- remove enable_ci, ci interface is assumed to be present if the saa7113
is not found.
- reduce the delay when checking for saa7113
- clean up the cam reset according to specifications
- turn off Vcc to the cam slot if cam is removed or fails reset
- remove cam reset in ciintf_init
- clean up printks (KERN_)
- move gpio setting into saa7113_init
- clean up unreadable frontend_init
(Kenneth Aafloy)
Signed-off-by: Johannes Stezenbach <[email protected]>
---
drivers/media/dvb/ttpci/budget-av.c | 216 +++++++++++++++++++-----------------
1 files changed, 118 insertions(+), 98 deletions(-)
Index: linux-2.6.12-rc4/drivers/media/dvb/ttpci/budget-av.c
===================================================================
--- linux-2.6.12-rc4.orig/drivers/media/dvb/ttpci/budget-av.c 2005-05-08 18:12:25.000000000 +0200
+++ linux-2.6.12-rc4/drivers/media/dvb/ttpci/budget-av.c 2005-05-08 18:14:43.000000000 +0200
@@ -59,8 +59,12 @@ struct budget_av {
struct dvb_ca_en50221 ca;
};
-static int enable_ci = 0;
-
+/* GPIO CI Connections:
+ * 0 - Vcc/Reset (Reset is controlled by capacitor)
+ * 1 - Attribute Memory
+ * 2 - Card Enable (Active Low)
+ * 3 - Card Detect
+ */
/****************************************************************************
* INITIALIZATION
@@ -188,22 +192,35 @@ static int ciintf_slot_reset(struct dvb_
{
struct budget_av *budget_av = (struct budget_av *) ca->data;
struct saa7146_dev *saa = budget_av->budget.dev;
- int max = 20;
+ int timeout = 50; // 5 seconds (4.4.6 Ready)
if (slot != 0)
return -EINVAL;
dprintk(1, "ciintf_slot_reset\n");
- /* reset the card */
- saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTHI);
- msleep(100);
- saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTLO);
+ saa7146_setgpio(saa, 2, SAA7146_GPIO_OUTHI); /* disable card */
- while (--max > 0 && ciintf_read_attribute_mem(ca, slot, 0) != 0x1d)
+ saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTHI); /* Vcc off */
+ msleep(2);
+ saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTLO); /* Vcc on */
+ msleep(20); /* 20 ms Vcc settling time */
+
+ saa7146_setgpio(saa, 2, SAA7146_GPIO_OUTLO); /* enable card */
+
+ /* This should have been based on pin 16 READY of the pcmcia port,
+ * but AFAICS it is not routed to the saa7146 */
+ while (--timeout > 0 && ciintf_read_attribute_mem(ca, slot, 0) != 0x1d)
msleep(100);
- ttpci_budget_set_video_port(saa, BUDGET_VIDEO_PORTB);
+ if (timeout <= 0)
+ {
+ printk(KERN_ERR "budget-av: cam reset failed (timeout).\n");
+ saa7146_setgpio(saa, 2, SAA7146_GPIO_OUTHI); /* disable card */
+ saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTHI); /* Vcc off */
+ return -ETIMEDOUT;
+ }
+
return 0;
}
@@ -240,7 +257,6 @@ static int ciintf_poll_slot_status(struc
{
struct budget_av *budget_av = (struct budget_av *) ca->data;
struct saa7146_dev *saa = budget_av->budget.dev;
- int cam = 0;
if (slot != 0)
return -EINVAL;
@@ -248,15 +264,21 @@ static int ciintf_poll_slot_status(struc
if (!budget_av->slot_status) {
saa7146_setgpio(saa, 3, SAA7146_GPIO_INPUT);
udelay(1);
- cam = saa7146_read(saa, PSR) & MASK_06;
- saa7146_setgpio(saa, 3, SAA7146_GPIO_OUTLO);
-
- if (cam)
