my dell 2800 server with intel E7520 and broadcom pcie NIC runs fedora
C 3 (kernel updated to 2.6.11.6)now,
but on occasion it can not booting up wit acpi on.
ofen need me to shudown forcibly and open again.
When i turn apcioff with the option acpi=off in grub ,it boots up successfully.
i diff the dmesg of the acpi and noacpi boot up below:
and often the acpi booting will dead at
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
-ACPI wakeup devices:
-PCI0 PALO PBLO VPR0 PBHI VPR1 PICH
-ACPI: (supports S0 S4 S5)
and the line below is the last message shown in the acpi boot death scene .
i have no idear
regards
////////////////////////////////
the diff file :
--- 26116dmesg 2005-04-27 21:39:59.000000000 +0800
+++ 2611noacpi 2005-04-28 19:50:30.000000000 +0800
@@ -1,4 +1,12 @@
-reserved)
+Linux version 2.6.11.6 ([email protected]) (gcc version
3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #3 Wed Apr 27 20:59:11 CST 2005
+BIOS-provided physical RAM map:
+ BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
+ BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
+ BIOS-e820: 000000003ffc0000 - 000000003ffcfc00 (ACPI data)
+ BIOS-e820: 000000003ffcfc00 - 000000003ffff000 (reserved)
+ BIOS-e820: 00000000e0000000 - 00000000fec90000 (reserved)
+ BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
+ BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
@@ -7,31 +15,19 @@
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 32704 pages, LIFO batch:7
DMI 2.3 present.
-ACPI: RSDP (v000 DELL ) @ 0x000fd650
-ACPI: RSDT (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd664
-ACPI: FADT (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd6b0
-ACPI: MADT (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd724
-ACPI: SPCR (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd7cc
-ACPI: HPET (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd81c
-ACPI: MCFG (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd854
-ACPI: DSDT (v001 DELL PE BKC 0x00000001 MSFT 0x0100000e) @ 0x00000000
-ACPI: PM-Timer IO Port: 0x808
-ACPI: HPET id: 0xffffffff base: 0xfed00000
Allocating PCI resources starting at 40000000 (gap: 3ffff000:a0001000)
Built 1 zonelists
-Kernel command line: ro root=LABEL=/ rhgb quiet
+Kernel command line: ro root=LABEL=/ rhgb acpi=off
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
+Detected 2794.874 MHz processor.
+Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034300k/1048320k available (2607k kernel code, 13248k
reserved, 701k data, 188k init, 130816k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
-Using HPET for base-timer
-Using HPET for gettimeofday
-Detected 2793.416 MHz processor.
-Using hpet for high-res timesource
-Calibrating delay loop... 5537.79 BogoMIPS (lpj=2768896)
+Calibrating delay loop... 5521.40 BogoMIPS (lpj=2760704)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
@@ -52,62 +48,34 @@
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
-ACPI: setting ELCR to 0200 (from 0c88)
checking if image is initramfs... it is
Freeing initrd memory: 332k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbf0e, last bus=16
-PCI: Using MMCONFIG
+PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
-ACPI: Interpreter enabled
-ACPI: Using PIC for interrupt routing
-ACPI: PCI Root Bridge [PCI0] (00:00)
-PCI: Probing PCI hardware (bus 00)
-PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
-PCI: Transparent bridge - 0000:00:1e.0
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PALO._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PALO.DOBA._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PALO.DOBB._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PBLO._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.VPR0._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PBHI._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PBHI.PXB1._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PBHI.PXB2._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.VPR1._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.VPR1.PXC1._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.VPR1.PXC2._PRT]
-ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PICH._PRT]
-ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12)
-ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12)
-ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12)
-ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12)
-ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
-ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
-ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
-ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12)
+ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
-pnp: PnP ACPI init
-pnp: PnP ACPI: found 12 devices
+pnp: PnP ACPI: disabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
-PCI: Using ACPI for IRQ routing
-** PCI interrupts are no longer routed automatically. If this
-** causes a device to stop working, it is probably because the
-** driver failed to call pci_enable_device(). As a temporary
-** workaround, the "pci=routeirq" argument restores the old
-** behavior. If this argument makes the device work again,
-** please email the output of "lspci" to [email protected]
-** so I can fix the driver.
