* Luck, Tony <[email protected]> wrote:
> >tested on x86, and all other arches should work as well, but if an
> >architecture has irqs-off assumptions in its switch_to() logic
> >it might break. (I havent found any but there may such assumptions.)
>
> The ia64_switch_to() code includes a section that can change a pinned
> MMU mapping (when the stack for the new process is in a different
> granule from the stack for the old process). [...]
thanks - updated patch below. Any other architectures that switch the
kernel stack in a nonatomic way? x86/x64 switches it atomically.
Ingo
Signed-off-by: Ingo Molnar <[email protected]>
--- linux/kernel/sched.c.orig
+++ linux/kernel/sched.c
@@ -222,7 +222,6 @@ struct runqueue {
unsigned long expired_timestamp;
unsigned long long timestamp_last_tick;
task_t *curr, *idle;
- struct mm_struct *prev_mm;
prio_array_t *active, *expired, arrays[2];
int best_expired_prio;
atomic_t nr_iowait;
@@ -276,71 +275,25 @@ static DEFINE_PER_CPU(struct runqueue, r
#define task_rq(p) cpu_rq(task_cpu(p))
#define cpu_curr(cpu) (cpu_rq(cpu)->curr)
-#ifndef prepare_arch_switch
-# define prepare_arch_switch(next) do { } while (0)
-#endif
-#ifndef finish_arch_switch
-# define finish_arch_switch(prev) do { } while (0)
-#endif
-
-#ifndef __ARCH_WANT_UNLOCKED_CTXSW
-static inline int task_running(runqueue_t *rq, task_t *p)
-{
- return rq->curr == p;
-}
-
-static inline void prepare_lock_switch(runqueue_t *rq, task_t *next)
-{
-}
-
-static inline void finish_lock_switch(runqueue_t *rq, task_t *prev)
-{
- spin_unlock_irq(&rq->lock);
-}
-
-#else /* __ARCH_WANT_UNLOCKED_CTXSW */
-static inline int task_running(runqueue_t *rq, task_t *p)
+/*
+ * We can optimise this out completely for !SMP, because the
+ * SMP rebalancing from interrupt is the only thing that cares:
+ */
+static inline void set_task_on_cpu(struct task_struct *p, int val)
{
#ifdef CONFIG_SMP
- return p->oncpu;
-#else
- return rq->curr == p;
+ p->on_cpu = val;
#endif
}
-static inline void prepare_lock_switch(runqueue_t *rq, task_t *next)
+static inline int task_on_cpu(runqueue_t *rq, task_t *p)
{
#ifdef CONFIG_SMP
- /*
- * We can optimise this out completely for !SMP, because the
- * SMP rebalancing from interrupt is the only thing that cares
- * here.
- */
- next->oncpu = 1;
-#endif
-#ifdef __ARCH_WANT_INTERRUPTS_ON_CTXSW
- spin_unlock_irq(&rq->lock);
+ return p->on_cpu;
#else
- spin_unlock(&rq->lock);
-#endif
-}
-
-static inline void finish_lock_switch(runqueue_t *rq, task_t *prev)
-{
-#ifdef CONFIG_SMP
- /*
- * After ->oncpu is cleared, the task can be moved to a different CPU.
- * We must ensure this doesn't happen until the switch is completely
- * finished.
- */
- smp_wmb();
- prev->oncpu = 0;
-#endif
-#ifndef __ARCH_WANT_INTERRUPTS_ON_CTXSW
- local_irq_enable();
+ return rq->curr == p;
#endif
}
-#endif /* __ARCH_WANT_UNLOCKED_CTXSW */
/*
* task_rq_lock - lock the runqueue a given task resides on and disable
@@ -855,7 +808,7 @@ static int migrate_task(task_t *p, int d
* If the task is not on a runqueue (and not running), then
* it is sufficient to simply update the task's cpu field.
