Something funky going on with ACPI on nForce2? NFS is no go either.
Linux version 2.6.12-rc1-mm3 (root@blaze) (gcc version 3.3.4) #2
PREEMPT Fri Mar 25 14:30:56 EST 2005
[snip ...]
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: nForce2 C1 Halt Disconnect fixup
Boot video device is 0000:03:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Can't get handler for 0000:00:00.1
ACPI: Can't get handler for 0000:00:00.2
ACPI: Can't get handler for 0000:00:00.3
ACPI: Can't get handler for 0000:00:00.4
ACPI: Can't get handler for 0000:00:00.5
ACPI: Can't get handler for 0000:01:0a.0
ACPI: Can't get handler for 0000:01:0b.0
ACPI: Can't get handler for 0000:01:0c.0
ACPI: Can't get handler for 0000:03:00.1
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: No ACPI bus support for 00:00
ACPI: No ACPI bus support for 00:01
ACPI: No ACPI bus support for 00:02
ACPI: No ACPI bus support for 00:03
ACPI: No ACPI bus support for 00:04
ACPI: No ACPI bus support for 00:05
ACPI: No ACPI bus support for 00:06
ACPI: No ACPI bus support for 00:07
ACPI: No ACPI bus support for 00:08
ACPI: No ACPI bus support for 00:09
ACPI: No ACPI bus support for 00:0a
ACPI: No ACPI bus support for 00:0b
ACPI: No ACPI bus support for 00:0c
ACPI: No ACPI bus support for 00:0d
pnp: PnP ACPI: found 14 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:00: ioport range 0x1000-0x107f could not be reserved
pnp: 00:00: ioport range 0x1080-0x10ff has been reserved
pnp: 00:00: ioport range 0x1400-0x147f has been reserved
pnp: 00:00: ioport range 0x1480-0x14ff could not be reserved
pnp: 00:00: ioport range 0x1800-0x187f has been reserved
pnp: 00:00: ioport range 0x1880-0x18ff has been reserved
pnp: 00:01: ioport range 0x1c00-0x1c3f has been reserved
pnp: 00:01: ioport range 0x2000-0x203f has been reserved
ACPI: Power Button (FF) [PWRF]
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 112
ACPI: No ACPI bus support for i8042
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ACPI: No ACPI bus support for serial8250
ACPI: No ACPI bus support for serio0
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: No ACPI bus support for serio1
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[snip ...]
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: No ACPI bus support for 0.0
ACPI: No ACPI bus support for 0.1
Probing IDE interface ide1...
hdc: PLEXTOR DVDR PX-716A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: No ACPI bus support for 1.0
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level,
high) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
(scsi0:A:4): 20.000MB/s transfers (20.000MHz, offset 16)
(scsi0:A:6): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
ACPI: No ACPI bus support for 0:0:4:0
Vendor: IBM Model: DDYS-T36950N Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:6:0: Tagged Queuing enabled. Depth 32
ACPI: No ACPI bus support for 0:0:6:0
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [APC2] -> GSI 17 (level,
high) -> IRQ 17
Found Controller: IT8212 UDMA/ATA133 RAID Controller
FindDevices: device 0 is IDE
Channel[0] BM-DMA at 0x9800-0x9807
Channel[1] BM-DMA at 0x9808-0x980F
scsi1 : ITE RAIDExpress133
Vendor: ITE Model: IT8212F Rev: 1.45
Type: Direct-Access ANSI SCSI revision: 00
ACPI: No ACPI bus support for 1:0:0:0
[snip ...]
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <[email protected]>
ACPI: PCI Interrupt Link [APCM] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APCM] -> GSI 22 (level,
high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ACPI: No ACPI bus support for fw-host0
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22 (level,
high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 22, io mem 0xee083000
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: park 0
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ACPI: No ACPI bus support for usb1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: No ACPI bus support for 1-0:1.0
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level,
high) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 21, io mem 0xee087000
ACPI: No ACPI bus support for usb2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: No ACPI bus support for 2-0:1.0
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level,
high) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
ACPI: No ACPI bus support for 8a1cc7ffff0020ed
ieee1394: Host added: ID:BUS[0-00:1023] GUID[8a1cc7ffff0020ed]
ACPI: No ACPI bus support for 8a1cc7ffff0020ed-0
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 20, io mem 0xee082000
ACPI: No ACPI bus support for usb3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ACPI: No ACPI bus support for 3-0:1.0
eth1394: $Rev: 1247 $ Ben Collins <[email protected]>
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
usb 1-3: new high speed USB device using ehci_hcd and address 3
ACPI: No ACPI bus support for 1-3
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 4 ports detected
ACPI: No ACPI bus support for 1-3:1.0
i2c_adapter i2c-4: nForce2 SMBus adapter at 0x1c00
i2c_adapter i2c-5: nForce2 SMBus adapter at 0x2000
eth1: no link during initialization.
usb 2-1: new low speed USB device using ohci_hcd and address 2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
ACPI: No ACPI bus support for 2-1
ACPI: No ACPI bus support for 2-1:1.0
usbcore: registered new driver hiddev
[snip ...]
RPC: failed to contact portmap (errno -512).
mount shows
mount -t nfs blazebox:/home/paul /mnt/hd
mount: blazebox:/home/paul: can't read superblock
And the rpcinfo -p on host blazebox [ running FreeBSD 5.3-STABLE ] shows
program vers proto port
100000 4 tcp 111 portmapper
100000 3 tcp 111 portmapper
100000 2 tcp 111 portmapper
100000 4 udp 111 portmapper
100000 3 udp 111 portmapper
100000 2 udp 111 portmapper
100000 4 7 111 portmapper
100000 3 7 111 portmapper
100000 2 7 111 portmapper
100005 1 udp 752 mountd
100005 3 udp 752 mountd
100005 1 tcp 666 mountd
100005 3 tcp 666 mountd
100003 2 udp 2049 nfs
100003 3 udp 2049 nfs
100003 2 tcp 2049 nfs
100003 3 tcp 2049 nfs
100021 0 udp 751 nlockmgr
100021 1 udp 751 nlockmgr
100021 3 udp 751 nlockmgr
100021 4 udp 751 nlockmgr
100021 0 tcp 965 nlockmgr
100021 1 tcp 965 nlockmgr
100021 3 tcp 965 nlockmgr
100021 4 tcp 965 nlockmgr
100024 1 udp 879 status
100024 1 tcp 645 status
Trond has helped me before with debugging NFS
--
FreeBSD the Power to Serve!
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[Index of Archives]
[Kernel Newbies]
[Netfilter]
[Bugtraq]
[Photo]
[Stuff]
[Gimp]
[Yosemite News]
[MIPS Linux]
[ARM Linux]
[Linux Security]
[Linux RAID]
[Video 4 Linux]
[Linux for the blind]
[Linux Resources]