-pnp: 00:09: ioport range 0x800-0x87f could not be reserved
-pnp: 00:09: ioport range 0x880-0x8bf has been reserved
-pnp: 00:09: ioport range 0x8c0-0x8df has been reserved
-pnp: 00:09: ioport range 0xc00-0xc0f has been reserved
-pnp: 00:09: ioport range 0xc10-0xc1f has been reserved
-pnp: 00:09: ioport range 0xca0-0xcaf has been reserved
-pnp: 00:09: ioport range 0xc20-0xc3f has been reserved
+PCI: Probing PCI hardware
+PCI: Probing PCI hardware (bus 00)
+PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
+PCI: Transparent bridge - 0000:00:1e.0
+PCI: Using IRQ router PIIX/ICH [8086/24d0] at 0000:00:1f.0
+PCI: IRQ 0 for device 0000:00:02.0 doesn't match PIRQ mask - try
pci=usepirqmask
+PCI: Found IRQ 11 for device 0000:00:02.0
+PCI: Sharing IRQ 11 with 0000:00:03.0
+PCI: Sharing IRQ 11 with 0000:00:04.0
+PCI: Sharing IRQ 11 with 0000:00:05.0
+PCI: Sharing IRQ 11 with 0000:00:06.0
+PCI: Sharing IRQ 11 with 0000:00:1d.0
+PCI: Sharing IRQ 11 with 0000:07:00.0
+PCI: Sharing IRQ 11 with 0000:0b:07.0
+PCI: Sharing IRQ 11 with 0000:0d:00.0
apm: BIOS not found.
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
@@ -125,7 +93,6 @@
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
-ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
@@ -135,7 +102,6 @@
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
-ACPI: PCI interrupt 0000:00:1f.1[A]: no GSI - using IRQ 0
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
@@ -167,16 +133,13 @@
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
-ACPI wakeup devices:
-PCI0 PALO PBLO VPR0 PBHI VPR1 PICH
-ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 188k freed
megaraid cmm: 2.20.2.5 (Release Date: Fri Jan 21 00:01:03 EST 2005)
megaraid: 2.20.4.5 (Release Date: Thu Feb 03 12:27:22 EST 2005)
megaraid: probe new device 0x1028:0x0013:0x1028:0x016e: bus 2:slot 14:func 0
-ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
-PCI: setting IRQ 7 as level-triggered
-ACPI: PCI interrupt 0000:02:0e.0[A] -> GSI 7 (level, low) -> IRQ 7
+PCI: Found IRQ 7 for device 0000:02:0e.0
+PCI: Sharing IRQ 7 with 0000:00:1d.2
+PCI: Sharing IRQ 7 with 0000:10:0d.0
megaraid: fw version:[513O] bios version:[H418]
scsi0 : LSI Logic MegaRAID driver
scsi[0]: scanning scsi channel 0 [Phy 0] for non-raid devices
@@ -218,27 +181,46 @@
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
tg3.c:v3.23 (February 15, 2005)
-ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
-PCI: setting IRQ 11 as level-triggered
-ACPI: PCI interrupt 0000:07:00.0[A] -> GSI 11 (level, low) -> IRQ 11
+PCI: Found IRQ 11 for device 0000:07:00.0
+PCI: Sharing IRQ 11 with 0000:00:02.0
+PCI: Sharing IRQ 11 with 0000:00:03.0
+PCI: Sharing IRQ 11 with 0000:00:04.0
+PCI: Sharing IRQ 11 with 0000:00:05.0
+PCI: Sharing IRQ 11 with 0000:00:06.0
+PCI: Sharing IRQ 11 with 0000:00:1d.0
+PCI: Sharing IRQ 11 with 0000:0d:00.0
+PCI: Sharing IRQ 11 with 0000:0b:07.0
PCI: Setting latency timer of device 0000:07:00.0 to 64
eth0: Tigon3 [partno(BCM95721A211) rev 4101 PHY(5750)]
(PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:10:18:0e:06:49
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
-ACPI: PCI interrupt 0000:0d:00.0[A] -> GSI 11 (level, low) -> IRQ 11
+PCI: Found IRQ 11 for device 0000:0d:00.0
+PCI: Sharing IRQ 11 with 0000:00:02.0
+PCI: Sharing IRQ 11 with 0000:00:03.0
+PCI: Sharing IRQ 11 with 0000:00:04.0
+PCI: Sharing IRQ 11 with 0000:00:05.0
+PCI: Sharing IRQ 11 with 0000:00:06.0
+PCI: Sharing IRQ 11 with 0000:00:1d.0
+PCI: Sharing IRQ 11 with 0000:07:00.0
+PCI: Sharing IRQ 11 with 0000:0b:07.0
PCI: Setting latency timer of device 0000:0d:00.0 to 64
eth1: Tigon3 [partno(BCM95721A211) rev 4101 PHY(5750)]
(PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:10:18:0e:06:ab
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
Intel(R) PRO/1000 Network Driver - version 5.6.10.1-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
-ACPI: PCI interrupt 0000:0b:07.0[A] -> GSI 11 (level, low) -> IRQ 11
+PCI: Found IRQ 11 for device 0000:0b:07.0