*/
- if (!p->array && !task_running(rq, p)) {
+ if (!p->array && !task_on_cpu(rq, p)) {
set_task_cpu(p, dest_cpu);
return 0;
}
@@ -885,9 +838,9 @@ void wait_task_inactive(task_t * p)
repeat:
rq = task_rq_lock(p, &flags);
/* Must be off runqueue entirely, not preempted. */
- if (unlikely(p->array || task_running(rq, p))) {
+ if (unlikely(p->array || task_on_cpu(rq, p))) {
/* If it's preempted, we yield. It could be a while. */
- preempted = !task_running(rq, p);
+ preempted = !task_on_cpu(rq, p);
task_rq_unlock(rq, &flags);
cpu_relax();
if (preempted)
@@ -1150,7 +1103,7 @@ static int try_to_wake_up(task_t * p, un
this_cpu = smp_processor_id();
#ifdef CONFIG_SMP
- if (unlikely(task_running(rq, p)))
+ if (unlikely(task_on_cpu(rq, p)))
goto out_activate;
new_cpu = cpu;
@@ -1311,9 +1264,7 @@ void fastcall sched_fork(task_t *p, int
#ifdef CONFIG_SCHEDSTATS
memset(&p->sched_info, 0, sizeof(p->sched_info));
#endif
-#if defined(CONFIG_SMP) && defined(__ARCH_WANT_UNLOCKED_CTXSW)
- p->oncpu = 0;
-#endif
+ set_task_on_cpu(p, 0);
#ifdef CONFIG_PREEMPT
/* Want to start with kernel preemption disabled. */
p->thread_info->preempt_count = 1;
@@ -1458,45 +1409,11 @@ void fastcall sched_exit(task_t * p)
}
/**
- * prepare_task_switch - prepare to switch tasks
- * @rq: the runqueue preparing to switch
- * @next: the task we are going to switch to.
- *
- * This is called with the rq lock held and interrupts off. It must
- * be paired with a subsequent finish_task_switch after the context
- * switch.
- *
- * prepare_task_switch sets up locking and calls architecture specific
- * hooks.
- */
-static inline void prepare_task_switch(runqueue_t *rq, task_t *next)
-{
- prepare_lock_switch(rq, next);
- prepare_arch_switch(next);
-}
-
-/**
- * finish_task_switch - clean up after a task-switch
+ * __schedule_tail - switch to the new MM and clean up after a task-switch
* @prev: the thread we just switched away from.
- *
- * finish_task_switch must be called after the context switch, paired
- * with a prepare_task_switch call before the context switch.
- * finish_task_switch will reconcile locking set up by prepare_task_switch,
- * and do any other architecture-specific cleanup actions.
- *
- * Note that we may have delayed dropping an mm in context_switch(). If
- * so, we finish that here outside of the runqueue lock. (Doing it
- * with the lock held can cause deadlocks; see schedule() for
- * details.)
*/
-static inline void finish_task_switch(runqueue_t *rq, task_t *prev)
- __releases(rq->lock)
+static void __schedule_tail(task_t *prev)
{
- struct mm_struct *mm = rq->prev_mm;
- unsigned long prev_task_flags;
-
- rq->prev_mm = NULL;
-
/*
* A task struct has one reference for the use as "current".
* If a task dies, then it sets EXIT_ZOMBIE in tsk->exit_state and
@@ -1508,11 +1425,34 @@ static inline void finish_task_switch(ru
* be dropped twice.
* Manfred Spraul <[email protected]>
*/
- prev_task_flags = prev->flags;
- finish_arch_switch(prev);
- finish_lock_switch(rq, prev);
- if (mm)
- mmdrop(mm);
+ struct task_struct *next = current;
+ unsigned long prev_task_flags = prev->flags;
+ struct mm_struct *prev_mm = prev->active_mm, *next_mm = next->mm;
+
+ /*
+ * Switch the MM first:
+ */
+ if (unlikely(!next_mm)) {
+ next->active_mm = prev_mm;
+ atomic_inc(&prev_mm->mm_count);
+ enter_lazy_tlb(prev_mm, next);
+ } else
+ switch_mm(prev_mm, next_mm, next);
+
+ if (unlikely(!prev->mm))
+ prev->active_mm = NULL;
+ else
+ prev_mm = NULL;
+ /*
+ * After ->on_cpu is cleared, the previous task is free to be
+ * moved to a different CPU. We must ensure this doesn't happen
+ * until the switch is completely finished.
+ */
+ smp_wmb();
+ set_task_on_cpu(prev, 0);
+
+ if (prev_mm)
+ mmdrop(prev_mm);
if (unlikely(prev_task_flags & PF_DEAD))
put_task_struct(prev);
}
@@ -1522,48 +1462,15 @@ static inline void finish_task_switch(ru
* @prev: the thread we just switched away from.
