* obs bits in dev reg */
+ ATA_FPDMA_FUA = (1 << 7), /* FUA cache bypass bit */
ATA_DEVCTL_OBS = (1 << 3), /* obsolete bit in devctl reg */
ATA_BUSY = (1 << 7), /* BSY status bit */
ATA_DRDY = (1 << 6), /* device ready */
@@ -125,6 +126,12 @@
ATA_CMD_PACKET = 0xA0,
ATA_CMD_VERIFY = 0x40,
ATA_CMD_VERIFY_EXT = 0x42,
+ ATA_CMD_FPDMA_READ = 0x60,
+ ATA_CMD_FPDMA_WRITE = 0x61,
+ ATA_CMD_READ_LOG_EXT = 0x2f,
+
+ /* READ_LOG_EXT pages */
+ READ_LOG_SATA_NCQ_PAGE = 0x10,
/* SETFEATURES stuff */
SETFEATURES_XFER = 0x03,
@@ -233,7 +240,9 @@
#define ata_id_has_pm(id) ((id)[82] & (1 << 3))
#define ata_id_has_lba(id) ((id)[49] & (1 << 9))
#define ata_id_has_dma(id) ((id)[49] & (1 << 8))
+#define ata_id_has_ncq(id) ((id)[76] & (1 << 8))
#define ata_id_removeable(id) ((id)[0] & (1 << 7))
+#define ata_id_queue_depth(id) (((id)[75] & 0x1f) + 1)
#define ata_id_u32(id,n) \
(((u32) (id)[(n) + 1] << 16) | ((u32) (id)[(n)]))
#define ata_id_u64(id,n) \
Index: include/linux/libata.h
===================================================================
--- 3ac9a34948049bff79a2b2ce49c0a3c84e35a748/include/linux/libata.h (mode:100644)
+++ uncommitted/include/linux/libata.h (mode:100644)
@@ -80,7 +80,8 @@
LIBATA_MAX_PRD = ATA_MAX_PRD / 2,
ATA_MAX_PORTS = 8,
ATA_DEF_QUEUE = 1,
- ATA_MAX_QUEUE = 1,
+ ATA_MAX_CMDS = 31, /* to avoid SActive 0xffffffff error */
+ ATA_MAX_QUEUE = 30, /* leave one command for errors */
ATA_MAX_SECTORS = 200, /* FIXME */
ATA_MAX_BUS = 2,
ATA_DEF_BUSY_WAIT = 10000,
@@ -95,6 +96,7 @@
ATA_DFLAG_LBA48 = (1 << 0), /* device supports LBA48 */
ATA_DFLAG_PIO = (1 << 1), /* device currently in PIO mode */
ATA_DFLAG_LOCK_SECTORS = (1 << 2), /* don't adjust max_sectors */
+ ATA_DFLAG_NCQ = (1 << 3), /* Device can do NCQ */
ATA_DEV_UNKNOWN = 0, /* unknown device */
ATA_DEV_ATA = 1, /* ATA device */
@@ -113,11 +115,19 @@
ATA_FLAG_MMIO = (1 << 6), /* use MMIO, not PIO */
ATA_FLAG_SATA_RESET = (1 << 7), /* use COMRESET */
ATA_FLAG_PIO_DMA = (1 << 8), /* PIO cmds via DMA */
+ ATA_FLAG_NCQ = (1 << 9), /* Can do NCQ */
ATA_QCFLAG_ACTIVE = (1 << 1), /* cmd not yet ack'd to scsi lyer */
ATA_QCFLAG_SG = (1 << 3), /* have s/g table? */
ATA_QCFLAG_SINGLE = (1 << 4), /* no s/g, just a single buffer */
ATA_QCFLAG_DMAMAP = ATA_QCFLAG_SG | ATA_QCFLAG_SINGLE,
+ ATA_QCFLAG_NCQ = (1 << 5), /* using NCQ */
+ ATA_QCFLAG_DEFER = (1 << 6), /* ok to defer */
+ ATA_QCFLAG_ACCOUNT = (1 << 7),
+
+ ATA_QC_ISSUE_OK = 0,
+ ATA_QC_ISSUE_DEFER = 1,
+ ATA_QC_ISSUE_FATAL = 2,
/* various lengths of time */
ATA_TMOUT_EDD = 5 * HZ, /* hueristic */
@@ -305,9 +315,14 @@
struct ata_device device[ATA_MAX_DEVICES];
- struct ata_queued_cmd qcmd[ATA_MAX_QUEUE];
+ struct ata_queued_cmd qcmd[ATA_MAX_CMDS];
unsigned long qactive;
unsigned int active_tag;
+ int ncq_depth;
+ int depth;
+
+ wait_queue_head_t cmd_wait_queue;
+ unsigned int cmd_waiters;
struct ata_host_stats stats;
struct ata_host_set *host_set;
@@ -433,6 +448,9 @@
struct block_device *bdev,
sector_t capacity, int geom[]);
extern int ata_scsi_slave_config(struct scsi_device *sdev);
+extern int ata_scsi_change_queue_depth(struct scsi_device *, int);
+extern int ata_read_log_page(struct ata_port *, unsigned int, char, char *,
+ unsigned int);
#ifdef CONFIG_PCI
@@ -452,7 +470,7 @@
static inline unsigned int ata_tag_valid(unsigned int tag)
{
- return (tag < ATA_MAX_QUEUE) ? 1 : 0;
+ return (tag < ATA_MAX_CMDS) ? 1 : 0;
}
static inline unsigned int ata_dev_present(struct ata_device *dev)
--
Jens Axboe
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
