Hi,
I don't really know which person to send this bug report to so the list
suggested I send it to this address. Attached is the information about
the problem.
Regards
Gabriele Kalus
--
Gabriele Kalus, Ph.D.
System Administrator
Lund University, Physics Department
Box 118 SE-22100 Lund, SWEDEN
Phone: +46-462229675
Mobil: 0702-901227
Fax: +46-462224709
1. Repeated msg of kernel: drive_stat_acct: cmd not R/W? in kernel log
2. On a SuSE 9.0 the kernel was updated from kernel version 2.4.21-273-athlon to 2.4.21-280-athlon on the 4th of March.
The box act as a mailserver for approximately 500 users. The box has three Western Digital disks, one WDC WD400EB-00CPF0
and two WDC WD800BB-00BSA0. The two WDC WD800BB-00BSA0 disks are attached to a promise controllercard PDC20265 and are in raid1.
The mail are stored on the raid1. The message "kernel: drive_stat_acct: cmd not R/W?" only occurs when the raid is mounted.
On April the 29th the following happened
"Apr 29 06:01:33 samba kernel: PDC202XX: Primary channel reset.
Apr 29 06:01:33 samba kernel: PDC202XX: Secondary channel reset.
Apr 29 06:01:33 samba kernel: hde: timeout waiting for DMA
Apr 29 06:01:53 samba kernel: hde: dma_timer_expiry: dma status == 0x21
Apr 29 06:02:03 samba kernel: hde: timeout waiting for DMA
...
Apr 29 06:02:53 samba kernel: hdg: dma_timer_expiry: dma status == 0x21
Apr 29 06:03:03 samba kernel: hdg: timeout waiting for DMA
Apr 29 06:03:03 samba kernel: PDC202XX: Secondary channel reset.
Apr 29 06:03:03 samba kernel: PDC202XX: Primary channel reset.
Apr 29 06:03:03 samba kernel: hdg: timeout waiting for DMA
Apr 29 06:03:03 samba kernel: blk: queue c03ec17c, I/O limit 4095Mb (mask 0xffffffff)
..."
After further investigation it was noticed that the DMA mode was no longer activated at startup on the raid
disks, they were set in pio mode. At the 29th the system time also started to lag from usually -10 seconds per
day to +500 seconds per day.
Today the 1st of May the kernel was downgraded from 2.4.21-280 to the old version 2.4.21-273 and the error messages
are gone.
7.1 Output from scripts/ver_linux.output
Linux samba 2.4.21-273-athlon #1 Mon Jan 17 13:03:46 UTC 2005 i686 athlon i386 GNU/Linux
Gnu C 3.3.1
Gnu make 3.80
util-linux 2.11z
mount 2.11z
modutils 2.4.25
e2fsprogs 1.34
jfsutils 1.1.2
Linux C Library x 1 root root 1461208 Sep 24 2003 /lib/i686/libc.so.6
Dynamic linker (ldd) 2.3.2
Linux C++ Library 5.0.5
Procps 3.1.11
Net-tools 1.60
Kbd 1.08
Sh-utils 5.0
Modules Loaded isa-pnp thermal processor fan button af_packet battery ac ipt_TCPMSS
ipt_LOG ipt_TOS ipt_state eepro100 mii ip6t_LOG ip6t_REJECT ip6table_mangle ipt_REJECT
iptable_mangle iptable_filter ip_nat_ftp iptable_nat ip_conntrack_ftp ip_conntrack ip_tables
ip6table_filter ip6_tables ipv6 key lvm-mod raid1 ext3 jbd
7.2
/proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 4
model name : AMD Athlon(tm) Processor
stepping : 2
cpu MHz : 1009.055
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
bogomips : 1982.46
7.3
/proc/modules
isa-pnp 32712 0 (unused)
thermal 6180 0 (unused)
processor 8312 0 [thermal]
fan 1472 0 (unused)
button 2380 0 (unused)
af_packet 13192 1 (autoclean)
battery 5600 0 (unused)
ac 1696 0 (unused)
ipt_TCPMSS 2392 1 (autoclean)
ipt_LOG 3384 1 (autoclean)
ipt_TOS 1048 9 (autoclean)
ipt_state 568 56 (autoclean)
eepro100 19860 1
mii 2640 0 [eepro100]
ip6t_LOG 3704 0 (autoclean)
ip6t_REJECT 1528 3 (autoclean)
ip6table_mangle 2744 0 (autoclean) (unused)
ipt_REJECT 3288 3 (autoclean)
iptable_mangle 2168 1 (autoclean)
iptable_filter 1708 1 (autoclean)
ip_nat_ftp 2992 0 (unused)
iptable_nat 16366 1 [ip_nat_ftp]
ip_conntrack_ftp 3920 1
ip_conntrack 18084 3 [ipt_state ip_nat_ftp iptable_nat ip_conntrack_ftp]