*/
asmlinkage void schedule_tail(task_t *prev)
- __releases(rq->lock)
{
- runqueue_t *rq = this_rq();
- finish_task_switch(rq, prev);
-#ifdef __ARCH_WANT_UNLOCKED_CTXSW
- /* In this case, finish_task_switch does not reenable preemption */
+ __schedule_tail(prev);
+ /* __schedule_tail does not reenable preemption: */
preempt_enable();
-#endif
if (current->set_child_tid)
put_user(current->pid, current->set_child_tid);
}
/*
- * context_switch - switch to the new MM and the new
- * thread's register state.
- */
-static inline
-task_t * context_switch(runqueue_t *rq, task_t *prev, task_t *next)
-{
- struct mm_struct *mm = next->mm;
- struct mm_struct *oldmm = prev->active_mm;
-
- if (unlikely(!mm)) {
- next->active_mm = oldmm;
- atomic_inc(&oldmm->mm_count);
- enter_lazy_tlb(oldmm, next);
- } else
- switch_mm(oldmm, mm, next);
-
- if (unlikely(!prev->mm)) {
- prev->active_mm = NULL;
- WARN_ON(rq->prev_mm);
- rq->prev_mm = oldmm;
- }
-
- /* Here we just switch the register state and the stack. */
- switch_to(prev, next, prev);
-
- return prev;
-}
-
-/*
* nr_running, nr_uninterruptible and nr_context_switches:
*
* externally visible scheduler statistics: current number of runnable
@@ -1763,7 +1670,7 @@ int can_migrate_task(task_t *p, runqueue
return 0;
*all_pinned = 0;
- if (task_running(rq, p))
+ if (task_on_cpu(rq, p))
return 0;
/*
@@ -2900,16 +2807,30 @@ switch_tasks:
rq->nr_switches++;
rq->curr = next;
++*switch_count;
-
- prepare_task_switch(rq, next);
- prev = context_switch(rq, prev, next);
+ set_task_on_cpu(next, 1);
+ /*
+ * We release the runqueue lock and enable interrupts,
+ * but preemption is disabled until the end of the
+ * context-switch:
+ */
+ spin_unlock_irq(&rq->lock);
+ /*
+ * Switch kernel stack and register state. Updates
+ * 'prev' to point to the real previous task.
+ *
+ * Here we are still in the old task, 'prev' is current,
+ * 'next' is the task we are going to switch to:
+ */
+ switch_to(prev, next, prev);
barrier();
/*
- * this_rq must be evaluated again because prev may have moved
- * CPUs since it called schedule(), thus the 'rq' on its stack
- * frame will be invalid.
+ * Here we are in the new task's stack already. 'prev'
+ * has been updated by switch_to() to point to the task
+ * we just switched from, 'next' is invalid.
+ *
+ * do the MM switch and clean up:
*/
- finish_task_switch(this_rq(), prev);
+ __schedule_tail(prev);
} else
spin_unlock_irq(&rq->lock);
@@ -3358,7 +3279,7 @@ void set_user_nice(task_t *p, long nice)
* If the task increased its priority or is running and
* lowered its priority, then reschedule its CPU:
*/
- if (delta < 0 || (delta > 0 && task_running(rq, p)))
+ if (delta < 0 || (delta > 0 && task_on_cpu(rq, p)))
resched_task(rq->curr);
}
out_unlock:
@@ -3548,7 +3469,7 @@ recheck:
* our priority decreased, or if we are not currently running on
* this runqueue and our priority is higher than the current's
*/
- if (task_running(rq, p)) {
+ if (task_on_cpu(rq, p)) {
if (p->prio > oldprio)
resched_task(rq->curr);
} else if (TASK_PREEMPTS_CURR(p, rq))
@@ -4157,9 +4078,7 @@ void __devinit init_idle(task_t *idle, i
spin_lock_irqsave(&rq->lock, flags);
rq->curr = rq->idle = idle;
-#if defined(CONFIG_SMP) && defined(__ARCH_WANT_UNLOCKED_CTXSW)
- idle->oncpu = 1;
-#endif