+ if (saa7146_read(saa, PSR) & MASK_06)
+ {
+ printk(KERN_INFO "budget-av: cam inserted\n");
budget_av->slot_status = 1;
+ }
+ saa7146_setgpio(saa, 3, SAA7146_GPIO_OUTLO);
} else if (!open) {
saa7146_setgpio(budget_av->budget.dev, 1, SAA7146_GPIO_OUTLO);
if (ttpci_budget_debiread(&budget_av->budget, DEBICICAM, 0, 1, 0, 1) == -ETIMEDOUT)
+ {
+ printk(KERN_INFO "budget-av: cam ejected\n");
+ saa7146_setgpio(saa, 2, SAA7146_GPIO_OUTHI); /* disable card */
+ saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTHI); /* Vcc off */
budget_av->slot_status = 0;
+ }
}
if (budget_av->slot_status == 1)
@@ -272,17 +294,11 @@ static int ciintf_init(struct budget_av
memset(&budget_av->ca, 0, sizeof(struct dvb_ca_en50221));
- /* setup GPIOs */
- saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTHI);
+ saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTLO);
+ saa7146_setgpio(saa, 1, SAA7146_GPIO_OUTLO);
saa7146_setgpio(saa, 2, SAA7146_GPIO_OUTLO);
saa7146_setgpio(saa, 3, SAA7146_GPIO_OUTLO);
- /* Reset the card */
- saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTHI);
- msleep(50);
- saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTLO);
- msleep(100);
-
/* Enable DEBI pins */
saa7146_write(saa, MC1, saa7146_read(saa, MC1) | (0x800 << 16) | 0x800);
@@ -297,13 +313,14 @@ static int ciintf_init(struct budget_av
budget_av->ca.slot_ts_enable = ciintf_slot_ts_enable;
budget_av->ca.poll_slot_status = ciintf_poll_slot_status;
budget_av->ca.data = budget_av;
+
if ((result = dvb_ca_en50221_init(&budget_av->budget.dvb_adapter,
&budget_av->ca, 0, 1)) != 0) {
- printk("budget_av: CI interface detected, but initialisation failed.\n");
+ printk(KERN_ERR "budget-av: ci initialisation failed.\n");
goto error;
}
- // success!
- printk("ciintf_init: CI interface initialised\n");
+
+ printk(KERN_INFO "budget-av: ci interface initialised.\n");
budget_av->budget.ci_present = 1;
return 0;
@@ -361,8 +378,12 @@ static const u8 saa7113_tab[] = {
static int saa7113_init(struct budget_av *budget_av)
{
struct budget *budget = &budget_av->budget;
+ struct saa7146_dev *saa = budget->dev;
const u8 *data = saa7113_tab;
+ saa7146_setgpio(saa, 0, SAA7146_GPIO_OUTHI);
+ msleep(200);
+
if (i2c_writereg(&budget->i2c_adap, 0x4a, 0x01, 0x08) != 1) {
dprintk(1, "saa7113 not found on KNC card\n");
return -ENODEV;
@@ -697,82 +718,90 @@ static u8 read_pwm(struct budget_av *bud
return pwm;
}
+#define SUBID_DVBS_KNC1 0x0010
+#define SUBID_DVBS_KNC1_PLUS 0x0011
+#define SUBID_DVBS_TYPHOON 0x4f56
+#define SUBID_DVBS_CINERGY1200 0x1154
+
+#define SUBID_DVBC_KNC1 0x0020
+#define SUBID_DVBC_KNC1_PLUS 0x0021
+#define SUBID_DVBC_CINERGY1200 0x1156
+
+#define SUBID_DVBT_KNC1_PLUS 0x0031
+#define SUBID_DVBT_KNC1 0x0030
+#define SUBID_DVBT_CINERGY1200 0x1157
static void frontend_init(struct budget_av *budget_av)
{
- switch (budget_av->budget.dev->pci->subsystem_device) {
- case 0x0011: // KNC1 DVB-S Plus budget with AV IN (stv0299/Philips SU1278(tsa5059))
- saa7146_write(budget_av->budget.dev, GPIO_CTRL, 0x50000000); // Enable / PowerON Frontend
- case 0x4f56: // Typhoon/KNC1 DVB-S budget (stv0299/Philips SU1278(tsa5059))
- case 0x0010: // KNC1 DVB-S budget (stv0299/Philips SU1278(tsa5059))