ip_tables 11328 10 [ipt_TCPMSS ipt_LOG ipt_TOS ipt_state ipt_REJECT iptable_mangle iptable_filter iptable_nat]
ip6table_filter 1804 1 (autoclean)
ip6_tables 12224 4 [ip6t_LOG ip6t_REJECT ip6table_mangle ip6table_filter]
ipv6 227456 -1 (autoclean) [ip6t_REJECT]
key 70456 0 (autoclean) [ipv6]
lvm-mod 65508 0 (autoclean)
raid1 13744 1 (autoclean)
ext3 88552 2
jbd 52480 2 [ext3]
7.4
/proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
02f8-02ff : serial(auto)
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
8800-883f : Promise Technology, Inc. 20265
8800-8807 : ide2
8808-880f : ide3
8810-883f : PDC20265
9000-9003 : Promise Technology, Inc. 20265
9002-9002 : ide3
9400-9407 : Promise Technology, Inc. 20265
9400-9407 : ide3
9800-9803 : Promise Technology, Inc. 20265
9802-9802 : ide2
a000-a007 : Promise Technology, Inc. 20265
a000-a007 : ide2
a400-a43f : Intel Corp. 82557/8/9 [Ethernet Pro 100]
a400-a43f : eepro100
d000-d01f : VIA Technologies, Inc. USB (#2)
d400-d41f : VIA Technologies, Inc. USB
d800-d80f : VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE
d800-d807 : ide0
d808-d80f : ide1
e200-e27f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
e800-e80f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
/proc/iomem
00000000-0009efff : System RAM
0009f000-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cc000-000ce7ff : Extension ROM
000f0000-000fffff : System ROM
00100000-3ffebfff : System RAM
00100000-002b1099 : Kernel code
002b109a-00348943 : Kernel data
3ffec000-3ffeefff : ACPI Tables
3ffef000-3fffefff : reserved
3ffff000-3fffffff : ACPI Non-volatile Storage
d4800000-d481ffff : Promise Technology, Inc. 20265
d5000000-d501ffff : Intel Corp. 82557/8/9 [Ethernet Pro 100]
d5800000-d5800fff : Intel Corp. 82557/8/9 [Ethernet Pro 100]
d5800000-d5800fff : eepro100
d6000000-d7dfffff : PCI Bus #01
d6000000-d6ffffff : nVidia Corporation NV11 [GeForce2 MX]
d7f00000-e5ffffff : PCI Bus #01
d8000000-dfffffff : nVidia Corporation NV11 [GeForce2 MX]
d8000000-d9ffffff : vesafb
e6000000-e7ffffff : VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
ffff0000-ffffffff : reserved
7.5
lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e6000000 (32-bit, prefetchable) [size=32M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000dfff
Memory behind bridge: d6000000-d7dfffff
Prefetchable memory behind bridge: d7f00000-e5ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.2 USB Controller: VIA Technologies, Inc. USB (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.3 USB Controller: VIA Technologies, Inc. USB (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: Asustek Computer, Inc. A7V133/A7V133-C Mainboard
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0c)
Subsystem: Intel Corp. EtherExpress PRO/100 S Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d5800000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at a400 [size=64]
Region 2: Memory at d5000000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:11.0 Unknown mass storage controller: Promise Technology, Inc. 20265 (rev 02)
Subsystem: Promise Technology, Inc. Ultra100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at 9800 [size=4]
Region 2: I/O ports at 9400 [size=8]
Region 3: I/O ports at 9000 [size=4]
Region 4: I/O ports at 8800 [size=64]
Region 5: Memory at d4800000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev a1) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at d7ff0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
We downgraded to 2.4.21-273-athlon which seems to show that there is a problem with the SuSE 9.0 2.4.21-280-athlon kernel.
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