+ set_task_on_cpu(idle, 1);
set_tsk_need_resched(idle);
spin_unlock_irqrestore(&rq->lock, flags);
--- include/asm-ia64/system.h.orig
+++ include/asm-ia64/system.h
@@ -226,7 +226,9 @@ extern void ia64_load_extra (struct task
if (IA64_HAS_EXTRA_STATE(next)) \
ia64_load_extra(next); \
ia64_psr(ia64_task_regs(next))->dfh = !ia64_is_local_fpu_owner(next); \
+ local_irq_disable(); \
(last) = ia64_switch_to((next)); \
+ local_irq_enable(); \
} while (0)
#ifdef CONFIG_SMP
@@ -248,32 +250,6 @@ extern void ia64_load_extra (struct task
# define switch_to(prev,next,last) __switch_to(prev, next, last)
#endif
-/*
- * On IA-64, we don't want to hold the runqueue's lock during the low-level context-switch,
- * because that could cause a deadlock. Here is an example by Erich Focht:
- *
- * Example:
- * CPU#0:
- * schedule()
- * -> spin_lock_irq(&rq->lock)
- * -> context_switch()
- * -> wrap_mmu_context()
- * -> read_lock(&tasklist_lock)
- *
- * CPU#1:
- * sys_wait4() or release_task() or forget_original_parent()
- * -> write_lock(&tasklist_lock)
- * -> do_notify_parent()
- * -> wake_up_parent()
- * -> try_to_wake_up()
- * -> spin_lock_irq(&parent_rq->lock)
- *
- * If the parent's rq happens to be on CPU#0, we'll wait for the rq->lock
- * of that CPU which will not be released, because there we wait for the
- * tasklist_lock to become available.
- */
-#define __ARCH_WANT_UNLOCKED_CTXSW
-
#define ia64_platform_is(x) (strcmp(x, platform_name) == 0)
void cpu_idle_wait(void);
--- linux/include/asm-sparc/system.h.orig
+++ linux/include/asm-sparc/system.h
@@ -94,22 +94,6 @@ extern void fpsave(unsigned long *fpregs
} while(0)
#endif
-/*
- * Flush windows so that the VM switch which follows
- * would not pull the stack from under us.
- *
- * SWITCH_ENTER and SWITH_DO_LAZY_FPU do not work yet (e.g. SMP does not work)
- * XXX WTF is the above comment? Found in late teen 2.4.x.
- */
-#define prepare_arch_switch(next) do { \
- __asm__ __volatile__( \
- ".globl\tflush_patch_switch\nflush_patch_switch:\n\t" \
- "save %sp, -0x40, %sp; save %sp, -0x40, %sp; save %sp, -0x40, %sp\n\t" \
- "save %sp, -0x40, %sp; save %sp, -0x40, %sp; save %sp, -0x40, %sp\n\t" \
- "save %sp, -0x40, %sp\n\t" \
- "restore; restore; restore; restore; restore; restore; restore"); \
-} while(0)
-
/* Much care has gone into this code, do not touch it.
*
* We need to loadup regs l0/l1 for the newly forked child
@@ -122,6 +106,12 @@ extern void fpsave(unsigned long *fpregs
* - Anton & Pete
*/
#define switch_to(prev, next, last) do { \
+ __asm__ __volatile__( \
+ ".globl\tflush_patch_switch\nflush_patch_switch:\n\t" \
+ "save %sp, -0x40, %sp; save %sp, -0x40, %sp; save %sp, -0x40, %sp\n\t" \
+ "save %sp, -0x40, %sp; save %sp, -0x40, %sp; save %sp, -0x40, %sp\n\t" \
+ "save %sp, -0x40, %sp\n\t" \
+ "restore; restore; restore; restore; restore; restore; restore"); \
SWITCH_ENTER(prev); \
SWITCH_DO_LAZY_FPU(next); \
cpu_set(smp_processor_id(), next->active_mm->cpu_vm_mask); \
--- linux/include/asm-arm/system.h.orig
+++ linux/include/asm-arm/system.h
@@ -142,13 +142,6 @@ extern unsigned int user_debug;
#define nop() __asm__ __volatile__("mov\tr0,r0\t@ nop\n\t");
/*
- * switch_mm() may do a full cache flush over the context switch,
- * so enable interrupts over the context switch to avoid high
- * latency.