- budget_av->budget.dvb_frontend =
- stv0299_attach(&typhoon_config, &budget_av->budget.i2c_adap);
- if (budget_av->budget.dvb_frontend != NULL) {
+ struct saa7146_dev * saa = budget_av->budget.dev;
+ struct dvb_frontend * fe = NULL;
+
+ switch (saa->pci->subsystem_device) {
+ case SUBID_DVBS_KNC1_PLUS:
+ case SUBID_DVBC_KNC1_PLUS:
+ case SUBID_DVBT_KNC1_PLUS:
+ // Enable / PowerON Frontend
+ saa7146_setgpio(saa, 3, SAA7146_GPIO_OUTHI);
break;
- }
+ }
+
+ switch (saa->pci->subsystem_device) {
+
+ case SUBID_DVBS_KNC1:
+ case SUBID_DVBS_KNC1_PLUS:
+ case SUBID_DVBS_TYPHOON:
+ fe = stv0299_attach(&typhoon_config,
+ &budget_av->budget.i2c_adap);
break;
- case 0x0021: // KNC1 DVB-C Plus budget with AV IN (tda10021/Philips CU1216(tua6034))
- saa7146_write(budget_av->budget.dev, GPIO_CTRL, 0x50000000); // Enable / PowerON Frontend
- case 0x0020: // KNC1 DVB-C budget (tda10021/Philips CU1216(tua6034))
- budget_av->budget.dvb_frontend =
- tda10021_attach(&philips_cu1216_config,
- &budget_av->budget.i2c_adap, read_pwm(budget_av));
- if (budget_av->budget.dvb_frontend != NULL) {
- break;
- }
+ case SUBID_DVBS_CINERGY1200:
+ fe = stv0299_attach(&cinergy_1200s_config,
+ &budget_av->budget.i2c_adap);
break;
- case 0x0031: // KNC1 DVB-T Plus budget with AV IN (tda10046/Philips TU1216(tda6651tt))
- saa7146_write(budget_av->budget.dev, GPIO_CTRL, 0x50000000); // Enable / PowerON Frontend
- case 0x0030: // KNC1 DVB-T budget (tda10046/Philips TU1216(tda6651tt))
- budget_av->budget.dvb_frontend =
- tda10046_attach(&philips_tu1216_config, &budget_av->budget.i2c_adap);
- if (budget_av->budget.dvb_frontend != NULL) {
- break;
- }
+ case SUBID_DVBC_KNC1:
+ case SUBID_DVBC_KNC1_PLUS:
+ fe = tda10021_attach(&philips_cu1216_config,
+ &budget_av->budget.i2c_adap,
+ read_pwm(budget_av));
break;
- case 0x1154: // TerraTec Cinergy 1200 DVB-S (stv0299/Philips SU1278(tsa5059))
- budget_av->budget.dvb_frontend =
- stv0299_attach(&cinergy_1200s_config, &budget_av->budget.i2c_adap);
- if (budget_av->budget.dvb_frontend != NULL) {
- break;
- }
+ case SUBID_DVBT_KNC1:
+ case SUBID_DVBT_KNC1_PLUS:
+ fe = tda10046_attach(&philips_tu1216_config,
+ &budget_av->budget.i2c_adap);
break;
- case 0x1156: // Terratec Cinergy 1200 DVB-C (tda10021/Philips CU1216(tua6034))
- budget_av->budget.dvb_frontend =
- tda10021_attach(&philips_cu1216_config,
- &budget_av->budget.i2c_adap, read_pwm(budget_av));
- if (budget_av->budget.dvb_frontend) {
- break;
- }
+ case SUBID_DVBC_CINERGY1200:
+ fe = tda10021_attach(&philips_cu1216_config,
+ &budget_av->budget.i2c_adap,
+ read_pwm(budget_av));
break;
- case 0x1157: // Terratec Cinergy 1200 DVB-T (tda10046/Philips TU1216(tda6651tt))
- budget_av->budget.dvb_frontend =
- tda10046_attach(&philips_tu1216_config, &budget_av->budget.i2c_adap);
- if (budget_av->budget.dvb_frontend) {
- break;
- }
+ case SUBID_DVBT_CINERGY1200:
+ fe = tda10046_attach(&philips_tu1216_config,
+ &budget_av->budget.i2c_adap);
break;
}
- if (budget_av->budget.dvb_frontend == NULL) {
- printk("budget_av: A frontend driver was not found for device %04x/%04x subsystem %04x/%04x\n",
- budget_av->budget.dev->pci->vendor,