+PCI: Sharing IRQ 11 with 0000:00:02.0
+PCI: Sharing IRQ 11 with 0000:00:03.0
+PCI: Sharing IRQ 11 with 0000:00:04.0
+PCI: Sharing IRQ 11 with 0000:00:05.0
+PCI: Sharing IRQ 11 with 0000:00:06.0
+PCI: Sharing IRQ 11 with 0000:00:1d.0
+PCI: Sharing IRQ 11 with 0000:07:00.0
+PCI: Sharing IRQ 11 with 0000:0d:00.0
e1000: eth2: e1000_probe: Intel(R) PRO/1000 Network Connection
-ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
-ACPI: PCI interrupt 0000:0c:08.0[A] -> GSI 11 (level, low) -> IRQ 11
+PCI: Found IRQ 11 for device 0000:0c:08.0
e1000: eth3: e1000_probe: Intel(R) PRO/1000 Network Connection
hw_random hardware driver 1.0.0 loaded
-ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3
-PCI: setting IRQ 3 as level-triggered
-ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 3 (level, low) -> IRQ 3
+PCI: Found IRQ 3 for device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 3, pci mem 0xdff00000
@@ -248,16 +230,22 @@
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
-ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
+PCI: Found IRQ 11 for device 0000:00:1d.0
+PCI: Sharing IRQ 11 with 0000:00:02.0
+PCI: Sharing IRQ 11 with 0000:00:03.0
+PCI: Sharing IRQ 11 with 0000:00:04.0
+PCI: Sharing IRQ 11 with 0000:00:05.0
+PCI: Sharing IRQ 11 with 0000:00:06.0
+PCI: Sharing IRQ 11 with 0000:07:00.0
+PCI: Sharing IRQ 11 with 0000:0d:00.0
+PCI: Sharing IRQ 11 with 0000:0b:07.0
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 0x7ce0
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
-ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
-PCI: setting IRQ 10 as level-triggered
-ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 10 (level, low) -> IRQ 10
+PCI: Found IRQ 10 for device 0000:00:1d.1
uhci_hcd 0000:00:1d.1: UHCI Host Controller
usb 1-3: new high speed USB device using ehci_hcd and address 2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
@@ -265,7 +253,9 @@
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
-ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 7 (level, low) -> IRQ 7
+PCI: Found IRQ 7 for device 0000:00:1d.2
+PCI: Sharing IRQ 7 with 0000:02:0e.0
+PCI: Sharing IRQ 7 with 0000:10:0d.0
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 7, io base 0x7ca0
@@ -281,9 +271,6 @@
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03ff220(lo)
IPv6 over IPv4 tunneling driver
-ACPI: Power Button (FF) [PWRF]
-ibm_acpi: ec object not found
-ACPI: Video Device [EVGA] (multi-head: no rom: yes post: no)
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected]
hda: packet command error: status=0x51 { DriveReady SeekComplete Error }
hda: packet command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
@@ -291,10 +278,8 @@
cdrom: open failed.
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
-parport: PnPBIOS parport detected.
-parport0: PC-style at 0x278 (0x678), irq 5 [PCSPP,TRISTATE]
-Trying to free free DMA1
-pnp: Device 00:08 disabled.
+parport0: PC-style at 0x278 (0x678) [PCSPP,TRISTATE]
+parport0: irq 5 detected
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth0: Link is up at 100 Mbps, full duplex.
@@ -304,10 +289,13 @@
eth2: no IPv6 routers present
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
i2c /dev entries driver
-pnp: Device 00:08 activated.
-parport: PnPBIOS parport detected.
-parport0: PC-style at 0x278 (0x678), irq 5 [PCSPP,TRISTATE]
-lp0: using parport0 (interrupt-driven).
+parport0: PC-style at 0x278 (0x678) [PCSPP,TRISTATE]
+parport0: irq 5 detected
+lp0: using parport0 (polling).
lp0: console ready
-ACPI: PCI interrupt 0000:10:0d.0[A] -> GSI 7 (level, low) -> IRQ 7
+PCI: Found IRQ 7 for device 0000:10:0d.0
+PCI: Sharing IRQ 7 with 0000:00:1d.2
+PCI: Sharing IRQ 7 with 0000:02:0e.0
[drm] Initialized radeon 1.14.0 20050125 on minor 0:
+pciehp: Unknown symbol pcie_port_service_register
+pciehp: Unknown symbol pcie_port_service_unregister
--
we who r about to die,salute u!
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