- */
-#define __ARCH_WANT_INTERRUPTS_ON_CTXSW
-
-/*
* switch_to(prev, next) should switch from task `prev' to `next'
* `prev' will never be the same as `next'. schedule() itself
* contains the memory barrier to tell GCC not to cache `current'.
--- linux/include/asm-s390/system.h.orig
+++ linux/include/asm-s390/system.h
@@ -101,6 +101,8 @@ static inline void restore_access_regs(u
save_access_regs(&prev->thread.acrs[0]); \
restore_access_regs(&next->thread.acrs[0]); \
prev = __switch_to(prev,next); \
+ set_fs(current->thread.mm_segment); \
+ account_system_vtime(prev); \
} while (0)
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
@@ -110,11 +112,6 @@ extern void account_system_vtime(struct
#define account_system_vtime(prev) do { } while (0)
#endif
-#define finish_arch_switch(rq, prev) do { \
- set_fs(current->thread.mm_segment); \
- account_system_vtime(prev); \
-} while (0)
-
#define nop() __asm__ __volatile__ ("nop")
#define xchg(ptr,x) \
--- linux/include/linux/sched.h.orig
+++ linux/include/linux/sched.h
@@ -367,11 +367,6 @@ struct signal_struct {
#endif
};
-/* Context switch must be unlocked if interrupts are to be enabled */
-#ifdef __ARCH_WANT_INTERRUPTS_ON_CTXSW
-# define __ARCH_WANT_UNLOCKED_CTXSW
-#endif
-
/*
* Bits in flags field of signal_struct.
*/
@@ -597,8 +592,8 @@ struct task_struct {
int lock_depth; /* Lock depth */
-#if defined(CONFIG_SMP) && defined(__ARCH_WANT_UNLOCKED_CTXSW)
- int oncpu;
+#if defined(CONFIG_SMP)
+ int on_cpu;
#endif
int prio, static_prio;
struct list_head run_list;
--- linux/include/asm-arm26/system.h.orig
+++ linux/include/asm-arm26/system.h
@@ -94,15 +94,6 @@ extern unsigned int user_debug;
#define set_wmb(var, value) do { var = value; wmb(); } while (0)
/*
- * We assume knowledge of how
- * spin_unlock_irq() and friends are implemented. This avoids
- * us needlessly decrementing and incrementing the preempt count.
- */
-#define prepare_arch_switch(rq,next) local_irq_enable()
-#define finish_arch_switch(rq,prev) spin_unlock(&(rq)->lock)
-#define task_running(rq,p) ((rq)->curr == (p))
-
-/*
* switch_to(prev, next) should switch from task `prev' to `next'
* `prev' will never be the same as `next'. schedule() itself
* contains the memory barrier to tell GCC not to cache `current'.
--- linux/include/asm-sparc64/system.h.orig
+++ linux/include/asm-sparc64/system.h
@@ -139,13 +139,6 @@ extern void __flushw_user(void);
#define flush_user_windows flushw_user
#define flush_register_windows flushw_all
-/* Don't hold the runqueue lock over context switch */
-#define __ARCH_WANT_UNLOCKED_CTXSW
-#define prepare_arch_switch(next) \
-do { \
- flushw_all(); \
-} while (0)
-
/* See what happens when you design the chip correctly?
*
* We tell gcc we clobber all non-fixed-usage registers except
@@ -161,7 +154,8 @@ do { \
#define EXTRA_CLOBBER
#endif
#define switch_to(prev, next, last) \
-do { if (test_thread_flag(TIF_PERFCTR)) { \
+do { flushw_all(); \
+ if (test_thread_flag(TIF_PERFCTR)) { \
unsigned long __tmp; \
read_pcr(__tmp); \
current_thread_info()->pcr_reg = __tmp; \
--- linux/include/asm-mips/system.h.orig
+++ linux/include/asm-mips/system.h
@@ -421,12 +421,6 @@ extern void __die_if_kernel(const char *
extern int stop_a_enabled;
-/*
- * See include/asm-ia64/system.h; prevents deadlock on SMP
- * systems.
- */
-#define __ARCH_WANT_UNLOCKED_CTXSW
-
#define arch_align_stack(x) (x)
#endif /* _ASM_SYSTEM_H */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