- budget_av->budget.dev->pci->device,
- budget_av->budget.dev->pci->subsystem_vendor,
- budget_av->budget.dev->pci->subsystem_device);
- } else {
- if (dvb_register_frontend
- (&budget_av->budget.dvb_adapter, budget_av->budget.dvb_frontend)) {
- printk("budget-av: Frontend registration failed!\n");
- if (budget_av->budget.dvb_frontend->ops->release)
- budget_av->budget.dvb_frontend->ops->release(budget_av->budget.dvb_frontend);
- budget_av->budget.dvb_frontend = NULL;
- }
+ if (fe == NULL) {
+ printk(KERN_ERR "budget-av: A frontend driver was not found "
+ "for device %04x/%04x subsystem %04x/%04x\n",
+ saa->pci->vendor,
+ saa->pci->device,
+ saa->pci->subsystem_vendor,
+ saa->pci->subsystem_device);
+ return;
+ }
+
+ budget_av->budget.dvb_frontend = fe;
+
+ if (dvb_register_frontend(&budget_av->budget.dvb_adapter,
+ budget_av->budget.dvb_frontend)) {
+ printk(KERN_ERR "budget-av: Frontend registration failed!\n");
+ if (budget_av->budget.dvb_frontend->ops->release)
+ budget_av->budget.dvb_frontend->ops->release(budget_av->budget.dvb_frontend);
+ budget_av->budget.dvb_frontend = NULL;
}
}
@@ -829,6 +858,7 @@ static int budget_av_attach(struct saa71
memset(budget_av, 0, sizeof(struct budget_av));
+ budget_av->has_saa7113 = 0;
budget_av->budget.ci_present = 0;
dev->ext_priv = budget_av;
@@ -843,10 +873,7 @@ static int budget_av_attach(struct saa71
saa7146_write(dev, DD1_INIT, 0x07000600);
saa7146_write(dev, MC2, MASK_09 | MASK_25 | MASK_10 | MASK_26);
- saa7146_setgpio(dev, 0, SAA7146_GPIO_OUTHI);
- msleep(500);
-
- if (0 == saa7113_init(budget_av)) {
+ if (saa7113_init(budget_av) == 0) {
budget_av->has_saa7113 = 1;
if (0 != saa7146_vv_init(dev, &vv_data)) {
@@ -867,9 +894,7 @@ static int budget_av_attach(struct saa71
saa7113_setinput(budget_av, 0);
} else {
- budget_av->has_saa7113 = 0;
-
- saa7146_setgpio(dev, 0, SAA7146_GPIO_OUTLO);
+ ciintf_init(budget_av);
}
/* fixme: find some sane values here... */
@@ -877,11 +902,11 @@ static int budget_av_attach(struct saa71
mac = budget_av->budget.dvb_adapter.proposed_mac;
if (i2c_readregs(&budget_av->budget.i2c_adap, 0xa0, 0x30, mac, 6)) {
- printk("KNC1-%d: Could not read MAC from KNC1 card\n",
+ printk(KERN_ERR "KNC1-%d: Could not read MAC from KNC1 card\n",
budget_av->budget.dvb_adapter.num);
memset(mac, 0, 6);
} else {
- printk("KNC1-%d: MAC addr = %.2x:%.2x:%.2x:%.2x:%.2x:%.2x\n",
+ printk(KERN_INFO "KNC1-%d: MAC addr = %.2x:%.2x:%.2x:%.2x:%.2x:%.2x\n",
budget_av->budget.dvb_adapter.num,
mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
}
@@ -889,9 +914,6 @@ static int budget_av_attach(struct saa71
budget_av->budget.dvb_adapter.priv = budget_av;
frontend_init(budget_av);
- if (enable_ci)
- ciintf_init(budget_av);
-
return 0;
}
@@ -1024,5 +1046,3 @@ MODULE_LICENSE("GPL");
MODULE_AUTHOR("Ralph Metzler, Marcus Metzler, Michael Hunold, others");
MODULE_DESCRIPTION("driver for the SAA7146 based so-called "
"budget PCI DVB w/ analog input and CI-module (e.g. the KNC cards)");
-module_param_named(enable_ci, enable_ci, int, 0644);
-MODULE_PARM_DESC(enable_ci, "Turn on/off CI module (default:off).");
--
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
